PCH2600 User`s Manual
Contents
1. The figure indicates 0001 the physical ID number is 1 IDO IDI ID2 ID3 ON The figure indicates 0010 the physical ID number is 2 ON ON IDO IDI ID2 ID3 The figure indicates 0011 the physical ID number is 3 Physical ID setting OFF 0 OFF 0 0 0 OFF 0 ON 1 1 1 ON 1 OFF 0 2 2 ON 1 ON 1 3 9 6 PCH2600 Fiber Optic Communication Card V6 004 Chapter 3 Optical Fiber Communication 3 1 Optical Fiber Communication Principle Fiber optic Communication is a method of transmitting information from one place to another by sending pulses of light through an optical fiber The light forms an electromagnetic carrier wave that is modulated to carry information The process of communicating using fiber optics involves the following basic steps Creating the optical signal involving the use of a transmitter relaying the signal along the fiber ensuring that the signal does not become too distorted or weak receiving the optical signal and converting it into an electrical signal Advantages of Fiber optic Communication Frequency band is wide and the communication capacity is large gt Low loss long distance relay With anti electromagnetic interference gt Nocrosstalk security is good gt High quality communication The Application of Fiber optic Communication Card Fiber optic communication system Fiber optic access network Fiber optic data t2. PCH2600 Fiber Optic Communication Card V6 004 PCH2600 User s Manual 9 Beijing ART Technology Development Co Ltd PCH2600 Fiber Optic Communication Card V6 004 Contents S70 2g Dp Chapter 1 Overview is deserere ded x Ed n fan ER EUR EUR UC UR FER EUR ER e E ed ree Eee E ER ERA Chapter 2 Components Layout Diagram and a Brief Description renn 2 1 The Main Component Layout Diagram eese anena aain tn 2 2 Board Layer and Physical ID Selection uie rr teer i ede e e ir terrd eet Chapter 3 Optical Fiber Communication ae 3 1 Optical Fiber Communication Principle asenin The Application of Fiber optic Communication Card ee Chapter 4 Notes Calibration and Warranty Policy rare eene nennen eene enne e etri nnne ennt enne Products Rapid Installation and Self check Rapid Installation s SEE vise HM Delete Wrong 094 ELLE M S PCH2600 Fiber Optic Communication Card V6 004 Chapter Overview PCH2600 is a fiber optic communication card based on PC104 bus can connect with PC104 interface receive and send data via optical fiber Unpacking Checklist Check the shipping carton for any damage If the shipping carton and contents are damaged notify the local dealer or sales for a replacement Retain the shipping carton and packing materia
3. e of properly licensed software with our systems ART does not condone the use of pirated software and will not service systems using such software ART will not be held legally responsible for products shipped with unlicensed software installed by the user 3 Our repair service is not covered by ART s guarantee in the following situations Damage caused by not following instructions in the User s Manual Damage caused by carelessness on the user s part during product transportation Damage caused by unsuitable storage environments i e high temperatures high humidity or volatile chemicals Damage from improper repair by unauthorized ART technicians gt Products with altered and or damaged serial numbers are not entitled to our service 4 Customers are responsible for shipping costs to transport damaged products to our company or sales office 5 To ensure the speed and quality of product repair please download an RMA application form from our company website PCH2600 Fiber Optic Communication Card V6 004 Products Rapid Installation and Self check Rapid Installation Product driven procedure is the operating system adaptive installation mode After inserting the disc you can select the appropriate board type on the pop up interface click the button driver installation or select CD ROM drive in Resource Explorer locate the product catalog and enter into the APP folder and implement Setup exe file After the ins
4. iber Optic Communication Card V6 004 Chapter 2 Components Layout Diagram and a Brief Description 2 1 The Main Component Layout Diagram E hh Jd A L 2 pw mr Cycione 0 TEx PS bg EP 2 ICO gt N vo o9 sek e ne gh x gt ao EME f O TIENI IRX TX CONNECT Optical fiber communication interfaces including TX transmitter and RX receiver 2 2 Physical ID Selection DIDI set the physical ID when install multiple PC104 boards the board is inserted in the PC104 interface is the bottom board the layer number is 0 the boards up from the bottom to the up the layer number is 1 2 3 Then the users can easily distinguish and access each card by the hardware configuration and software programming The switch No 1 2 3 4 correspond to IDO ID1 ID2 ID3 ID2 ID3 are reserved Each bit is the binary switches dial to ON that means the 1 the switch to the other side means 0 When the board left the factory the test software usually BUY ONLINE at art control com englishs or CALL 86 0 10 62991792 CN PCH2600 Fiber Optic Communication Card V6 004 uses the logical ID to management device so the physical ID is invalid If you want to use multiple devices in a system we had better to use physical ID DIDI IDO IDI ID2 ID3 ON The figure indicates 0000 the physical ID number is 0 ON ON IDO IDI ID2 ID3
5. l for inspection by the dealer Check for the following items in the package If there are any missing items contact your local dealer or sales PCH2600 Data Acquisition Board gt ART Disk a user s manual pdf b drive c catalog gt Warranty Card FEATURES Transmission Speed 200Mbps Transmission Distance up to 30Km Support point to point transmission mode Support full duplex transmission Receive transmit independently Bus Type PC104 bus FIFO 4K byte 32 bit 2K receive transmit independently Data Read Write program query DMA mode Support Windows 2000 XP Vista OS Prevent signal interference VV VV VV VV ON ON Specification Parameters Hardware gt Bus Type PC104 bus gt FIFO 4K byte 32 bit gt Data Read Write program query DMA mode gt One PC can connect with four PCH2600 Fiber Optic Interface Fiber Optic Interface SC card Fiber Optic Jumper SC type jumper Transmission Speed 200Mbps Transmission Distance up to 30Km Support point to point transmission mode Support full duplex transmission VV VV VV V FIFO 2K receive transmit independently BUY ONLINE at art control com englishs or CALL 86 0 10 62991792 CN 3 PCH2600 Fiber Optic Communication Card V6 004 Software gt Support Windows 2000 XP Vista OS Working Environment gt Operating Temperature Range 0 C 50 C gt Relative Humidity 5 95 RH gt Storage Temperature Range 20 C 70 C 4 PCH2600 F
6. ransmission Fiber optic CATV Local Area Network LAN Test equipment Fiber optic sensor VVVVV Vv N PCH2600 Fiber Optic Communication Card V6 004 Chapter 4 Notes Calibration and Warranty Policy 4 1 Notes In our products packing user can find a user manual PCH2600 module and a quality guarantee card Users must keep quality guarantee card carefully if the products have some problems and need repairing please send products together with quality guarantee card to ART we will provide good after sale service and solve the problem as quickly as we can When using PCH2600 in order to prevent the IC chip from electrostatic harm please do not touch IC chip in the front panel of PCH2600module 4 2 Warranty Policy Thank you for choosing ART To understand your rights and enjoy all the after sales services we offer please read the following carefully 1 Before using ART s products please read the user manual and follow the instructions exactly When sending in damaged products for repair please attach an RMA application form which can be downloaded from www art control com 2 All ART products come with a limited two year warranty The warranty period starts on the day the product is shipped from ART s factory gt For products containing storage devices hard drives flash cards etc please back up your data before sending them for repair ART is not responsible for any loss of data gt Please ensure the us
7. tallation pop up CD ROM shut off your computer insert the PCI card If it is a USB product it can be directly inserted into the device When the system prompts that it finds a new hardware you do not specify a drive path the operating system can automatically look up it from the system directory and then you can complete the installation Self check At this moment there should be installation information of the installed device in the Device Manager when the device does not work you can check this item Open Start gt Programs gt ART Demonstration Monitoring and Control System gt Corresponding Board gt Advanced Testing Presentation System the program is a standard testing procedure Based on the specification of Pin definition connect the signal acquisition data and test whether AD is normal or not Connect the input pins to the corresponding output pins and use the testing procedure to test whether the switch is normal or not Delete Wrong Installation When you select the wrong drive or viruses lead to driver error you can carry out the following operations In Resource Explorer open CD ROM drive run Others gt SUPPORT gt PCI bat procedures and delete the hardware information that relevant to our boards and then carry out the process of section I all over again we can complete the new installation
Download Pdf Manuals
Related Search