KLING & FREITAG CA 1201, CA 1215, CA 1515 User`s Manual
Contents
1. 2006 Version 3 0 22 03 2006 Page 26 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 11 Crossovers 11 1 Wiring Diagram CA 1201 The crossover networks as of the end of 2003 differ from earlier models Please com pare the crossover built into your speaker with the figures below and wire accordingly 11 1 1 Version A CA 1201 amp CA 1201 M up to serial no 231 0000 20 29 by the end of October 03 parallel with IN KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 27 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 11 1 2 Version B CA 1201 amp CA 1201 M from serial no 231 0000 20 30 as of the end of October 03 KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 28 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 11 2 Wiring Diagram CA 1215 6 and CA 1215 9 The crossover networks as of the end of 2003 differ from earlier models Please com pare the crossover built into your speaker with the figures below and wire accord inoly 11 2 1 Version A CA 1215 6 and CA 1215 6 M up to serial number 23090007055 before Sept 03 CA 1215 9 and CA 1215 9 M up to serial number 23090002675 before Sept 03 IN link to XO 2 oa 1 TTHN 7Unkto 2 24 2 8 Pin assignment Speakon NL4 ___ parallel with IN KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 29 of 51 User s2. dB Vertical coverage Attenuation dB KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 47 of 51 CA 1201 CA 1215 6 9 CA 1515 6 9 User s Manual 15 Dimensions 15 1 CA 1201 CA 1215 6 and CA 1215 9 189 3 mm 7 451 inch pole mount K amp M 19656 172 mm 6 771 inch Rigging Points ED ANCRA Jungfalk 7 211 inch 120030 31 605 mm 23 819 inch _ 378 5 mm 375 mm 189 3 mm 14 903 inch 14 763 inch 7 451 inch 5 i 61 3 mm 256 mm 2 412 inch 10 079 inch 15 2 CA 1201 M CA 1215 6 M and CA 1215 9 M 25 Eu CE 189 3 mm e x 7 451 inch Plastic Sliders Rigging Points pole mount ANCRA Jungfalk K amp M 19656 120030 31 E Ela c 8 e N E E nig _ m 174 1 mm 6 855 inch 172 mm 6 772 inch 403 mm 15 850 inch Monitor Position 61 3 mm 256 mm 2 412 inch 10 079 inch KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 48 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 15 3 CA 1515 6 and CA 1515 9 T EJE E 216 8 mm 8 536 inch Plastic Sliders pole mount Rigging Points K a
3. top of the mounted speaker is greater than 45 This maintains a permissible load on the flying points KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 13 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 5 1 Using the allsafe JUNGFALK Flying Points Single Stud Fitting Used as fastener to the allsafe JUNGFALK flying point Take the single stud fitting in one and push the locking device up hand against the spring tension 3 4 Put the flat head of the holding Release the locking device when bolt into the guiding of the flying the single stud fitting is located in point the middle of the flying point Make sure that the locking device clicks into place 5 Warning Check that the single stud fitting is securely fastened and cannot be pulled out KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 14 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 6 Coverage Patterns of the CA Speakers The mid high systems can be operated in a vertical or horizontal i e as a stage moni tor position The coverage pattern of the speakers can be adapted to special needs by a 90 rotatable horn The table below shows the coverage angles of a standing speaker To determine the coverage pattern of the high frequency horn shine a flashlight through the front covering at the level of the horn You will find a silver stripe that determines the posi tion
4. 1000WQ94 2 for speaker model CA 1515 maximum rated power 700W 8Q equivalent 1400W 4Q f you wish to use a speaker with a power amplifier which does not fulfil these spe cifications then the speaker should be controlled using a Kling amp Freitag System Controller with limiter function This is the only way overloading and that the risk of fire can be avoided The results of such a power amplifier defect of cannot be avoided by the controller 9 1 1 CA Systems in Full Range Mode This mode of operation is ideal for speech applications and music applications without the need for a high bass content Should more bass be needed the bass level can be increased between 50 and 80 Hz at the mixing console INPUT e g from mixer AUX or Connector Panel 2 1 OUTPUTS Ru CH 2 CH 1 If you are operating a mid high system in a cluster speakers arranged in close proximity or as a stage monitor reduce the frequencies below 300 Hz by 3 4 dB The K amp F C2 Controller has a special filter circuit for this purpose which can be activated with the top low cut switch KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 21 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 9 1 2 Full Range Mode amp Subwoofer with Crossover In this mode of operation you can easily realise applications where a higher bass level is needed
5. 22 03 2006 Page 7 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 2 Product Descriptions and Versions 2 1 CA 1201 Short description 2 way full range speaker system with 12 low mid chassis and 1 high frequency driver on a rotatable 90 x 60 CD horn Homogeneous coverage and constant direc tivity starting at 1 2 kHz Integrated crossover with self resetting protection circuit for low mid and high frequency path Enclosure Trapezoidal enclosure with additional cluster angles 15 mm birch plywood highly resistant structured grey or black finish internal mounting flange 5 allsate JUNG FALK flying points 2 butterfly handles highly permeable ball proof steel grille with exchangeable black acoustic foam Optional versions CA 1201 M Enclosure with additional monitor angle CA 1201 100V 100V version with 300 VA toroidal transformer CA 1201 Outdoor Installation Outdoor Mobile Versions for outdoor use under roofs CA 1201 SP Version with integrated power amplifier technology not for CA 1201 M SP speakers are shipped with a separate user s manual Special finish in RAL colours KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 8 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 2 2 CA 1215 6 Short description 2 way high performance speaker system with 12 low mid chassis and 1 5 high frequency horn driver on a rotatable 65 x 50
6. 3 results in a smaller vertical coverage angle but increases 7a 2 9 Jj Winkel 1 the sound power level Q CA 1201 with 5 1215 6 with 1215 6 1215 6 with 1215 9 1215 9 1515 6 1515 9 1515 9 Application Increasing the horizon Increasing the hori Increasing the verti tal coverage angle e g zontal coverage cal coverage angle for wide audience angle and sound e g for covering planes power level for balconies or for larger distances increased sound power level for larger distances Angle 1 Angle 2 KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 18 of 51 User s Manual Important CA 1201 CA 1215 6 9 CA 1515 6 9 The speaker is equipped with two parallel Speakon connectors Make sure that all units are switched off and all controls are turned down before con necting your CA systems We recommend the use of high quality speaker cables provided by KLING amp FREITAG A For connections to the power amplifier inputs please use 2 pin shielded microphone cable with high quality connectors A Avoid ground loops see chapter 8 2 Please pay attention to the respective pin diagrams in this manual Make sure that the polarity of the speakers at the amplifier is correct When simul taneously using power ampl
7. 5 mm 31 kg 48 monitor angle K amp F CA 1215 6 M 1100 Volt with 300 VA toroidal transformer Terminal clamps instead of Speakon connectors Outdoor Mobile and Outdoor Installation Special finish in RAL colours see catalogue or visit www kling freitag de Version 3 0 22 03 2006 Page 34 of 51 User s Manual 13 3 CA 1215 9 Loudspeaker Design Frequency range 10 dB Frequency range 3 dB Coverage angles nominal Directivity index DI Power handling Max SPL Components Crossover Impedance nominal Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 01998 2006 CA 1201 CA 1215 6 9 CA 1515 6 9 2 way passive system bass reflex tuning 58 Hz 22 kHz 80 Hz 19 kHz 90 x 50 hor x vert 10 2 1 1 kHz 13 kHz 400 W nominal 129 dB SPL Peak 1 m 12 low mid chassis 1 5 high freq driver with 75 mm titanium dome on rotatable CD horn 1 2 kHz 12 dB octave self resetting protection circuits for 12 and 1 5 chassis all pass filter for delay time and phase optimisation 8Q 2 x Speakon NLAMP 1 1 Trapezoidal with additional cluster angles 15 mm Finnish birch Multiplex with highly resistant black structured paint PU 2 butterfly handles mounting flange K amp M 19656 ball proof front grille with exchangeable black acoustic foam 5 flying points allsafe JUNGFALK 380 x 605 x 3 5 mm 31 kg 48 mon
8. CA 1201 CA 1215 6 9 CA 1515 6 9 Important Notes for the Outdoor Option Speakers with the option Outdoor Mobile and Outdoor Installation have been opti mised for outdoor use They withstand temperature fluctuations in moderate climate zones and do not accumulate condensation water In order to guarantee the longevity and safety of the speakers the speakers with the option Outdoor must still be protected from direct effects of the weather They should be installed for example under a roof so that they also have sufficient protection from driving rain from the side and direct sunlight 3 1 Outdoor Mobile Version for mobile outdoor use under roofs Features like standard version but with the following extras multi layered temperature and UV resistant high tech PU marine primer final coating with highly resistant structured 2K paint in RAL colours waterproofed diaphragms and electronic components protected against rosion with protective coating 3 2 Outdoor Installation Version for fixed outdoor installations under roofs Features like standard SWi version combined with Outdoor Mobile but with the following differences without feet and handles stainless steel thread inserts instead of flying points allsafe JUNGFALK same positions stainless steel grille foam covering behind grille visible screwed connections made of stainless steel St
9. In this mode of operation be sure to use only amplifiers which can handle speaker im pedances down to 3 Recommended combinations of CA systems as described here with K amp F subwoofers 2 CA systems 2 Ax SW 112 XO 2 x SW 115D XO 2 x SW 115E XO 1 2 x SW 118E XO Switch To XO ON Switch To XO ON INPUT e g from mixer AUX or Connector Panel d OUTPUTS 09 CH2 CH1 INPUT CH 1 INPUT CH 2 The switch XO on the connecting terminal of the subwoofer must be at XO ON for this mode of operation XO oN Ce Switch on the subwoofer s connecting terminal When using the mid high systems in a cluster speakers in close proximity reduce the frequencies below 300 Hz by 3 4 dB The K amp F C2 Controller is equipped with a special filter for this purpose which can be activated by pressing the Top Low Cut switch KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Important Page 22 of 51 User s Manual 1201 CA 1215 6 9 CA 1515 6 9 9 2 Operations with C2 Controller By using carefully adjusted filters EQ on special system cards for the CA systems the C2 Controller optimises feedback prevention and the frequency response of the spea kers The controller provides optional bass boost in full range mode optimisation for cluster operation Top Low Cut switch high boost and sub mono functions The C2 Controller optimises the op
10. Information about this User s Manual User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Version 3 0 22 03 2006 by Andr Figula Kling amp Freitag GmbH 1998 2006 all rights reserved All specifications in this manual are based on information available at the time of pub lishing for the features and safety guidelines of the described products Technical specifications measurements weights and properties are not guaranteed The manufacturer reserves the right to make product alterations within legal provisions as well as changes to improve product quality All persons who use the speaker system must have this guide and all further information for safe operations available to them during assembly disassem bly and use We appreciate any input with suggestions and improvements for this manual Please send this to us at the following address info kling freitag de or to KLING amp FREITAG GMBH Junkersstr 14 D 30179 Hannover Phone 49 0 511 96 99 70 Fax 49 0 511 67 37 94 KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 3 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Chapter Page 1 General Instructions for Using Speakers 6 2 Product Descriptions and Versions 8 2 1 1201 8 2 2 1215 6 9 2 3 1215 9 9 24 1515 6 10 2 5 1515 9 10 3 Important Notes for the Outdoor Option 11 3 1 Outdoor Mobile 11 3 2 Outdoor Installation 11 4 Notes for Versions
11. Manual CA 1201 CA 1215 6 9 CA 1515 6 9 11 2 2 Version B CA 1215 6 and CA 1215 6 M from serial number 23090007056 up as of Sept 03 CA 1215 9 and CA 1215 9 M from serial number 23090002676 up as of Sept 03 KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 30 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 11 3 Wiring Diagram CA 1515 6 and CA 1515 9 The crossover networks as of the end of 2003 differ from earlier models Please com pare the crossover built into your speaker with the figures below and wire ingly 11 3 1 Version A CA 1515 6 and CA 1515 9 up to serial number 23116000434 before November 03 ENG UR KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 31 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 11 3 2 Version B CA 1515 6 and CA 1515 9 from serial number 23116000435 as of November 03 O O IN linkto XO 2 _ IN Link to 2 LITT 12 Touching Up Damage to Paint Changing the Front Foam Although the PU structured paint used by KLING amp FREITAG is impact proof and ex tremely resistant we recommend using protective coverings or cases to help avoid damaging the paint during i e continuous mobile use If paint damage oc
12. Touching Up Damage to Paint Changing the Front Foam 32 13 Technical Specifications 33 13 1 CA 1201 33 13 2 CA 1215 6 34 13 3 CA 1215 9 35 13 4 CA 1515 6 36 13 5 CA 1515 9 37 14 Measuring Charts 38 14 1 CA 1201 38 14 2 CA 1215 6 40 14 3 CA 1215 9 42 14 4 CA 1515 6 44 14 5 CA 1515 9 46 15 Dimensions 48 15 1 CA 1201 CA 1215 6 and CA 1215 9 48 15 2 CA 1201 M CA 1215 6 M and CA 1215 9 M 48 15 3 CA 1515 6 and CA 1515 9 49 16 Accessories for the CA Systems 50 17 Regulations for Disposal 51 17 1 Germany 51 17 2 EU Norway Island and Liechtenstein not Germany 51 17 3 Other countries 51 17 Supplied Safety and Mounting Instructions for Speakers and Accessories KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 5 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 1 General Instructions for Using Speakers Mounting the speakers To prevent injury the speakers must be securely placed on the floor or secured to the wall according to the instructions on page 16 Mounting Instructions for Speakers Please note that speakers can move as a result of vibrations To prevent them from falling from their mounted position they must be secured properly If the weight of the speaker exceeds 20 kg then it is necessary for two people to carry it Warning Speakers may only be suspended or mounted to walls or ceilings by qualified personnel The speakers must be hung by using at least two of the designated flyin
13. Use high quality cables with good shielding The point of ground for all connected components should merge at one central point The power connections should lead out in a radial manner from one point and not be linked from one unit to the next When installing appliances that create strong electrostatic or electromagnetic fields large transformers switch mode power supplies maintain some distance from o ther audio appliances In extreme cases the only solution is to create a completely independent audio ground in other cases it is sufficient to connect a filter in front of the audio equipment KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 20 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 9 Configurations and Connecting Diagrams 9 1 Operating the Systems without C2 Controller The full range systems can be used alone or in conjunction with a K amp F subwoofer with integrated crossover e g SW 112 XO SW 115D XO SW 115E XO or SW 118E XO In this mode of operation the crossover limits the subwoofer s frequency range protect the speakers from being destroyed and to avoid fire hazard they should only be operated with professional power amplifiers with the following specifica tions integrated or preceding subsonic filter approx 20 Hz min 12 dB octave Warning integrated clipping limiter for speaker model CA 1201 or CA 1215 maximum rated power 500W 8Q equivalent
14. and coverage angles of the horn DEFINITION Standing speak speaker Horn not rotated Horn rotated Model CA 1201 CA 1215 6 6 1 Changing the Coverage Pattern To turn the horn follow these steps 1 Remove the four grille mounting screws on the top and bottom of the speakers with a 3 mm Allen key and remove the grille from the speaker enclosure 2 Remove the screws from the high frequency horn also using a 3 mm allen key Loosen the high frequency horn by using both hands palms to the outside to grasp into the horn and lift the horn with even pressure from the palms of your hands towards the outside Never use a screwdriver or similar objects to reach be hind the edge of the horn as this could damage it 3 Rotate the horn 90 and screw the horn on tightly again do not force it 4 Screw the grille on tightly f the coverage angle needs to be changed often make sure that the horn s not always rotated in the same direction as the connecting cables when twisted may cause the contacts of the driver to become loose KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 15 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 7 Mounting Instructions for Speakers Mount the speakers securely To avoid injury or damage always be sure to mount the speakers securely so that they do not fall Speakers which are stacked must be secured with securing straps When laying the
15. balanced sound to music programmes When using the mid high systems in a cluster speakers in close proximity or as a stage monitor activate the Top Low Cut switch on the C2 Controller KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 24 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 9 2 2 CA System amp Bass with Controller C2 in 2 Way Active Mode For using Subwoofers with XO set switch bn back to XO OFF ALL SPEAKONS 1 1 KING amp r 9 DIS DID o 240V 50 oJ Orbe FUSE 100mA SLOW REMOTE CONTROL OPTIONAL REMOTE gt UNIT a _ ________ _ AMP MID HIGH pid ps il 92 69 iz C O BASS CH2 pe CH p CH2 Os The switch XO on the connecting terminal of the subwoofer must be at OFF for this mode of operation XO Switch on the subwoofer s connecting terminal Note for the full range mode The countersunk switch Full Range Mode on the C2 Controller should not be pressed and the LED assigned to it should not light up Note for clustered configurations When using the CA systems in a cluster speakers in close proximity activate the Top Low C
16. connecting cables make sure that nobody can trip The stability of stacked systems also valid for the use of stands and distance rods is Warning contingent upon the following stability requirement These conditions must therefore be guaranteed by the user Stacked systems may not fall over even if they are inclined by 10 in each direction If this requirement is not fulfilled then it is necessary to take steps to achieve compliance Possible measures include strapping it to an appropriate base struc ture or fastening it using safety straps 7 1 Proper Arrangement of the Loudspeakers Be aware of the fact that the logical targeted alignment of this high quality speaker system can lead to a significant qualitative increase in the acoustic result It is not possi ble to make generalities about the alignment of specific systems because the room has a substantial influence on the signal and the audible result As a rule the mid and high transducers of loudspeakers should be mounted above the audience s face value so that the sound distribution cannot be shadowed In many cases it is advisable to mount a loudspeaker higher so that the sound will be distributed throughout the room more evenly Low standing systems result in a greater difference in volume between front and back seats than higher standing systems Please note that this is only a general guideline and the best possible result may vary from room to room To simulate
17. of 51
18. often connected to the protective earth connector PE Ground If two or more units are connected to one another with a line level audio cable there may be a ground connection through the ground of the power supply cable yellow green as well as through the shielding of the audio cable The voltage difference between these two ground points causes audible interference to come from the speaker 8 2 2 Avoiding Ground Loops If there is a loud humming or buzzing after the CA System has been connected then check that a ground loop has not been built into the system Some power amplifiers and system controllers are equipped with a Ground Lift switch Set these switches to the Lift position one after the other If the noise is still audible check if 1 the noise is caused by a ground loop before the power amplifiers controllers e g mixing console effects or equalizers 2 the system or parts of the system are connected to an unclean power supply meaning one which is also running large motors or lighting systems An un clean supply voltage electrostatic and electromagnetic fields can cause a mal function Please observe the following basic rules Never try to avoid a ground loop by disconnecting or taping the ground contact at the power connector Extremely dangerous Warning f possible only use high quality audio appliances with balanced signal outputs and with power cables with PE connectors
19. with 100V Option 12 4 1 Reasons for choosing Speakers with 100 V Transformers 12 4 2 Connecting Diagram of the 100V Speaker Inputs 12 5 Instructions for Suspending the Speakers 13 5 1 Using the allsafe JUNGFALK Flying Points 14 6 Coverage Patterns of the CA Speakers 15 6 1 Changing the Coverage Pattern 15 7 Mounting Instructions for Speakers 16 7 1 Proper Arrangement of the Loudspeakers 16 7 2 Arrayed Speaker Systems Cluster 17 7 2 1 Horn not rotated 17 7 2 2 With rotated Horn 18 8 Wiring 19 8 1 Connecting the Speakon Connector to the Terminal 19 8 2 Avoiding Ground Loops 20 8 2 1 What is a Ground Loop 20 8 2 2 Avoiding Ground Loops 20 9 Configurations and Connecting Diagrams 21 9 1 Operating the Systems without C2 Controller 21 9 1 1 CA Systems in Full Range Mode 21 9 1 2 Full Range Mode amp Subwoofer with Crossover XO 22 9 2 Operations with C2 Controller 23 9 2 1 Full Range Mode with C2 Controller 24 9 2 2 CA System amp Bass with Controller C2 in 2 Way Active Mode 25 10 Operating the Speakers 26 KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 4 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Chapter Page 11 Crossovers 27 11 1 Wiring Diagram CA 1201 27 11 1 1 Version A 27 11 1 2 Version B 28 11 2 Wiring Diagram CA 1215 6 and CA 1215 9 29 11 2 1 Version A 29 11 2 2 Version B 30 11 3 Wiring Diagram CA 1515 6 and CA 1515 9 31 11 3 1 Version A 31 11 3 2 Version B 32 12
20. 0 10000 20000 Frequency Hz Frequency response 110 SPL dB Impedance Ohm o Horizontal Beamwidth 360 300 5 240 s lt 180 120 49 i c 60 0 20 100 1000 10000 20000 Frequency Hz 20 Directivity Index DI dB Directivity Factor Q 1 20 100 1000 10000 20000 Frequency Hz KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 42 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Horizontal coverage Attenuation dB Vertical coverage Attenuation dB KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 43 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 14 4 CA 1515 6 Frequency response Impedance ee lee LLLI LEE U C r I LLLI OA ___ _ NAIN Lal Frequency response SPL dB Impedance Ohm 20 100 1000 10000 20000 Frequency Hz Horizontal us Beamwidth sedie App cal I NAC TT T LL LLLLHIL _ 300 j j jj d __ ___ 240 j 4 JM EET 180 _ ___ 120 5 __ 60 Ne 1 1 gt 0 _____ j If E 1 114 20 100 1
21. 000 10000 20000 Frequency Hz 20 Directivity Index DI dB o Directivity Factor Q O LL T p s I 20 100 1000 10000 20000 Frequency Hz KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 44 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Horizontal coverage Attenuation dB f Hz Attenuation dB KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 45 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 14 5 CA 1515 9 Frequency response Frequency response Impedance HR 100 SPL dB Impedance Ohm NEN 10 s 20 100 1000 10000 20000 Frequency Hz Horizontal A Vertical 300 6dB Beamwidth degrees 20 100 1000 10000 20000 Frequency Hz 20 __ LLL j O HU i 05027 LIII ___ 7 __ LLLI ___ ___ uL LLLI Directivity Factor Q Directivity Index DI dB o _ j 20 100 1000 10000 20000 KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 46 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Horizontal coverage 150 Attenuation
22. 110372 For the German Registration office EAR we have accredited that our products are sole B2B products 17 2 Norway Island and Liechtenstein not Germany It is not allowed to dispose of used electrical equipment as domestic waste The Kling amp Freitag AG has thus labelled all products coming from EU Member coun tries as well as Norway Island and Liechtenstein except Germany mentioned in the WEEE from 08 13 2005 onwards with a sign with a crossed out waste bin and a white bar below This sign indicates that the disposal into the domestic waste is prohibited and that the product has been put into circulation at the 08 13 2005 earliest Unfortunately the European directive WEEE has been complied with implementing dif ferent national provisions of law throughout all member countries which makes it im possible for us to offer consistent solutions for the disposal throughout Europe Responsible for complying with these provisions of law is the local distributor importer of each country For proper disposition of used products in accordance with these local provisions in the mentioned countries of the European Union except Germany please ask your local dealer or the local authorities 17 3 Other countries For proper disposition of used products in accordance with local provisions in other countries please ask your local dealer or the local authorities KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 51
23. CD horn Homogeneous coverage and constant directivity starting at 1 2 kHz Integrated crossover with self resetting protec tion circuit for high frequency path delay time and phase optimisation Enclosure Trapezoidal enclosure with additional cluster angles 15 mm birch plywood highly resistable structured grey or black finish internal mounting flange 5 allsate JUNG FALK flying points 2 butterfly handles highly permeable ball proof steel grille with exchangeable black acoustic foam Optional versions CA 1215 6 M Enclosure with additional monitor angle CA 1215 6 100V 100V version with 300 VA toroidal transformer CA 1215 6 Outdoor Installation Outdoor Mobile Versions for outdoor use under roofs CA 1215 6 SP Version with integrated power amplifier technology not for CA 1215 6 M SP speakers are shipped with a separate user s manual Special finish in RAL colours 2 3 CA 1215 9 Short description 2 way high performance speaker system with 12 low mid chassis and 1 5 high fre quency driver on a rotatable 90 x 50 CD horn Homogeneous coverage and con stant directivity starting at 1 0 kHz Integrated crossover with self resetting protection circuit for high frequency path delay time and phase optimisation Enclosure Trapezoidal enclosure with additional cluster angles 15 mm birch plywood highly resistant structured grey or black finish internal mounting flange 5 allsaf
24. KLING amp FREITAG 1201 CA 1215 CA 1515 Version 3 0 Released 22 03 2006 a ad 88 PE FREITAG AX 0 049 67 37 94 SOUND SYSTEMS User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 2 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Thank you for your decision to buy a KLING amp FREITAG product To guarantee a trouble free operating of the equipment and to enable the KLING amp FREITAG CA speaker system to achieve its full potential please read the operating instructions carefully before use With the purchase of a CA system you have acquired a speaker system with the highest possible quality and performance capabilities As the owner of this system you now have a versatile and highly professional tool which when operated properly is a true pleasure to use Symbols in User s Manual This symbol indicates the possibility of life threatening danger and a health risk for persons Not following these instructions may result in serious health problems including potentially fatal injuries Warning This symbol indicates a possibly dangerous situation Not following these instructions may cause minor injuries or cause property damage Caution This symbol gives instructions for the proper use of the described prod ucts Not following these instructions may cause malfunctions or prop erty damage Important
25. LK 380 x 605 x 375 mm 25 kg 48 monitor angle K amp F CA 1201 M 1100 Volt with 300 VA toroidal transformer Terminal clamps instead of Speakon connectors Outdoor Mobile and Outdoor Installation Special finish in RAL colours see catalogue or visit www kling freitag de Version 3 0 22 03 2006 Page 33 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 13 2 CA 1215 6 Loudspeaker Design Frequency range 10 dB Frequency range 3 dB Coverage angles nominal Directivity index DI Power handling Max SPL Components Crossover Impedance nominal Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 1998 2006 2 way passive system bass reflex tuning 62 Hz 22 kHz 84 Hz 19 kHz 65 x 50 hor x vert 12 1 5 2 1 2 kHz 16 kHz 400 W nominal 130 dB SPL peak 1 m 12 low mid chassis 1 5 high freq driver with 75 mm titanium dome on rotatable CD horn 1 2 kHz 12 dB octave self resetting protection circuits for 12 and 1 5 chassis all pass filter for delay time and phase optimisation 8 Q 2 x Speakon NLAMP 1 1 Trapezoidal with additional cluster angles 15 mm Finnish birch Multiplex with highly resistant black structured paint PU 2 butterfly handles mounting flange K amp M 19656 ball proof front grille with exchangeable black acoustic foam 5 flying points allsafe JUNGFALK 380 x 605 x 3
26. VA toroidal transformer CA 1515 6 Outdoor Installation Outdoor Mobile Version for outdoor use under roofs 1515 6 SP Version with integrated power amplifier technology SP speakers are shipped with a separate user s manual Special finish in RAL colours 2 5 CA 1515 9 Short description 2 way high performance speaker system with 15 low mid chassis and 1 5 high fre quency driver on a rotatable 90 x 50 CD horn Homogeneous coverage and constant directivity starting at 1 0 kHz Integrated crossover with self resetting protection circuit for chassis and crossover delay time and phase optimisation Enclosure Trapezoidal enclosure with additional monitor and cluster angles 15 mm birch ply wood highly resistant structured grey or black finish internal mounting flange 5 all safe JUNGFALK flying points 2 butterfly handles highly permeable ball proof steel grille with exchangeable black acoustic foam non abrasive plastic feet Optional versions 1515 9 100V 100V version with 300 VA toroidal transformer 1515 9 Outdoor Installation Outdoor Mobile Version for outdoor use under roofs CA 1515 9 SP Version with integrated power amplifier technology SP speakers are shipped with a separate user s manual Special finish in RAL colours KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 10 of 51 User s Manual Warning
27. ainless steel connecting terminal with single PG cable fitting 13mm Connector bl blue bn brown KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 11 of 51 User s Manual 4 Notes for Versions with 100V Option Kling amp Freitag speakers with 100V option are fitted with high quality toroidal trans formers This serves to minimize loss of sound Highly professional sound reinforcement results can be achieved using 100 V Kling amp Freitag speakers 4 1 Reasons for choosing Speakers with 100 V Transformers Reduction in conduction loss Easy installation of a loudspeaker network due to simple parallel wiring The sum of the output power of the individual speakers stated as VA W must not exceed the output power of the 100 V amplifier Speakers are galvanically isolated Speakers can be integrated into existing 100 V systems 4 2 Connecting Diagram of the 100V Speaker Inputs 300VA transformer 0 all pins parallel to out KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 CA 1201 CA 1215 6 9 CA 1515 6 9 Important Page 12 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 5 Instructions for Suspending the Speakers The speakers may only be suspended by trained specialised personnel Pay attention to the required safety factors Please follow the accompanying safety and assembly instructions carefully as well as the corresponding national safe
28. curs despite these precautions it can be touched up by using commercial acrylic paint in the appro priate RAL colour of the speaker To replace the filter foam send the front grille incl foam to KLING amp FREITAG GmbH Upon payment for expenses the grille with the new covering will be returned KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 32 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 13 Technical Specifications 13 1 CA 1201 Loudspeaker Design Frequency range 10 dB Frequency range 3 dB Coverage angles nominal Directivity index DI Power handling Max SPL Components Crossover Impedance nominal Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 01998 2006 2 way passive system bass reflex tuning 54 Hz 19 kHz 65 Hz 18 kHz 90 x 60 hor x vert 10 1 5 1 1 2 kHz 16 kHz 300 W nominal 126 dB SPL peak 1 m 12 low mid chassis 1 high freq driver with 40 mm titanium dome on rotatable CD horn 1 8 kHz 18 dB octave self resetting protection circuits for 12 and 1 chassis 8Q 2 x Speakon NLAMP 1 1 Trapezoidal with additional cluster angles 15 mm Finnish birch Multiplex with highly resistant black structured paint PU 2 butterfly handles mounting flange K amp M 19656 ball proof front grille with exchangeable black acoustic foam 5 flying points allsafe JUNGFA
29. dB lt 3 6 6 9 9 12 12 15 B 15 18 18 Page 39 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 14 2 CA 1215 6 Frequency response Frequency response Impedance 110 100 100 _ _ E 7702 90 31 66 8 A 5 e 80 0 70 3 16 20 100 1000 10000 20000 Frequency Hz B dih Horizontal PATE Vertical 360 300 5 240 5 180 O 120 E 60 tb 1 0 20 100 1000 10000 20000 Frequency Hz Directivity 20 100 D g __ __ __ ____ 5 OQ r 10 ZO O oO 10 amp Aoo S r T E 5 E E B a We 1 111 _ d LLLI 20 1000 10000 20000 Frequency Hz KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 40 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Horizontal coverage Attenuation dB Attenuation dB KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 41 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 14 3 CA 1215 9 Frequency response Impedance U A M soc Y of tit TT TT A a T CN LAC e Ill Ill daas 20 100 100
30. e JUNG FALK flying points 2 butterfly handles highly permeable ball proof steel grille with exchangeable black acoustic foam Optional versions CA 1215 9 M Enclosure with additional monitor angle CA 1215 9 100V 100V version with 300 VA toroidal transformer CA 1215 9 Outdoor Installation Outdoor Mobile Version for outdoor use under roofs CA 1215 9 SP Version with integrated power amplifier technology not for CA 1215 9 M SP speakers are shipped with a separate user s manual Special finish in RAL colours KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 9 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 2 4 CA 1515 6 Short description 2 way high performance speaker system with 15 low mid chassis and 1 5 high fre quency driver on a rotatable 65 x 50 CD horn Homogeneous coverage and con stant directivity starting at 1 2 kHz Integrated crossover with self resetting protection circuit for chassis and crossover delay time and phase optimisation Enclosure Trapezoidal enclosure with additional monitor and cluster angles 15 mm birch ply wood highly resistant structured grey or black finish internal mounting flange 5 allsafe JUNGFALK flying points 2 butterfly handles highly permeable ball proof steel grille with exchangeable black acoustic foam non abrasive plastic feet Optional versions CA 1515 6 100V 100V version with 300
31. er The Sense LED for the top speaker i e CH 1 TOP signal of the C2 Controller will light up green at a level of at ca A0dB The other channels of the system are checked in the same way If the wrong LED lights up or a wrong i e in 2 way active mode low signal from a high frequency speaker or distorted signal occurs then there is a mistake in the wiring Your system should now be ready for operation Turning down the input level controls may not always prevent distortions in the input section of the power amplifier especially if this section has a relatively low headroom A clipping signal may not be displayed by the clipping indicator then To prevent sig nal interruptions or damages to the speakers turn the level controls of the power amplifier to the maximum position if possible The output level of the mixing console or the controller should be set to a level that doesn t overload the power amplifiers When turning off the system the input controls for the power amplifiers should be turned down first followed by the power switches of the amplifiers After that the other appliances can be turned off The crossovers of the CA systems are equipped with protection circuits for the high frequency driver and the crossover itself These circuits cut off the signal current when highly overloaded If the high speaker turns off reduce the volume After a few sec onds it will turn back on automatically KLING amp FREITAG GMBH 1998
32. erating safety of the speakers and power amplifiers by using special peak and RMS limiters in sense technology With other universal controllers the gain of the selected power amplifiers must be known The limiter on the C2 Controller on the other hand uses a special control circuit to determine the actual output voltage of the power amplifiers The limiter then reduces the input level only when the power amplifier actually provides more power than the speakers can handle The amplifier s gain and the position of the input level control for the power amplifiers are insignificant for the limiter function of the C2 Controller C2 Power amplifier with Controller Measured value output voltage of the power amplifier Universal Power amplifier with Controller input level control Fixed value depending on the amplifier s gain and the position of the input level control of the power amplifier KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 23 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 9 2 1 Full Range Mode with K amp F C2 Controller ALL SPEAKONS Front View 1 1 Rear View OPTIONAL REMOTE gt UNIT The countersunk switch Full Range Mode on the C2 Controller should be pressed and the LED assigned to it should light up The full range switch accentuates the bass fre quencies of the mid high systems giving a more
33. g points The same applies when lifting and aligning the speakers Never use signal cables or power cords for suspending aligning or securing the systems When laying the connecting cables make sure that nobody can trip Never hang more than two speakers under one another without using the designated Kling amp Freitag rigging equipment Ensure that all installation connections comply with the applicable safety guidelines and that the size and strength are sufficient Further instructions are in our user s manual for assembly equipment and in the general safety instructions for speakers and assembly equipment For mobile and fixed installations use only rigging equipment from KLING amp FREITAG Make sure to observe the included safety and mounting instructions for loudspeakers and accessories Speakers and rigging equipment must be visually examined at regular intervals If there are signs of wear they must be replaced immediately Furthermore screwed connections of supporting parts must be checked routinely Protecting the speakers avoiding fire hazard In general audio signals should not be overdriven This may be caused by mixing consoles equalizers effect equipment etc and should be indicated on this equipment When a power amplifier is overloaded at the output clipping then the amplifier should activate a clipping warning signal Power amplifiers can also be overloaded at the input circuit without the amplifier signalling t
34. g points for recycling either All Kling amp Freitag products are plain business to business B2B products Disposal of Kling amp Freitag products labelled with a waste bin sign have thus to be disposed of by Kling amp Freitag alone Please call Kling amp Freitag at the number stated below if you have a Kling amp Freitag product to be disposed We will offer you a straightforward and pro fessional disposal not affecting costs If there is no dustbin sign on one of your Kling amp Freitag products because they have been sold before March 2006 then by law the owner is in charge of the disposal For these we will be happy to assist and offer you proper ways of disposal Telephone number to call about the disposal of used Kling amp Freitag products 49 511 96 99 7 0 Explanation With the ElektroG law relating to electrical and electronic equipment and appliances we have complied with the EU directive on waste electrical and electronic equipment WEEE 2002 96 EC The Kling amp Freitag AG has thus labelled all products mentioned in the WEEE from 03 24 2006 onwards with a sign with a crossed out waste bin and a white bar below This sign indicates that the disposal into the domestic waste is prohibited and that the product has been put into circulation at the 03 24 2006 earliest The Kling amp Freitag GmbH has been legally registered as a manufacturer with the regis tration office EAR Our WEEE Registration Nr is DE64
35. he clipping i e when there is not sufficient headroom in the input cir cuit We therefore recommend turning up the power amplifiers all the way and adjusting the level before the power amplifier in order to avoid overloading the input circuit In any case the signal must be reduced as soon as it sounds unnaturally distorted protect the speakers from being destroyed and to avoid fire hazard they should only be operated with professional power amplifiers with the following specifications Integrated or preceding subsonic filter approx 20 Hz min 12 dB octave integrated clipping limiter for speaker models CA 1201 or CA 1215 Warning maximum rated power 500W 8Q equivalent 1000W 4Q for speaker model CA 1515 maximum rated power 700 equivalent 1400W 4Q f you wish to use a speaker with a power amplifier which does not fulfil these specifica tions then the speaker should be controlled using a Kling amp Freitag system controller with limiter function This is the only way overloading and that the risk of fire can be avoided The results of such a power amplifier defect of cannot be avoided by the con troller f power amplifiers have power ratings lower than mentioned above then it is impera tive that a clipping limiter is used to protect the speaker even if it is used with a Kling amp Freitag system controller For damage caused by overloading or use with power amplifiers other than t
36. hose rec ommended above Kling amp Freitag GmbH does not assume warranty and excludes liability for possible consequential damage Important KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 6 of 51 User s Manual Important Cautiomn CA 1201 CA 1215 6 9 CA 1515 6 9 The following signals may damage the speakers Permanent high pitched signals with high frequency and continuous noise from feedback Permanently distorted signals with high power Noises which occur when the amplifier is on while equipment is being con nected disconnected or switched on Do not install speakers in any of the following places Where the speakers are permanently exposed to direct sunlight Where the speakers are exposed to high moisture Where the speakers are exposed to strong vibrations and dust Damage caused by the speakers magnetic fields Speakers are permanently surrounded by a magnetic field even when they are not operating Therefore during transport and placement of the speakers it is important to ensure that there is always approx 1 m between the speakers and magnetic data media and computer video monitors Preventing hearing damage To prevent the risk of hearing damage avoid being too close to operating speakers even if the volume level seems to be low enough In general volume levels over 90 dB can cause hearing damage KLING amp FREITAG GMBH 01998 2006 Version 3 0
37. ifiers from different manufacturers be sure to use the correct specific pin configuration It may be necessary to modify the pin configuration on the power amplifiers or on the connectors leading to them Upon completing the wiring ensure that the connected speaker channels are work ing in phase To do so use i e a phase checker A phase error can also be recognized when the connected channels are used simultaneously During simultaneous use the bass frequencies become notably quieter or the mid frequencies such as voices can not be located To avoid loss of power the cables should have a minimum wire gauge of 2 5 mm more for longer cabled distances A minimum wire gauge can be easily calculated with the following formula Minimum Wire Gauge mm Required Cable Length m 2 x Speaker Impedance If several loudspeakers are connected the signal can be linked through from one loud speaker to the next Please make sure that the total impedance of the loudspeakers R Q is not lower than the minimal impedance indicated on the power amplifier VR 1 R 1 8 1 R total 8 1 Connecting the Speakon Connector to the Terminal KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 19 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 8 2 Avoiding Ground Loops 8 2 1 What is Ground Loop Every component of a P A or Hi Fi System has its own internal 0 V reference ground This point is
38. itor angle K amp F CA 1215 9 M 1100 Volt with 300 VA toroidal transformer Terminal clamps instead of Speakon connectors Outdoor Mobile and Outdoor Installation Special finish in RAL colours see catalogue or visit www kling freitag de Version 3 0 22 03 2006 Page 35 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 13 4 CA 1515 6 Loudspeaker Design Frequency range 10 dB Frequency range 3 dB Coverage angles nominal Directivity index DI Power handling Max SPL Components Crossover Impedance nominal Connectors Enclosure Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 1998 2006 2 way passive system bass reflex tuning 47 Hz 22 kHz 77 Hz 19 kHz 65 x 50 hor x vert 12 1 5 2 1 2 kHz 16 kHz 500 W nominal 132 dB SPL peak 1 m 15 low mid chassis 1 5 high freq driver with 75 mm titanium dome on rotatable CD horn 1 1 kHz 12 dB octave self resetting protection circuits for speakers and crossover all pass filter for delay time and phase optimisation 8 Q 2 x Speakon NLAMP 1 1 Multi purpose enclosure with monitor and cluster angles 15 mm Finnish birch Multiplex with highly resistant black structured paint PU 2 butterfly handles mounting flange K amp M 19656 ball proof front grille with exchangeable black acoustic foam 433 x 680 x 410 mm 36 4 kg 1100 Volt with 300 VA toroidal transformer Terminal c
39. lamps instead of Speakon connectors Outdoor Mobile and Outdoor Installation Special finish in RAL colours see catalogue or visit www kling freitag de Version 3 0 22 03 2006 Page 36 of 51 User s Manual 13 5 CA 1515 9 Loudspeaker Design Frequency range 10 dB Frequency range x3 dB Coverage angles nominal Directivity index DI Power handling Max SPL Components Crossover Impedance nominal Connectors Enclosure Rigging Dimensions W x H x D Weight Options Accessories KLING amp FREITAG GMBH 01998 2006 CA 1201 CA 1215 6 9 CA 1515 6 9 2 way passive system bass reflex tuning 58 Hz 22 kHz 75 Hz 19 kHz 90 x 50 hor x vert 10 2 1 1 kHz 13 kHz 500 W nominal 131 dB SPL peak 1 m 15 low mid chassis 1 5 high freq driver with 75 mm titanium dome on rotatable CD horn 1 1 kHz 12 dB octave self resetting protection circuits for speakers and crossover all pass filter for delay time and phase optimisation 8Q 2 x Speakon NLAMP 1 1 Multi purpose enclosure with monitor and cluster angles 15 mm Finnish birch Multiplex with highly resistant black structured paint PU 2 butterfly handles mounting flange K amp M 19656 ball proof front grille with exchangeable black acoustic foam 5 flying points allsate JUNGFALK 433 x 680 x 410 mm 36 4 kg 1100 Volt with 300 VA toroidal transformer Terminal clamps instead of Speakon connectors Outdoor Mobile a
40. mp M 19656 ANCRA Jungfalk 120030 31 i T ES e Ele Elo m m m 9 433 6 mm 411 3 mm 212 3 mm Bo rm Li 17 073 inch 16 195 inch 8 358 inch 189 5 mm 7 461 inch 454 mm 17 890 inch Monitor Position 62 9 mm 307 8 mm 2 476 inch 12 120 inch KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 49 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 16 Accessories for the CA Systems Adjustable speaker mount CA 1201 CA1215 Cradle 1201 CA1215 Adjustable speaker mount CA 1515 Cradle 1515 C lt gt C XX IN 2 ZZ Multi Cradle CA 1201 CA1215 Wall mount Multi Cradle CA 1515 tiltable up to 50 kg adjustable speaker mount mounting adapter distance rod g Distance rod amp application examples with TV style damp TV spigot single stud adjustable speaker mount fitting Further information is available in our downloadable catalogue at www kling freitag de KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 50 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 17 Regulations for Disposal 17 1 Germany It is not allowed to dispose of used electrical equipment as domestic waste But please do not dispose of them at official collectin
41. nd Outdoor Installation Special finish in RAL colours see catalogue or visit www kling freitag de Version 3 0 22 03 2006 Page 37 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 14 Measuring Charts 14 1 CA 1201 Frequency response Impedance ie I NS d ss x LLLI ZOS ATL STIL T LAL 20 100 1000 10000 20000 Frequency Hz Frequency response 110 SPL dB Impedance Ohm Horizontal Beamwidth A Vertical 360 doo C SSN __ d ___ doo ___ ___ Nac de ee ___ T PPM N 1 d l1 CIN 20 100 1000 10000 20000 Frequency Hz UJ e e N e N O e 6dB Beamwidth degrees e 20 e Directivity Index DI dB Directivity Factor Q 20 100 1000 10000 20000 Frequency Hz KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 38 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 Horizontal coverage Vertical coverage 180 150 120 KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Attenuation dB lt 3 3 6 16 9 9 12 12 15 15 18 L gt 18 Attenuation
42. the correct alignment of the speakers beforehand there are various pro grams such as Ease or Ulysses The Kling amp Freitag speaker system data is available for download on our website www kling freitag de The following graphics will assist in making a rough estimate as to the distance range of full range systems The graphics only take into consideration the sum of the direct sound and not the influence of the room Because of this there can in some cases be noticeable deviation Distance range of SPL direct sound level 18 dB 12 dB 6 dB 24 30 oT 34 tt T T T 2m 4m am 16m 32m 50m KLING amp FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 16 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 7 2 Arrayed Speaker Systems Cluster If the loudspeakers are operated through the optional K amp F C2 System Controller we recommend to turn on the Top Low Cut switch for clustered operation Thus the fre quency response for this application can be optimised see also K amp F C2 user s manual When operating the systems without the C2 System Controller in a clustered con figuration the signal level of frequencies below 300 Hz should be reduced by 3 4 7 2 1 Horn not rotated Winkel 2 gt Winkel 3 Horn not rotated Standing speaker Winkel 1 A smaller angle 3 results in a smaller
43. ty regulations Warning Speaker systems whether single or connected to one another must always be secured to a second separate point even if two rigging points are used for suspending the speaker system Ensure that all connections are secured to prevent their detaching on their own and that only admissible statically tested and sufficiently sized connecting devices ropes and chains are used A maximum load of 50 kg may be suspended from the two allsafe JUNGFALK flying points of one speaker This means a maximum additional load of 25 kg on each allsafe JUNGFALK flying point Wrong The suspended speaker weighs more than 50 kg This exceeds the total load bearing capacity of the upper flying points As result a maxi mum of 2 full range systems be sus pended under one another The rear suspension point can only support weights up to 30 kg The flying point is thus not an appropriate secondary device to prevent collapse if another speaker is mounted The angle of the rope chain in relation to the top of the mounted speaker is less than 452 This causes the load on the flying points to ex ceed the permissible level Right two point suspension was selected Each speaker is secured with an additional safety de vice The suspended speaker weighs no more than 50 kg This falls within the total load bearing capacity of the upper flying point The angle of the rope chain in relation to the
44. ut switch on the C2 Controller KLING FREITAG GMBH 1998 2006 Version 3 0 22 03 2006 Page 25 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 10 Operating the Speakers Switch off all equipment and turn down all level controls Wire the CA systems according to the wiring diagrams as shown before Upon completing the wiring ensure that the connected speaker channels are working in phase To do so use i e a phase checker A phase error can also be recognized when the connected channels are used simultaneously During simultaneous use the bass frequen cies become notably quieter or the mid frequencies such as voices cannot be located Now switch on the peripheral equipment first mixing console effects etc followed by the C2 Controller if used and the power amplifiers Always use the before mentioned switching order Otherwise switching noises may damage the system If there is interference turn off all appliances in the reverse order and check all cable connections see chapter 8 2 I tant mportan Next turn on the C2 Controller if used and the other peripheral equipment and make sure there is no interference Now put a low level signal into the system and check for the correct function of the system In doing so all amplifier input controls need to be turned off again Now turn on the control for the left CA system and check that the correct signal is coming out of the CA system With C2 Controll
45. vertical coverage angle but increases the sound power level between the sides of the speakers Combination CA 1201 with 45 55 55 65 CA 1201 not generally not generally 20 35 recommended recommended CA 1215 6 with 1215 6 1215 6 with CA 1215 9 CA 1215 9 with 40 50 50 60 CA 1215 9 not generally not generally recommended recommended CA 1515 6 with 20 30 1515 6 CA 1515 6 with o CA 1515 9 CA 1515 9 with 409 5029 509 609 CA 1515 9 not generally not generally recommended recommended Application Increasing the horizon Increasing the Increasing the vertical tal coverage angle e g horizontal cover coverage angle e g for wide audience age angle and for covering balco planes sound power level nies or for increased for larger dis sound power level tances for larger distances f several 90 systems are clustered unwanted interference effects may appear As a result we do not generally recommend clustered configurations of CA 1201 CA 1215 9 and CA 1515 9 systems If wide angles are to be covered we recommend the use of several 60 or 65 systems in one cluster KLING amp FREITAG GMBH 01998 2006 Version 3 0 22 03 2006 Page 17 of 51 User s Manual CA 1201 CA 1215 6 9 CA 1515 6 9 7 2 2 With rotated Horn Winkel 2 Winkel 3 Horn rotated Standing speaker A smaller angle
Download Pdf Manuals
Related Search