Hoover Domestic Appliance User Manual
Contents
1. If the mains cord on this appliance is damaged it must be replaced by a special cord which is ONLY obtainable from the GIAS spares service It must be installed by a competent person Call GIAS 01204 556111 40004968 qxd 23 05 2007 13 40 Page 8 Connecting to the cold water supply Only one hose is required to install this machine to a cold This Appliance water supply Cold fill is an energy efficient system Only the water required must be to wash the laundry is heated There is no loss of heat in the pipeline from the hot water tank or the boiler connected to a pice tke If your previous machine installation was hot and cold fill COLD WATER ensure that the hot tap is firmly closed to prevent leakage This machine has an inlet hose with a 19mm 3 4 threaded supply only F ferrule fitted to the end to attach between the threaded connector on the appliance and the water supply Only use the new hose supplied to connect the machine and ensure that the sealing washers are in place inside the hose connectors Do not re use old hoses which are attached to existing installations Do not over tighten the connections Hand tight is sufficient Do not trap or kink the hose 1 Connect the elbow end of the hose provided to the threaded inlet on the back of the machine Grey pipe to the white threaded inlet on the machine 2 Hand tighten the connector 3 Connect the straight ends of the pipes t2. The Control Panel Digital Display Stain Sensitive Delay Blaster Care Start O 2 O DOO Temperature HNL 71463D OFF Made in UK Rapid 29 Cotton P Coloureds LE Synthetics Delicate SPIN SPEED SELECTOR OPTIONS BUTTONS The programme selector must be return to the OFF position to reset the controls between each wash cycle To start another wash cycle the programme selector must be returned to OFF once again before the next programme can be selected and started 16 TEMPERATURE START SELECTOR PROGRAMME SELECTOR PAUSE Turning the machine On Turn the machine ON by selecting a programme using the programme selector This status will be indicated by the END indicator light flashing this light will continue to flash until the machine has started or the machine is returned to the OFF position Start Pause START After selecting the programme and the required options press the Start Pause button once to start the wash cycle The END light will stop flashing and START light will illuminate and there will be a short time delay to the start of the programme while the machine sets the wash parameters for the selected programme and options The door locked indicator light A will also illuminate a few seconds after pressing the Start Pause button PAUSE The programme may be paused at any time during the wash cycle by holding do
3. 2 Lay the machine on its back and remove the base and the two polystyrene spacers on each side of the machine We recommend that a second person assist in the lifting and manoeuvring of the machine Dispose of the packaging safely Make sure it is out of the reach of children it is a potential source of danger 3 Return the machine to the upright position remove the remainder of the packaging and the central screw in the transit bar 40004968 qxd 23 05 2007 13 38 Page 5 4 Remove the four retaining screws in the transit bar and pull out the transit bracket We recommend you keep the transit bracket and screws to protect the machine for future transit The manufacturers will not be responsible for any damage to the machine caused by not following the instructions relating to releasing the transit protection The user is responsible for all installation costs 5 Take the base panel provided and fit the two self adhesive strips by removing the backing paper on one side and locating the strips on each side of the base panel 6 Tilt the machine forward and locate the base panel under the front of the machine Remove the remaining backing paper from the self adhesive strips and offer up the base panel to the bottom of the cabinet 40004968 qxd 23 05 2007 13 39 Page 6 r the base of the machine Bring the machine back to the A 7 Take the two plastic fixing clips and fix the base panel to S upright posi
4. The degree of soiling It is possible to reduce the amount of detergent used depending on the degree of soiling Use less detergent for less soiled items Amount of laundry It is possible to reduce the amount of detergent when washing only a small amount of laundry For smaller loads use less detergent The dosages shown on the packaging of detergents for washing delicates often already refer to a reduced wash size Always follow the dosage instructions on the detergent packaging 14 p 40004968 qxd 23 05 2007 13 40 Page 15 T Dispensing instructions The detergent drawer is split into 3 compartments the lefthand compartment labelled II is for detergent utilised during the main wash the centre compartment labelled 3 is for special additives such as fabric softeners fragrances starch brighteners etc the righthand compartment labelled I is for detergent utilised during Prewash Dispensing in the drum Liquid detergents and some tablets are dispensed via the machine drum using the recommended dispensing device which is placed upright on top of the washload towards the back of the drum Some tablets are designed to be placed in the dispenser drawer check the detergent pack for details Do not put any items into the drawer other than detergents that are designed to be dispensed from the drawer as they may cause blockage or damage 15 40004968 qxd 23 05 2007 13 40 Page 16 o
5. selected after cancelling the previous programme When the programme has finished Wait approximately two minutes for the door lock to be released When the door locked indicator light goes out it will then be safe to open the door Switch off the machine by turning the programme selector to the OFF position so that it will be ready the next time you use the machine this action resets the memory in the machine Open the door Remove the laundry Disconnect the plug from the mains power supply and turn off the water supply whenever you finish using it 40004968 qxd 23 05 2007 13 40 Page 25 an Cleaning and Routine Maintenance The washing machine needs very little maintenance but regular attention to a few small details will ensure the continued performance of your washing machine Do not use abrasive cleaners scouring pads solvent based cleaners or polishes wiping the outside of the machine with a damp cloth will suffice Cleaning the soap dispenser 1 Clean the compartments occasionally to remove detergents and additives 2 Todo this you just need to pull the drawer out firmly from the machine but without forcing it 3 Clean the compartments and the syphon cover under warm running water 4 Clean the outlet of the soap dispenser to remove any residue of soap powder 5 Replace the drawer Cleaning the door glass Regularly clean the door glass with a damp cloth A build up of soiling and residues from
6. the water may result in water leaking from the door Do not use abrasive cleaners as they can scratch the surface 25 40004968 qxd 23 05 2007 13 40 Page 26 an Cleaning the filter The washing machine is fitted with a special filter to prevent items such as coins buttons etc blocking the discharge hose These may be retrieved by 1 Removing the kickplate by gently pulling it from the bottom in an outwards and upwards direction 2 Use the kickplate to collect the water still in the filter 3 Use a screwdriver to loosen the screw holding the filter turn the filter anticlockwise until it stops remove it and clean it After cleaning it reassemble following the above instructions in reverse order Replace the kickplate We recommend that the filter be cleaned frequently at least once a month Maintenance wash Using small quantities of detergent and low temperature wash programmes can cause the gradual build up of grease dirt and scale Over time these deposits can damage your laundry and your machine They can also cause your machine to smell We recommend that you carry out a maintenance wash a couple of times per year to keep your machine and pipe work clean and free of these deposits Simply run the Cottons 90 C programme without a load and with the normal quantity of detergent This wash will take approximately 2 hours to complete 26 40004968 qxd 23 05 2007 13 40 Page 27 ae Troubleshoot
7. until the required spin speed is indicated To select a full spin cycle please turn the dial to the required spin programme Press the Fast Iron button to continue with the programme The machine will then pump out the water and the programme will conclude with a short spin Finally the programme carries out a brief tumbling action to loosen the items in the load Press the Fast Iron button and the machine will pump out the water and complete the cycle with a short spin cycle Press the Fast Iron button and the machine will pump out the water to complete the cycle The load will not be spun and will therefore be very wet It is not possible to select a spin speed higher than that suitable for the programme selected This feature is designed to avoid damaging the fabrics It is possible to modify the spin speed at any time without stopping or pausing the machine 19 40004968 qxd 23 05 2007 13 40 Page 20 r Automatic Features Automatic Variable Capacity Half Load The washing machine is fitted with a self adjusting water level system This system enables the machine to use the optimum amount of water needed to wash and rinse the laundry in relation to the particular load This results in a reduction of the water and electricity used without in any way compromising the washing and rinsing performance The amount of water and electricity used will always be appropriate for the clothes load The washing machine automaticall
8. 3 rinses one for fabric conditioner and no final spin Wool This is a programme dedicated to washing fabrics labelled with the woolmark symbol The cycle consists of alternate periods of activity and pauses Washing and rinsing are carried out using a high water level to provide the best results The programme has a maximum temperature of 40 C and concludes with 3 rinses one for fabric conditioner and a short spin at 800rpm Sports This washing machine has a unique Sportswear programme It is specially designed to wash mixed sportswear fabrics that cannot be washed on hotter programmes and is designed to remove the soiling and staining created by participation in sports activities This programme starts with a cold prewash that breaks down and loosens any excess dirt and then washes at a cool 30 C rinses twice one is for fabric conditioner and spins at 800rpm for the best care of your heavily soiled delicate garments Detergent for the prewash part of the programme should be added to compartment I and detergent for the mainwash should be added to compartment II Follow the instructions given in The Dispenser section Rapid 29 The 29 minute rapid programme allows a complete washing cycle to be completed in under half an hour with a maximum load of 2kg and a temperature of 40 C The programme is particularly suited to lightly soiled cottons and mixed fabrics When selecting the Rapid 29 programme we recommend you use o
9. 40004968 qxd 23 05 2007 13 38 Page 1 o Instruction Book NeXrRA Delay Temperature Sef Temperat iron pee Res a T C90 60 40 30 tain Fast Start laser are Pause HNL 714630 Mode in UK Pe Cotton P 40004968 qxd 23 05 2007 13 38 Page 2 Contents Q0 Introduction 0 a 3 Delivery information 000000 cece eee 3 Do s and Don ts 0 0 cc ccc eee eens 3 Unpacking the Product 4 Installation 00 0006 ccc 7 Choose a location 0 00 cee ee 7 Electricity supply 0 0 000 eee ees 7 Water supply 0 00 eee eee 7 Connecting to the cold water supply 224 8 Connection of the machine to the drain 9 Moving the machine into position 10 Adjusting the feet 0 000 eee 10 Testing the installation 11 Washing advice 0 000005 12 Loading your washing machine 000 05 12 Sorting the laundry 0000 0c eee eee 13 The Dispenser 6000 c cece eee 14 Detergent dosage 0000 e eee eee 14 Dispensing instructions 000 eee eee 15 The Control Panel 0 00005 16 Wash Options 000 000s 18 Automatic Features 0 00000 ee 20 Programme Selector 20 Programme Guide 4 22 A Typical Wa
10. R TEMPERATURE INDICATOR Information on the status of the wash programme is constantly provided by the display Wash Temperature When a programme is selected the relevant indicator will light up to show the maximum possible wash temperature Selecting a lower temperature using the Temperature button will be indicated on the display Example Coloureds programme will default to 60 C With this control the temperature can be reduced to 40 C to give a non fast coloureds wash Note The temperature must be adjusted before selecting the Wash Time Door Locked Indicator Once the Start Pause button has been pressed the light flashes and then remains on until the end of the wash cycle 2 minutes after the end of the wash the light goes off to show that the door can be opened 17 p 40004968 qxd 23 05 2007 13 40 Page 18 c Spin Speed When a programme is selected the maximum spin speed allowed for that programme appears on the display Pressing the Spin Speed button will reduce the speed by 100 rpm each time the button is pressed The minimum speed is 400 rpm or continuing to press the button will eliminate the final spin completely Delay Start This indicator flashes when the delay start has been set Wash Cycle Time When a programme is selected the display automatically shows the wash cycle time which can vary depending on the options selected Once the programme has started you will be kept informed constantly of th
11. anual 3 Unclip the drain hose from the rear panel of the machine and lower the hose into a bowl on the floor When the bowl is full raise the end of the drain pipe to a height higher than the top of the appliance to stop the flow of water Empty and replace the bowl and continue draining the machine until empty 4 Once the machine is fully drained of water clip the hose to the rear of the machine Press the door button and remove the load The door can be opened approximately 2 minutes after the power failure Do not force open the door 30 40004968 qxd 23 05 2007 13 40 Page 31 ae Customer Service For a period of one year from the date of purchase the appliance is covered by a guarantee which allows you to call Hoover Service free of charge except for the price of the call Phone GIAS on 08705 400 600 Remember to send off the guarantee certificate for validation within 10 days of the date of purchase You should retain the receipt issued by the retailer when you purchased the machine to show to the call out engineer should you need to consult one If your washing machine shows signs of a defect or is not working properly before you contact GIAS Service we recommend you carry out the checks detailed within the Troubleshooting section If the problem with the machine persists after completing all the recommended checks please dial the GIAS Service number You will be connected directly to GIAS It i
12. e time remaining to the end of the wash Programme Start light This indicator will light up when the Start button has been pressed Wash Time When the programme is selected the relevant indicator will light up to show the minimum possible wash time Selecting the Wash Time using the button will cause the corresponding indicator to light up Note the wash time can vary automatically depending on the temperature selected Wash Options The following options should be selected BEFORE pressing the Start Pause button The light on each option button will come on if that option has been selected Stain Blaster By pressing this button which can only be activated in the Cotton cycles the sensors in the new Sensor System come into operation They affect both the selected temperature keeping it at a constant level throughout the wash cycle and the mechanical function of the drum The drum is made to turn at two different speeds at crucial moments When the detergent enters the garments the drum rotates in such a way that the detergent is distributed in a uniform manner However during the wash and rinse procedures the speed increases in order to maximise the cleaning action Thanks to this special system the efficiency of the wash procedure is improved WITHOUT ANY INCREASE IN THE LENGTH OF THE PROGRAM Sensitive Care By pressing this button you can activate a special new wash cycle in the Colourfast and Synthetics programmes than
13. electricity supply 3 Select the Spin programme and then press the Start Pause button to start the machine Allow the programme to continue for one minute and then cancel the programme by returning the selector to the OFF position This will remove any water remaining in the machine from factory testing 4 To check for cold water filling to the machine Select the Rinse programme and press the Start Pause button to start the machine Allow the tumble action to continue until the water has pumped out Check that the drain outlet is not leaking or overflowing 5 Switch off the machine at the end of the cycle by turning the programme knob to the OFF position 6 Select the Spin programme and press the Start Pause button to start the machine If the machine takes longer than one minute to empty check the drain hose for kinks Installation testing is now complete Now you have successfully installed the machine we advise that you run the machine to ensure the drum is thoroughly clean after testing and storage Select Colourfast 60 C programme and run the machine for a complete cycle using only wash detergent and water This programme will take approximately 2 hours to complete 11 40004968 qxd 23 05 2007 13 40 Page 12 Washing advice 12 The following tips are designed to assist in getting the best results from your machine whilst using it in the most environmentally friendly and economical way It is als
14. ets of clothing that can rattle in the drum and cause damage Is the load unbalanced Stop the programme re distribute the load and restart The programme takes a long time Some programmes do take a long time over 2 hours Low water pressure can increase the length of the programme The door will not open Has the programme finished Is the END light illuminated If not the programme is not complete Has the door locked light gone out If not wait a further couple of minutes and the light will go out and you will be able to open the door 40004968 qxd 23 05 2007 13 40 Page 29 an Has the programme finished but the door remains locked The display reads Error 2 Turn the machine to OFF to reset the machine and this will allow the door to open If water remains in the drum refer to Water does not drain away above Problem with the dispenser Not all the detergent has been flushed away 1 Check the water supply tap is fully turned on 2 Check the inlet hose is not kinked The dispenser drawer will not close properly 1 Check the drawer is aligned properly 2 Check the drawer is not clogged with detergent see Cleaning and routine maintenance Steam is coming from the dispenser The machine is designed to vent through the drawer this is nothing to worry about Remember you may be charged for the service call if incorrect installation or misuse causes a problem with your machine If the f
15. f this manual entitled The Dispenser We recommend you use only 20 of the quantity used for the main wash programme Drain Rinse Spin Synthetics Washing and rinsing performance is optimised through drum rotation speeds and water levels for synthetics and mixed fabrics The programme will default to 60 C The delicate spin action minimises creasing The final spin speed for the synthetics programme is 800rpm 20 p 40004968 qxd 23 05 2007 13 40 Page 21 r Delicates This is a new concept in washing with a cycle that consists of alternate periods of activity and pauses particularly suitable for washing very delicate fabrics Washing and rinsing are carried out using a high water level to provide the best results Rinse This programme carries out three rinses with an intermediate spin which can be reduced or excluded by using the Spin Speed option It can be used for rinsing any type of fabric e g use after hand washing Spin The Spin programme completes the spin at the maximum spin speed this can be reduced by using the Spin Speed option button Drain This programme drains out the water Silk This washing machine also has a gentle Silk and Hand Wash programme This programme allows a complete washing cycle for garments specified as Hand Wash only and laundry items made from silk or specified Wash as silk on the fabric label The programme has a maximum temperature of 30 C and concludes with
16. ing What might be the cause of Defects you can remedy yourself Before calling GIAS Service for technical advice please run through the following checklist A charge will be made if the machine is found to be working or has been installed incorrectly or used incorrectly If the problem persists after completing the recommended checks please call GIAS Service tel 08705 400 600 they may be able to assist you over the telephone The machine will not start Close the door Check that there is power to the machine Select a programme and press Start Pause Check if the door locked light is illuminated If it is not check the following 1 Is the machine connected to the electrical supply 2 Is the electrical supply OK check another socket 3 Has the fuse on the machine blown If so replace it Ifthe door locked light is illuminated and the machine does not start this means that the machine cannot fill with water check the following 1 Check the programme dial is correctly aligned with the programme 2 Is the water supply to the machine switched on 3 Are the pipes kinked or restricted in any way Water does not drain away error 3 will be displayed Ensure that there is not a blockage in the drain hose or the hose is not kinked Is the drain hose installed correctly If connected to the sink waste make sure you have cut the membrane or removed the bung from the under sink drainage unit Chec
17. k for foreign bodies in the filter If present clean the filter If you have found any of the above problems correct them and run the machine through a spin cycle to drain the water 27 40004968 qxd 23 05 2007 28 13 40 Page 28 Water on the floor around the washing machine Is the fill hose tightened If so replace the rubber washers and re tighten Is the standpipe or the household drain blocked If so clear the blockage yourself or call a plumber Is there clothing or dirt between the door gasket and the door glass Ensure that the door glass and gasket are kept clean and free of laundry when loading the machine The machine does not spin Water has not drained from the machine Check the points highlighted above Have you selected an option that changes the spin profile change of spin speed on the selector Check the feature in the description of the controls Is the load unbalanced To reduce noise and vibration and improve the machine s reliability and life the machine is fitted with an electronic sensor that detects if the load is unbalanced To improve the spin performance the load can be re distributed by hand at the end of the cycle and then re spun The machine is noisy or vibrates a lot during the cycle Has the transit system been fully removed Check that the bracket and the polystyrene packing have been taken off the machine Are there any loose items in the pock
18. ks to the new Sensor System This option treats with care the fibres of garments and the delicate skin of those who wear them The load is washed in a much larger quantity of water and this together with the new combined action of the drum rotation cycles where water is filled and emptied will give you garments which have been cleaned and rinsed to perfection The amount of water in the wash is increased so that the detergent dissolves perfectly ensuring an efficient cleaning action The amount of water is also increased during the rinse procedure so as to remove all traces of detergent from the fibres This function has been specifically designed for people with delicate and sensitive skin for whom even a very small amount of detergent can cause irritation or allergy 18 p 40004968 qxd 23 05 2007 13 40 Page 19 o You are advised to also use this function for children s clothing and for delicate fabrics in general or when washing garments made of towelling where the fibres tend to absorb a greater quantity of detergent To ensure the best performance for your wash this function is always activated on the Delicates and Woollens programmes Delay Start This option is available to delay the start of the wash cycle by up to 9 hours The selection of the time is completed by pressing the Delay Start button the countdown display will indicate the time selected When the correct delay is selected press the Start Pau
19. ne free of combustible materials such as lint paper rags chemicals etc Electricity supply Washing machines are supplied to operate at a voltage of 240V 50 Hz single phase Check that the supply circuit is rated to at least 13A The plug is already equipped with a 13A fuse which is BS 1362 ASTA approved Any replacement must be the same rating and specification If the fuse cover is lost do not use the plug until it is replaced Electricity can be extremely dangerous This washing machine must be earthed The socket outlet and the plug on the appliance must be of the same type Do not use multiple adapters and or extension leads The wires in the mains lead are coloured in accordance with the following codes Blue NEUTRAL Brown LIVE Green and Yellow EARTH CE Appliance complies with European Directive 89 336 EEC 73 23 EEC and subsequent amendments Water supply The cold water pressure should be between 0 5 and 8 bar 0 05 0 8 Mpa Do not connect the machine to a single outlet instantaneous water heater The water supply tap should be accessible when the machine is installed Before connecting the fill hose check that the water is running from the water supply tap to be used p Do not plug the machine in and switch it on at the mains until the installation is completed You may be charged for a service call if a problem with your machine is caused by incorrect installation
20. nly 20 of the quantities shown on the detergent pack 21 40004968 qxd 23 05 2007 13 40 Page 22 Programme Guide Maximum Maximum Programme Fabric Type Load Water Size kg Temp C Cotton P Cottons and linen Coloureds Cottons colourfast mixed fabrics Mixed fabrics and synthetics Delicate fabrics Silks and Hand Wash only garments Machine washable wool Mixed fabrics Lightly soiled cottons and mixed fabrics gj gi Synthetics Be E Delicate El E gi n n n me g E zy ro 0 x D 2 P o 5 D a el Energy label data based on Colourfast programme tested in accordance with CENELEC EN60456 22 40004968 qxd 23 05 2007 13 40 Page 23 T A Typical Wash This section summarises the main points when completing a wash cycle For detailed explanations of features options and details of the machine refer to the relevant section in the instruction manual Preparing the laundry Select and sort the laundry according to the wash care labels found on each garment Always check the care labels Loading the laundry Open the door Put the laundry in the washing machine Close the door by pushing it until it clicks ensuring that no items of laundry are obstructing the lock or door seal Putting detergent in machine Open the drawer choose the detergent and put in the recommended amount Do not exceed the dosage stated below Maximum s Compartment quantity of a owder li
21. o important to understand the items to avoid in your laundry to ensure the continued safe and reliable operation of your machine Loading your washing machine To make further reductions of energy water and detergent consumption we recommend that you put a full load into your machine Energy savings of up to 50 can be achieved by washing one full load compared to two half loads Do not overload the machine as this will reduce the quality of the wash and may cause damage to the machine and your laundry When is prewashing really needed Only with particularly dirty loads Energy savings of 5 to 15 are made by not selecting the prewash option for less dirty laundry Pre treat awkward stains with a washable stain remover Which wash temperature should you choose Using stain removers before machine washing reduces the need to wash at temperatures over 60 C Using a 40 C wash temperature can make energy savings of up to 50 Heavily soiled laundry To ensure the best performance when washing a particularly dirty load we recommend that you reduce the amount of items to be put into the machine Allowing more space in the drum the items can circulate more freely and will wash better 40004968 qxd 23 05 2007 13 40 Page 13 T Sorting the laundry Items to avoid We recommend that you do not wash underwired bras in the i machine Should the wires become detached they could cause Do not use the machine damage to your clothe
22. o the water supply ensure that there are no kinks 4 Turn on the water supply and check for leaks If there is a leak turn off the water supply disconnect the hose and check the sealing washers are in place Refit the hose and turn on the water supply 40004968 qxd 23 05 2007 13 40 Page 9 an Connection of the machine to the drain This machine must be connected in accordance with the water supply regulations Water byelaws prohibit connection to a surface water drain Decide which plumbing option suits you best then follow the instructions below All machines are tested with water prior to leaving the factory so a small amount of water may remain in the drum and drain hose Flooding could occur if any part of the installation is not completed correctly Option 1 Waste pipe connection waste trap Fit the hooked end support to the outlet pipe Position at least 800mm off the floor After removing the blanking plug or cutting the membrane from the waste system securely fix the outlet pipe to the drainage system using a hose clip Secure the hooked end support up to at least 800mm to avoid water being drawn back into the machine T z hooked end support sink Pe flexible F discharge hose TERS H es ooo 4 hose clip f 800 mm trap with hose adaptor Option 2 Into a standpipe Ens
23. oduct in peak condition you may wish to take out a Hoovercare policy which for an annual payment provides a comprehensive maintenance and repair scheme For more information please call 08705 400 600 The Hoovercare scheme is not available in Eire The manufacturer declines all responsibility in the event of any printing mistakes in this booklet The manufacturer also reserves the right to make appropriate modifications to its products without changing the essential characteristics 40004968
24. ollowing error codes are displayed switch OFF the machine and contact GIAS Service 0 1 4 5 7 8 and 9 Note The use of environmentally friendly phosphate free detergents check detergent information on pack can have the following effects Waste water from rinsing may be cloudier because of the presence of a white powder zeolites held in suspension without the rinse performance being adversely affected Presence of white powder on laundry after washing which is not absorbed by the fabric and does not alter the colour of the fabric The presence of foam in the final rinsing water is not necessarily an indication of poor rinsing Carrying out more rinse cycles does not serve any purpose in such cases 29 40004968 qxd 23 05 2007 13 40 Page 30 an Power Failure If there is a power failure the wash cycle will be interrupted and the wash programme and functions will be suspended When the power is restored the wash programme and functions will re start from the same point and complete the programme During a power failure the water can be drained and the load can be removed from the machine as follows 1 Switch off the machine both via the programme knob and the mains power supply Remove the plug from the mains power supply socket 2 Carefully move the machine so the rear of the machine is accessible Please follow the safety precautions which we recommend under the Safety Notes section of this m
25. quid a _ gt i ie Prewash option 100ml MAX Main Wash 200ml all programmes Fabric Conditioner 200ml Close the drawer again Liquid detergents and some concentrated powders and tablets that are to be placed directly into the drum should be placed in the recommended dispensing device 23 40004968 qxd 23 05 2007 13 40 Rapid 29 Page 24 Cotton P Coloureds Ce Synthetics Delicate 24 Selecting the wash programme Refer to the Programme Guide or the programme descriptions on the front of the machine to select the most suitable programme The programme is selected by turning the programme selector and aligning the programme name with the indicator Check that the END indicator is flashing if not check that the door is properly closed Check that the tap is turned on and that the discharge hose is positioned correctly Select the required wash options Starting the wash cycle Press the Start Pause button The door locked indicator and the START light illuminate and then after a few seconds the programme will begin Do not try to open the door when the door locked indicator is on Do not open the dispenser drawer during the wash programme If you wish to pause the programme press the Start Pause button after two minutes you will be able to open the door To cancel the programme the programme selector should be turned to the OFF position A new programme can be
26. s and the machine If the washcare label to wash items that do states that the bra is machine washable then we advise placing not have a wash label it in a wash bag Recommendations Always follow the wash care labelling on the garments Fasten zips tie strings and close press studs to prevent tangling Ensure that pockets are emptied of loose change and other small items Do not wash items previously treated with solvents Check that there are no metal objects in the laundry as these may damage the laundry and the machine Place small items in a wash bag 13 40004968 qxd 23 05 2007 13 40 Page 14 T The Dispenser COMPARTMENT 88 COMPARTMENT I Fabric Conditioner Prewash detergent Maximum dosage 200ml Maximum dosage 100ml of powder COMPARTMENT Il Mainwash detergent Maximum dosage m 200ml of powder Detergent dosage Only use detergents which are suitable for use in a washing DO NOT exceed machine You will obtain the best results from your wash with the maximum the minimum use of chemical products and the best care for your laundry if you take into consideration the degree of soiling as well as the type of detergent to choose detergent dosage The amount of detergent to use depends on Water hardness Depending on the hardness of the water and the type of detergent used it is possible to reduce the amount of detergent The softer the water supply the less detergent is required
27. s important you tell the GIAS advisor your product s model number and serial number which you will find on the rating label 16 characters beginning with the number 3 found on the front of the washing machine door area By doing this your enquiry will be responded to more efficiently 31 40004968 qxd 23 05 2007 13 40 Page 32 ae Your Guarantee Hoover guarantees all parts of this product for 5 years from the date of purchase During that time Hoover will replace or repair all defective parts free of charge except for parts subject to fair wear and tear such as belts The call out fee and labour costs are chargeable after the first 12 months To qualify for benefits under the guarantee you must be able to provide proof of date of purchase and the appliance must have been installed and used in accordance with the instructions described in this manual Consequential losses and accidental damage to the machine is not covered by the guarantee Hoover cannot be responsible for the results of using this machine for any purposes other than those described in this manual This guarantee does not effect your statutory or common law rights For service and repairs please call our national number GIAS Service Tel 08705 400 600 Support Service Eire 018301 666 Always use genuine Hoover spares available direct from GIAS Service Hoover Spares Service Tel 01204 556111 Hoovercare To maintain your Hoover pr
28. se button to start the cycle Temperature The Temperature button allows the reduction in the wash temperature in each programme Each time the button is pressed the temperature decreases until a minimum of 15 C cold wash kK Note The temperature must be adjusted before selecting Wash Time Fast Iron This option is only available on the Synthetics Acrylics Woolmark and Silk programmes Fast Iron function Action required to complete the cycle Synthetics The programme is completed by a short spin of very low speed Acrylics The machine stops in the final rinse stage and the option indicators blink The load is held in the water in the drum thus reducing creasing and enabling easier ironing Woolmark The machine stops in the final rinse stage and the option indicators blink The load is held in the water in the drum thus reducing creasing and enabling easier ironing Silk The machine stops in the final rinse stage and the option indicators blink The load is held in the water in the drum thus reducing creasing and enabling easier ironing Spin Speed The spin cycle is very important to remove as much water as possible from the laundry without damaging the fabrics You can adjust the spin speed of the machine to suit your needs By pressing the Spin Speed button it is possible to reduce the maximum spin speed and if you wish the spin cycle can be cancelled To re activate the spin cycle it is enough to press the button
29. sh 000 000000 23 Selecting the wash programme 000 0000 0 24 Starting the wash cycle 000 cece eee ee 24 Cleaning and Routine Maintenance 25 Troubleshooting 000000 05 27 Power Failure se 2s s 2s044 o09 nee ate ee meee seed aes 30 Customer Service 006 c cee 31 Your Guarantee 600 c cece 32 HOOVErCare sec ek eee Ee ha ee ee WE ee E 32 40004968 qxd 23 05 2007 13 38 Page 3 o Introduction Please read and follow these instructions carefully and operate the machine accordingly This booklet provides important guidelines for safe use installation maintenance and some useful advice for best results when using your machine Keep all documentation in a safe place for future reference or for any future owners Delivery information Please check that the following items are delivered with the appliance Instruction manual Guarantee card Blanking plug Inlet hose amp bracket Base panel amp x2 push clips Energy Label I Do s All packaging materials used are environmentally friendly and recyclable Please help dispose of the packaging via environmentally friendly means Your local council will be able to give you details of current means of disposal To ensure safety when disposing of an old washing machine disconnect the mains plug from the socket cut the mains power cable and destroy this together wi
30. th the plug To prevent children shutting themselves in the machine break the door hinges or the door lock This machine is solely for domestic use i e to wash rinse and spin dry household textiles and garments f Don ts Do not touch the appliance when hands or feet are damp or wet Do not lean on the door when loading the machine or use the door to lift or move the machine Do not use adapters multiple connectors and or extensions Do not allow children to play with the machine or its controls Do not try to open the door when water is visible in the drum or the door locked indicator is ON p Check that no damage has occurred to the machine during transit If it has call for service by GIAS Call 08705 400 600 PLEASE NOTE This machine only requires a cold water supply If the appliance is not running properly or breaks down switch it off disconnect the plug from the socket turn off the water supply and do not tamper with the appliance Consult GIAS Service for possible repair Call 08705 400 600 Failure to comply with the above can compromise the safety of the appliance You may be charged for a service call if a problem with your machine is caused by misuse 40004968 qxd 23 05 2007 13 38 Page 4 ae Unpacking the product Remove the machine from its packaging close to the final location of the machine 1 Cut carefully around the base of the packaging
31. tion 8 Cover the central hole in the rear of the machine with the cap enclosed in the instruction bag European directive 2002 96 EC This appliance is marked according to the European directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol on the product indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 40004968 qxd 23 05 2007 13 39 Page 7 o Installation Choose a location After the machine has been installed ensure that the mains plug and water supply valves are easily accessible Make sure there is enough space for the machine Select a space at least 600mm wide and 850mm high Also leave enough space to open the door fully so you can load and unload it easily Keep the area underneath and around the machi
32. ure that the standpipe is not located near an electrical socket Fit the hooked end support to the outlet pipe Install the hose into the standpipe ensuring that the pipe is at least 500mm from the floor Insert the outlet pipe approximately 100mm into the standpipe hi 100 rhm a Il J 500 mm min A M Cg P ae Of 5 40004968 qxd 23 05 2007 13 40 Page 10 10 Do not drag or lift the machine by its door o Moving the machine into position Your machine is heavy so care must be taken when moving it We recommend that two people move the machine to avoid strain and possible injury Take care not to damage flooring when moving the machine When moving the machine to its final position take care not to kink or damage the hose at the back of the machine Adjusting the feet Once the machine is in place the feet should be adjusted to ensure that the machine is level If the machine is not level it may become noisy or move Adjust the feet on the front corners of the machine until the machine is firm and level When the machine is firm and level tighten the locking nuts on the two feet 40004968 qxd 23 05 2007 13 40 Page 11 ae Testing the installation Refer to Selecting the wash programme for details of how to select programmes 1 Turn on the water supply and check for leaks from the fill hose 2 Switch on the
33. wn the Start Pause button for about two seconds The door locked indicator light will remain illuminated for approximately 2 minutes The door can be p 40004968 qxd 23 05 2007 13 40 Page 17 r opened when this indicator goes out To restart the programme press the Start Pause button once again Cancelling and changing the programme To cancel the programme the programme selector should be rotated to the OFF position Select a new programme and start as detailed above Door Locked indicator The door locked indicator light is illuminated when the door is fully closed and the machine is ON When Start Pause is pressed on the machine with the door closed the indicator will flash momentarily and then illuminate If the door is not closed the indicator will continue to flash A special safety device prevents the door from being opened immediately after the end of the cycle Wait for 2 minutes after the wash cycle has finished and the door locked light has gone out before opening the door As a safety measure check that there is no water evident in the drum At the end of the cycle turn the programme selector to OFF If the programme is paused the door locked indicator will go out after 2 minutes and the door can be opened Check there is no water evident in the drum before opening the door Digital Display DELAY START WASH CYCLE INDICATOR TIME SPIN ine SPEED if TIME DOOR LOCK WASH PROGRAMME START INDICATO
34. y ensures excellent washing results at minimum cost whilst respecting the environment Out of Balance protection This model is fitted with an electronic sensor device that checks if the load is balanced correctly If the load is slightly unbalanced the machine will re balance it automatically to then carry out the normal spin If after several attempts balance is not restored a reduced spin speed will be used If loads are seriously unbalanced the spin stage will be cancelled This helps limit vibration reduce noise and improve the washing machine s reliability and life Programme Selector For handling the various types of fabric and their level of OFF soiling in your laundry the washing machine has different programme groups according to type of wash temperature spin speeds and duration see Programme Guide Coloureds Cotton and Coloureds The Cottons programmes are designed for maximum washing g Synthetics and rinsing With spin cycles in between they guarantee the laundry is rinsed perfectly The final spin cycle ensures laundry is spun dry as much as possible up to the maximum speed Rapid 29 Cotton P Delicate The Cotton programme includes a Prewash cycle This option is particularly useful for heavily soiled loads and can be used independently of the main wash programme Detergent for this programme should be added to the first compartment of the soap drawer labelled I please refer to the section o
Download Pdf Manuals
Related Search