User Manual - Universal Fibre Optics
Contents
1. Do not touch or attempt to remove the lamp while it is hot e Ensure that the power supply is correct for the unit before powering it up Always ensure that the unit is properly EARTHED Do not expose the unit to rain or moisture Keep away from all combustible materials e Never attempt to tamper with the wiring or other internal components Keep the unit away from gas oil and any other flammable or explosive materials e Indoor use only Universal Fibre Optics a LIGHTSOURCE LAYOUT Item Description CO CI COI a Compact DMX Light Source Range INSTALLATION GUIDE In order for the Compact light source to function safely and efficiently it must be installed according to this user manual Please read all sections thoroughly before switching on the light source POWER SUPPLY REQUIREMENTS Before plugging in the unit please make sure that the supply is correct Failure to do so could cause the unit to malfunction The unit requires a 240VAC 50Hz supply and it MUST BE EARTHED The light source units are provided with a cordset fitted with a standard 3 pin plug POSITIONING THE UNIT Standard horizontal mounting on shelf table Vertical mounting fixed to wall Upside down mounting fixed to underside of shelf The light source can be mounted horizontally vertically or upside down on any flat surface Keyhole slots are provided on the base of the unit to allow for securing to a surface The2. UFO Light Source User Guide LR 4 Compact DMX Light Source Models covered by this manual UFO 150 CDMXG Glass DMX 240V UFO 150 CDMXP Plastic DMX 240V Universal Fibre Optics Home Place Coldstream TD12 4DT United Kingdom Tel 44 0 1890 883416 Fax 44 0 1890 883062 Issue 2 Revised 23092013 www fibreopticlighting com INTRODUCTION Thank you for purchasing this UFO Light Source Please read these instructions fully before connecting your unit to the electrical supply and keep them for future reference The UFO Compact DMX are a range of low profile light sources which use 150W metal halide discharge lamps to give much greater brightness than those powered by halogen lamps These models have a fast re lamping feature the lamp is mounted on a pull out hatch at the rear and are fitted with a DMX controller allowing a range of in built effects or control via a standalone controller We do not recommend that the light source be left on for 24 hours a day 7 days a week as lamp life will be impaired A switch off of 30mins per day is recommended IMPORTANT THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED Do not operate without complete lamp enclosure in place or if lens is damaged KEEP HARNESS IN PLACE WHEN IN OPERATION CAUTION Hot surface Keep away from curtains and other c
3. Unplug the old lamp from its ceramic holder 5 Plug the new lamp into the holder making sure that you use a bulb of the same specification as to that which was removed Also make sure not to touch the glass part of the lamp 6 Slide the lamp holder plate back into position and tighten the two retaining nuts FUSE REPLACEMENT 1 Unplug unit from electrical supply and allow to cool 2 The fuse is located in a drawer under the mains input connector There is also a spare fuse located in this drawer 3 Open the fuse drawer 4 Withdraw fuse from its holder 5 Replace with identically specified fuse see specification table in this manual 6 Close the fuse drawer and power up the light source Universal Fibre Optics se MAINTENANCE Continued CLEANING THE UNIT Disconnect unit from power supply and allow to cool before attempting any cleaning of the unit A visual check of the unit should be completed every 12 months However cleaning should take place as and when required The body of the unit can be cleaned with a soft damp cloth do not use any abrasives on the unit The fans and vents should be kept clear by periodically blowing them out with compressed air Glass filter to be cleaned with soap and water then dried Please note that a record of all maintenance MUST be kept in the table below indicating what maintenance was undertaken and when This must be DATED for warranty purposes Mainten
4. ance Undertaken sa Compact DMX Light Source Range TROUBLESHOOTING Problem Probable cause s Remedy Unit is completely dead Check and replace fuse Lamp and LED power indicator are not No powerto unit illuminated Check that power is switched on and power supply is plugged in Allow unit to cool for 5 to 10 Thermal switch activated minutes and investigate reason for LED power indicator amp fan OM INET are on but no light is out t d Check plug connection ensure lamp is properly seated in its holder and the pins are fully mated Lamp wires are not connected Lamp needs replacing Replace lamp Unit needs cleaning Clean glass lens Poor light output Incorrect power supply Ensure power supply is 240VAC 50Hz Ensure fibre port connector is plugged in correctly and that the screw is tightened up properly Fibre port connector not plugged in correctly Allow unit to cool for 5 to 10 Unit is overheating minutes and investigate reason for overheating Lamp going on amp off randomly Please complete troubleshooting procedures before returning unit to us for further investigation Universal Fibre Optics TECHNICAL SPECIFICATIONS Description Port connector size Fibre type Supply voltage Lamp power Input power Start up current Running current Min ambient temp Max ambient temp Thermal protection Ballast type Fan tye polymer fibre Fan type glass fibre Power cord Main fus
5. be displayed PL After a short delay may RESET the small indicator will flash confirming programme mode P01 is set as shown below The Light Source will display white light PU Scroll through the Built in Programs until the desired programme is reached there will be a short delay may RESET until the small indicator flashes confirming the address is set The set programme will now run The programme will only run if left in this mode returning to the Address Mode will stop the program running To return to Address Mode press the 2 buttons to the left of the display Items 2 amp 3 Page 1 simultaneously three times Note 1 There is an Auxiliary mode which may be displayed as shown below This is not used If in this mode press the 2 buttons simultaneously twice to return to Address mode HL Note 2 In Master Slave and Remote DMX controller operation the small indicator flashes to indicate DMX data transmission Universal Fibre Optics E BUILT IN PROGRAMS Program number Function E E E E oo Ma OO ES E WY G 0 M B C J flash change 30 seconds O A e E DEAN Compact DMX Light Source Range BUILT IN PROGRAMS Program number Function P37 8 colours chasing slow change 1 0 RPM P38 8 colours chasing slow change 2 0 RPM P39 8 colours chasing slow change 3 0 RPM P40 8 colours chasing slow change 5 0 RPM PS1 WY G 0 M B C J audio control PS2 WY G 0 M B C J audio control PS3 WyY G audio c
6. e Lamp type Lamp model Lamp life Lamp colour temp Lamp CRI Control options DMX channels Protocol Colour wheel Standard colours Acoustic rating polymer fibre Acoustic rating glass fibre Operating environment Protection rating Material Colour Size Weight 150W DMX or CDM c 9000h SA T c 12000h CDM 4200K SA T 3000K CDM 95 SA T 88 CDM 38 0dB A 23 0dB A lamp life as stated by manufacturer in optimum conditions Compact DMX Light Source Range NOTES Universal Fibre Optics 16 NOTES Compact DMX Light Source Range NOTES Universal Fibre Optics 1 Universal Fibre Optics Home Place Coldstream TD12 4DT United Kingdom Tel 44 0 1890 883416 Fax 44 0 1890 883062 www fibreopticlighting com
7. light source is only suitable for use in a dry area If the unit is being mounted at a higher than the ground level block access below the work area before installing Verify that any screws or bolts can safely bear the weight of the light source Universal Fibre Optics a INSTALLATION GUIDE Continued Verify that the supporting structure can safely bear the weight of all installed units cables and any other equipment The minimum thickness of the mounting surface must be no less than 19mm For horizontal mounting it is recommended that the lightsource is secured to a solid surface using 4 x M4 or M5 screws or bolts and the keyhole slots This is particularly important if the lightsource location is not at ground floor level To mount the light source vertically first securely install 4 x M4 or M5 screws or bolts at the required distances so that they will line up with the keyhole slots The light source can then be mounted onto them and slid into position The bolts or screws MUST then be fully tightened To mount the light source under a surface first securely install 4 x M4 or M5 screws or bolts at the required distances so that they will line up with the keyhole slots The light source can then be mounted onto them and slid into position The bolts or screws MUST then be fully tightened 173mm CLEARANCE VENTILATION It is imperative that a gap of 200mm 8 or more is left around the unit This is to allow air t
8. o circulate and prevent overheating The location must have free ventilation 5 Compact DMX Light Source Range INSTALLATION GUIDE Continued CONNECTION There are 3 main connections required the fibre port the mains power and the DMX connections Connect and secure the fibre optic connector to the fibre port before connecting the electrical supply Never run the light source with the fibre connector unplugged The fibre optic connector is secured into the port by removing the small cover on the top of the light source see item 11 on page 3 and tightening the retaining screw The cover should then be replaced DMX data connections are provided at the rear of the Light Source connection details as follows CONNECTIONS 1 Ground Screen 2 DMX Data 3 DMX Data FEMALE DMX OUT Like all data networks the DMX cable should be terminated on the DMX OUT of the last Light Source on the network using a terminator plug OPERATION This light source can be operated in stand alone mode or can be connected to a compatible DMX controller In Standalone Mode the Compact DMX can be used as a single independent Light Source or in a Master Slave configuration with several Light Sources connected together using DMX leads In Master Slave configuration all addresses are set the same and whatever programme is selected on the Master DMX Light Source will also be observed on the Slave Light Sources In DMX mode
9. ombustible materials WARNING RISK OF FIRE INJURY TO PERSONS Keep away from combustibles Unplug to change lamp Do not touch lamp WARNING RISK OF FIRE Do not place lamp where the overhead surface is closer than 0 2m to the light source a Compact DMX Light Source Range IMPORTANT SAFETY INFORMATION INSTRUCTIONS PERTAINING TO A RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS Lighted Lamp is HOT WARNING To reduce the risk of FIRE ELECTRIC SHOCK OR INJURY TO PERSONS 1 Unplug and allow to cool before replacing lamp 2 Lamp gets HOT quickly Only contact plug when turning on 3 Do not touch hot lens guard or enclosure 4 Do not remain in light if skin feels warm 5 Do not look directly at lighted lamp 6 Keep lamp away from materials that may burn 7 Use only the correct lamp wattage as detailed on the serial label Failure to adhere to this will cause damage to the unit 8 Do not touch the lamp at any time Use a soft cloth Oil from skin may damage lamp 9 Do not operate product with missing or damaged guard lamp containment barrier lens or fibre optic harness 10 WARNING Lamp types are matched to the ballast and different wattages types cannot be used SAVE THESE INSTRUCTIONS e Always disconnect the unit from the power supply before opening or attempting to perform any work on it e UNIT MAY GET HOT always allow unit to cool down before handling or moving it
10. ontrol PS4 WY G O audio control Universal Fibre Optics DMX ADDRESSES Channel No Function Address Value Effect Effect Colourwheel Dimmer wheel versions versions Snap to colour Clear white Dim level 1 Snap to colour 16 31 Colour 1 yellow Dim level 2 E Snap to colour 32 47 Colour 2 green Dim level 3 O Snap to colour 48 63 Colour 3 orange Dim level 4 01 Snap to colour 64 79 Colour 4 Dim level 5 magenta Snap to colour 80 95 Colour 5 blue Dim level 6 Snap to colour 96 111 Colour 6 cyan Dim level 7 Snap to colour 112 127 Colour 7 jade Dim level 8 01 9 colour sequence 128 143 CY G 0 M B C J N A 5 seconds 5 seconds 01 9 colour sequence 144 159 CY G 0 M B C J N A 7 seconds 7 seconds 01 9 colour sequence 160 175 CY G O M B C J N A 12 seconds 12 seconds 01 9 colour sequence 176 191 CY G 0 M B C J N A 15 seconds 15 seconds 01 9 colour sequence 192 207 CY G O M B C J N A 20 seconds 20 seconds 01 9 colour sequence 208 223 CY G 0 M B C J N A 60 seconds 60 seconds Compact DMX Light Source Range MAINTENANCE LAMP REPLACEMENT Recommend Lamp change every 12 months for Metal Halide Lamps should not be run to the end of their life 1 Unplug unit from electrical supply and allow to cool 2 On the rear of the unit unscrew the two knurled securing nuts A which hold the lamp holder in position 3 Use the handle B to withdraw the lamp holder C from the light source 4
11. the DMX controller can be programmed to control Compact DMX Light Sources either in a block all same addresses or independently all different addresses Universal Fibre Optics e INSTALLATION GUIDE Continued OPERATION Continued When the DMX Light Source is powered up the unit will RESET during which the following flashing message will be displayed on the front panel display Item 4 Page rEs When the Light Source is RESET the following message will be displayed UU This indicates the Light Source has been set to address 001 by default PROGRAMMING At any stage during programming when changes are made the DMX may go through the RESET phase as described above this is normal Changing Address To change the address press the 2 buttons to the left of the display Items 2 amp 3 Page 1 simultaneously once the small indicator in the bottom right of the display will go out Scroll for the required address as follows SCR DOWN OLL SCROLL ur Once the selected address is found there will be a short delay may RESET untilthe small indicator illuminates confirming the address is set 7 Compact DMX Light Source Range INSTALLATION GUIDE Continued PROGRAMMING Continued Colour Wheel Built in Programs To access the built in programmes as described in the User Guide proceed as follows Press the 2 buttons to the left of the display Items 2 amp 3 Page 1 simultaneously twice and the following message will
Download Pdf Manuals
Related Search