User Manual - Paddle Palace
Contents
1. 5 Insert the Spin Indicator Panel into the slot of the net If you need to disassemble the net remove the Spin Indicator Panel first 6 Always unlock the robot wheels before moving the robot Roll the robot to the table Wheel Lock Paddle Palace H2W Touch Pro Robot User Manual How To Position the Table Tennis Robot The Power Supply 1 Clamp the net supports to both sides of the table near the net The robot is powered by standard US home current 2 Put both end sleeves of the ball 120V Make sure the collection net on the net supports power cord is securely plugged in On Off switch is located on the backside of the robot Turn off and unplug the robot when not in use 3 Buckle the rubber rings are to the outsides of the net support 4 Clamp the LCD Panel support to the edge of the table and insert the Touchscreen LCD Panel into the support Remove the protective film before operating the panel 5 Picture of a completed installation PULL 1 6 After training fold back the ball collection net in a reverse order of the original process lock the buckles and store in any suitable place Paddle Palace H2W Touch Pro Robot User Manual H2W Touchscreen LCD Panel Time Display the Main Menu Screen Frequency Adjust the current time v Picture 1 ball frequency Landing spots Functions Adjust the number of balls served the landing spots the SES type an2. within the acceptable temperature range The normal operating temperature of the touchscreen panel is from 10 degrees C to 60 degrees C The relative humidity for storing and transporting is 20 to 80 If the touchscreen panel is used or stored below the acceptable temperature relative humidity the surface may crystallize leading to unrecoverable damage If the touchscreen panel is used or stored above the acceptable temperature relative humidity the liquid crystal on the touchscreen may liquefy leading to unrecoverable damage 3 Do not open disassemble and reconfigure the panel This may damage the touchscreen and cause malfunction of the control panel 4 Keep the surface of touchscreen clean The surface may change color or have spot blot if water has been spilled and sits on the surface for a long time If the touchscreen has a spot or becomes dirty please clean it with a pure cotton or soft cloth Do not use gasoline alcohol or any chemical to wipe the surface 5 If any reason that you need to store the touchscreen panel for a long period we suggest you to do the following Place it in a dark area keep away from the strong light Do not put anything on the surface of the panel Do not store it in an area that exceeds the acceptable temperature relative humidity Warning To prevent the danger of fire electric shock personal injury and product damage children should be supervised while operating the robot Instruc
3. H PRO ROBOT Robot Components Features This manual has been written to help you enjoy and get the most out of your new Paddle Palace Robot Take time to read these pages thoroughly and keep it handy for reference when using your robot a PE rm Top Wheel Mis Ua Shooting Head 5 Bottom Wheel lt ___ Spin Indicator Panel LT bd a Ball Container top view Poke Bar Support Frame Ball Container The capacity of the Ball Container eZ is 100 40mm balls The container m should not be filled above the yellow line inside the container Anything other than table tennis balls in the Ball Container may damage parts and adversely affect e the robot s normal operation 4 8 S Pile Palace las Ball Collection Side Net Supports Ball Collection Touchscreen LCD Net Control Panel LCD Panel Support HE Paddle Palace H2W Touch Pro Robot page 5 User Manual How to Assemble the Ball Collection Net 1 Open the lock buckles of the ball collection net LL i fe 7g 2 Partially unfold the ball collection net and carefully slip it over the robot head Insert the double pin into the net support connector located on the robot frame Net Support Connector 3 Insert the pin in the ball collection net into the support frame of the robot ET mL 4 Spread out the ball collection net
4. Paddle Palace paddlepalace com 1 800 547 5891 503 777 2266 Paddle Palace The Paddle Palace H2W Touch Pro Robot is a very versatile and user friendly high tech robot The new LCD Touch Screen makes operation and programming of all functions of the robot very easy Get started in seconds using one of the 30 built in ball sequences with just a few touches on the screen Making your own custom sequences is also simple as the Touch Screen walks you step by step through the setup You can save up to nine of your own favorite custom sequences and you can easily modify the 30 built in sequences Whether you use built in sequences or your own custom sequences start up is easy every time you play 0 40 shooting head on the robot shows you the spin for each ball before it shoots This makes playing with the robot more like playing with a human partner as you can visually anticipate the spins on the upcoming balls The H2W Touch Pro Robot has two throw wheels with independently programmed motors allowing a great variety and degree of spins including topspin underspin sidespin and no spin Plus the robot can seamlessly shoot consecutive shots with different spins There are 22 possible landing te Spin Indicator 6 The new Spin Indicator Panel located just below the Bii 1 8 5 a spots on the table including short and l long balls making
5. ad to an irregular ball delivery CLEANING THE ROBOT Keep the table tennis robot clean The top and bottom friction wheels may become dirty after long use To ensure a quality serve please clean the wheels often with a damp towel picture 5 Always turn off the robot s power before cleaning Under normal condition the top and bottom friction wheels are able to work for 5 000 hours or longer before they need to be replaced When performing the replacement power off the robot remove the protective cover picture 6 and remove the screws from the friction wheel with a screwdriver clockwise to tighten counter clockwise to loosen picture 7 Do not use force to adjust the direction of the shooting head so as to prevent damage to the internal parts ay During an operation and or transportation protect the robot against any strong impact or oscillation Turn off the power and unplug the robot after you finish using the robot Paddle Palace H2W Touch Pro Robot page 12 User Manual Touchscreen Use and Maintenance 1 The touchscreen panel is a precise device that requires careful operation And the touchscreen is fragile so any strong impact or oscillation may damage the touchscreen Do not press too hard on the display area of the touchscreen When using or storing the panel please avoid any scratches caused by the hard objects on the surface of touchscreen 2 Please use and store the touchscreen panel
6. cannot make both selections at the same time Press the Total Ball Counts Timer button on the main menu The total ball counts Timer screen will appear picture 12 The default setting for Total ball counts is 000 Infinite serve ball Press UP or DOWN arrow to adjust the total ball counts from 001 999 Press the RIGHT ARROW to move from units to tens and hundreds To select Working time press the Working Time button picture 12 Use the UP or DOWN button to set the timer from 1 180 minutes NOTE the units are in minutes 001 sets the time to one minute 000 means Unlimited time After setting the ball counts or timer press BACK to save the current setting and return to the main menu Press START on the main menu the robot serves balls until the Total ball counts Timer reaches 0 When the counter hits 0 the robot will interupt play beeps and returns you to the main menu You can repeat the setting according the above procedure If you do not want to set the Total ball count press START and the robot will revert back to the default setting of infinite balls or time Custom Sequences Press the Custom Sequences button on the main menu The Custom Sequence screen will appear picture 13 Here you can program and save up to 9 different sequeces for later use Press UP or DOWN to choose from custom sequences 1 9 or select OFF
7. d amount of spin and the speed of S each shot e Total ball counts Timer Set the number or running time Settings Adjust lt eee the Volume Custom sequences Program your own a peed a sequences The 000 ge robot will recall and run up to 9 of your sequences with one touch Reset reset all settings to default Built in sequences Start Press this button to start Select from 30 pre the selected program programmed sequences Welcome Screen 1 wc Main menu functions Before using this product careiully read the safety warning inthe manual and Landing spots Functions adjust all the Function of each ball Frequency adjust the ball frequency follow the instruction to operate ze Total ball counts Timer set the number of balls to receive working time ss a Please press 5 Custom sequences program your own multifunctional sequence Build in sequences select the pre programmed sequence few seconds after turning on the robot a welcome screen will appear on the control panel see picture 2 Press Enter to go to the Main menu picture 1 Setting adjust the Volume Display brightness Language and Time Reset reset all settings to default 1 2 Start press this button to start the machine after setting the functions 09 28 00 Time display the current time Paddle Palace H2W Touch Pro Robot page 8 Settin
8. el The cable connecting to motor is loose Connect it with the original method Touchscreen has spot or has become dirty Clean it with a soft cloth Landing spot is unstable Dirt and wear on the top and bottom wheels after a Clean or replace the friction wheel period of time in operation The long and short ball sequence mode is selected Cancel the long and short ball sequence mode The shooting head is deflected by external force 7 777177 Paddle Palace H2W Touch Pro Robot page 14 User Manual List of Built In Sequences See page 10 for instructions for Built In Sequences Easy Set 1 10 2 short underspins to 10 spot 2 long topspins to 2 spot 2 short underspins to 1 spot 3 long topspins to 9 spot 2 short right side topspins to 10 spot 3 long topspins to 2 spot 2 short right side underspins to 5 spot 2 long topspins to 1 spot 2 short right side topspins to 2 spot 2 long topspins to 11 spot 2 short right side underspins to 4 spot 2 long topspins to 10 spot 2 short left side topspins to 10 spot 3 long topspins to 2 spot 2 short left side underspins to 10 spot 2 long topspins to 1 spot 2 short left side topspins to 2 spot 3 long topspins to 10 spot 2 short left side underspins to 2 spot 2 long topspins to 1 spot oO MP NN REN D gt 0 Intermediate Set 11 20 2 short underspins to 11 spot 1 long underspin to 2 spot 2 long topspins to 1 spot 1 short underspin to 9 s
9. for no setting Start with custom 1 Press Set Function The Function Setting of Serve Order screen will appear picture 14 Set the serving set landing spot spin top and bottom wheel speeds loop level and serve count After setting the function of the first serving set press the BACK button to return to the function screen picture 14 Set the functions for serving set 2 9 if needed Press the SAVE button to save the current settings and return to the main menu Press the START button in the main menu to start the routine To recall and play any of your custom sequences at a later date press the Custom Sequences button from the main menu Choose the Custom Number of the program you wish to use Press the BACK button to return to the main menu then press START Picture 10 Working Interface Screen Picture 11 Frequency 4 Picture 14 Function Setting of Serve Order Paddle Palace H2W Touch Pro Robot page 10 User Manual Custom Sequences Built In Sequences Built in sequences Press the Built In Sequences button on the main menu The Built In sequence selection screen will appear picture 5 There are a total of 30 numbered sets of pre programmed sequences Sequences 1 10 are the easiest 11 20 are harder and 21 30 are for the more advanced player Off means no setting will be applied Built in se
10. g Serve Order and Landing Spots User Manual Setting the Serve Order Press the Landing spots Function button on the main menu The functions setting serve order screen will appear picture 3 The number of balls served Landing Spots type and amount of spin and the speed of each shot are programmed starting with this screen You can program up to 9 different serving sets shot configurations The serving sets are played in order 1 9 then repeats until the robot is turned off To program the first serving set press button 1 on the Function setting of serve order screen picture 3 The orange color indicates the set selected The Landing spot screen will appear picture 4 Setting Landing Spots Choose a landing spot location from the 11 short and 11 long location buttons You can choose only one spot for each serving set press Delete to reselect a spot After pressing a landing spot button the Spins and Top Bottom wheel speed screen will appear picture 5 Spins and Top Bottom Wheel Speed 4 steps 1 Setting the spin Press the Spins button picture 5 Press the UP or DOWN button to choose the type of spin There are 9 types of spin to choose from Top spin under spin no spin dead ball left or right side spin left or right side spin top spin and left or right side spin under spin 2 Setting the Top and Bottom wheel speed Press the Top Wheel Speed button picture 6 to adjust the t
11. op throw wheel speed Press the Bottom Wheel Speed button picture 7 to adjust the bottom throw wheel speed Each wheel has 10 stages to choose from The combined top and bottom wheel speed settings determine the overall spin of the ball as follows Top wheel speed is higher than Bottom wheel speed top spin Bottom wheel speed is higher than top wheel speed under spin Top and bottom wheels set close to each other less or no spin 3 Setting the Loop Arc Press the Loop Level button picture 8 You set the angle of the shooting head from here There are 7 stages to choose from The higher the loop level stage is set the higher the shooting head will point This creates a bigger arc and in most cases an easier shot to return 4 Setting the serve count Press the Serve Count button picture 9 and then press the UP or DOWN buttons to select how many balls will be played in a serving set up to 9 0 is selected the system will skip this serving set You can make adjustments on some or all of the settings controlled using the buttons on this screen before continuing on to the next serving set in the sequence If no adjustment is made then it will show the default setting After making all settings for 1 serving set press BACK button to save the current settings for that set The functions setting of serving order screen will re appear picture 3 You can use the previous 4 steps to
12. possible any combination 1 of spins and landing spots you choose The LCD Touch H2W Touch Pro Robot is designed for the player Screen who wants a high quality long lasting robot that is easy to use yet offers the sophisticated technology for practicing the ideal training patterns to take your game to the next level Paddle Palace 4 NS X A H2W Touch Pro Robot includes Net Collection and Ball Recycling System Free 120 Nittaku training balls Free Robot Training DVD Free Shipping to contiguous USA 30 day money back Guarantee One year limited Warranty Paddle Palace H2W Touch Pro Robot page 3 User Manual Table of Contents 4 Robot Components Features 4 Capacity of the Ball Container 5 Howto Assemble the Ball Collection Net How to Position the Table Tennis Robot Ov O What Power Supply to Use N Main Menu Functions Description Landing Spots Functions Landing Spots Functions Spin and Top Bottom Wheel Speed Landing Spots Functions Serve Count Frequency Total Ball Counts Timer oO oO WO wo Custom Sequences 10 Built In Sequences 10 General Settings 10 Reset Default 11 Robot Maintenance 12 Touchscreen Use and Maintenance 12 General Warning Safety Issues 13 Troubleshooting 14 List of 30 Built In Sequences Paddle Palace paddlepalace com 1 800 547 5891 503 777 2266 Paddle Palace Table Top Pro Robot page 4 User Manual PADDLE PALACE H2W TOUC
13. pot 1 long underspin to 1 spot 2 long topspins to 10 spot 2 short underspins to 10 spot 1 long topspin to 2 spot 1 long topspin to 11 spot 1 short underspin to 11 spot 2 long underspins to 1 spot 2 long topspins to 6 spot 1 long underspin to 6 spot 1 short underspin to 11 spot 3 long topspins to 2 spot 2 short right side topspins to 10 spot 1 long topspin to 11 spot 2 long topspins to 1 spot 2 short left side underspins to 2 spot 2 long topspins to 11 spot 1 long topspin to 2 spot 2 short left side topspins to 10 spot 3 long topspins to 2 spot 1 long topspin to 11 spot 1 short right side underspin to 2 spot 1 long underspin to 10 spot 2 long topspins to 11 spot 1 long right side underspin to 2 spot 1 long underspin to 11 spot 2 long topspins to 3 spot 11 12 13 14 15 16 17 18 19 20 Advanced Set 21 30 1 short underspin to 10 spot 1 long underspin to 1 spot 1 long topspin to 5 spot 1 short underspin to 1 spot 1 long underspin to 11 spot 1 long topspin to 1 spot 1 long topspin to 10 spot 1 short underspin to 11 spot 1 short underspin to 7 spot 1 long underspin to 1 spot 2 long topspins to 9 spot 2 short underspins to 2 spot 1 long underspin to 10 spot 1 long topspin to 11 spot 1 long topspin to 5 spot 1 long topspin to 1 spot 2 long topspins to 9 spot 2 short underspins to 11 spot 1 long underspin to 2 spot 2 long topspins to 1 spot 1 long topspin
14. quences all have default settings and the Landing spot Spin Long Short ball and Serve count are pre set If you need to modify the Built in sequence press the Change Confirm button to load that sequence to the Function setting screen see Picture 16 You can now make changes on each function The modified Build in sequences can only be used temporarily When you exit the sequence or press the RESET button the modified setting will be erased and the settings will revert to the factory defaul settings See page 14 of this manual for the 30 Built In Sequence configurations 4 Picture 16 Function Setting of Serve Order General Settings General settings Press the Settings button on the main menu inc i a d The Setting screens will appear 0 er a pictures 17 18 19 20 From this 3 menu you can adjust the Volume This model does not have Volume control function Screen brightness Language English Simplified Chinese or Traditional Chinese 2 177 mA eme All changes will be applied when you ime press the BACK button and return to the main menu 4 Pictures 17 20 Volume Brightness Language Time Reset Default Reset default Press the RESET button on the Main Menu The reset screen will appear see Picture 21 Press YES button to restore all settings to the factory default WARNING when you press the YES b
15. set the second through ninth serving sets Press BACK to return to the main menu 04 28 00 4 Picture 3 Landing Spot Function 0202000000000 0880000000050 4 Picture 4 Landing Spot Screen 4 Picture 5 Spins 4 Picture 9 Serve Count Paddle Palace H2W Touch Pro Robot page 9 User Manual Setting the Frequency Total Ball Counts Timer Custom Sequences Press START on the main menu picture 1 The robot will begin to serve balls and the Working Interface screen will appear on the control panel picture 10 The Working Interface shows the current settings Setting the frequency The ball frequency can be set or changed before or during play Press the Frequency button on the main menu while the robot is in standby mode The Frequency screen will appear picture 11 Press UP or DOWN buttons to increase or decrease the ball frequency The ball frequency for this robot is between 28 and 95 balls per minute There are 10 stages to choose from After setting the frequency press BACK to save the setting and return to the main menu Press START button on the main menu picture 1 The robot begins to serve balls To adjust the ball frequency without interupting play press the Frequency UP or DOWN buttons from the Working Interface screen Setting the Total ball count In this menu you have two options to choose from Total balls count or working time NOTE You
16. tive advice should be given when machine used by children Avoid windy and or rainy days when using outdoors Use care when connecting and disconnecting the ball collecting net When robot is operating please keep away from the shooting head to avoid being hit with a ball When robot is operating if you observe something abnormal such as smoke coming out of the robot stop the robot and unplug it immediately Repair must be performed by a qualified repair person Do not remove the housing cover of the robot without authorization Some places on the robot will heat up during operation Please be careful and pay attention so as to avoid burning yourself Turn the power switch off and unplug the robot after use If any damage or loss is incurred due to the fact that safety instructions and regulation were not followed or the robot was not properly used as instructed in this manual our company will not take any responsibility Paddle Palace H2W Touch Pro Robot page 13 User Manual Troubleshooting FAILURE CAUSE SOLUTION Robot doesn t work Did not press Start button on the Main Menu Press Enter or Start to start Number in total ball count timer has reached 0 Press Start Robot works but does not release the balls It takes time to transport the balls from container Wait for a while to shooting head Pressed key failure Did not remove the protective film from Touchscreen Remove protective film Pan
17. to 6 spot 1 long topspin to 11 spot 1 short right side topspin to 10 spot 1 long underspin to 2 spot 2 long topspins to 10 spot 1 long topspin to 6 spot 1 short right side topspin to 2 spot 1 long underspin to 3 spot 1 long topspin to 8 spot 2 long topspins to 11 spot 1 short underspin to 1 spot 1 short underspin to 11 spot 1 long topspin to 2 spot 1 long topspin to 10 spot 1 short underspin to 1 spot 1 short underspin to 9 spot 1 long underspin to 2 spot 1 long topspin to 3 spot 1 long topspin to 10 spot 2 short right side underspins to 10 spot 2 short underspins to 1 spot 1 long underspin to 9 spot 1 long topspin to 11 spot 1 long topspin to 2 spot 21 22 23 24 25 26 27 28 29 30
18. utton all settings inthe Custom sequence modified Build in sequence and Landing spots Functions will be cleared The robot beeps several times when it has finished the process of resetting 4 Picture 21 Reset Screen Paddle Palace H2W Touch Pro Robot page 11 User Manual Robot Maintenance ELECTRONICS The robot s electric components are located in the machine s circuit board and the control box Therefore you should be careful to avoid dropping either component or avoid any activity that would cause damage to the internal electronic units of one or both of these components Keep liquids away from its surface in order to prevent damage to internal electronic units MECHANICS The robot s mechanical components are located in the mechanisms that produce the ball service and delivery Special attention should be paid so that no foreign objects are put into the ball container Foreign objects will block the robot s delivery wheel and result in damage to the robot REMOVING FOREIGN OBJECTS There is a view window fixed under the removable door You can open the removable door picture 1 remove the transparent guard plate picture 2 and take out any foreign objects picture 3 that have entered thus returning the robot to its normal operation POKE BAR When the poke bar inside the ball container picture 4 has worked for a long time it should be checked for loose screws so as to prevent any trouble that would le
Download Pdf Manuals
Related Search