User Manual
Contents
1. The navigation light should be installed according to IMO regulations and other relevant rules and regulations for electrical installations onboard ships Consider the difference in material between the navigation light seawater resistant brass and the wall mast it is to be installed on Use galvanic isolators whenever there is a risk of corrosion e Fix navigation light to mast ships structure using 2x M10 bolts not supplied Use acid resistant screws bolts Tight firmly max 25 Nm e Open junction box install and secure electrical cable The cable must be clamped near up to the navigation light according to relevant rules and regulations for elec trical installations onboard ships e Connect electrical wires Max 2 5mm Strip length 8mm Tightening force 0 6 0 8nm Connect ground wire to M5 earth screw in junction box e Screw on junction box lid Max tightening force 5 Nm Make sure that gasket is centered and covering the whole perimeter e External bonding conductor Connect bonding wire to point shown in illustration above M8 screw For mounting and screening of side navigation lights see illustration next page TEF 2870 Ex NAVIGATION LIGHT USER MANUAL B SCREENING DATA FOR SIDE N Lo ij x ij DEE an p i Wa d NOTE All measurements in millimeters A2. www tranberg com Tranberg Systems Hjulmagervej 15C 7100 Vejle Denmark Tel 45 75 85 83 80 E mail mail tranbergsystems com www tranbergsystems com Brass lens of through coloured glass According to installed light bulb Max 230V 40W for 24V versions 65W for 115 230V versions P28S 40 65 Watt IP56 M20 Ex nR 6 5 14mm Ex zone 2 and safe area x II3G Ex nR IIC Ge T5 52 C to 50 C EC type examination MED B 6820 issued by DNV Product quality system MED D 1497 issued by DNV PRESAFE 14 ATEX 5436X IECEx PRE 14 0055X Special conditions Resistance to impact is tested with reduced values according to IEC 60079 0 2011 26 4 2 low risk of mechanical damage Directive 96 98 EC Annex A 1 item No A 1 6 1 and Annex B module B COLREG 72 as amended Annex 14 IMO Res A 694 17 IMO Res MSC 253 83 IEC 60079 15 2010 IEC 60079 0 201 1 TRANBERG
3. our sole responsibility that the Products Navigation Lights with Type designations TEF 2840 TEF 2850 TEF 2870 TEF 2898 application of Council Directive 96 98 EC of 20 December 1996 on Marine Equipment as amended by Directive 2009 26 EC issued as Forskrift om Skipsutstyr by the Norwegian Maritime Directorate to which this Declaration relates to conforms to the following Regulations Standards Annex A 1 item No A 1 6 1 and Annex B Module B in the Directive COLREG 72 as amended Annex 1 14 IMO Res A 694 17 and IMO Res MSC 253 83 For assessment see e EC Type Examination Module B Certificate MED B 7473 issued by DNV e Product Quality System Module D Certificate MED D 1497 issued by DNV This Declaration is issued according to the provisions of European Council Directive 98 98 EC on Marine Equipment as amended by Directive 2009 26 EC Stavanger Date 2011 05 02 Updated 2011 05 12 Updated 2015 02 26 Cre En yazer Torstein Rysstad Discipline Lead Electronics P O Box 8033 N 4068 Stavanger Norway P O Box 8033 N 4068 Stavanger Norway Material Input voltage Light source Lamp base Power comsumption Ingress protection Cable gland Area of use Ex classification Operating temperature Certificate No Compliance standards Tranberg AS P O Box 8033 N 4068 Stavanger Norway Tel 47 51 57 89 00 Fax 47 51 57 89 50 E mail info tranberg com
4. TEF 2870 Ex NAVIGATION LIGHT USER MANUAL IMPORTANT Read this instruction carefully before installing the product ees DO NOT OPEN MAINTAIN OR SERVICE IN AN AREA WHERE AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT TRANBERG Tranberg AS PO Box 8033 N 4068 Stavanger Norway Tel 47 51 57 89 00 Fax 47 51 57 89 50 E mail info tranberg com www tranberg com Tranberg Systems Hjulmagervej 15C 7100 Vejle Denmark Tel 45 75 85 83 80 E mail mail tranbergsystems com www tranbergsystems com TUM 4834 REV D 13 04 2015 TEF 2870Ex NAVIGATION LIGHT USER MANUAL INTRODUCTION Thank you for purchasing this product For installation maintenance and assurance of a long life of this product please follow this manual CONTENT IN BOX The product is fully assembled and ready for installation SAFETY PRECAUTIONS Note that changes made to the product and or installation of components which do not conform to the approval may be a safety violation The manufacturer will in no circumstance be held responsible for such activity For your health and safety always use safety gear suited for the task Be certain to follow codes regulations and or specific procedures that are related to the installation IMPORTANT INFORMATION The navigation lights are supplied with galvanic isolators These should be placed between the navigation light and the wall thus preventing corrosion to either There sh
5. ll tolerances 1mm Minimum measurements indicated by an asterix A B C D E F G x Y Zz TEF 2870 lt B 2 gt 200 175 gt Cx2 67 0 026xD 700 465 55 200 210 Recommended practical measurements A B C D E F G X y Z 700 465 55 200 210 TEF 2870 400 200 US 350 58 LAMP REPLACEMENT WARNING DO NOT OPEN MAINTAIN OR SERVICE IN AN AREA WHERE AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT Use a 19mm wrench to screw off lid Twist off lamp and replace Screw lid back on Tightening force 5 Nm Recommended mounting method of double tier navigation lights 4966 TEF 2870Ex NAVIGATION LIGHT USER MANUAL SPARE PARTS TECNICAL DATA Description Part No Light source P28S 24V 40W 9400 049 Light source P28S 230V 65W 9400 052 Mounting bracket for 1 pipe 0000 2600 Mounting bracket for 2 pipe 0000 2440 Lamp holder P28S 5088 0019 Gasket junction box 5003 0164 O ring top lid 5000 0051 Cable gland M20 M20 Ex nR 6 5 14mm 5030 0000 Gland PG9 3 5 8mm for restricted breathing test 5656 z Tranberg AS Strandsvingen 6 P O Box 8033 N 4068 Stavanger Norway TRANBERG Tel 47 51 57 89 00 Fax 47 51 57 89 50 info tranberg com www tranberg com Reg no NO 986 926 909 MVA Declaration of Conformity We Manufacturer Tranberg AS Address Strandsvingen 6 Gausel Responsible representative Tranberg AS Address Strandsvingen 6 Gausel Declare under
6. ould be used acid resistant stainless steel fixing screws bolts Never paint navigation light or any of its components Use only spare parts as described Regular tools required for installation e Wrench es suitable for selected M10 bolts for fixing navigation light to mast ships structure e Flat screwdriver for opening junction box e 2 mm wrench for installing of cable gland e Small flat screwdriver for terminating wires MAINTENANCE INSTRUCTIONS Gasket for junction box shall be replaced at intervals of one year Part No 5003 0164 Gasket shall be of same type as original One replacement gasket is included in shipment The navigation light should be inspected according to Company routines The manufacturer suggests regular check for water intrusion condensation which should be removed immediately When cleaning use only mild detergents Alcohol or petroleum based products may damage lens paint or plastic components At intervals according to company routines the restricted breathing properties should be verified Remove stopping plug at test port PG9 See illustration below Connect pressure meter vacuum pump and conduct test according to IEC 60079 15 2010 23 2 3 2 1 1 Note PG9 gland for connection of 3 5 8mm hose is included in shipment Note According to approval test of restricted breathing properties is not required Point for connecting bonding wire INSTALLATION INSTRUCTIONS TOOLS REQUIRED
Download Pdf Manuals
Related Search