380926_UM
Contents
1. 73 x 38mm 0 85 Ibs 880g 8 380926 4 1 07 07 Maximum Rated Input Limits Function Maximum Rated input Limits ACIDC Current 500mMA AC DC fused aape oaren nn ne ee Frequ ency 10 m TR E ORA EEE AE a Duty Cycle 1000 VACC 380926 4 1 07 07 Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment a six month limited warranty applies to sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department at 781 890 7440 ext 210 for authorization or visit our website www extech com for contact information A Return Authorization RA number must be issued before any product is returned to Extech The sender is responsible for shipping charges freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages Extech s total liability is limited to repair or replacement of the product The warranty set forth above is inclusive2. and no other warranty whether written or oral is expressed or implied Calibration and Repair Services Extech offers repair and calibration services for the products we sell Extech also provides NIST certification for most products Call the Customer Care Department for information on calibration services available for this product Extech recommends that annual calibrations be performed to verify meter performance and accuracy Support line 781 890 7440 Technical support Extension 200 E mail support extech com Repair amp Returns Extension 210 E mail repair extech com Product specifications subject to change without notice For the latest version of this User s Guide Software updates and other up to the minute product information visit our website www extech com Extech Instruments Corporation 285 Bear Hill Rd Waltham MA 02451 Copyright 2007 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form 10 380926 4 1 07 07
3. User s Manual EXTECH INSTRUMENTS 2000A Auto Ranging True RMS Clamp DMM MODEL 380926 INTRODUCTION Congratulations on your purchase of Extech s 380926 Clamp meter Digital MultiMeter This meter can measure to 2000A through the clamp and also measure to 400mA through the test leads With Capacitance Diode and Duty Cycle measurements this meter provides the user with a full featured multimeter combined with the high amperage current clamp This meter is shipped fully tested and calibrated and with proper use will provide years of reliable service SAFETY Safety Symbols oP e This symbol adjacent to another symbol or terminal indicates the user must refer to the manual for further information This symbol adjacent to a terminal indicates that under normal use hazardous voltages may be present Double insulation WARNING This indicates that a potentially hazardous condition which if not avoided could result in death or serious injury CAUTION This indicates that a potentially hazardous condition which if not avoided could result in injury or damage to the meter Reply to request Safety Precautions 1 WARNING Improper use of this meter can cause damage shock injury or death Read and understand this user s manual before operating the meter Make sure any covers or battery doors are properly closed and secured Always remove the test leads before replacin
4. e test lead tips to the diode A typical diode forward voltage drop will indicate 0 3 to 0 7V The reverse drop will indicate OL indicating high impedance Proper diode check should include both forward and reverse tests N ji BLACK BLACK j FORWARD TEST REVERSE TEST Frequency Measurement 1 Set the Function switch to the Hz position 2 Press the FUNC key until the Hz symbol appears on the LCD 3 Insert the black test lead to the COM input jack and the red test lead to the Hz input jack 4 Connect the tips of the test leads to the device to be measured see diagram 5 Read the frequency value in Hz on the LCD Duty Cycle Measurements Follow the steps as for Frequency measurements with the following exception Press the Hz key until the symbol appears on the display Capacitance Measurement 1 Set the Function switch to the 4 position 2 Press the FUNC key until the nF symbol appears on the LCD 3 Insert the black test lead to the COM input jack and the red test lead to the red input terminal 4 Connect the tips of the test leads to the device to be measured see diagram 5 Read the capacitance value on the display NOTE When making very low capacitance measurements use the REL function to zero any stray capacitance 6 380926 4 1 07 07 Automatic Manual Range Selections The meter defaults to the autoranging mode when turned on NUJKS will appear in the display To select ma
5. g the battery or fuses Inspect the condition of the test leads and the meter itself for any damage before operating the meter Repair or replace any damage before use Do not exceed the maximum rated input limits Use great care when making measurements if the voltages are greater than 25VAC rms or 35VDC These voltages are considered a shock hazard Always discharge capacitors and remove power from the device under test before performing Capacitance Diode Resistance or Continuity tests Remove the battery from the meter if the meter is to be stored for long periods 2 380926 4 1 07 07 METER DESCRIPTION Front panel CL oe hy Keypad LCD display Input jacks Current Sense Jaws Function switch Note The tilt stand and battery compartment door are located on the rear of the meter Symbols AC current or Voltage DC current or Voltage Continuity Display hold Relative Auto range Diode Display Backlight millivolt volt voltage ohm kilohm megohm resistance percent duty cycle microamps milliamps amps current hertz kilohertz frequency nanofarad microfarad capacitance 380926 4 1 07 07 OPERATING INSTRUCTIONS Current Measurements using the Clamp DC AC WARNING Make sure that the test leads are disconnected from the meter s terminals before making current measurements with the clamp jaw WARNING For safety use the rubber input terminal cover
6. lead to the COM input jack and the red test lead into the V input jack Connect the test leads in PARALLEL with the circuit to be measured see diagrams Read the measured value from the LCD display A Voltage Voltage Resistance Measurements CAUTION Before taking any in circuit resistance measurements remove power from the circuit under test and discharge all capacitors 1 2 3 4 5 Set the Function switch to the Q position Press the FUNC key until the ohms symbol appears on LCD Insert the black test lead to the COM input jack and the red test lead to the Q input jack Connect test leads to the device under test see diagram Read the measured value from the LCD display Resistance Continuity Test N 2 Set the Function switch to the e position Press the FUNC key until the Q and s symbols appear on the display Insert the black test lead to the COM input jack and the red test lead to the Q input jack Connect the test lead tips to the device to be measured refer to diagram for resistance measurements above Read the measured value from the LCD display If the resistance is lt 10Q approx an audible signal will be heard 5 380926 4 1 07 07 Diode Test 1 Set the Function switch to the diode position Press the FUNC key until the t symbol appears on the LCD 3 Insert the black test lead to the COM input jack and the red test lead to the Pt input jack 4 Connect th
7. nual ranging press the RANGE key Momentary presses of the RANGE key will step through the ranges To return to the Auto Range mode press and hold the RANGE key for 2 seconds Relative Reading Measurements Press the REL key to enter the relative mode RE will appear in the display In the relative mode the meter stores the reading that was on the display at the time of the REL key is pressed and displays the difference between the measured value and the stored value Press the REL key to return to normal mode Data Hold Backlight key Press the HOLD key momentarily to freeze the present reading on the LCD will appear in the display Press HOLD again to return to normal operation Backlight Press and hold the Hold key for 2 seconds to activate the backlighting The backlight will automatically turn off to conserve energy after approx 12 seconds MAINTENANCE Battery Replacement When the low battery symbol appears on the LCD replace the meter s 9V battery 1 Remove power to the meter and remove test leads from meter 2 Remove the Phillips head screw back of meter and open the battery compartment 3 Remove and replace the 9V battery 4 Replace the compartment cover and rear screw Fuse Replacement NOTE Fuse Rating 500mA 5mm x 20mm diameter 1 The meter is provided with one overload protect 500mA fuse for current measurements direct input NOT clamp measurements 2 To replace the fuse open the meter case b
8. when measuring current using the Clamp Set the Function switch to 2000A position Press the FUNC key to select AC or DC current For DC current measurements push amp hold the DCA ZERO button until the reading indicates zero Press the trigger to open jaw Fully enclose the conductor to be measured see diagram The clamp meter will automatically select the proper range Auto Range To select the range manually press the RANGE button before pressing DCA ZERO button INCORRECT Read the measured value from the eee CORRECT LCD display conductor in jaws One conductor in jaws NOTE If the DCA zero button is used to zero the meter the clamp meter remains in the auto range mode If the REL button is used the clamp meter will be placed in the manual range mode Current Measurements using the Test Leads DC AC l 2 Press the FUNC key to select AC or DC 3 Connect the black test lead to the COM terminal and the red test lead to the mA WPA input jack 4 Break the circuit under test put the meter in series with circuit under test refer to diagram 5 Read the measured value from the LCD display NOTE The maximum reading for direct input current is 240mA AC DC Set the Function switch to the mA or pA position pA and mA Current 4 380926 4 1 07 07 Voltage Measurements DC AC 1 2 3 Set the Function Switch to the V position Press the FUNC key to select AC or DC Insert the black test
9. y removing the battery cover and battery and then the four screws holding the rear case 3 The fuse is located on the Main PCB 4 Replace fuse and secure meter case 7 380926 4 1 07 07 SPECIFICATIONS Clamp on H 0 3d AC Voltage 1 2 5d 45Hz to 1KHz True RMS Input Impedance 10Mohms 0 5 2d Input Impedance 1 0 2d 10Mohms 1 0 5d 2 0 2d H 5 5d AC DC Current 1 2 5d 45Hz to 1KHz Direct Input Frequency 1 5d Capacitance 3 5d Accuracy stated after a relative REL zero performed Duty Cycle 1t099 01 0 45d S Continuity Audible tone lt 10 ohms aT Open circuit voltage 0 5V approximately Conductor Size DC Voltage Resistance 60mm 2 36 maximum Measurement parameters Current Sensor Zero adjust Diode Test Battery type Range Selection Display Overload Indication Power Consumption Low Battery Indication Sampling rate Standards Operating Temperature Humidity Dimensions Weight ACA en ACV DCV Resistance Diode Frequency Capacitance Duty Cycle Continuity Hall Effect Automatic except for DCA Push button Test current of 0 6mA typical Open circuit voltage lt 1 6V DC typical 9V NEDA 1604 Auto or manual 0 6 15mm 5000 Count Backlit LCD OL 5mA approx Battery icon appears on LCD 1 reading every 0 35 seconds approx CE IEC 1010 1 CAT IV 600V 32 to 122 F 0 C to 50 C lt 80 10 x 2 9 x 1 5 255 x
Download Pdf Manuals
Related Search
380926_UM 380926 multimeter 2000a