USER MANUAL - AV-iQ
Contents
1. To connect the 622T Dual Link DVI Optical Transmitter with the 622R Dual Link DVI Optical Receiver as the example in Figure 4 illustrates do the following 1 Connect the DVI source for example a set top box to the 622T DVI IN connector using the dual link DVI copper cable Make sure that the system is not powered up when connecting the DVI source 2 On the 622R connect the DVI OUT connector to the DVI acceptor for example a display using the dual link DVI copper cable 3 Remove the module dust covers and connect each duplex LC fiber cable one by one to each of the eight LC receptacles of the 622T and 622R 4 Carefully recheck the polarities and ensure that the duplex connectors are fully engaged 1 Switch OFF the power on each device before connecting it to your 622T and 622R After connecting your 622T and 622R switch on its power and then switch on the power on each device 2 Alternatively you could connect a computer or other DVI source 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Using the Dual Link DVI Optical Transmitter Receiver Do not look directly into the LC receptacles of the 622T while powered on although this product is regulated strictly enough to operate under the Laser Class 1 classified by CDRH FDA for eye safety 5 Connect the DDC RJ 45C connector on the 622T to the DDC RJ 45C connector on the 622R via UTP cabling see section 5 3 6 Connect the 12V 2 1A DC power adapte2. Feature Function 1 LINK DUAL LED Lights when the second link is present 2 SINGLE LED Lights when the first link is present 3 POWER LED llluminates when receiving power 4 D CL1 CL2 Connects to the clock connectors on the 622T 5 8 R2 G2 6 2 B2 R1 Connect to the optic connectors on the 622T 7 6 ais 8 DDC CATS5 Connector Connects to the DDC Ru 45 connector on the 622T 9 DVI OUT Connector Connects to the DVI acceptor 10 12VDC 12V DC connector for powering up the unit 1 Using a UTP CATS cable with RJ 45 connectors at both ends the PINOUT is defined in Table 3 and Figure 5 5 Using the Dual Link DVI Optical Transmitter Receiver 5 Using the Dual Link DVI Optical Transmitter Receiver You can use the 622T and 622R to configure a dual link optical transmitter and receiver system as illustrated in Figure 3 the source connects to the 622T the 622R connects to the display and both transmitter and receiver are interconnected via fiber optics and UTP cabling Optic Fiber Cables up to 100 meters 622T 622R Transmitter Receiver Figure 3 622T and 622R Dual Link DVI Optical Transmitter and Receiver System DDC Cabling up to 100 meters It is recommended to test your system configuration by first connecting the entire system as illustrated in Figure 3 using short copper cables instead of optical fiber cables 5 1 Connecting the 622T 622R
3. 0825 1 Complies with the limits for a Class A digital device pursuant to part 15 and 2 of FCC and CE Does not require any special memory size CPU speed and chipsets when using a computer Is backward compatible with the DVI 1 0 standard 1 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 2 Extended Display Identification Data 3 High Bandwidth Digital Content Protection 4 Using DDC Digital Display Channel the display can inform the video card about its properties such as the maximum resolution and the color depth The video card can then use this information to ensure that you are presented with valid options for configuring the display KRAMER SIMPLE CREATIVE TECHNOLOGY Your Dual Link DVI Optical Transmitter Receiver 3 ont To achieve the best performance e Connect only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances and position your Kramer 622R and 622T away from moisture excessive sunlight and dust Power Connect Feature The Power Connect feature lets you power a transmitter receiver system by connecting just one power adapter to either the transmitter or the receiver The other unit is fed over the same CATS cable The Power Connect feature applies as long as the
4. CATS cable is heavy gauge cable that is it can carry power The distance does not exceed 50 meters on standard cable For a distance of 100 meters separate power supplies must be connected to the transmitter and to the receiver simultaneously unless using heavy gauge CATS cable 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP The decision whether to use shielded twisted pair STP cable or unshielded twisted pair UTP cable depends on the nature of the application It is recommended that in applications with high interference shielded twisted pair STP cable will give better results However the shield itself does create a capacitance that degrades the frequency response of the machines For shorter distances of 50m or so shielded twisted pair STP cable is preferred because it provides protection from interference degradation is non apparent For a long range application unshielded twisted pair UTP cable is preferred However the unshielded twisted pair UTP cable should be installed far away from electric cables motors and so on which are prone to create electrical interference Your Dual Link DVI Optical Transmitter Receiver This section defines the Dual Link DVI optical Transmitter Receiver o 622T Dual Link DVI Optical Transmitter see section 4 1 e 622R Dual Link DVI Optical Receiver see section 4 2 3 Your Dual Link DVI Optical Transmitter Receiver 4 1 Your 622T Dual Link DVI O
5. EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION B Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment B Use the supplied DC power supply to feed power to the machine B Please use recommended interconnection cables to connect the machine to other components 10 KRAMER SIMPLE CREATIVE TECHNOLOGY me For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution Class 1 Laser Compliance A This product complies with 21 CFR 1040 10 and EN 60825 1 CLASS 1 LASER PRODUCT 001 o2 S lt Institute of Quality amp Control NY Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000104 REV 2
6. Kramer Electronics Ltd ah KRAMER USER MANUAL Models 622T Dual Link DVI Optical Transmitter 622R Dual Link DVI Optical Receiver Contents Contents 1 Introduction 2 Getting Started 3 Overview 3 1 Power Connect Feature 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP 4 Your Dual Link DVI Optical Transmitter Receiver 4 1 Your 622T Dual Link DVI Optical Transmitter 4 2 Your 622R Dual Link DVI Optical Receiver 5 Using the Dual Link DVI Optical Transmitter Receiver 5 1 Connecting the 622T 622R 5 2 Operating the 622T 622R Dual Link DVI Optical Transmitter Receiver 5 3 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors 6 Technical Specifications Figures Figure 1 622T Dual Link DVI Optical Transmitter Figure 2 622R Dual Link DVI Optical Receiver Figure 3 622T and 622R Dual Link DVI Optical Transmitter and Receiver System Figure 4 Connecting the 622T 622R Dual Link DVI Optical Transmitter Receiver Figure 5 CAT 5 PINOUT Tables Table 1 622T Dual Link DVI Optical Transmitter Features Table 2 622R Dual Link DVI Optical Receiver Features Table 3 CAT 5 PINOUT Table 4 Technical Specifications of the 622T 622R SAAANA NSFW WWN NY CANN A omnes Introduction 1 Introduction Welcome to Kramer Electronics since 1981 a world of unique creative and affordable solutions to the infinite range of problems that confront the video audio and presentation professiona
7. also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry
8. d5 Pair 1 4and5 Pair2 3and6 Pair 2 1and2 Pair3 1and2 Pair3 3and6 Pair4 7and8 Pair 4 7 and 8 Figure 5 CAT 5 PINOUT 12 45 78 36 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 6 Technical Specifications Table 4 includes the technical specifications Table 4 Technical Specifications of the 622T 622R 622T 622R INPUTS DVI IN OUTPUTS DVI OUT BANDWIDTH 3 3Gbps POWER SOURCE 12 VDC 200mA DIMENSIONS 21 4cm x 10 35 m x 4 36cm 8 4 x 4 07 x 1 71 W D H WEIGHT 0 7 kg 1 55 Ibs approx ACCESSORIES Power supply bracket installation kit 1 DVI DVI male to male cable 1 Specifications are subject to change without notice LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHO IS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty I Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kram
9. er at one of the agents listed in the web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed 35 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removal or installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please
10. iver simultaneously However the power connect feature does let you connect just one power supply to either the transmitter or receiver In such a case use the 2 1A power supply 3 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com 1 Getting Started 2 Getting Started We recommend that you Unpack the equipment carefully and save the original box and packaging materials for possible future shipment Review the contents of this user manual Use Kramer high performance optical cables Note that the units are designed for use with MULTI MODE optical cables 3 Overview The high performance Kramer 622T and 622R have a transmission range of more than 300 ft more than 100 meters of dual link high resolution digital graphic data over fiber optic cables and EDID HDCP parameters over DDC UTP cabling In particular the 622T 622R pair Provides a dual link DVI connection supporting a resolution of up to 2560x1600 at 60Hz refresh rate Supports up to 1 65Gbps bandwidth per link and a total of 3 3Gbps for the dual link Transmits two red two green and two blue channels and one clock over the fiber optic cables with 8 simplex or 4 duplex LC fiber connectors Performs DDC HDCP interconnection over CATS with RJ 45 connectors and also provides power via the UTP cable Is strictly regulated under the Class 1 Laser Eye Safety in compliance with FDA CDRH and IEC 6
11. l on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 500 plus different models now appear in 8 Groups which are clearly defined by function Congratulations on purchasing your Kramer 622T Dual Link DVI Optical Transmitter and 622R Dual Link DVI Optical Receiver which are ideal for e Digital display systems e Flat panel displays plasma display panels and projectors in conference rooms and auditoriums e Kiosks with digital flat panel displays for information display The 622T Dual Link DVI Optical Transmitter and 622R Dual Link DVI Optical Receiver are available as two separate packages The 622T package includes the following items e 622T Dual Link DVI Optical Transmitter e Power adapter 12V DC 500mA Input and this user manual The 622R package includes the following items e 622R Dual Link DVI Optical Receiver e Power adapter 12V DC 2 1A Input and this user manual e One DVI DVI male to male cable 1 GROUP 1 Distribution Amplifiers GROUP 2 Video and Audio Switchers Matrix Switchers and Controllers GROUP 3 Video Audio VGA XGA Processors GROUP 4 Interfaces and Sync Processors GROUP 5 Twisted Pair Interfaces GROUP 6 Accessories and Rack Adapters GROUP 7 Scan Converters and Scalers and GROUP 8 Cables and Connectors 2 When setting up a transmitter receiver system you can connect the 12V power supplies to the transmitter and to the rece
12. ptical Transmitter Figure and Table 1 define the 622T Dual Link DVI Optical Transmitter POWER ig 8 acana Ea L covero l CL1 CL2 R2 G2 B2 R1 G1 B1 DDC O Dual Link DVI Optical Transmitter Figure 1 622T Dual Link DVI Optical Transmitter Table 1 622T Dual Link DVI Optical Transmitter Features Feature Function 1 CONNECTION DISPLAY LED Lights when a DVI display is connected to the 622R 2 SOURCE LED Lights when a DVI source is detected 3 POWER LED Lights when receiving power 4 CL1 CL2 Connects to the clock connectors on the 622R 5 R2 G2 6 Optic Gables B2 R1 Connect to the optic connectors on the 622R 7 G1 B1 8 DDC CAT5 Connector Connects to the DDC RJ 45 connector on the 622R 9 DVI IN Connector Connects to the DVI source 10 12V DC 12V DC connector for powering the unit 1 Using a UTP CATS cable with RJ 45 connectors at both ends the PINOUT is defined in Table 3 and Figure 5 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Your Dual Link DVI Optical Transmitter Receiver 4 2 Your 622R Dual Link DVI Optical Receiver Figure 2 and Table 2 define the 622R Dual Link DVI Optical Receiver DAQ Q srez Loin CL2 CL1 G2 R2 R1 B2 Bi G1 Dual Link DVI Optical Receiver DVI OUT Figure 2 622R Dual Link DVI Optical Receiver Table 2 622R Dual Link DVI Optical Receiver Features
13. r to the power socket of either the 622T or the 622R and connect the adapter to the mains electricity not shown 7 Turn the power on the source and the display to ON Set Top Box Source Plasma Display ZB LESS Figure 4 Connecting the 622T 622R Dual Link DVI Optical Transmitter Receiver 1 Alternatively connect the separate power supplies to the transmitter and to the receiver simultaneously Using the Dual Link DVI Optical Transmitter Receiver 5 2 Operating the 622T 622R Dual Link DVI Optical Transmitter Receiver To properly operate the 622T 622R system Make sure you have a media receiver or a graphic controller card with a DVI dual link connector on your PC MAC or SUN system display you are about to connect practice with live digital voltages Make sure that your graphic card supports the maximum resolution of the Avoid hot plugging the 622T or 622R This is not a recommended 5 3 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors Table 3 and Figure 5 define the CAT 5 PINOUT using a straight pin to pin cable with RJ 45 connectors Table 3 CAT 5 PINOUT EIA TIA 568A EIA TIA 568B PIN Wire Color PIN Wire Color 1 Green White 1 Orange White 2 Green 2 Orange 3 Orange White 3 Green White 4 Blue 4 Blue 5 Blue White 5 Blue White 6 Orange 6 Green 7 Brown White 7 Brown White 8 Brown 8 Brown S a Pair 1 4an
Download Pdf Manuals
Related Search