SLIMLINE 2500 OWNER`S MANUAL
Contents
1. Page 20 SL 082411 TECHNICAL ASSISTANCE WhisperKOOL Customer Service is available Monday through Friday from 8 00 a m to 4 00 p m Pacific Time The customer service representative will be able to assist you with your questions and warranty information more effectively if you provide them with the following e The model and serial number of your WhisperKOOL Series Unit e Location of unit and installation details such as ventilation ducting construction of your wine cellar and room size Contact WhisperKOOL Customer Service 1738 E Alpine Avenue Stockton CA 95205 www whisperkool com Email support whisperkool com Phone 209 466 9463 US Toll Free 800 343 9463 Fax 209 466 4606 ACCESSORIES FOR COOLING UNITS WhisperKOOL offers accessories to enhance and customize your Slimline wine cooling unit ThruWall Room to Room Fan The ThruWall Room to Room Fan balances temperatures in adjoining rooms by transfering warm air out of exhaust room quietly and efficiently Simple to install in any frame wall from 3 1 2 to 6 3 4 thick A high quality Thermally Protected motor with balanced fan blade moves up to 200 CFM Move heated or cooled air between rooms Condensate Pump Kit The condensate pump kit is designed as an automatic condensate removal pump for water dripping out of our cooling units drain line The pump is controlled by a float switch mechanism that turns the pump on when approximately 2 1 4 of wate2. venience of managing the humidity enhancement of their wine cellar The WHM is one of the many Customer Preference Selection features which allow the customer the ability to fine tune the controls This feature is set to 0 when shipped but if needed can be adjusted Anti Short Cycle The Anti Short Cycle ensures that the unit will remain off for a period of 3 minutes after the unit has reached the set point to allow the pressure in the refrigeration system to equalize prior to starting the compressor Page 14 Anti Frost Cycle The Anti Frost Cycle is a precautionary measure as icing or frosting of the coil does not occur during normal operation The system will go through an anti frost cycle when the evaporator temperature reaches 26 During the Anti Frost cycle the unit will stop cooling and run the indoor fan to provide air flow across the indoor coil which will melt any frost accumulation Bottle Probe Failure Protection In the event that a bottle probe should fail the APST Advance Product Safety Technology will automati cally transition the Refrigeration Compressor cycles to a pre determined time series based on detailed laboratory testing which will ensure that the prod uct is kept within the safe range SL 082411 CONTROL FUNCTIONS Energy High Temp Pre Chill Reduction g P Low Temp Display N OFF Set Point ON 0 Button Symbol The ON OFF button allows the customer the convenience of turning the
3. the Control Operating System to their applicable choice The following CPSM options are available for adjustment Fon Humidity Management Enhancement This parameter is normally set at 0 which should pro vide adequate relative humidity for the cellar An increase in this parameter will increase the Humidity Enhancement RH and a decrease in the parameter will decrease Humidity Enhancement RH Adjustments should be made in increments of 5 with a maximum of 15 and a minimum of 0 After any adjustment to Humidity Enhancement you should wait a minimum of three days before making any additional adjustments This will allow the cellar sufficient time to acclimate to the new setting Fof Humidity Management Enhancement This parameter is normally set at 15 This parameter should not be adjusted as it simply provides an OFF cycle time for the fan during the compressor OFF cycle However the parameter is located within the CPSM as a convenience to the customer should it need to be adjusted CCS Cellar Pre Chill Set Point This parameter is set at 52 f but can be adjusted to a set point be tween 50 f 67 F CCT Cellar Pre Chill Duration This parameter is set to 6 hours but can be changed between 0 23 5 hours Con Cof Compressor On time Con and Off time Cof with a Probe 1 failure Alarm These parame ters are set at Con 40 min Cof 10 min In the event that there is a Probe 1 failure Alarm the compres sor refrige
4. 95205 8 ADDITIONAL TERMS AND CONDITIONS a Return Policy All return inquiries must be made within thirty 30 calendar days of the original purchase of a Product and are subject to a twenty five percent 25 restocking fee Shipping costs are not refundable and the Purchaser is responsible for all return shipping costs including customs fees and duties if applicable b WhisperKOOL retains a security interest in each Product until payment in full c Every provision of these Terms and Conditions shall be construed to the extent possible so as to be valid and enforceable If any provision of these Terms and Conditions is held by a court of competent jurisdiction to be invalid illegal or otherwise unenforceable such provision will to the extent so held be deemed severed from the contract of sale between Purchaser and WhisperKOOL and all of the other non severed provisions will remain in full force and effect d The laws of the State of California without regard for conflicts of law shall govern the construction and enforcement of the these Terms and Conditions except that these Terms and Conditions shall be interpreted as through drafted jointly by WhisperKOOL and Purchaser Any dispute will be resolved by the courts in the County of San Joaquin State of California and all parties WhisperKOOL Purchaser and End User hereby irrevocably submit to the personal jurisdiction of such courts for that purpose No waiver by WhisperKOOL of
5. THE WINE CELLAR The performance and life of your WhisperKOOL unit is contingent upon the steps you take in preparing the wine cellar Note Improperly preparing your enclosure or incorrectly installing your WhisperKOOL unit may cause unit failure leaking of condensation and other negative side effects IT IS HIGHLY RECOMMENDED THAT YOU OBTAIN THE ASSISTANCE OF A WINE STORAGE PROFESSIONAL Wine storage professionals work with licensed contractors refrigeration technicians and racking companies to build well insulated beautiful and protective wine cellars WhisperKOOL has put together some useful tips to assist in the installation process Our recommendations are meant to act as a guide in the process of building a proper enclosure Your intended location may have specific needs that we do not address How to Build a Wine Cellar Instructional Video WhisperKOOL has a construction tutorial available on line at our website www whisperkool com This tutorial will walk you through the steps of constructing a properly built wine cellar and the installation of our WhisperKOOL product line Wall amp Ceiling Framing Build wine cellar walls using standard 2x4 or 2x6 construction methods and ceiling joists following the guidelines of local and state codes in your area As a general rule the thicker the walls and the higher the insulation value in your cellar the better it will be at maintaining a consistent temperature Insulation Insulation
6. The moist air can cause mold to form and standing water in drain pans promote microbial and fungal growth that cause unpleasant odors and indoor air quality problems If mold is found remove it immediately and sanitize that portion of the unit Page 7 Mounting the Unit The unit must be mounted within 18 of the top of the room in order to achieve sufficient cooling As the room cools down the warm air will rise to the ceiling Mounting the WhisperKOOL high in the room will create a consistently cool environment by capturing the warm air and replacing it with cool air Mounting the unit low in the room will result in a temperature variation in the room due to the unit s inability to draw warm air from the ceiling of the cellar to the unit itself and cold air settling to the floor Exhaust Fan Vent optional Air Intake optional Keep Clear Exhaust Area Unobstructed Airflow Unobstructed airflow too and from the unit is critical for the unit s overall performance and life span A mini mum three foot clearance five foot is ideal area is crucial The air the fans blow needs to circulate and either dissi pate or absorb heat from the space the more air to exchange the more efficient the system will operate Note Avoid attempting to camouflage the unit This will restrict airflow and thus the unit s ability to work efficiently Door and Door Seal An exterior grade 1 3 4 door must be installed as a cellar doo
7. any breach or default of the contract of sale including these Terms and Conditions concerning a Product will be deemed to be a waiver of any preceding or subsequent breach or default 9 Questions or Additional Information If you have any questions regarding these Terms and Conditions or wish to obtain additional information contact us via phone at 1 800 343 9463 or please send a letter via U S Mail to WhisperKOOL 1738 E Alpine Ave Stockton CA 95205 support whisperkool com Model Serial Number A Installed by Date Page 24 SL 082411 WhisperKOOL WhisperKOOL 1738 E Alpine Ave Stockton CA 95205 1 800 343 9463 www whisperkool com
8. is REQUIRED with the use of the WhisperKOOL product Standard fiberglass or rigid foam insulation is nor mally used in cellar construction or in some cases blown in insulation is used It is very important that all walls and ceilings are insulated to keep the cellar temperature as consistent as possible during the summer and winter months The R value or quality of insulation is determined by the rate at which heat passes through the insulation The higher the R value the more resistant the insulation is to conducting heat Using higher R values in insulation will lower your operating costs and unit run time R 13 minimum R 19 recommended R 30 for ceiling and exterior walls Vapor Barrier A vapor barrier is REQUIRED to prevent the intrusion of water vapor so that the cellar can be kept at the correct temperature and humidity 6 mm plastic sheeting recommended should be applied to the warm side of the cellar walls The vapor barrier must also be applied to the outside walls and ceiling If it is impossible to reach the outside then the plastic must be applied from within the cellar The most common method is to wrap the entire interior leav ing the plastic loose in the stud cavity so the insulation can be placed between each stud All of the walls and ceiling must be wrapped in plastic for a complete vapor barrier In areas of high humidity such as Southern and Gulf States the vapor barrier will prevent infiltration of warm moist air
9. refrigeration system ON or OFF from the control panel This feature does not disconnect power from the unit In order for the power to be shut off from the unit the power cord must be unplugged from the wall receptacle Press the ON OFF button once for button application Up and Down Use these buttons to scroll up or down the CPSM Customer Preference Selection Mode Arrows menu Displays the Highest and Lowest temperature sensed by the Bottle Probe This feature amp allows the customer instant access to the recorded data applicable to the Bottle Probe VAN Temperatures it can be easily reset to reflect current temperatures Press the UP arrow or the Down arrow once and the Highest or Lowest Temperature Hi Lo sensed by the Bottle Probe will be displayed NZ To reset the Hi Lo press and hold the Set button when the Hi Lo value is displayed on the Digital Display continue to hold the Set button until rst appears on the digital display and then blinks This will erase the past recorded Temperature Data History and start recording from the current time and temperature forward Temperatures displayed would reflect Bottle Probe Temperatures from that point in time and beyond The Hi Lo feature should be reset at initial Start Up and after the Cellar or Cabinet has obtained normal operating temperatures which is generally 55 F Cellar PreChill CPC The CPC Feature is activated by pressi
10. ID MEASURING THERMOSTAT SYSTEM The WhisperKOOL Slimline cooling unit comes equipped with a liquid temperature measuring thermostat system The probe contains a sensor chip which actually communicates back and forth to the thermostat This results in a consistent temperature setting and accuracy Do not remove the tip from the probe To Use the thermostat 1 Locate an empty wine bottle 2 Fill 3 4 full with room temperature tap water 3 Place bottle probe securely into bottle 4 Place bottle with probe level and to the side of the unit in your wine cellar Avoid pulling too much on the probe cord It may become disconnected resulting in non operation of the unit Note The thermostat can be set between 45 F and 67 F Remember The WhisperKOOL System is based on the temperature of the water By measuring the liquid temperature rather than air the unit will oper ate 75 80 of the time Page 13 SYSTEM OPERATION Initial Start Up When power is applied to the unit the control will briefly display all symbols and the Compressor symbol will be displayed if unit is calling for cooling There may be a brief delay prior to the evaporator and condenser fans turning on Normal System Cycle After the bottle probe has reached the set point all units are shipped with the set point of 55 F and a dif ferential of 1 F the unit turns off The WHM is an ad justable feature which allows the customer the con
11. SLIMLINE 2500 OWNER S MANUAL WhisperKOOL The Coolest Thing In Wine Stor We manufacture test and certify 100 of our wine cooling units in the USA By sourcing the best components and closely controlling our manufacturing processes we can assure the highest quality lowest defect manufacturing rates in the industry Copyright 2011 Vinoth que Wine Cellars All rights reserved This manual the product design and the design concepts are copyrighted by Vinotheque Wine Cellars with all rights re served Your rights with regard to the hardware and manual are subject to the restrictions and limitations imposed by the copyright laws of the United States of America Under copyright laws this manual may not be copied reproduced translated transmitted or reduced to any printed or electronic medium or to any machine readable form for any purpose in whole or in part without the written consent of Vinoth que Wine Cellars Every effort has been made to ensure that the information in this manual is accurate Vinotheque Wine Cellars is not respon sible for printing or clerical errors Vinoth que Wine Cellars reserves the right to make corrections or improvements to the information provided and to the related hardware at any time without notice Vinoth que and WhisperKOOL are registered trademarks and ECE is a trademark of Vinotheque Wine Cellars All rights re served Mention of third party products is for informational purpose
12. a that it is exhausting to does not exceed 85 F Therefore you want to exhaust the unit in a room which will not exceed 85 F preferably at 75 F otherwise the unit will not have the capacity to keep the wine at a desirable 55 F Warning allowing your system to operate in high ambient temperatures for extended periods of time will greatly decrease the life of your system and void your warranty Drain Line All units come with a drain line for additional removal of excessive condensate This is a back up system to the Condensate Evaporator It is mandatory to install the drain line attachment During operation the cooling unit will strip excess water from the air in order to maintain the proper level of humidity within the cellar The Condensate Evaporator will heat and dissipate the excess moisture through the rear of the unit However in extreme humidity additional condensate will be created Conversely the high humidity air has less capacity to absorb additional moisture through the exhaust of the unit Thus the drain line will prevent overflow and leaking by allowing for discharge of the additional condensate WhisperKOOL carries a condensate pump kit which allows the excess condensate to be pumped up to 20 ft away from the unit Page 9 PRE INSTALLATION Skill level Moderate Follow the local building codes and or consult a license contractor Electrical Needs The WhisperKOOL System requires a dedicated 110 volt 20 amp circuit The uni
13. age 15 Press the Set button once and it will display the Set Point After approximately 5 sec onds the display will return to normal operation and display the Bottle Probe tempera ture Standard Controller Press and hold the Set button for 3 5 seconds until the set point is displayed and the F symbol starts blinking Next press the UP or Down arrows to change the Set Point Next press the Set button once and the Set Point numbers and the F on the display will blink to confirm the new Set Point setting Press and hold the Set button during the display of the Hi Low Temperature Data His tory hold button unit rst blinks on display and it will erase the past recorded data file and start recording from the current time and temperature Press the Set and the Down Arrow buttons simultaneously for 10 15 seconds and you will access the Customer Preference Selection Mode CPSM The CPSM allows the customer to Fine Tune the Control Operating System to their applicable choice Anti Frost The Anti Frost Cycle is automatically activated when the evaporator temp has reached a low temp of 26 and has sustained that temp for a period of five minutes During this cycle the AUX compressor and condenser fans will turn off and the evaporator fans will continue to run Once the temperature of the evaporator gets back up to 40 the cycle will deactivate and the system will rever
14. d or return air on evaporator or condenser side of the unit Remove air flow obstruction Unit is mounted too low in the cellar Re Locate unit so the distance from the ceiling and top of the unit is no more than 18 One or more of the fans are not turning on Call Customer Service at 800 343 9463 Compressor is not turning on Call Customer Service at 800 343 9463 Compressor keeps cycling on overload Make sure all fans are working and there are no airflow obstruction Poor seal around door Make sure there are no air gaps around the door If door seal is damaged replace it Controller set too high Lower the set point Evaporator coil is frosted or iced up Observe ice formation pattern If only part way up the coil face unit could be low on refrigerant If so call Customer Service at 855 235 5271 Page 19 TROUBLESHOOTING GUIDE Possible Cause Solution Unit is not level Unit should be level in wall to prevent leaking Drain line clogged or kinked Check drain line to make sure water can flow freely Drain is clogged preventing water form escaping Disconnect drain and clear out Drain line does not have a downward slope Fix Drain line so there is a downward slope from the unit to the drain Coil is iced causing drain pan ice and water overflowing Melt ice with blow drier Soak up with a towel Possible Cause Solution Lack of air flow Make sure fan is unobstructed clean evaporator
15. e is WhisperKOOL s quietest interior venting self contained unit available designed to mount in a living area Developed to fit into the often unused space between the cellar door and ceiling giving the collector maximum stor age capacity The system is equipped with WhisperKOOL s Platinum Series controller utilizing Advanced System Protec tion Technology This features a series of strategically placed monitoring probes which ensure efficient performance and long cooling unit life With efficiency in mind the Slimline uses less power than most traditional units while having the ability to cool cellars up to 350 cubic feet Customer Service Thank you for purchasing a WhisperKOOL Slimline cooling unit We strive to provide the highest quality products and the best possible customer service If you have any questions about your WhisperKOOL unit please call us at 1 800 343 9463 Using the Manual This User s Manual is intended to assist in the proper installation and maintenance of the WhisperKOOL Slimline cool ing system In order to ensure the longevity of your cooling unit the equipment should be installed properly and have a proper care and maintenance schedule Please read and review this manual carefully and keep it for future reference What Is the WhisperKOOL Slimline Cooling System The WhisperKOOL Slimline system is a specialized refrigeration unit designed for one purpose only to maintain the optimal temperature and humidity levels c
16. ed for an additional three 3 year period with regard to a WhisperKOOL Product s compressor only Labor freight and parts ancillary to the compressor remain subject to the two 2 year limited warranty C Product Warranty Limitations and Exclusions 1 This limited warranty does not cover cosmetic damage caused during installation damage due to acts of God commercial use accident misuse abuse negligence or modification to any part of the Product Delivery and installation of the Product any additional parts required as well as removal of the Product if warranty work is required are all at the sole cost risk and obligation of the End User 2 This limited warranty does not cover damage due to improper installation or operation or lack of proper maintenance of the Product connection of the Product to improper voltage supply or attempted repair of the Product by anyone other than a technician approved by WhisperKOOL to service the Product 3 This limited warranty does not cover any Product sold AS IS or WITH ALL FAULTS Page 22 SL 082411 4 This limited warranty is valid only in the continental United States Alaska and Hawaii Sales elsewhere including Puerto Rico are excluded from this warranty 5 Proof of purchase of the Product in the form of a bill of sale or receipted invoice which is evidence that the Product is within the Limited Warranty Period must be presented by the End User to WhisperKOOL in order to ob
17. f the Product Installation Requirements Maintenance Requirements and End User Requirements may at WhisperKOOL s sole discretion void this limited warranty 11 No one has any authority to add to or vary the limited warranty on this Product 3 PRODUCT INSTALLATION REQUIREMENTS a Prior to installing a WhisperKOOL Product the End User must read the WhisperKOOL Owner s Manual and thereafter the End User must follow the required installation use and maintenance procedures set forth by WhisperKOOL in WhisperKOOL s Owner s Manual The Owner s Manual is shipped with each Product and if another copy is needed replacement copies can be downloaded from WhisperKOOL s website www whisperkool com or by contacting WhisperKOOL directly for a new copy of the Owner s Manual b It is highly recommended that the End User obtain the assistance of a wine storage professional c Failing to address all of the variables associated with proper installation will cause the Product to operate incorrectly and limit both the Product s ability to cool and the longevity of the Product itself d The limited warranty card should be completed and promptly returned by the End User to WhisperKOOL to ensure limited warranty registration and confirmation of date of purchase e The End User is responsible for all risks and costs of installation of the Product including but not limited to all labor costs as well as cost of any additional parts required for the proper and c
18. if necessary Compressor not running Call Customer Service at 800 343 9463 Unit undersized Call Customer Service at 800 343 9463 Fans run but compressor does not Compressor may have overheated Shut unit off for 1 hour to allow compressor to cool Turn back on and check for cooler air flow out If compressor runs check for and clean condenser coil as possible cause of compressor overheat ing If problem repeats call customer service Possible Cause Solution Compressor and or starting components faulty Call Customer Service at 800 343 9463 Fans run but compressor does not Compressor may have overheated Shut unit off for 1 hour to allow compressor to cool Turn back on and check for cooler air flow out If compressor runs check for and clean condenser coil as possible cause of compressor overheat ing If problem repeats call customer service Possible Cause Solution Faulty fan motor Call Customer Service at 800 343 9463 Faulty fan relay Call Customer Service at 800 343 9463 Possible Cause Solution Evaporator fans blow on bottle probe Move bottle probe to a more central location Unit low on refrigerant charge Call Customer Service at 800 343 9463 Condensing fan motor capacitor faulty Call Customer Service at 800 343 9463 Compressor and or starting components faulty Call Customer Service at 800 343 9463 Possible Cause Solution Cellar vapor barrier not sufficient Install proper vapor barrier
19. llar side with the thermostat facing inside The outer flange should be flush to the wall Secure the flange to the wall through the pre drilled holes The screws should penetrate the studs and or frame as well as the upper and lower supports to provide adequate support for the WhisperKOOL system Power Seal all cracks and gaps around the unit with an air tight sealant or caulking to prevent air leakage Bottle Probe Drain line Note If you use decorative molding it should be attached to the walls and never to the cooling unit STEP 5 Attach the condensate drain line The condensation drain line tube is used to remove excess condensation from the unit to a proper discharge loca tion It is important that the drain line tube is properly connected and used to prevent leakage and other problems associated with excess condensation Failure to use the condensation drain line tube will void the warranty on the unit bates Note To prevent mold from growing allow the drain line to Drain line is above possible hang above the water line water level A Failure to install the drain line voids warranty WRONG Drain line To prevent mold from growing allow the drain line to is under water hang above the water line STEP 6 If removed install the grille s on both sides of the unit and plug in the power cord The use of an extension cord is not recommended Page 12 SL 082411 LIQU
20. mount of liquid dish washer detergent Spray coil let set for 5 min then flush with fresh water There is something blocking the supply and or return air Remove blockage One or both evaporator fans are not turning on Call a service tech to troubleshoot The temperature of the room the unit is exhausting to has Raise the temperature of the exhaust room dropped below 50 The unit has not gone through its anti frost sequence yet Check for ice in the depth of the coil Melt with blow drier until coil is warm to the touch Soak up water with a towel If unit continues to ice Observe ice formation pattern If only part way up the coil face Possible Cause unit could be low on refrigerant If so call Customer Service at 800 343 9463 Solution Unit is not plugged in Make sure the unit is plugged into an outlet Power switch not on Turn unit on by pressing the power button on the control Line voltage is incorrect rating for unit Room at set point Thermostat not calling for cooling Faulty thermostat or wiring Possible Cause Check line voltage to make sure there is 110v 120v Lower set point Lower set point Call Customer Service at 800 343 9463 Solution The temperature or the room unit is exhausting to has exceeded 85 Lower the temperature of the exhaust room The unit is undersized for the room Order correct size unit There is something blocking the supply an
21. nd Users should satisfy themselves that the Product they are purchasing is suitable for their particular needs and requirements and thus no responsibility will be placed with WhisperKOOL for the End User s decisions in this regard b It is the End User s responsibility to secure safe haven storage for ANY AND ALL items that are being kept and stored in the End User s wine cellar including any Product WhisperKOOL takes no responsibility for the safety and preservation of the aforementioned items in the event that the environment becomes unsuitable to maintain a proper storage environment Page 23 6 SALES AND USE TAX WhisperKOOL only collects California sales tax for orders shipped within the State of California WhisperKOOL does not collect sales tax for orders shipped to other states However the Purchaser and the End User may be liable to the taxing authority in their state for sales tax and or use tax on the Product The Purchaser and the End User should each check with their state s taxing authority for sales and use tax regulations 7 CUSTOMER SERVICE AND TROUBLESHOOTING WhisperKOOL s customer service department is available to answer and questions or inquiries for End Users regarding a WhisperKOOL Product as well as to assist in performing basic troubleshooting Monday through Friday from 8 00 a m to 4 00 p m PST at telephone number 1 800 343 9463 WhisperKOOL Corporation is located at 1738 East Alpine Avenue Stockton California
22. ng the Up button for 3 5 seconds and the CPC logo will be displayed on the digital display The CPC feature can be terminated by pressing the Up button for 3 5 seconds or the feature will self terminate after 6 hrs Boe ES 1 The CPC Feature may be used to Pre Chill the Cellar prior to loading it with Warm Product The feature will shift the Set Point down to a lower setting of 52 F for the next 6 hours After the 6 hour time period the Set Point will automatically return to the original Set Point The CPC feature can be conveniently adjusted to the customer s specific needs by ac cessing the Customer Preference Select Mode CPSM See Customer Preference Select Mode Instructions Energy Reduction 1 The ER feature is activated by pressing the ER button one time and the ER logo will ap ER pear on the digital display The purpose of the ER feature is to reduce energy cost by shifting the Set Point up by 4 68 ze degrees which will allow the cooling system to run for shorter periods of time resulting in a reduction in energy cost The ER feature allows for Energy Savings at any time During periods of high ambient temperatures vacations or business travel To deactivate the ER feature press the ER button one time and the ER logo will turn off The ER feature can be conveniently adjusted specific need by accessing the Customer Preference Select Mode CPSM See CPSM Instructions on the next page P
23. nplug the unit from the electrical outlet Units weigh 50 pounds and are cumbersome for one person to carry We recommend that you get someone else to help you during the installation process NEVER LAY UNIT ON ITS SIDE Note If the system does not seem to be running cool after 15 minutes please refer to the Troubleshooting Guide on Page 19 Page 10 SL 082411 PREPARING THE INSTALLATION LOCATION Minimum Tools Needed Level Hammer Screwdriver Note The following installation examples are for reference only door header construction and framing may vary When not installing above a door adequate framing inside of the wall is necessary WhisperKOOL recommends consulting a licensed contractor for framing and construction needs minimum 4 from ceiling Locate the desired installation location using a level and a pencil mark a center line o Center Line Mark the center line for your desired installation location followed by laying out the hole for the unit Hole size 22 1 2 inches by 10 3 4 inches minimum 1 from door casing Door Opening Cut out the drywall and studs for the unit opening Warning Use caution not to cut through any electrical or plumbing In most cases framing will need to be added to provide adequate support for the unit and mounting bracket Page 11 INSTALLATION STEP 4 CELLAR SIDE Slide the cooling unit in from the ce
24. ntly cool down the temperature of the cellar over time by cycling cooler and cooler air throughout Test the unit prior to installation Operate unit for twenty minutes While the unit is running and working properly the air discharged from the front should be 10 15 F cooler than the air in the room This means that in an environment where the air is 80 F the unit will discharge air that is 65 70 F 6 It is REQUIRED to install a drain line to remove condensation from the unit 7 The WhisperKOOL unit is intended for use in properly designed and constructed wine cellars Hire a professional wine storage consultant with a valid contractor s license to build your wine cellar Refer to the How to Build a Wine Cellar video available on the WhisperKOOL website at www whisperkool com 8 Install the foam strips along the inside edge of the unit s flange to assure a proper seal against the wall Never try to open the WhisperKOOL unit repair it yourself or use a service company without WhisperKOOL s authorization This will void your warranty If you encounter a problem with your WhisperKOOL unit please refer to the Troubleshooting Guide If you have any further questions concerns or need assistance please contact WhisperKOOL Customer Service at 1 800 343 9463 ext 799 Please be sure all testing has been completed prior to contacting Customer Service Please have your results ready for your representative Page 6 SL 082411 PREPARING
25. omplete installation of the Product The End User is responsible for all risks and costs of removing the Product if limited warranty work is required f The Product cannot operate at its optimum capacity if airflow is constricted by ducting or venting the exhaust side of the Product into a location with inadequate ventilation 4 MAINTENANCE REQUIREMENTS It is the End User s responsibility to clean off any accumulated dust lint or other debris from the front and rear intake grills failure to do this on a regular basis will restrict the airflow and may affect the Product s ability to function properly Periodically cleaning the Product s vents will help assure maximum cooling efficiency The drain tube must also be checked and kept clean and free of debris and mold to maintain proper performance Mold is a natural living organism in the environment It exists in the air in the form of microscopic spores that move in and out of buildings through doors windows vents HVAC systems and anywhere else that air enters Once it is discovered mold must be addressed quickly and appropriately Delayed or improper treatment of mold issues can result in costly and reoccurring repairs If the End User suspects a mold problem it is always best to hire a qualified and experienced mold remediation specialist 5 ADDITIONAL END USER RESPONSIBILITIES The following items are not covered under any warranty and are the sole responsibility of the End User a E
26. onducive to the proper storage and aging of fine wines It is a self con tained cooling unit designed to be used as a forced air through the wall unit How Does the WhisperKOOL Slimline Work The WhisperKOOL Slimline cooling system is especially designed for the use and application to maintain optimal con ditions for wine storage and aging The system is specially designed for slow cooling this greatly reduces the amount of humidity removed from the cellar Temperature Setting The WhisperKOOL Slimline unit can be set at any temperature within the acceptable wine aging range of 45 F to 67 F It is designed to cool up to 30 F cooler than the ambient temperature of the space to which it is exhausting Page 4 SL 082411 RECEIVING amp INSPECTING THE UNIT Receiving and Inspecting the Unit e Lift only at the designated handhold locations on the shipping container or fully support the unit from under neath A shipment may include one or more boxes containing accessories e Before opening the container inspect the packaging for any obvious signs of damage or mishandling e Write any discrepancy or visual damage on the Bill of Lading before signing e Place the box containing the WhisperKOOL unit on a tabletop to prepare it for testing prior to installing e Sit upright for 24 hours Note WhisperKOOL units are manufactured in the USA and tested prior to shipment Review the Packing Slip to Verify Contents e Check the model number to ensu
27. r It is very important that weather stripping is at tached to all 4 sides of the doorjamb A bottom sweep or threshold is also required The door must have a very good seal to keep the cool cellar air from escaping out of the cellar One of the most common problems with cooling units running continually is due to the door not sealing properly Page 8 SL 082411 Ventilation The necessity of dissipating heat away from the unit is critical to the unit s performance and cannot be overstated As the unit operates and cools a greater amount of heat is generated on the exhaust side of the unit Adequate ventila tion is required in order to dissipate heat away from the unit If ventilation is inadequate the exhaust will heat up the area or room and adversely affect the unit s ability to cool In some cases it may be advisable to install a vent fan to dissipate heat within the exhaust area on the backside of the unit However you must have a fresh air inlet as well Note If you are unsure about having adequate ventilation in your install location please contact us to assess your specific installation at support whisperkool com or 1 800 343 9463 Back Exhaust Room Front Wine Cellar Exhaust Fan WhisperKOOL bo side view v 55 F MAX A aN A X Air Intake Cellar Wall Ambient Temperature Factor The cooling system has the ability to cool a wine cellar efficiently to 55 F as long as the ambient temperature of the are
28. r collects in the tank and automatically switches off when the tank drains to approximately 1 1 4 The condensate pump kit allows the excess condensate to be pumped up to 20ft away from the unit Accessories can be purchase at www whisperkool com Page 21 INSTALLATION TERMS AND CONDITIONS WhisperKOOL Cooling System WHISPERKOOL PRODUCT BASE TERMS WhisperKOOL Corporation WhisperKOOL is in the business of manufacturing and selling wine cabinets cooling units and related goods each such wine cabinet cooling unit and related good is referred to herein as a Product As used herein the term WhisperKOOL includes any Product sold under the names WhisperKOOL Vinotheque and CellarCool Purchaser means the original purchaser of aWhisperKOOL Product End User means the consumer who has installed and is actually using a WhisperKOOL Product Every sale of a Product from WhisperKOOL to a Purchaser is made subject to these Terms and Conditions of Sale Terms and Conditions Product prices are specified in the WhisperKOOL published price list that is current at the time WhisperKOOL receives Purchaser s particular order Prices are subject to change at any time prior to WhisperKOOL s acceptance of Purchaser s particular order No contract of sale exists until WhisperKOOL has accepted Purchaser s order and provided Purchaser with a written acknowledgment of Purchaser s order Prices are exclusive of and Purchaser shall pa
29. ration system automatically starts a predetermined ON OFF cycle which is controlled by the Con and the Cof parameters The customer can adjust these parameters to maintain the desired Bottle temperature Hes Differential for Energy Reduction This parameter is set at 4 above the set point during the Energy Reduction mode A decrease in this setting will decrease the set point and an increase in this feature will increase the set point Page 17 MAINTENANCE SCHEDULE It is the user s responsibility to remove any accumulated dust lint or other debris from the front and rear intake grilles This will restrict the airflow and may affect the unit s ability to function properly Periodically cleaning the unit s vents will help assure maximum cooling efficiency The drain tube must also be checked and kept clean and free of debris and mold to maintain proper performance Monthly 1 Check for unusual noise or vibration 2 Check the drainline to see if it is above the waterline if draining into a vessel Quarterly 1 Clean front and rear intake grilles Annually 1 Use a vacuum with brush attachment to clean grilles 2 Inspect for corrosion 3 Check wiring connections and integrity of cords 4 Pour a 50 50 bleach solution into the drainline every spring Page 18 SL 082411 TROUBLESHOOTING GUIDE Possible Cause Evaporator coil is dirty Clean coil with a vacuum If coil is very dirty use a small hand spray with a small a
30. re it is correct e Check that all factory options ordered are listed If any items listed on the packing slip do not match your order information contact WhisperKOOL Customer Service immediately Check the Box for the following contents Mounting Brackets 2 Accessory Kit One e WhisperKOOL Slimline Owner s Manual e Bottle Temperature Probe Accessory Kit Two e 1 2 Self Tapping Screws 4 e 13 4 Hex Head Screws 4 e Drain Line tube with Brass Connector e Insulation Foam Strips 4 Please leave the WhisperKOOL unit in its original box until you are ready for installation this will allow you to move the product safely without damaging it TIP Save your box and all packaging materials They provide the only safe means of transporting shipping the unit Page 5 QUICK START GUIDE This guide is meant to serve as a quick reference for installation of the WhisperKOOL unit The remainder of this Owner s Manual will provide more detailed information and instructions Upon receiving the WhisperKOOL unit 1 Inspect the unit before installation If damage is found please contact your distributor or WhisperKOOL Customer Service at 1 800 343 9463 ext 799 2 The unit should remain in an upright position for 24 hours prior to operation 3 The WhisperKOOL unit requires a dedicated 115 volt 20 amp circuit Use a surge protector with the WhisperKOOL unit Do not use a GFI Ground Fault Interrupter line 4 The unit is designed to ge
31. s only and constitutes neither an endorsement nor a recommen dation Vinoth que Wine Cellars assumes no liability with regard to the performance or use of these products 08 24 11 SL 082411 TABLE OF CONTENTS Quick Reference Guide Receiving amp Inspecting The Unit Quick Start Guid ii s5cscs medapeesdeteedeteubeeaditeaden Preparing the Wine Cellar 0 ee eee Through the Wall Installation Pre installation ciiscoicsretas tarde vetasieweidoeksaonase Preparing the Installation Location HASTEN ARON ernn aa aai Liquid Measuring Thermostat System aaeeea System Operation 0 cece eee eee eee Control Functions 00 e cece cece cence eens Maintenance Schedule ccecee eee e eee Troubleshooting Guide 00 cece cece eee eee Technical Assistance amp Accessories 065 Installation Terms and Conditions Page 1 QUICK REFERENCE GUIDE Front Side View in cellar evaporator a Bottle Probe Probe Input Controller Power Cord w O a pa an Bottom View Rear Side View out of cellar condenser Probe Input A Power Cord SL 082411 Page 2 QUICK REFERENCE GUIDE Note The 1 or 3 5 qualifies the amount of time in seconds that the button m
32. t back to normal operating conditions 6 6 At the beginning of the cycle the AUX symbol will be illuminated and the SA symbol is illuminated during the anti frost cycle The Alarm symbol is shown when the system encounters an issue that needs attention the displayed alarm codes are explained below Alarm Codes message cause osoon OOOO O O Bottle Probe is Unplugged Attach Bottle Probe to Unit Faulty Bottle Probe Connection 1 Check Bottle Probe attachment at circular connector 2 Check Bottle Probe connection at green terminal block on back of controller Defective Bottle Defective Bottle Probe Replace the Bottle Probe Faulty Evaporator Probe Check Evaporator Probe connection at green terminal block on back of a ea controller Defective Defective Evaporator Probe Probe Replace the Evaporator Probe HA Defective Bottle Probe Replace the Bottle Probe The Bottle Probe is sensing a Allow the room to warm up which will increase the temperature of the LA temperature of 4 below the set wine point Defective Bottle Probe Replace the Bottle Probe The keypad is locked Hold Up and Down buttons for 3 to 5 seconds to disable PON should appear Page 16 SL 082411 CPSM Mode Press the Set and the Down Arrow buttons simultaneously for 10 15 seconds and you will access the Customer Preference Selection Mode CPSM The CPSM allows the customer to Fine Tune
33. t draws a large amount of amps at initial start up By designating a dedicated circuit breaker you will guarantee the unit has enough power to run ef fectively Contact an electrician for assistance with the installation of this dedicated electrical circuit 1 Match the electrical outlet to the plug provided on the WhisperKOOL unit 2 Provide a dedicated circuit and wiring for the unit Electrical Outlet The unit is equipped with a twelve foot power cord located on the evaporator side of the unit Plug your Whis perKOOL unit into a surge protector or power conditioner As with any sensitive electrical equipment the Whis perKOOL electrical equipment may be damaged by power surges and spikes Power surges and spikes are not cov ered in the WhisperKOOL warranty WE RECOMMEND THAT YOU DO NOT USE A GROUND FAULT INTERRUPTER GFI WITH THIS PRODUCT TEST THE UNIT PRIOR TO INSTALLATION To prepare it for testing before installation in wall e Remove unit from box e Place unit on tabletop e Plug in unit to electrical outlet e Plug in bottle sensor e Turn on to test Temperature differential should be 10 F across coils e Turn off after test e Remove bottle sensor Testing Unit Place the WhisperKOOL system on a tabletop to prepare it for installation and testing Plug system into a live electrical outlet and turn unit on The system may take up to 10 to 15 minutes before running cool Once the operation has been tested turn the unit off and u
34. tain limited warranty service 6 This limited warranty is void if the factory applied serial number has been altered or removed from the Product 7 Removing the rivets from the Product s unit housing without prior authorization from WhisperKOOL voids this limited warranty 8 The End User must first contact WhisperKOOL Customer Service by telephone at 1 800 343 9463 prior to attempting service on any Product still under the limited warranty else the limited warranty is voided 9 THE REPAIR OR REPLACEMENT OF THE PRODUCT AS PROVIDED UNDER THIS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF YOU THE END USER AS WELL AS ANYONE ELSE IN THE CHAIN OF TITLE OF THE PRODUCT DOES NOT START A NEW LIMITED WARRANTY TIME PERIOD AND IS IN LEIU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED WITH REGARD TO THE PRODUCT IN NO EVENT SHALL WHISPERKOOL BE LIABLE FOR INCIDENTAL CONSEQUENTIAL SPECIAL OR CONTINGENT DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED Some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you This limited warranty gives you specific legal rights and you may have other rights which vary from state to state 10 Failure of the End User to comply with all o
35. ust be pushed to activate the feature Refer to page 15 for complete listing of buttons and symbols Compressor and Condenser Fan Evaporator Cellar Pre Chill Button 3 5 Energy Saving Button 1 Hi Bottle Temp History amp Scroll Button 1 Energy Reduction Push to see the max stored temperature In programming mode use to browse the parameter codes or increase the display value Hold for 3 seconds to start Cellar Pre Chill Set Button View Set Point 1 Change Set Point 3 5 Gua e SET Down CPSM 10 15 Reset Hi amp Lo Button 3 5 0 i Low Bottle Temp History amp Scroll Button 1 Push to see the min stored temperature ALARM Pre Chill Display In programming mode use to browse the parameter codes or decrease the displayed value Display and modify set point In programming mode it selects a parameter confirms an opera tion Hold for 3 seconds when the min or max temperature is displayed to RESET Control ON OFF Button eTurns the Cooling Unit ON OFF Specifications Cellar Size 350 cu ft Dimensions 22 W x 10 25 H x 19 D Weight 50 Ibs AMPS starting running 175 35 OOO dBA Evaporator 59 Condenser 53 Installation Through the Wall ideally above a doorway Thermostat Advanced Digital Control Display Temp Delta 30 F temperature differential Warranty 2 year parts and labor 5 year compressor Page 3 INTRODUCTION The Slimlin
36. y all taxes duties levies or fees imposed on WhisperKOOL or Purchaser by any taxing authority related to Purchaser s order Payment for a WhisperKOOL Product must be made in lawful money of the United States of America in immediately available funds WhisperKOOL accepts all major credit cards WhisperKOOL may change payment terms for unfilled orders if in WhisperKOOL s reasonable opinion Purchaser s financial condition previous payment record or relationship with WhisperKOOL merits such change All Purchaser orders whether written or verbal are governed by these Terms and Conditions and are subject to acceptance by WhisperKOOL Any term or condition which may be included on any Purchaser s purchase order or in any form of communication whether verbal or in writing from any Purchaser to WhisperKOOL that is not identical with these Terms and Conditions is hereby expressly objected to and rejected by WhisperKOOL and shall NOT become a part of the contract of sale of any Product WhisperKOOLS failure to object to any such conflicting term and or condition of sale contained in any communication including a purchase order from a Purchaser shall not be considered as acceptance of such term and or condition or as a waiver of these Terms and Conditions The only language in which WhisperKOOL states these Terms and Conditions is English WhisperKOOL reserves the right in its sole discretion to change these Terms and Conditions at any time for an
37. y reason without notice WhisperKOOL shall not be liable to Purchaser for any delay of delivery of a Product caused by Force Majeure or any other cause beyond WhisperKOOL s control 2 WHISPERKOOL PRODUCT LIMITED WARRANTY A Two 2 Year Limited Warranty For the period of TWO 2 YEARS the Limited Warranty Period from the date of original sale of a Product by WhisperKOOL if a WhisperKOOL Product is found to be defective in material or workmanship after undergoing WhisperKOOL s customer service troubleshooting then subject to the WhisperKOOL Product Limited Warranty Limitations and Exclusions as well as the other Terms and Conditions stated herein WhisperKOOL will do the following as appropriate for the end user End User who has installed and is actually using the Product with regard to LABOR PARTS and FREIGHT 1 LABOR repair or replace at WhisperKOOLs sole option the Product at no charge to the End User and 2 PARTS supply at no charge to the End User new or rebuilt replacement parts for the Product in exchange for the return of defective parts and 3 FREIGHT cover normal ground freight charges for parts and in the event the Product is not repairable in the field cover normal ground freight charges within the continental United States for the repair or replacement of the Product B Five 5 Year Compressor Limited Warranty The two 2 year limited warranty period stated in Section 2 a above is extend
Download Pdf Manuals
Related Search