MODEL: VS862 - Tooled
Contents
1. Select Read Codes from the Select Function menu and press the Y button 151107 10 lt V2 4 SOFTWARE VS862 2 151107 Select F gt 1 Read Codes 2 Erase Codes 3 ECU Information 4 Readiness Test If there are no Diagnostic Trouble Codes present the display will indicate NO CODES ARE STORED IN THE MODULE If there are any Diagnostic Trouble Codes present the DTC number and its definition will show on the LCD display The sub code the communication protocol the sequence of the DTC currently being observed and the total number of codes detected will be observed on the upper right hand corner of the display When a DTC s definition covers more than one display screen use the Y button as necessary to view any additional information If the DTC definition is not available an advisory message prompting you to refer to the vehicle service manual will be observed on the display If more than one DTC is found use the UP DOWN scroll buttons as necessary until all the codes have been shown up 16627 100 CA Solenoid Valve A For Boost Pressure Control N75 Malfunction P0243 11 lt V2 4 SOFTWARE Erasing Codes CAUTION Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle s on board computer but also Freeze Frame data and manufacturer specific enhanced data Further the IM Readiness Monitor Status for all vehicle monitors is re2. Do not soak the keypad as the keypad is not waterproof 2 6 Power The external power of the scan tool is provided via the vehicle Data Link Connector DLC Just follow the steps below to turn on the scan tool 1 Connect the OBD II Cable to scan tool 2 Find DLC on vehicle refer to proprietary handbook 3 A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the OBD2 cable 4 Plug OBD II Cable to the vehicle s DLC 2 7 Product Setup The scan tool allows you to make the following adjustments and settings 1 Contrast Adjustment Adjusts the contrast of the LCD display 2 Display Test Tests the LCD display 3 Keyboard Test Tests the keyboard To enter the setup menu mode 1 From the keyboard Press and hold the N button for at least 3 seconds until the System Setup menu shows up Follow the instructions to make adjustments and settings as described in the following setup options gt 1 Contras 2 Display Test 3 Keyboard Test VS862 2 151107 5 lt V2 4 SOFTWARE 2 From the Main Menu Use the UP DOWN Scroll Buttons to select System Setup and then press the Y button Follow the instructions to make adjustments and settings as described in the following setup options Main Menu 1 VW AUDI 2 OBDII EOBD 3 Oil Service gt 4 System Setup Contrast Adjustment 1 From the System Setup menu use the UP DOWN scroll buttons to select Contrast and press t
3. ramps and is chocked v Put transmission in PARK for automatic transmission or NEUTRAL for manual transmission and make sure the parking brake is engaged S Wear approved eye protection A full range of personal safety equipment is available from your Sealey dealer Wear suitable clothing to avoid snagging Do not wear jewellery and tie back long hair O WARNING Use extreme caution when working around the ignition coil distributor cap ignition wires and spark plugs These components create hazardous voltages when the engine is running gt x lt DO NOT connect or disconnect any test equipment with ignition on or engine running V Keep a fire extinguisher suitable for gasoline chemical electrical fires nearby Y Account for all tools and parts being used and do not leave them on or near the engine J Keep code reader dry clean and free from oil water and grease Use a mild detergent on a clean cloth to clean the outside of the tool V Operate the vehicle in a well ventilated work area exhaust gases are poisonous IMPORTANT Always refer to the vehicle manufacturer s service instructions to establish the current procedure and data These instructions are provided as a guide only O WARNING The warnings cautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur It must be understood that common sense and caution are factors which cannot be built into t
4. Instructions For VAG CODE READER AND RESET TOOL EOBD amp GENERIC MODEL VS862 SOFTWARE lt V2 4 Table of Contents e Section No Page No e 1 Safety Precautions and Warnings 2 e 2 Product Information 3 e 2 1 Description 3 e 2 2 Specifications 4 e 2 3 Accessories Included 4 e 2 4 Navigation Characters 4 e 2 5 Keyboard 5 e 2 6 Power 5 e 2 7 Product Setup J e 2 8 Vehicle Coverage 8 e 3 Operating Instructions 9 e 3 1 VW AUDI Diagnostics 9 e 3 2 OBDH EOBD Diagnostics 15 e 3 3 Oil Service 19 Thank you for purchasing a Sealey product Manufactured to a high standard this product will if used according to these instructions and properly maintained give you years of trouble free performance A IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY NOTE THE SAFE OPERATIONAL REQUIREMENTS WARNINGS AND CAUTIONS USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED FAILURE TO DO SO MAY CAUSE DAMAGE AND OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY VS862 2 151107 1 lt V2 4 SOFTWARE 1 SAFETY INSTRUCTIONS O WARNING Ensure that Health and Safety local authority and general Workshop practice regulations are strictly adhered to x DO NOT use the unit if it or any attachment is damaged Maintain the unit in good and clean condition for best and safest performance S If required ensure that the vehicle to be worked on is adequately supported with axle stands or
5. Oil menu VS862 2 151107 20 lt V2 4 SOFTWARE Service Reset RESET OK Press any key to con 4 To set oil type use UP DOWN scroll button to select Set Oil Type from Longlife Oil menu and press Y button gt 1 Diesel 2 V6Tdi 3 Petrol 4 Non Longlife Oil 5 Use UP DOWN scroll button to select an oil type according to that of your vehicle 6 Press any key to return to Longlife Oil menu Oil Type Reset RESET OK Press any key to con 7 To view oil type use UP DOWN scroll button to select View Oil Type from Longlife Oil menu and press Y button VS862 2 151107 21 lt V2 4 SOFTWARE Loneglife Oil 1 Service Reset 2 Set Oil Type gt 3 View Oil Type 8 View oil type on screen and press any key to return to Lifelong Oil menu View Oil Type Non longlife Oil Press any key to con Resetting Non Longlife Oil Service 1 To reset non longlife oil service use UP DOWN scroll button to select Non Longlife Oil from the Oil Service menu and press Y button Oil Service 1 Longlife Oil gt 2 Non Longlife Oil 3 Set Insp Interval 2 Use UP DOWN scroll button to select from the Service Reset Non Longlife Oil menu and press Y button VS862 2 151107 22 lt V2 4 SOFTWARE Non Longlife Oil 1 Service Reset 3 Press any key to return to previous menu RESET OK Press any key to con Setting Inspection Interval Set Insp Interval is used t
6. button e Different vehicle supports different oil service channels so retrieved channel numbers may vary from one vehicle to another Normally a vehicle supports 3 5 channels e 1 3 to the upper right corner of the screen indicates the total number of supported channels and their sequence 9 Use UP DOWN scroll button to select lt Save gt and press Y button to save your settings VS862 2 151107 25 lt V2 4 SOFTWARE Oil Service lt Back gt Save Back Cont to Set Save Save Setup Exit Cancel Setup 10 Press any key to return to Main Menu Manual Setup RESET OK Press any key to cont If you want to continue to change values use UP DOWN scroll button to select lt Back gt and press Y button to return to Min Mil to Service menu If you want to cancel all setups use UP DOWN scroll button to select lt Exit gt and press Y button or simply press N button to return to the Main Menu NOTE It is our policy to continually improve products and as such we reserve the right to alter data specifications and component parts without prior notice IMPORTANT No liability is accepted for incorrect use of product WARRANTY Guarantee is 12 months from purchase date proof of which will be required for any claim INFORMATION For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address including postcode Sole UK Distributor E 01284 757500 A www s
7. ealey co uk Sealey Group VS862 2 151107 Bury St Edmunds Suffolk 01284 703534 FA sales sealey co uk 26 lt V2 4 SOFTWARE
8. eturn to previous menus VS862 2 151107 18 lt V2 4 SOFTWARE 3 3 Oil Service 1 Turn the ignition off 2 Locate the vehicle s 16 pin Data Link Connector DLC 3 Plug the OBDII connector to the vehicle s DLC 4 Turn the ignition on But do not start the engine 5 Press the Y button The Main Menu will be observed on the display 6 Use UP DOWN scroll button to select Oil Service from the menu and press the Y button Main Menu 1 VW AUDI 2 OBDII EOBD gt 3 Oil Service 4 System Setup 7 Use UP DOWN scroll button to select vehicle maker and press Y button Oil Service 1 Auto Detect 2 Audi 3 VW 4 Seat 5 Skoda 8 Use UP DOWN scroll button to select a vehicle and press Y button to confirm VS862 2 151107 19 lt V2 4 SOFTWARE Select Vehicle 01 Golf 3 02 Golf 4 gt 3 New Beetle 04 Passat 05 Passat BS 06 Passat 97 e If your vehicle is not listed on the screen use UP DOWN scroll button to select Others from the menu and press Y button to confirm Resetting Longlife Oil Service 1 Use UP DOWN scroll button to select Longlife Oil from the menu and press Y button Oil Service gt 1 Longlife Oil 2 Non Longlife Oil 3 Set Insp Interval 2 Use UP DOWN scroll button to select Service Reset from Longlife Oil menu and press Y button Longlife Oil gt 1 Service Reset 2 Set Oil Type 3 View Oil Type 3 Press any key to return to Longlife
9. he Y button System Setup gt 1 Contrast 2 Display Test 3 Keyboard Test 2 From the Contrast menu use the UP DOWN scroll buttons to increase or decrease the contrast Contrast 45 Use A or Y to change 3 Press the Y button to save your selection and return to previous menu 4 Press the N button to return to previous menus VS862 2 151107 6 lt V2 4 SOFTWARE Display Test The Display Test is used to check the LCD display 1 From the System Setup menu use the UP DOWN scroll buttons to select Display Test and press the Y button System Setup 1 Contrast gt 2 Display Test 3 Keyboard Test 2 Press the Y button again to start test Look for missing spots in the solid black characters Press Y to test Look for missing spots in characters Press lt N gt to return 3 When completed press the N button to return Keyboard Test The Keyboard Test is used to verify that the keys are functioning properly 1 Use the UP DOWN scroll buttons to select Keyboard Test from System Setup menu and then press Y button VS862 2 151107 T lt V2 4 SOFTWARE System Setup 1 Contrast 2 Display Test gt 3 Keyboard Test 2 Press any key to start test When you press a key the key name should be observed on the display If the name does not show up then the key is not functioning properly Press any key to Start test to display name Key Double N to Retur
10. his product but must be applied by the operator VS862 2 151107 2 lt V2 4 SOFTWARE 2 PRODUCT INFORMATION 2 1 Description 1 LCD DISPLAY Indicates test results Backlit 128 x 64 pixel display with contrast adjustment 2 Y BUTTON Confirms a selection or action from a menu When a DTC s definition covers more than one screen it is used to move down to the next screen for additional data IMPORTANT We are constantly improving the operating of this tool to work with other VAG vehicles In the event that your VS862 will not connect to a vehicle or it appears not to communicate with a specific vehicle type we recommend that you download the latest operating software and DTC library from the Sealey website www sealey co uk and update your VS862 with the latest code and retry your problem vehicle VS862 2 151107 3 lt V2 4 SOFTWARE 2 2 2 4 3 N BUTTON Cancels a selection or action from a menu or returns to the menu It is also used to set up the unit when being pressed and held for at least 3 seconds 4 A UP SCROLL BUTTON Moves up through menu and submenu items in menu mode When more than one DTC is retrieved moves up through the current screen to the previous screens for additional DTCs and definitions 5 X DOWN SCROLL BUTTON Moves down through menu and submenu items in menu mode When more than one DTC is retrieved moves down through the current screen to the next screens for additi
11. n 3 Double press N to return to the previous menu 2 8 Vehicle Coverage The VS862 VW AUDI Code Scanner is specially designed to work with most Volkswagen and Audis sold worldwide of 1990 or newer models If a VW AUDI has a 16 pin OBD II style Data Link Connector DTC the code reader will work If it has an old style 2x2 Data Link Connector DTC then it depends on whether there are 4 or 3 wires connecting to the pins If there are 4 wires each connecting a pin then it will work If there are only 3 wires leaving one pin disconnected then it will not work For VW AUDI with old style 2x2 Data Link Connector DTC you need to have a 2x2 cabling adapter which is not included in this product package Order No VS8X01 VS862 2 151107 8 lt V2 4 SOFTWARE 3 OPERATING INSTRUCTIONS 3 1 VW AUDI Diagnostics Reading Codes CAUTION Do not connect or disconnect any test equipment with ignition on or engine running 1 Turn the ignition off 2 Locate the vehicle s 16 pin Data Link Connector DLC 3 Plug the OBDII connector to the vehicle s DLC 4 Turn the ignition on But do not start the engine 5 Press the Y button The Main Menu will be observed on the display 6 Use the UP DOWN scroll buttons to select VW AUDI from the menu and press the Y button Main Menu gt 1 VW AUDI 2 OBDIH EOBD 3 Oil Service 4 System Setup 7 Use the UP DOWN scroll buttons to select the system from the Select Sy
12. o set oil service interval of different channels of various vehicles To enter Set Insp Interval menu 1 Use UP DOWN scroll button to select Auto Detect from Oil Service menu and press Y button Oil Service gt 1 Auto Detect 2 Audi 3 VW 4 Seat 5 Skoda 2 Press any key to enter Set Insp Interval menu VS862 2 151107 23 lt V2 4 SOFTWARE Manual Setup Can t Auto Detect Please Try Others Press any key to cont It is recommended to use Auto Detect to enter Set Insp Interval menu 3 Or use UP DOWN scroll button to select Set Insp Interval from the menu and press Y button Oil Service 1 Longlife Oil 2 Non Longlife Oil gt 3 Set Insp Interval 4 Use UP DOWN scroll button to change value as desired Min Mil to Service Channel No 42 Mil Current Value 9000 Set Value lt 9 000 gt N Next Y Save Exit A Change Setup 5 Use N button to move to next setup screen VS862 2 151107 24 lt V2 4 SOFTWARE Mil Since Service Channel No 40 Mil Current Value 700 Set Value lt 700 gt N Next Y Save Exit A Change Setup 6 Use UP DOWN scroll button to change value as desired 7 UseN button to move to next setup screen Time Since Service 3 3 Channel No 41 Day Current Value 15 Set Value o N Next Y Save Exit A Change Setup 8 Use UP DOWN scroll button to change value as desired and press Y
13. onal DTCs and definitions 6 OBD II CONNECTOR Connects the scan tool to the vehicle s Data Link Connector DLC Specifications 1 Display Backlit 128 x 64 pixel display with contrast adjustment 2 Operating Temperature 0 to 50 C 32 to 122 F 3 Storage Temperature 20 to 70 C 4 to 158 F 4 External Power 8 0 to 15 0 Volts provided via vehicle battery 5 Dimensions Length Width Height 178 mm 7 00 95 mm 3 75 34 mm 1 35 6 NW 0 70kg 1 54lb GW 1 0kg 2 20Ib Audi Seat Skoda VW Beetle Golf GTI Jetta Passat Touareg Touran 2 3 Accessories Included 1 User s Manual Instructions on tool operations 2 OBD2 cable Provides power to tool and communicates between tool and vehicle 3 Serial Cable Used to upgrade the scan tool 4 Carry Case A nylon case to store the scan tool when not in use Navigation Characters Characters used to help navigate the scan tool are 1 bp Indicates current selection 2 A flashing down arrow indicates additional information is available on the next screen VS862 2 151107 4 lt V2 4 SOFTWARE 3 1 A flashing up arrow indicates additional information is available on the previous screen 4 pd Identifies a pending DTC when viewing DTCs 2 5 Keyboard Do not use solvents such as alcohol are allowed to clean the keypad or display Use a mild nonabrasive detergent and a soft cotton cloth
14. play When a DTC s definition covers more than one display screen use the Y button as necessary to view any additional information If the retrieved DTCs contain any manufacturer specific or enhanced codes you will be prompted to refer to the CD DTC library or the vehicle service manual to view the DTC definitions 10 If more than one DTC is found use the UP DOWN scroll buttons as necessary until all the codes have been shown up Erasing Codes 1 If you decide to erase the DTCs use the UP DOWN scroll buttons to select Erase Codes from the OBDIT EOBD DIAG menu and press the Y button VS862 2 151107 OBDH EOBD DIAG gt 1 Read Codes 2 Erase Codes 17 lt V2 4 SOFTWARE e If the scan tool is not connected or no communication is established with the vehicle yet then refer to Reading Codes from to 8 at Paragraph 3 2 2 A warning message comes up asking for your confirmation Erase Codes Erase Trouble Codes Are you sure lt YES gt NO 3 Ifyou do not want to proceed with erasing the codes press the N button to exit A message of command cancelled will show up 4 Ifyou do wish to proceed to erase the codes then press the Y button 5 If the codes are cleared successfully an ERASE DONE confirmation will show on the display Press any button to return to previous menus 6 If the codes are not cleared then an ERASE FAILURE message will appear Press the N button to r
15. rative System Monitor e Heated O2 O2 Sensor Heater Monitor e Sec Air Inject Secondary Air Monitor e A C A C system Monitor e Catalytic Conv Catalytic Convertor Monitor VS862 2 151107 14 lt V2 4 SOFTWARE Readiness Test EGR Sys Heated O2 O2 Sensor s A C Sec Air Inject EVAP Sys 3 Press the N button to return to previous menus 3 2 OBDIT EOBD Diagnostics Reading Codes CAUTION Don t connect or disconnect any test equipment with ignition on or engine running 1 2 3 4 5 6 1 Turn the ignition off Locate the vehicle s 16 pin Data Link Connector DLC Plug the OBDII connector to the vehicle s DLC Turn the ignition on But do not start the engine Press the Y button The Main Menu will be observed on the display Use the UP DOWN scroll buttons to select OBDH EOBD from the menu Main Menu 1 VW AUDI gt 2 OBDII EOBD 3 Oil Service 4 System Setup Press the Y button A sequence of messages showing the OBDII EOBD protocols will be observed on the display until the vehicle protocol is detected VS862 2 151107 15 lt V2 4 SOFTWARE If the scan tool fails to communicate with the vehicle s ECU Engine Control Unit a LINK ERROR message shows up on the display e Verify that the ignition is ON e Check if the scan tool s OBD II connector is securely connected to the vehicle s DLC e Verify that the vehicle is OBDIH EOBD compliant e T
16. set to Fail status Do not erase the codes before the system has been checked completely by a technician 1 If you decide to erase the DTCs use the UP DOWN scroll buttons to select Erase Codes from Select Function menu and press the Y button Select Function 1 Read Codes gt 2 Erase Codes 3 ECU Information 4 Readiness Test e If the scan tool is not connected or no communication is established with the vehicle yet then refer to Reading Codes from 1 to 7 at Paragraph 3 1 2 A warning message comes up asking for your confirmation Erase Codes Erase Trouble Codes Are you sure lt YES gt NO 3 Ifyou do not want to proceed with erasing the codes press the N button to exit A message of command cancelled will show up 4 Ifyou do wish to proceed to erase the codes then press the Y button VS862 2 151107 12 lt V2 4 SOFTWARE 5 Ifthe codes are cleared successfully an ERASE DONE confirmation message will show on the display Press any button to return to the previous menus 6 Ifthe codes are not cleared then an ERASE FAILURE message will appear Press the N button to return to previous menus Viewing ECU Information 1 Toview ECU Information use the UP DOWN scroll buttons to select ECU Information from Select Function menu and press the Y button Select Function 1 Read Code 2 Erase Code gt 3 ECU Information 4 Readiness Test If the scan tool is not connec
17. stem menu and press the Y button VS862 2 151107 9 lt V2 4 SOFTWARE 8 VS862 2 Tr Select System gt 01 Engine 02 Auto Trans 15 Airbags 03 ABS Brakes 08 Auto HVAC 09 Cent Elect If the scan tool fails to communicate with the selected vehicle s ECU Electronic Control Unit a LINK ERROR message shows up on the display Verify that the ignition is ON Check if the scan tool s OBD II connector is securely connected to the vehicle s DLC Verify that the module is supported Turn the ignition off and wait for about 10 seconds Turn the ignition back to on and repeat the procedure from step 5 If the LINK ERROR message does not go away then there might be problems for the scan tool communicating with the module being tested The most common cause is that the scanned module ts not supported on the vehicle IMPORTANT We are constantly improving the operating of this tool to work with other VAG vehicles In the event that your VS862 will not connect to a vehicle or it appears not to communicate with a specific vehicle type we recommend that you download the latest operating software and DTC library from the Sealey website www sealey co uk and update your VS862 with the latest code and retry your problem vehicle The numbers 01 02 15 03 08 etc in front of the system names refer to the physical addresses assigned to the systems not the sequence of the systems to be arranged
18. ted or no communication is established with the vehicle yet then refer to Reading Codes from to 7 at Paragraph 3 1 ECU Information VAG No 06A906032TF Component Bosch 1 815VT 0020 Coding 0008570 Imp 0000 WSC 000078 If there is no ECU Information available a warning message shows on the display 2 Press the N button to return to previous menus VS862 2 151107 13 lt V2 4 SOFTWARE Readiness Test Important The Readiness Test function ts used to check the operations of the Emission System on OBD2 EOBD compliant vehicles It is an excellent function to use prior to having a vehicle inspected for compliance to an emissions program e Pass Indicates that a particular monitor being checked has completed its diagnostic testing e Fail Indicates that a particular monitor being checked has not completed its diagnostic testing or the monitor ts not supported on that vehicle 1 Use the UP DOWN scroll buttons to select Readiness Test from Select Function menu and press the Y button Select Function 1 Read Code 2 Erase Code 3 ECU Information gt 4 Readiness Test e Ifthe scan tool is not connected yet then refer to Reading Codes from l to 7 at Paragraph 3 1 2 Use the UP DOWN scroll buttons as necessary to view the status of the following monitors e EGR Sys EGR System Monitor e Q 2 Sensor s O2 Sensors Monitor e Catalyst Catalyst Monitor e EVAP Sys Evapo
19. urn the ignition off and wait for about 10 seconds Turn the ignition back to on and repeat the procedure from step 5 e Ifthe LINK ERROR message does not go away then there might be problems with the scan tool communicating with the vehicle Contact your local distributor for assistance 8 After the vehicle protocol is displayed on the screen press any key or wait about 2 seconds for the OBDII EOBD DIAG menu to come up 9 Use the UP DOWN scroll buttons to select Read Codes from the menu and press the Y button OBDII EOBD DIAG gt 1 Read Codes 2 Erase Codes e If there are no Diagnostic Trouble Codes present the display will indicate NO CODES ARE STORED IN THE MODULE e Ifthere are any Diagnostic Trouble Codes present the Fault Codes and Pending Codes will be reported on the display VS862 2 151107 16 lt V2 4 SOFTWARE P0118 Pd 06 06 1SO9141 09 iinet inher Pressure Control Solenoid A Control Circuit Low The DTC number will appear on the upper left hand corner and its definition will show on the body of screen The type of code Generic or Manufacturer specific the vehicle protocol the sequence of the DTC currently being observed the total number of codes detected and the module ID will be observed on the upper right hand corner of the display If the code being displayed is a pending code the Pd icon will be observed next to the DTC number on the upper right hand corner of the dis
Download Pdf Manuals
Related Search