Raven Series Standalone Media Converters
Contents
1. 18 Transition Networks Inc 10900 Red Circle Drive Minnetonka MN 55343 USA Tel 952 942 7600 Or 800 526 9267 Fax 952 941 2322 Info transition com http www transition com MILAN BY an TRANSITION2. Fiber LK ACT FDX COL The following table provides description of the LED status and their meanings Ees Power on Green 100Mbps UTP Speed OFF 10 Mbps UTP Speed Green The unit is linking with it s link partner LK ACT Blink The unit is transmitting or receiving packets UTE ee from UTP devices Off No device attached The unit is linking with it s link partner LK ACT The unit is transmitting or receiving packets Fiber from FX devices Off No device attached Orange The UTP port is operating in full duplex mode FDX COL Blinks Collision of Packets occurs in the port UTP for Half duplex mode or no device attached The fiber port is operating in full duplex mode FDX COL Collision of Packets occurs in the port Fiber a Half duplex mode or no device attached Table 2 1 Fast Fiber Converter LED indicator statuses and meaning DIP Switches The DIP switches are used to configure operation mode for LLF Link Loss Forwarding and operation mode for the UTP and Fiber ports The default value of each DIP switch is OFF UTP 100Mbps Full Duplex mode UTP Auto Negotiation Fiber in Half Duplex Fiber in Full Duplex 7 Bi Directional LinkSentry Enable LLF Disable Pure converter mode Switch Converter mode Table 2 2 Fast Fiber Converter DIP Switch statuses and meaning Link Loss Forwarding LLF Enabling LLF allows UTP link failures to be reported to the fiber side or Fiber link failures to be rep
3. or purchaser and is not assignable Transition Networks makes no express or implied warranties including but not limited to any implied warranty of merchantability or fitness for a particular purpose except as expressly set forth in this warranty In no event shall Transition Networks be liable for incidental or consequential damages costs or expenses arising out of or in connection with the performance of the product delivered hereunder Transition Networks will in no case cover damages arising out of the product being used in a negligent fashion or manner Trademarks The MiLAN logo and Transition Networks trademarks are registered trademarks of Transition Networks in the United States and or other countries To Contact Transition Networks For prompt response when calling for service information have the following information ready Product serial number and revision Date of purchase Vendor or place of purchase You can reach Transition Networks technical support at E mail techsupport transition com Transition Networks 10900 Red Circle Drive Minnetonka MN 55344 United States of America Telephone 1 800 526 9267 Fax 1 952 941 2322 http www milan com info Transition com Copyright 2006 Transition Networks FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasona
4. MILAN BY TRANSITION Raven Series Standalone Media Converters MIL RC3112 10 100BASE TX 100BASE FX ST MMF MIL RC3113 10 100BASE TX 100BASE FX SC MMF MIL RC3113 XX 10 100BASE TX 100BASE FX SC SMF MIL RC31W13 10 100BASE TX 100BASE FX SC SMF TX 1310nm WDM MIL RC31W15 10 100BASE TX 100BASE FX SC SMF TX 1550nm WDM USER GUIDE Regulatory Approval FCC Class A UL 1950 CSA C22 2 No 950 EN60950 CE EN55022 Class A EN55024 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference Causing Equipment Regulations Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada European Notice Products_with the CE Marking comply with both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community Compliance with these directives imply conformity to the following European Norms EN55022 CISPR 22 Radio Frequency Interference EN61000 X Electromagnetic Immunity EN60950 IEC950 Product Safety One Year Limited Warranty Transition Networks warrants to the original consumer or purchaser that each of it s products and all components thereof will be free from defects in material and or workmanship for a period of one years from the original factory shipment date Any warranty hereunder is extended to the original consumer
5. ble protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures a Reorient or relocate the receiving antenna a Increase the separation between the equipment and receiver a Connect the equipment into an outlet on a circuit different from that to which the receiver is connected a Consult the dealer or an experienced radio TV technician for help CE Mark Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Table of Contents 1 Introduction Features Package Contents 2 Hardware Description Front Panel Ports LED Indicators DIP Switches Rear Panel 3 Installation Converter Module Rackmount Chassis Cabling 4 Troubleshooting 5 Optical Fiber Specifications 6 Technical Specifications 1 Introduction The Raven Series Fast Fiber Advanced Media amp Rate Converters are standalo
6. echnical Specifications This section provides the technical specifications of the Raven Series Fast Fiber Advanced Media amp Rate Converter products IEEE802 3 10BASE T Standard IEEE802 3u 100BASE TX 100BASE FX IEEE802 3x Flow Control and Back pressure Fiber Duplex ST SC MT Ru Simplex SC WDM single mode Connector RJ 45 Socket CAT 3 5 10 100Mbps Twisted Pair cable Auto MDI MDI X and Auto Negotiation Function Support Sn Store and Forward architecture Fiber Core Multi Mode 62 5 125um 50 125um Single Mode 8 125um 9 125um Wavelength 850nm Multi mode 1310nm Single mode 1550nm WDM TX 1310nm WDM RX Fiber Distance Multi Mode Fiber 2KM Single Mode Fiber 30 KM WDM Single Mode 20KM Transparent 64 to 1518 Bytes for Non VLAN Ethernet packet packet 17 Fiber parameters Link Loss Forward DIP Switch EMI amp safety UTP Fiber If UTP port link is down then the converter will force the fiber port to link down Fiber UTP If Fiber port link is down then the converter will force the UTP port to link down DIP Switch 1 UTP Auto Nego 100Mbps Full Duplex mode DIP Switch 2 Fiber Full Half Duplex DIP Switch 3 LLF Link Loss Forwarding Disable Enable DIP Switch 4 Switch Converter Pure converter mode Module Power TX 100Mbps LK Act FDX COL Fiber LK Act FDX COL Stand alone external adapter DC9V 0 7A Module 119mm x 85mm x 26mm FCC Class A CE UL CUL
7. ne units that can be used alone or in a 10 slot rackmount chassis to connect networks with 10 100Base TX and 100Base FX cabling These advanced media amp rate converters extend the cabling distance of 100Base FX network up to 2 kilometers for multi mode fiber or 30 kilometers for single mode fiber Figure 1 1 The Raven Series Fast Fiber Media Converter Module Each converter is available with one SC ST multi mode fiber connector or SC single mode fiber connector plus one Ethernet Ru 45 port Auto MDI MDIX for your 100Base TX copper cable connection DIP switches allow for setting the operation mode for UTP Fiber and link loss forwarding function The WDM Converter converts signals between 10 100Base TX and 100Base FX cabling and incorporates WDM technology that allows a grouping of different services on existing optical fibers inside The WDM technology makes transmit TX and receive RX lines onto a 1 single fiber which reduces half of the cabling cost WDM converters must be installed in pairs with one 1310nm wavelength converter at one end of the single fiber cable and one 1550nm wavelength converter at the other end The fiber cabling can extend the connectivity distance up to 20 kilometers Features Fast Fiber Converter Modules Comply with IEEE 802 3 802 3u and 802 3x standards Convert between UTP cabling and Fiber optic cabling One RJ 45 connector Auto MDI MDIX for UTP port Support 10 100 Mbp
8. network 5 Optical Fiber Specifications This section provides the optical fiber specifications of the Raven Series Fast Fiber Advanced Media amp Rate Converter products Avg Wavelength Avg Lunch nm Power dB Module Name Sensitivity dB Converter SC 1310 nm 18 dB 30 a r n om ue fe Converter SC Single 1310 nm 20 dB 32 Mode dB dB Modular Fast Fiber 1310 nm 15 dB 34 dB Converter SC 30k dB dB m Modular Fast Fiber 1310 nm 5 dB 35 Converter SC 60km Modular Fast Fiber 1310 or 1550 8 dB Converter WDM 20km Avg Power Module Name Loss Budget Max FDX Fiber Fiber Size Dist K ae istance Km um Modular Fast Fiber 62 5 125 12 dBm 2 Km Converter SC 50 125 Modular Fast Fiber 9 125 Converter SC Single 12 dBm 15 Km 8 125 15 Modular Fast Fiber 9 125 23 dBm Modular Fast Fiber dBm 20 Km 8 125 Converter WDM 20km Optical Specifications of Transceivers 1310 nm Transmitter Output Center Wavelength 1261 1360 nm Single Mode Receiver Wavelength of Operation 1100 1600 nm Optical Transmit Power Min 15 dBm Max 8 dBm Sensitivity Min Max 31 dBm 1550 nm Transmitter Output Center Wavelength 1510 1590 nm Single Mode Receiver Wavelength of Operation 1100 1600 nm Optical Transmit Power Min 15 dBm Max 8 dBm Sensitivity Min Max 31 dBm 16 6 T
9. orted to the UTP side Pure Converter mode DIP Switch 4 When pure converter mode is enabling on it operates with the minimum latency The transmission flow does not wait until entire frame is ready but instead it forwards the received data immediately after the data being received And TP port should be forced at 100M in this application When DIP Switch is in Switch Converter mode off the converter function is same as Switch Hub Note Data errors may occur if DIP Switch settings are changed while the UTP or Fiber ports are transmitting or receiving data Rear Panel The rear panel of the converter contains a power socket This power socket accepts DC9V voltage and minimum 0 7A supplied current DC IN o Ore Figure 2 3 Rear Panel for Raven Series Fast Fiber Converters 10 3 Installation Converter Module A Remove the blank bracket by rotating thumbscrew counterclockwise Do not discard the blank bracket B Open the rackmount ear kit Each kit contains two rackmount ear pieces with thumbscrews and four screws C Attach one rackmount ear on each side of the converter using a screwdriver Ave MOUND e LWACT i a RX I 4 Fast Fiber G op 4 Converter Fox A Mn 9 LK ACT Multimode Figure 3 1 Attach mounting brackets with screws 11 Rackmount Chassis A Insert the modular converter module into the guides of the conversion system chassis by sliding it smoothly
10. s Auto negotiation for UTP port Fiber cabling connectivity up to 30Km Uses store and forward switching to separate two collision domains One fiber connector SC SC single mode fiber ST MT RJ VF 45 for 100Base FX 4DIP switches to set the operation mode and Link Loss Forwarding function LEDs for ach port 100 Link Activity Full Collision LEDs for each unit Power External DC power adapter 9V 0 7A Two types of module Stand alone and mounted in converter chassis FCC Class A CE UL and CUL Mark certification WDM Converter Modules Comply with IEEE 802 3 802 3u and 802 3x standards Convert between UTP cabling and Fiber optic cabling WDM Wavelength Division Multiplexing supports single fiber converter transporting Bi direction full duplex signal over a single fiber simultaneously One RJ 45 connector Auto MDI MDIX for UTP port Support 10 100 Mbps Auto negotiation for UTP port One Single SC Style Single Mode Connector for 100 Base FX fiber cable Fiber cabling connectivity up to 60Km Uses store and forward switching to separate two collision domains 4DIP switches to set the operation mode and Link Loss Forwarding function LEDs for each port 100 Link Activity Full Collision LEDs for each unit Power External DC power adapter 9V 0 7A FCC Class A CE UL and CUL Mark certification Package Contents Unpack the contents of the package and verify them against the appropriate checkli
11. st below Fast Fiber Converter AC DC Power Supply Users Guide Rackmount Kit If any item is missing or damaged please contact your local dealer for service 2 Hardware Description Front Panel The Front Panel of the WDM Converter consists of one Single SC style single mode connector one RJ 45 Port Auto MDI MDIX and 6 LED Indicators UTP 100 LK ACT FDX COL Fiber LK ACT FDX COL and PWR Auto MDI MDIX 1310 nm 100 m o c LKJAGT WDM Fiber Converter rancor Single Mode Figure 2 1 Front Panel for Raven Series Fast Fiber WDM Converters The Front Panel of the Fast Fiber Converter consists of one RJ 45 Port Auto MDI MDIX 6 LED Indicators UTP 100 LK ACT FDX Fiber LK ACT FDX and PWR and one fiber 100Base FX Port Multi Mode Figure 2 2 Front Panel for Raven Series Fast Fiber Converters Ports E RJ 45 Port Auto MDI MDIX The Ethernet RJ 45 will auto sense for 10Base T or 100Base TX connections Auto MDI MDIX means that you can connect to another Switch or workstation without changing non crossover or crossover cabling m Fast Fiber Port The Fast Fiber port is for 100 Base FX connections SC multi mode SC single mode ST MT RJ and VF 45 connections are available LED Indicators There are 6 diagnostic LEDs located on the front panel of WDM Converter They provide real time information of system and optional status The indicator includes Power UTP 100 LK ACT FDX COL
12. until it stops Press firmly until the power plug in the chassis plugs into the modular converter module receptacle Figure 3 2 Installing Gigabit Fiber Converter into Chassis B Gently push the thumbscrews in and turn clockwise to tighten Do not over tighten the thumbscrews 12 Cabling Use four twisted pair Category 5 cabling for RJ 45 port connections The cable between the converter and the link partner switch hub workstation etc must be less than 100 meters 328 ft long Fiber segments using single mode connector type connections must use 8 125 or 9 125 um single mode fiber cable Two devices may be connected up to 10 Kilometers in full duplex operation For half duplex operation the recommended maximum distance is 412 meters 1 352 ft Fiber segments using multi mode connector type connections must use 50 or 62 5 125 um multi mode fiber cable Two devices may be connected up to 550 meters 13 4 Troubleshooting This section is intended to help solve some common problems encountered while using the Raven Series Fast Fiber Advanced Media amp Rate Converter products m Verify that the correct power adapter DC 9V 0 7A is in use Power adapters with DC output higher than 9V will seriously damage the converter modules m Verify the DIP switch configuration is set to the same operational mode as the link partner m Ensure the proper UTP and Fiber cables have been selected to construct the
Download Pdf Manuals
Related Search