3 (continued) - Electrocomponents
Contents
1. prior to installing the new adapter card Refer to your computer user s manual for detailed data backup instructions For your records write down your system s current BIOS system setup settings before installing the adapter card Some system s BIOS may need to be set for add on IDE adapter or SCSI add on card Uninstall any hard drive installation software MaxBlast EZ Drive or Ontrack that may be on existing hard drives Failure to do so may result in loss of data This may be done after you ve installed the adapter card and hard drive Refer to the following URL if the existing hard drive is from Maxtor or Quantum http www maxtor com Click on the Product Support Knowledge Base link for additional information Warning Removing the installation software of hard drives other than Maxtor will result in data loss Please contact other hard drive manufacturers for their specific third party software removal procedures Fujitsu http www fujitsu com Seagate http www seagate com Western Digital http www wdc com ATAPI Devices DVD ROM Tape Backup If your ATAPI device is not UDMA 66 100 or 133 compliant and is currently functioning please leave it on that channel If your ATAPI device is not seen by its installation software when it is attached please call that device manu facture for new software Note f you re installing this adapter card along with a Maxtor hard drive please physica2. should appear 10 Power off your system and attach the hard drive s to the Ultra ATA 133 PCI Adapter Card Option C Installing Drivers during a Windows NT 4 x 2000 XP Fresh OS Installation 1 Depending on the type of Windows installation media you have perform one of the following OS installations Product Registration Take advantage of the benefits By registering your new Maxtor product you ll have the option to receive product updates special offers and valuable information about other data storage solutions from Maxtor a Floppy Install boot the system with the Windows NT installation disks b Floppy less Install boot from floppy and type WINNT B After the files have been copied the system will reboot On the reboot press the F6 key when the message Setup is inspecting your i la Simply point your web browser to www maxtor com computer s hardware configuration appears click on the Product Registration link and complete the short questionnaire c CD ROM Disk Install boot from the CD ROM disk and press the F6 key several times when the message Setup is Inspecting your computer s configuration appears 2 Press S to configure an additional adapter 3 Insert the MaxBlast Plus II CD into your CD ROM drive and launch the installer Then simply follow the screen prompts Product Warranty Maxtor s warranty obligations are limited to the terms set forth Maxto
3. Ultra ATA 133 PCI Adapter Card Installation Guide Pre Installation Thank you for selecting the Maxtor Ultra ATA 133 PCI Adapter Card Please follow these installation instructions to reap the full benefits of your purchase Handling Precautions If these handling precautions are not followed damage to the adapter card may result and your warranty may become void Please see the Warranty section for additional information Adapter cards are sensitive to electrostatic discharge ESD damage Handle the adapter card by its sides DO NOT touch the printed circuit board assembly E DON T connect disconnect any cables when the system power S IS on DON T force or rock the adapter card connectors into or out of their connection sockets System Requirements e Pentium class or higher with available PCI bus mastering expansion slot typically the first 3 PCI slots nearest to the processor Refer to system or motherboard guide for additional information Operating System Requirements e Windows NT 4 x SP4 or higher or Windows 98 Millennium Windows 2000 or Windows XP Tools Required for Installation e A small 2 Phillips screw driver e Your computer user s Manual e Operating system software Order of Installation The Maxtor Ultra ATA 133 PCI Adapter Card must be installed before the hard drive is installed Important Please Read e Make a backup copy of the files on any existing hard drive s
4. ettings menu select Control Panel 5 In the Control Panel window double click on the System icon Sgt ee i HE V J fig Duma Die jii Ee Sree mar Pe Geers ee ai T e Fl ip 1p r ere F Pea LH LLTI p mael bai ee a h i i Aa Mane aj Software Installation continued on reverse side Drive 0 Master black g UDMA Interface Cable industry standard cable length 18 inches Ultra ATA 133 PCI Adapter Card Installation Guide Software Installation continued Option A Installing Drivers with a New Windows 98 Millennium OS Installation 6 Inthe System window select Device Manager 7 In the hierarchical display under Other Devices is a listing for PCI Mass Storage Adapter Select it and then press the Properties button PEI Maa Uii ages F tel ides iT Ct Fa HE Dama Mat Faina isi Pb bdr bny iini Pire Mes He ia ee eee T neak Peh heres li ba ee hee eh ia T 8 Select the Driver tab in the Properties window choose Update Driver and then press Next Upeiate Device Diem Wiren l Thai mzae beah boa dapada Aveti for Wire E diii a4 133 E Caa A freee dees p ee pe h eee a lip myterratcabreate mni fearainn tem snore the jie of aa aihe Grete oe brimi REE a 9 Select Search for a better driver than the one your device is using now Recommended and press Next li
5. lly install both devices before using MaxBlast Plus I software Refer to the Maxtor ATA Hard Drive Installation Guide for specific instruc tions and drive jumper options Kit Components The Maxtor Ultra ATA 133 PCI Adapter Card comes complete with the compo nents shown here Please familiarize yourself with each of these items Ultra ATA 133 PCI Adapter Card UDMA IDE Interface Cable necessary for UDMA 66 100 133 devices MaxBlast Plus I Installation CD Hardware Installation Adapter Card Installation Installing the Ultra ATA 133 PCI Adapter Card in a system is a simple process The card fits into any available 32 bit PCI 2 1 compliant expansion slot on the system s motherboard 1 Turn off the power to your system and remove the system cover 2 Remove the inside slot cover of an available 32 bit PCI slot on the motherboard 3 Handle the Ultra ATA 133 PCI Adapter Card by its sides and install it into the open slot Figure 1 Figure 1 Installing the Adapter Card into a PCI Slot 4 If applicable attach the LED cable connector on your system case to the LED connector on the Adapter Card Figure 2 If your system LED connector does not light up try re connecting in the opposite direction Y IDE2 secondary IDE 1 primary LED connector o 32 pin PCI connector Figure 2 Adapter Card Connections 5 Fasten the adapter card bracket to the system case continued Wi
6. n two hard drives to the Ultra ATA 133 PCI Adapter Card you will need an additional UDMA interface cable Please visit your local Maxtor retailer and ask for the Maxtor Hard Drive Mounting Kit a Striped Edge Pin 1 A Adapter Connector blue Drive 1 Slave gray S Software Installation This section details software driver installation of the Ultra ATA 133 PCI Adapter Card when used with various operating systems Software drivers are program files that enable communication between devices such as the adapter card and an OS e Option A Installing Drivers with a New Windows 98 Millennium OS Installation e Option B Installing Drivers with a Pre Existing Windows 98 Millennium OS Installation e Option C Installing Drivers During a Windows NT 4 x 2000 XP Fresh OS Installation e Option D Installing Drivers with a Pre Existing Windows NT 4 x 2000 XP OS Installation Helpful Hint If upon booting your system doesn t recognize the adapter card change the card to a different PCI slot Again Maxtor recommends using one of the first 3 slots nearest to the processor Option A Installing Drivers with a New Windows 98 Millennium OS Installation 1 After installing the Ultra ATA 133 PCI Adapter Card and configuring the hard drive s partition and format your hard drive s 2 Install Windows 9x ME 3 After installation go to the Start menu and select Settings 4 From the S
7. ndows NT 4 x 2000 XP User Note Drives attached to the Ultra ATA 133 PCI Adapter Card cannot boot the Windows NT operating system OS without proper driver support If you re installing this adapter card into a system with an existing Windows NT OS do not connect any hard drives to the card before installing the driver soft ware Some systems may also require a BIOS change to SCSI add on card Hard Drive Installation 1 Configure the jumpers of the hard drive s you re preparing to install with the Ultra ATA 133 PCI Adapter Card with the appropriate master slave settings You may need to refer to your hard drive s manual for more information Note Do not apply any jumper that is meant to reduce the capacity of the hard drive 2 Install the hard drive s in the proper device bay of your system 3 Attach the UDMA IDE cable included in package to the hard drive s and to the IDE 1 connector on the Ultra ATA 133 PCI Adapter Card The colored edge of the cable indicates pin 1 Figure 3 The blue cable connector must be attached to IDE 1 on the Ultra ATA 133 PCI Adapter Card 4 If two drives are connected via the same cable make sure that one drive is configured as a master drive and connected to the black connec tor of the UDMA interface cable The other drive should be configured as a slave drive and connected to the gray connector of the UDMA inter face cable Note If you re connecting more tha
8. pite esre Crem Wired ae Oe ates ewe pated he GT F Famchha a bair ire thanthe one cherie i ang naa Neoah CO piai a bi o al e hin a aE 10 Insert the MaxBlast Plus II CD into your CD drive lodain Drree Dran Wirral Anes ell a bor rie chrr i dee Caisha on ae eed cares aed in args nd fe Lory mbade beeen Clee Het al ee ee D RDM give ta me fo o 11 Select the Next button A message informing you that Windows has found Maxtor Ultra ATA 133 Adapter should appear Option D Installing Drivers with a Pre Existing Windows NT 4 x 2000 XP OS Installation Hard drives should not be connected to the Ultra ATA 133 Adapter Card before performing the following procedure The Ultra ATA 133 Drivers must be loaded on the system hard drive running under the existing hard drive adapter before any hard drives are connected to the Ultra ATA 133 PCI Adapter Card NOTE Please refer to screen capture pictures listed in Steps 7 8 9 and 11 of Option A as they also apply for the steps outlined here in Option D Lhodlale Geevece Durem Wire ee int HE Site be ATA 3E Conta 1 Select Settings from Start menu Jie 2 Select Control Panel from the Settings menu Windows 2000 Note Go to the system properties then 12 Press Next then Finish then Yes when asked if the hardware tab and select device manager you want to restart your computer Be su
9. r warrants only to the original consumer purchaser that new Maxtor Ultra ATA 133 PCI Adapter Card products will be free trom defects in material and workmanship for 1 year from the date of original purchase For a replacement Ultra ATA 133 PCI Adapter Card the warranty on the replacement card is the remainder of the warranty on the original card or 90 days whichev er is longer If you discover a defect Maxtor will replace the Card at no charge to you provided you return it during the warranty period with transportation charges prepaid to Maxtor in Ireland Singapore or the USA Ultra ATA 133 PCI Adapter Cards must be properly packaged in Maxtor packaging or Maxtor approved packaging to obtain warranty service Before returning a Maxtor Adapter please contact Maxtor at 353 1 204 1111 in Europe or 1 800 2MAXTOR in U S to obtain a Return Material Authorization RMA number A copy of the receipt or a bill of sale bearing the appropriate Maxtor serial number and model number may be required for warranty service The warranty applies only to the Maxtor Ultra ATA 100 PCI Adapter Cards that can be identified by the Maxtor trademark trade name serial number or logo affixed to them Maxtor does not warrant any Card that is not manufactured by for or with permission from Maxtor This warranty is not applicable to Abnormal wear and tear Abuse unreasonable use mistreatment or neglect Damage caused during installation of the Card Damage caused by
10. re to remove gt Doublecice on ine SCS Ads ea pters icon which the MaxBlast CD from the CD ROM drive generates the SCSI Adapters dialog box 4 Choose Drivers and select Add Option B Installing Drivers with a Pre Existing Windows 98 Millennium OS Installation 5 Inthe Install Drivers menu select Have Disk 1 After installing the Ultra ATA 133 PCI Adapter Card 6 When Install From Disk appears insert the and configuring the hard drives power up the system MaxBlast Plus II CD into your CD ROM drive and and boot into Windows select OK 2 The Add New Hardware Wizard will appear 7 When the Install Driver dialog box appears select informing you that it has found a PCI Adapter Maxtor Ultra ATA 133 Adapter and select OK Refer to steps 3 through 9 of Option A for the remaining 8 When the Select SCSI Adapter Option box appears driver installation instructions select Install Driver Confirmation 9 After a successful installation the SCSI Adapter Setup box will show that the Maxtor Ultra ATA 133 To confirm that the driver was properly loaded select Adapter driver was installed Settings from the Start menu Select Control Panel and then double click on the System icon Choose the Device Manager tab and then click the in front of SCSI Adapters Maxtor Ultra ATA 133 Adapter
11. s you specific legal rights and you may also have other rights that vary from jurisdiction to jurisdiction Changes are periodically made to the information herein which will be incorporated in revised editions of the publication Maxtor may make changes or improvements in the product s described in this publication at any time and without notice Copyright 2001 Maxtor Corporation All rights reserved Printed in the U S A 9 01 MaxBlast Plus Il is a trademark and Maxtor is a registered trademark of Maxtor Corporation Other brands or products are trade marks or registered trademarks of their respective holders www maxtor com p n 20170100 rev A
12. the equipment or system with which the Card is used Damage caused by modification or repair not made or authorized by Maxtor Cards whose Maxtor Serial Number has been removed or defaced Damage caused by use of non Maxtor packaging Damage caused by improper or improperly used packaging Damage caused by lack of ESD protection Cards that are determined to be stolen THIS WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS WHETHER ORAL OR WRITTEN EXPRESSED OR IMPLIED MAXTOR SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FIT NESS FOR A PARTICULAR PURPOSE AND AGAINST INFRINGEMENT No Maxtor dealer agent or employee is authorized to make any modification extension or addition to this warranty MAXTOR IS NOT RESPONSIBLE FOR SPECIAL INCIDENTAL INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR UNDER ANY OTHER LEGAL THEORY INCLUDING BUT NOT LIMITED TO LOSS OF DATA LOSS OF PROFITS DOWNTIME GOODWILL DAMAGE OR REPLACEMENT OF EQUIPMENT AND PROPERTY AND ANY COSTS OF RECOVERING PROGRAMMING OR REPRODUCING ANY PROGRAM OR DATA STORED IN OR USED WITH MAXTOR DISK DRIVES OR MAXTOR S ULTRA ATA 133 PCI ADAPTER CARDS Some states jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or exclusions of implied warranties so the above limita tions or exclusions may not apply to you This warranty give
Download Pdf Manuals
Related Search