Manual WS 19 - Polar Audio
Contents
1. WIRELESS SERIES USER MANUAL FOR THE WS 19 SINGLE CHANNEL WIRELESS BELTPACK II iminairv CONTENTS 10 GENERAL DESCRIPTION 2 0 UNPACKING 3 0 INSTALLATION 40 FRONT PANEL 4 5 0 REAR PANEL 5 60 INTERNAL 5 7 0 CABLING Hart nn est 6 80 PARTY LINE TECHNICAL 7 90 GUADANTEE 14001 100 TECHNICAL SPECIFICATIONS User Manual WS 19 Issue 2 2002 ASL Intercom Utrecht Holland User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland 1 0 GENERAL DESCRIPTION The WS 19 is a portable single channel wireless user station housed in a strong Aluminum case On the front panel are a Volume listen level control a Talk and a Call button with LED indicators Special attention has been paid to the intelligibility of soeech By applying low noise high speed op amps a speech presence filter and a specially developed amplifier communication is very comfortable even in environments with a very high background noise level The unique ASL CALL system provides both a flashing red LED and a very distinctive and characteristic sound signal Smooth operation is guaranteed with the CALL button A momentary push makes the red LED flash whilst holding the button for two2. utilizes a current amplifier to amplify the microphone signal and place it on the common audio line where due to the constant line impedance situated in the power supply between XLR pin 3 and 1 a signal voltage is developed which can be further amplified and sent to the headphones This principle has three advantages the use of a single audio line allows several stations to talk and listen simultaneously due to the high bridging impedance offered by each station the number of stations line has no influence on the level of the communications signal power and audio to the intercom stations use the same cable The Call signal is also sent as a current on the audio line It develops a DC potential over the line impedance which will be sensed by each station and interpreted as a Call signal 9 0 WARRANTY is unit is warranted by ntercom to the original end user purchaser against defects in workmanship nd materi in it s man e for a period of one year from date of shipment to the end user Faults arising from misuse unauthorized modifications or accidents are not covered by this warranty If the unit is faulty it should be sent in it s original packing to the supplier or your local ASL dealer with shipping prepaid A note must be included stating the faults found and a copy of the original suppliers invoice THIS PRODUCT WAS DESIGNED DEVELOPED AND MANUFACTURED BY ASL Intercom UTRECHT HOLLAND h
3. eans that the beltpack has connection with the base station User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland SIDETONE ADJUSTMENT Turn down the OWN VOICE volume trimmer at the side panel of the beltpack clockwise Switch on the TALK function of the beltpack TALK button Talk in the microphone and listen to yur own voice you might hear a small delay the signal Now turn down the volume of your own voice by adjusting the SIDE TONE trimmer at the base station of the TX RX unit to which the beltpack is connected Adjust the trimmer so that the level of you own voice is as low as possible Now turn up the volume of your own voice by adjusting the OWN VOICE trimmer to a level that you like FULL DUPLEX AND HALF DUPLEX USE Although the system is designed to be used in full duplex use there is a possibility to use the system in half duple mode too Half duplex allows more than 1 beltpack on the same frequency and therefore on one TX RX unit of a base station Every beltpack will be able to listen to the base station but only one of the listening beltpacks can talk at a time and have a full duplex connection The other beltpacks will not be able to CALL or TALK In this mode it is usefull not to adjust the sidetone trimmer on the base station turr it fully counter clockwise Read the next chapter about communication modes carefully COMMUNICATION MODES This system is designed to offer a max
4. imum of 8 wireless full duplex beltpacks Each beltpack may be a single channel beltpack WS 19 or a dual channel beltpack WS 29 Each beltpack needs to be assigned to a unique channel On this channel the communication between the beltpack and the base station will take place If another base station is set to the same channel the communication will be garbled and will result in a none functioning connection The base station will automatically select the right mode for a WS 19 or WS 29 beltpack A WS 19 beltpack will always be connected to it own channel at the base station a WS 29 beltpack will be assigned to two channels on the base station FULL DUPLEX A connection of one WS 19 eg Channel 1 will be accomplished by selecting channel 1 on the beltpack and channel 1 on TX RX unit 1 of the base station The connection is a dedicated and full duplex connection The sidetone needs to be adjusted at the front of the base station and the user of the beltpack can adjust his own voice at the beltpack with the designated trimmer HALF DUPLEX A connection of several WS 19 beltpacks on eg Channel 1 to a TX RX unit of a base station also channel 1 selected is a half duplex connection This means that all the beltpacks can listen to the same TX RX unit of the base station Only one beltpack can TALK to the base station The beltpack that selects TALK mode will occupy the connection and the TALK function of all other listen
5. ing beltpacks is disabled The same for serding CALL signals only one beltpack may send a call signal but all of them will receive it There is one major drawback to half duplex mode this is due to the principle of the partyline concept In case of a very good adjusted sidetone trimmer at the base station this effect will be noticed When 2 or more beltpacks are using the same TX RX unit of a base station listening to the same signal and one of the beltpacks is talking to the base station the listening beltpack will not be able to hear the talking beltpack This effect is caused by the adjusted sidetone that prevents the microphone signal of a beltpack to be heard by him self and therefore also heard by other beltpacks on the same TX RX unit To solve this the sidetone trimmer of the TX RX unit should be turned fully counter clockwise This has one disadvantage too if a beltpack talks to the base he will hear his own voice in his headset with a delay of 24 mS The other listening beltpacks will not notice this delay By adjusting the OWN VOICE trimmer at the beltpack the effect can be made less User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland 2 16 Battery compartment This compartment will hold 6 penlight batteries of the AA type The supplied rechargeable NiMH batteries are the preferred types for the maximum duration Please take special attention in your choice of batterie
6. nob This knob adjusts the listen level for the headset 2 TALK button This push button activates the headset microphone the bright green LED 5 indicates if the microphone is switched on The beltpack must be in reach of the base station for the microphone to be switched on 3 CALL button This push button activates the call system A momentary push will send a call signal 5 4 to all stations connected to the intercom channel and the call LED 4 will start flashing Press and hold the button for 2 seconds will activate the call buzzer After the CALL button is released the LED s will continue to flash for further 2 seconds The beltpack must be in reach of the base station for sending or receiving a CALL signal User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland 5 0 SIDE PANEL CONNECTORS OWN VOICE trimmer This trimmer adjusts the level of your own voice as you hear it in your headset The operating area is between fully clockwise and minimum level Adjusting this signal does not affect the level of your voice as it is heard by other stations 7 TONE VOLUME This trimmer adjusts the level of the tones that the WS 19 produces in case ofa low battery Warning 8 BUZZER VOLUME trimmer This trimmer adjusts the volume of the internal buzzer which is located behind the front panel The buzzer is activated if you press the CALL button of the WS 19 3 ora ALL button of any other station on the channel
7. r or each minimum 400 ohms when in parallel The mic may be of the dynamic or electret type Pin assignments 1 Shield mic GND 2 mic 3 phones 4 phones User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland BELTPACK SETTINGS Don es BASE STATION SETTINGS The base station must be set up properly according to the user manual Give each TX RX unit of the base station its own channel by rotating the Channel select switch Try to avoid concurrent channels to be physically next to each other eg In a setting of two WS 400 try to set them in this order 2 4 6 8 1 3 5 7 If you use a WS 200 with only two beltpacks use channels 1 and 6 B Connect the base station to the partyline intercom or 4 wire system and make sure the interface mode switch at the back is set correctly C turn the sidetone trimmers counter clock wise Select with the channel select switch at the rear of the beltpack the channel to match the WS 200 or WS 400 setting Connect a headset to the beltpack and insert fully charged batteries When the beltpack is switched on then a single short tone should be heard and both led s on the front panel of the unit will flash for half a second This indicates that the beltpack is functioning okay If you press the CALL or TALK button the led s on the front panel will be lit and the corresponding TX RX unit of the base station will show a green ACTIVE led This m
8. s the WS 19 uses a high discharge current that the batteries need to sustain over the whole lifespan Batteries that can only supply a high current for a short time will be exhausted very quickly When the batteries reach the end of their capacity the beltpack will warn you with 4 short tones the interval of the tones will shorten when the batteries wear out l 1 17 Dip switch This dipswitch controls four functions of the WS 19 these 1 Talk function only momentary B Talk function disabled C Buzzer function disabled D Battery save mode The dipswitches are turned on by sliding them towards the side panel of the beltpack they are turned off when slid to the battery compartment 18 Service connector This connector is to be used only for factory service Do not connect anything to it and do not short circuit any of the pins User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland 8 0 PARTY LINE TECHNICAL CONCEPT 10 0 TECHNICAL SPECIFICATIONS WS 19 ASL s WIRELESS Series offers a complete two way full duplex communications system Users of the system are connected via a party line base stations with built in power supply beltpacks and power supplies are interconnected via standard microphone cable One wire is used as an audio line one as a power line and the screen of the cable functions as earth return Current drive is used for signal transfer Each station
9. seconds will activate the CALL sound signal The volume of the sound signal buzzer can be adjusted at the side panel 2 0 UNPACKING The shipping carton contains the parts listed below The WS 19 User manual 6 NiMh rechargeable Batteries If any are missing contact your dealer This WS 19 will form part of an existing or new intercom system in combination with a WS 200 or WS 400 base station There are no separate power connections the necessary DC voltages are derived from the internal batteries which can be charged by the internal battery charger Adjust the channel select switch to match the selected channel on the base station After switching on the unit with the power switch at the rear panel the unit should have User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland ASL has taken great care to ensure this product reaches you in flawless condition After unpacking the unit please inspect for any physical damage to the unit and retain the shipping carton and relevant packing materials for use should the unit need returning If any damage has occurred please notify your dealer immediately so that a written claim can be initiated Please also refer to the guarantee section of this manual 3 0 INSTALLATION contact with the base station To check this simply push the CALL or TALK button and the LED s should indicate a normal functioning beltpack 4 0 FRONT PANEL CONTROLS 1 VOLUME control k
10. to which the WS 19 is connected longer than 2 seconds 9 MIC GAIN The mic gain can be adjusted by a trimmer on the side panel To increase mic gain turn clockwise To decrease mic gain turn counterclockwise User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland el RE 10 Antenna This small antenna is chosen to be very flexible and non removable For optimum performance keep the antenna clear from obstacles 11 POWER on off switch This switch switches the unit on and off 12 CHANNEL SELECT switch With this switch the channel is selected on which the beltpack will communicate with the base station The selected channel must match the channel set at the base station 13 DC INPUT connector Apply a DC voltage of 12 Volts DC to this connector to charge the internal batteries The sleeve is negative and the inner contact is positive The LED indicator 14 will be lit red when the unit is charging the batteries and it will be lit green when the batteries are fully charged 14 Battery charger status LED This LED indicates the status of the battery charger The LED is lit red when the external adaptor is connected and the batteries are being charged The LED is green lit when the external adaptor is connected and the batteries are fully charged 10 111213 1415 15 HEADSET CONNECTOR An XLR 4 type connector for the connection of the headset This must have a can impedance of 200 ohms or greate
11. ttp www asl inter com 10 POWER CONSUMPTION current at 9 V DC 200 mA quiescent 280 mA signaling 450 mA at max output signaling MIC PREAMP mic impedance 200 ohms gain 40 dB 70 dB 6 dB at 5 kHz 200 Hz 12 kHz 3 dB presence filter frequency response V electret mic 9 V DC HEADPHONES DRIVER AMP max load 200 ohms max output level max output power 4 V rms 200 ohms 0 16 W rms each headset can BUZZER max SPL 90 dBA DIMENSIONS AND WEIGHT width 88 mm height 49 mm depth 141 mm weight 650 grams GENERAL SYSTEM SPECIFICATIONS dynamic range 80 dB Transceiver frequency 2400 2483 5 MHz Transmit Power 10 mW E I R P Number of channels 8 Channel separation 4 4 MHz supply voltage 7 2 V DC 4 2 V to 9 V Note OdBu 775 mV into open circuit ASL reserves the right to alter specifications without further notice User Manual WS 19 Issue 1 2002 ASL Intercom Utrecht Holland
Download Pdf Manuals
Related Search