Home

electrosec

1. appear after the commands On the left hand side of GSM DIALER the screen you will see 3 different digits indicating 3 different situations qp 1 If everyting is normal an antenna display level chart will appear increasing from left to right If the unit is not in the GSM coverage area the chart will be empty and will flash In this case please change the place of the unit or use an antenna extension 2 If you see this symbol flashing SIM card PIN code is not correct In this case D pleae enter the correct PIN code from 3 menu and turn off the unit and then turn it on again 3 If you see this symbol flashing SIM card is not inserted correctly In this case please make sure the SIM card is inserted correctly and the SIM socket is locked and turn off the unit and then turn it on again 2009 1 electrosec Page 3 6 GD USB User s manual The two different digits on the right hand side of the graphic 1 cD use indicates the external line or GSM line GSM DIALER 1 If you see this symbol on the grapfic it means connectors 3 and 4 has a connection failure In this case system calls will be made through GSM line When the connection is active the symbol flashes 2 If you see this symbol on the grapfic it means connectors 3 and 4 has a connection failure In this case system calls will be made through this line When the connection is active the symbol flashes PROG
2. each GSM number Click the names of the contacts you want to send SMS to and select SEND SMS The SMS should contain maximum 125 characters To read received messages click READ SMS If you have new messeges thay will appear on new messeges screen Use Clear Messeges to delete the messeges you want 1 9 ELECTROSEC SECURITY CO LTD Cemal sururi sk no 33 D1 2 mecidiyek y ISTANBUL TURKEY Tel 0090 212 2120310 Pbx Fax 0090 212 3474692 Email electrosec electrosec com Web www electrosec com 2009 1 electrosec Page 6 6
3. RAM MENUS After you make sure there is a no link in connectors 3 and 4 pick up the telephone and press Program menu will appear on screen Use 1 9 keys to enter program menus Properties of a menu will be deleted if you enter with To save use The details of menus 1 9 are as follows 1 Area Code This menu is very important for the system to work properly Suppose the GSM dialer is connected to an Alarm Station and the telephone number 2120310 is entered for the AHM When there is no connection failure the GSM dialer will communicate without any problem But when there is an external line failure the unit will dial the same number from GSM line the telephone number will be incomplete This is why the area code must be entered in the menu If there is already a number with 11 digits is entered 03 12xxxxxxx in the Alarm Station then there is no need enter the area code in this menu 2 Extension Number Suppose that GSM Dialer unit is connected to an Alarm Station one of the users internal line is used as an external line and telephone number 92120310 is entered in the Alarm Station 9 at the beginning 1s for exit code GSM dialer unit will communicate without any problem as long as there is an external line But the number will be imcomplete if the unit dials the same number via GSM line This is why a number for exit code must me entered in the Alarm Station 3 PIN CODE If there is a PIN Code assinged to t
4. different GSM numbers can be entered Following key 7 the sequence number is set and entered On the right hand side of the screen lat 2 digits appear X Maximum 14 characters can be entered After entering each number a digit will move right automatically The important point here is to enter the country code at the beginning of each GSM number For example if you want to enter GSM no 05332364947 you must enter 905332364947 SMS messages will be sent starting from line 1 8 AMS Control This menu is designed assuming the GSM dialer is not connected to an Alarm Station not connected to an AMS In this case GSM Dialer will send the information via SMS to the GSM numbers assinged in Menu 7 instead of an AMS Uses International Ademco Contatc ID format Factory settings are set as 2 Disabled To turn on this feature enter 1 ON and Alarm station connected must contain a 7 digit telephone number and 4 digit Customer Number in the AMS menu 9 SMS sending With this menu you can set the GSM dialer to send SMS or not Factory settings are set as 1 ON To turn off this feature and stop the unit to send SMS enter 2 Disabled 0 SMS sending with button With this menu you can enter emergency SMS with button Maximum 32 alphanumeric characters Please enter the same directions for Messege Header for this menu as well TE 2009 1 electrosec Page 5 6 GD USB User s manual After completing the settings in the Menus link the un
5. he SIM card please enter the PIN code using this menu 2009 1 electrosec Page 4 6 GD USB User s manual 4 Message Title GD USB unit is a professional device analysing the data between AMS and Alarm Station The result of this data analysis can be sent to a telephone number via SMS if desired To see the source of these SMS messegas 16 digit information can be entered using this menu Factory settings show GSM Dialer Unit by default You may change this if you desire Use keys 1 9 to enter alphanumeric characters If alphanumeric characters are not avaliable on the telephone you may get help by checking the keys of a mobile phone 5 User Name With this menu Alarm Users names are entered It is important as the user names will appear on the SMS messages Maximum 9 different users can be entered Following key 5 the user no is entered Factory settings are name OX Maximum 8 characters can be entered Please enter the same directions for Messege Header for this menu as well 6 Area Name With this menu Area Names used in the Alarm are entered It is important as the area names will appear on the SMS messages Maximum 9 different areas can be entered Following key 6 the area name is entered Factory settings are area 0X Maximum 8 characters can be entered Please enter the same directions for Messege Header for this menu as well 7 GSM Number With this menu the GSM numbers for sending SMS messeges are set Maximum 3
6. is on the right 2009 1 electrosec Page 2 6 GD USB User s manual PROGRAMMING To program after inserting the SIM card connect a basic telephone to connector no 7 8 considering the polarisation link the power supply to connector no 1 2 as shown in page 2 In this case there should not be a link with connectors no 3 and 4 Otherwise the unit will not be in programming mode After you make sure the unit is in the programming mode please connect the power supply to power point The following will appear on screen as it turns on This command indicates the GSM module is working properly Peewee If the unit does not proceed to command 2 after 1 second There is Test the SIM card in the GSM module If the SIM card 1s inserted sim lee tt LL you will see a YES sign on the second line If you see NO sign on the ves TT second line please check the SIM card again and turn off the unit This command line checks if the SIM card has a PIN Pir ontrou code If there is not a PIN code you will see NO on WES TTT yy the screen and move to the next step This command checks the PIN code If you see PUN cHe FALSE please enter the correct PIN code for TRUE TT Ty the SIM card in menu 3 Please do not consider the other commands until you reach the screen shot below a problem in the GSM module Please contact your authorised agent They are for system tests iepl jusp This main screen will
7. it using connectors 3 and 4 landline or internal lines After that please disconnect the telephone device in connectors 7 and 8 subscriber lines and connect to the unit you want to work with COMPUTER CONNECTION Use the USB cable provided with the GSM dialer unit and connect one end of the cable to GD USB device and the other end to your i Yeni Donanm Bulundu X GD USB Gsm Dialer Unite computers USB port as shown in the connection diagram New Hardware wisard will apperar on the screen of your computer after you connect the cable Please insert the installation CD in your computer Select use a specified zone from the wisard and click next Gy Gna E Select Browse and choose Driver in the installation CD Installation EEOAE aba will start after you click Next After driver installation is complete right click My computer Yoni Donanim Bubamrdu Sabirbearna F i ar Hag gadiniz Properties and select device manager Please note the information in connecion settings Electrosec Comport COMX After loading the bulk SMS programme double click GD USB and run the programme The screen below will appear on you computer Click SP ice rahe port settings and choose COMX that you noted before and save You will see the communication icon flashing on the right hand side corner of the computer After that you can set the names and GSM numbers using Add Contact The important point here 1s to enter the country code at the beginning of
8. ue screen Programmable Via Subscriber line PC Input Full Speed USB 2 0 Cable Connections Screw Type Socket Thermal Protection 125C Operating Temperature 20 60 C Case Dimension 285 x 128 x 52mm Weight 980 Gr Antenna Dimension 5cm or 3mt with cable E 2009 1 electrosec Page 1 6 GD USB User s manual CONNECTION DIAGRAM son gt Pull back the Fi plastic slot on pcb and lift up amp insert your GSM sim card than push the slot back JAMMER alarm collector output Norm Emergenc Sing Baten Sa GSM Dialer Connectable alarm panel line input 12 Vdc 1A Regulated adapter T or power supply of alarm panel Landline or internal phone CONNECTIONS central line output internal phone FROM central line input LEFT to RIGHT 1 12 Vde 2 gnd 3 Landline or internal line input Tip Landi 4 Landline or internal line input Ring T P 5 Landline or internal line output Tip 6 Landline or internal line output Ring 7 Subscriber line output Tip 8 Subscriber line output Ring 9 Emergency SMS button input trigger 10 JAMMER alarm output Open coll normaly central line output Full speed USB 2 0 ISOLATION CARD CONNECTION DIAGRAM If GD USB Gsm module will be connected to a dialer unit VD 2005 TD 200 etc using an isolation card is recommended Connection diagram
9. www electrosec com 5 electrosec GD USB GSM DIALER FCT amp MULTI SMS UNIT USER S MANUAL FEATURES E Continuous Communication with Landline and GSM lines to AMS Alarm Monitoring Station amp SMS sending E Transfer via GSM data amp SMS during landline failure E Quad Band 800 900 1800 1900 Mhz GSM module E Detailed SMS sending including message title Alarm event Alarm users name and Alarm zone name E Convert to event transfer SMS for all alarm units with ADEMCO contact ID format either with or without AMS connection or disconnection E Send emergency SMS button JAMMER alarm output E FCT unit compatible for all types of internal phone unit E High Speed 2 0 USB computer input E Windows XP VISTA compatible E Automatic software upgrade on internet E MULTI SMS sending via PC control software E Read incoming SMS via PC control software E 2x16 large screen blue backlight LCD E Detailed English language program menu E Stainless steel metal case 12 Vdc input 500 mA E Dimensions 285 x 128 x 52mm Weight 980 Gr TECHNICAL SPECIFICATIONS Input voltage 12 18 Vdc Current St by 100 mA Current Active 400 mA GSM Modul Band Quad 850 900 1800 1900 MHz Gsm Band Sensitive 850 900 Mhz Typ 107dBm Gsm Band Sensitive 1800 1900 Mhz Typ 106 dBm 75 Vac 100 mA 25Hz FCT Ring Voltage FCT Subscriber Line Voltage 48Vdc 100 mA Led Screen 2x16 LCD Bl

electrosec

Contents

Download Pdf Manuals

Related Search

Related Contents