SUNNY BOY 8000TLUS / 9000TLUS / 10000TLUS
Contents
1. 14 Factory Defaults for non Country Dependent Parameters 14 Sunny Boy 8000 1 14 Sunny Boy COOOMU Uinta 15 Sunny Boy LOOQOTLUS ad ed he hee dite Bb 16 Country Specific Grid Settings 16 CONIC ua RES WEES 17 Technical Description SBCLUS_Par TUSO945 10 7 Table of Contents SMA America Production LLC 8 SBCLUS_Par TUSO945 10 Technical Description SMA America Production LLC Notes on this Manual 1 Notes on this Manual 1 1 Area of Validity In this document you will find the description and meaning of the operating parameters of the following SMA inverters Sunny Boy 8000TLUS SB 8000TLUS 10 Sunny Boy YOOOTLUS SB 9000TLUS 10 Sunny Boy 10000TLUS SB 100007 05 10 1 2 Target Group This manual is for qualified personnel and the operator of the Sunny Boy Activities that have to be done by qualified personnel are marked with a safety warning Qualified personnel Qualified personnel has received training and has demonstrated skills and knowledge in the construction and operation of the device Qualified personnel has received training to recognize and avoid the hazards involved Operator The operator has been adequately supervised by qualified personnel to ensure a safe use of the Sunny Boy 1 3 Additional Information You will find information on the m2. Operating Parameters SUNNY BOY 8000705 9OOOTLUS 10000705 Technical Description SBCLUS_Par TUSO94510 Version 1 0 SMA America Production LLC Copyright 2010 SMA America Production LLC All rights reserved No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photographic magnetic or otherwise without the prior written permission of SMA America Production LLC SMA America Production LLC makes no representations express or implied with respect to this documentation or any of the equipment and or software it may describe including with no limitation any implied warranties of utility merchantability or fitness for any particular purpose All such warranties are expressly disclaimed Neither SMA America Production LLC nor its distributors or dealers shall be liable for any indirect incidental or consequential damages under any circumstances The exclusion of implied warranties may not apply in all cases under some statutes and thus the above exclusion may not apply Specifications are subject to change without notice Every attempt has been made to make this document complete accurate and up to date Readers are cautioned however that SMA America Production LLC reserves the right to make changes without notice and shall not be responsible for any damages including indirect incidental or consequential damages caused
3. If you have technical problems concerning our products contact our Serviceline We need the following information in order to provide you with the necessary assistance Inverter type Inverter serial number Type and number of modules connected lnverters blink code or display Type of communication if applicable SMA America Incorporated 4031 Alvis Court Rocklin CA 95677 USA Tel 1 916 625 0870 Fax 1 916 625 0871 Service SMAAmerica com www SMA America com Technical Description SBCLUS_Par TUSO945 10 17 SMA America Production LLC 41 fa lt
4. T Start 5 5 1600 10 T Stop 5 1 3600 2 V Const Setval V 300 500 480 Vac Min Fast 0 50 50 Vac Max Fast 0 20 20 Vac Min Recnct 0 50 11 7 Vac Max Recnct 0 20 5 83 Vpv Start V 300 600 360 Technical Description SBCLUS_Par TUSO94510 15 Parameter Settings 3 1 3 Sunny Boy 10000TLUS SMA America Production LLC Name Unit Range Default CO2 Fact Ibs kWh 0 2 1 7 E_Total kWh 0 200000 0 Fon Test 1 0 0 Memory Function no function Default function param Reset Op Data Reset errors Operating Mode MPP Operation MPP Turbine V const Stop Plimit w 10100 10100 10100 w 0 10100 10100 Riso Min kOhm 400 10000 400 SMA SN Software BFR T Start 5 5 1600 10 T Stop 5 1 3600 2 V Const Setval V 300 500 480 Vac Min Fast 0 50 50 Vac Max Fast 0 20 20 Vac Min Recnct 50 11 7 Vac Max Recnct 0 20 5 83 Vpv Start V 300 600 360 3 2 Country Specific Grid Settings Name Unit Range Default Default USA UL1741 USA UL1741 2005 OFF_Grid 2005 NON IEEE1547 Fac delta Hz 0 2 3 0 69 Fac delta Hz 0 4 5 0 49 Fac MinTripTime 5 0 16 300 0 16 Vac Max 0 20 10 Vac Min 0 50 12 Vac Max Recnct 0 20 5 83 Vac Min Recnct 0 50 11 7 16 SBCLUS_Par TUSO94510 Technical Description SMA America Production LLC 4 Contact Contact
5. and you wish to match the previously acquired data Fac delta Maximum permissible frequency deviation frequency increase protection Fac delta and frequency drop protection above Fac deltat and below Fac delta the grid frequency of 60 Hz can be before the grid monitoring system disconnects the device from the grid Fac MinTripTime Utility interconnection frequency trip time Default value is optimal for installations lt 30 kW Fac Limit delta Fac Start delta For setting the frequency dependent output derating in the operating mode OFF Grid More information on this subject can be found in the Sunny Island technical description Fan Test By setting this parameter to 1 you can check the function of the fans This test turns the fans at maximum speed h_Total Total hours of operation of the inverter A change may be necessary when you exchange your Sunny Boy and want fo use the data from the old device Memory Function Default param Sets all parameters to default Reset Op Data Sets all parameters that are visible in user level to default values Reset errors Resets all permanent device disable errors 10 SBCLUS_Par TUSO94510 Technical Description SMA America Production LLC Explanation of the Operating Parameters Name Description Operating Mode Operating Modes of the Sunny Boy Sets the Sunny Boy in Maximum Power Point Tracking Mode V
6. disconnect from the grid FaultGuard Operating mode in which a distinction is made between a device disturbance and a grid voltage fault In the event of a device disturbance the fault message is sent to the remaining devices with a time lapse of 5 minutes After the 5 minutes have passed the remaining devices will disconnect from the grid as well Inthe event of a grid voltage fault all devices immediately disconnect from the grid Riso Min This parameter is used to change the threshold value for the insulation monitoring The parameter cannot be permanently saved SMA SN Serial Number of the Sunny Boy fixed Software BFR Fimware version of the operation control unit BFR fixed 12 SBCLUS_Par TUSO945 10 Technical Description SMA America Production LLC Explanation of the Operating Parameters Name Description T Start The time the inverter waits to connect to the grid after Vpv Start is exceeded This value defaults to 5 minutes after a utility fault T Stop The time that the Sunny Boy waits to disconnect from the grid when the DC voltage falls below minimum necessary V Const Setval PV Setpoint voltage for constant voltage operation These parameters only are important in case the parameter Operating Mode is set to V const Vac Min Values are used to calculate the lower limit of allowable AC voltage Default value is optimal for installations
7. lt 30 kW The default 12 results in a trip value of 88 as listed under trip limits Vac Max Values are used to calculate the upper limit of allowable AC voltage Default value is optimal for installations lt 30 kW The default 10 results in a trip value of 110 as listed under trip limits Vac Min Fast Values are used to calculate the lower limit of allowable AC voltage for fast disconnection Default value is optimal for installations lt 30 kW The default 50 results in a trip value of 50 as listed under trip limits Vac Max Fast Values are used to calculate the upper limit of allowable AC voltage for fast disconnection Default value is optimal for installations lt 30 kW The default 20 results in a trip value of 120 96 as listed under trip limits Vac Min Recnct Vac Max Recnct Values are used to calculate the lower and upper limits to reconnect to the grid after a grid failure Vpv Start Minimum DC voltage for the Sunny Boy to connect to the grid This value is above the minimum MPP voltage which is required in order to always guarantee safe connection to the grid and to minimize grid relay wear If after disconnection from the grid and in the absence of any further faults the inverter does not automatically reconnect to the grid this parameter can be decreased in small steps It should be noted that if the value is set too low this leads to an increased number of conn
8. by reliance on the material presented including but not limited to omissions typographical errors arithmetical errors or listing errors in the content material SMA America Production LLC 3801 Havana Street Denver CO 80239 U S A Technical Description SBCLUS_Par TUSO945 10 3 SMA America Production LLC IMPORTANT SAFETY INSTRUCTIONS Sunny Boy Inverter SAVE THESE INSTRUCTIONS This manual contains important instructions for Sunny Boy inverter that shall be followed during installation and maintenance of the inverter The Sunny Boy is designed and tested according to international safety requirements but as with all electrical and electronic equipment certain precautions must be observed when installing and or operating the Sunny Boy To reduce the risk of personal injury and to ensure the safe installation and operation of the Sunny Boy you must carefully read and follow all instructions cautions and warnings in this technical description Warnings A warning describes a hazard to equipment or personnel It calls attention a procedure or practice which if not correctly performed or adhered to could result in damage to or destruction of part or all of the SMA equipment and or other equipment connected to the SMA equipment or personal injury 1 DANGER DANGER indicates a hazardous situation which if not avoided will result in death serious injury WARNING WARNING indicates a hazardous situation whic
9. const Constant Voltage Mode Setpoint defined in Vconst Setval Stop Disconnection from utility no operation Plimit Upper limit of AC output power fixed Pmax Active power limitation of the inverter Technical Description SBCLUS_Par TUSO945 10 11 Explanation of the Operating Parameters SMA America Production LLC Name PowerBalMax Description Parameter for limiting the maximum output of an inverter The output limitation can be set to the maximum permissible unbalanced load that depends on the specifications of the grid operator PowerBalMax has four operating modes Off is deactivated In the event of a device disturbance grid voltage fault of an inverter only the affected inverter is disconnected from the grid remaining devices continue to operate without reducing their output PowerGuard Operating mode in which no distinction is made between a device disturbance and a grid voltage fault affected device disconnects from the grid The remaining inverters limit their output over a 10 minute average PhaseGuard Operating mode in which a distinction is made between a device disturbance and a grid voltage fault Incase of a device disturbance at the first Sunny Boy the remaining inverters will continue to operate without reducing their output Incase of a grid voltage disturbance all devices will immediately
10. ections to the grid and thus to increased wear of components Technical Description SBCLUS_Par TUSO945 10 13 Parameter Settings 3 Parameter Settings SMA America Production LLC 3 1 Factory Defaults for non Country Dependent Parameters 3 1 1 Sunny Boy 8000TLUS Name Unit Range Default CO2 Fact Ibs kWh 0 2 1 7 E_Total kWh 0 200000 0 Fan Test 1 0 0 Memory Function no function Default no function param Reset Op Data Reset errors Operating Mode MPP Operation MPP Turbine V const Stop Plimit W 8100 8100 8100 Pmax W 8100 8100 Riso Min kOhm 400 10000 400 SMA SN Software BFR T Start 5 5 1600 10 T Stop 5 1 3600 2 V Const Setval V 300 500 480 Voc Min Fost 50 50 Vac Max Fast 0 20 20 Vac Min Recnct 0 50 11 7 Vac Max Recnct 0 20 5 83 Vpv Start V 300 600 360 14 SBCLUS_Par TUSO94510 Technical Description SMA America Production LLC 3 1 2 Sunny Boy 9YOOOTLUS Parameter Settings Name Unit Range Default CO2 Fact lbs kWh 0 2 1 7 E_Total kWh 200000 0 Fan Test 1 0 0 Memory Function no function Default function param Reset Op Data Reset errors Operating Mode MPP Operation MPP Turbine V const Stop Plimit w 9100 9100 9100 Pmox w 0 9100 9100 Riso Min kOhm 400 10000 400 SMA SN Software BFR
11. h if not avoided could result in death or serious injury CAUTION CAUTION indicates a hazardous situation which if not avoided could result in minor or moderate injury NOTICE NOTICE indicates a situation that can result in property damage if not avoided 4 SBCLUS_Par TUSO945 10 Technical Description SMA America Production LLC Other Symbols In addition to the safety and hazard symbols described on the previous pages the following symbol is also used in this technical description Informotion J This symbol accompanies notes that call attention to supplementary information that you should know and use to ensure optimal operation of the system Markings on this Product The following symbols are used as markings on this product with the following meanings Warning regarding dangerous voltage The product works with high voltages All work on the product may only be done as described in its documentation Beware of hot surface The product can become hot during operation Avoid coming into contact with the product during operation Observe the operating instructions Read product s documentation before working on it Follow all safety precautions and instructions as described in the documentation 111741 is the standard applied by Underwriters Laboratories to the Sunny Boy to certify US that it meets requirements of the NEC and IEEE 929 2000 IEEE 929 2000
12. ounting installation commissioning and maintenance of the inverter as well as device specific technical data in the installation guide of the respective inverter You will find information on the operation of the inverter in the user manual for the Sunny Boy Technical Description SBCLUS_Par TUSO945 10 9 Explanation of the Operating Parameters SMA America Production LLC 2 Explanation of the Operating Parameters The various operating parameters control the functionality of the Sunny Boy They can only be viewed and changed via a communication device or communication software grayed out parameters Some parameters can only be viewed an installer The so called installer password is required for this Only the installer can change parameters e Youcan see the default settings of the inverter in the specifications on the type plate I Name Description CO2 Fact The Sunny Boy evaluates the yield and indicates the approximate CO2 emission avoided by your Sunny Boy The amount of CO2 avoided is computed according to the kWh produced E otal multiplied by the factor defined in the parameter CO2 Default Used for adjusting the parameters country specific settings Note After changing one of the parameteres marked with the parameter Default changes to adjusted automatically E_Total Total energy yield of the inverter Changing the value can be necessary when a Sunny Boy is exchanged
13. provides recommendations regarding the proper equipment and functionality necessary to ensure compatible operation when power generation is connected to the utility grid AC current ZZZ DC current Transformerless Earth Ground 11741 is the standard applied by Underwriters Laboratories to the Sunny Boy to certify cus that it meets the requirements of the NEC and IEEE 929 2000 IEEE 929 2000 provides recommendations regarding the proper equipment and functionality necessary to ensure compatible operation when power generation is connected to the utility grid Technical Description SBCLUS_Par TUS094510 5 SMA America Production LLC General Warnings General Warnings The Sunny Boy contains no user serviceable parts except for the fans on the bottom of the enclosure and the filters behind the fans as well as the handle covers on the sides of the unit For all repair and maintenance always return the unit to an authorized SMA Service Center 6 SBCLUS_Par TUSO94510 Technical Description SMA America Production LLC Table of Contents Table of Contents 1 1 1 1 2 1 3 2 3 3 1 3 1 1 3 1 2 3 1 3 3 2 Notes on this 9 Areg of Validify2 Sh ceeds aa ante See 9 Target Group 9 Additional Information 9 Explanation of the Operating Parameters 10 Parameter Setfings
Download Pdf Manuals
Related Search