User Manual
Contents
1. Unit Xenon 9400103 Locknut for Xenon D2S 9400108 Transformer W Mounting Bracket for 9964 230 254 VAC 4386 Transformer W Mounting Bracket for 9964 110 VAC 4387 Rectifier For 9964 Xenon Helideck Light 3069 Cable Gland E204 3B M25 9mm Cable diameter 13 17 1mm 6143915 Complete Insert for TEF 9964 230 254V 3173 Complete Insert for TEF 9964 110V 3249 Complete Insert for TEF 9964 24V 4210 Tool for Replacing Xenon Lamp in TEF 9964 Helideck Floodlight 4676 Tool for Helideck Lights 4627 TECHNICAL DATA Material Acid proof stainless steel Safety glass Input voltage 254V AC 50 60Hz 230V AC 50 60Hz 110V AC 50 60Hz Power consumption 50Watt IP rating IP 66 67 according to EN 60529 Cable glands M25 Increased safety EEX E ll TAMB ATEX 20 C to 40 C CSA 20 C to 40 C Area of use Zone 1 Zone 2 and safe area Weight 11 5 kg2. EF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL REPLACING XENON LIGHT BULB Warning High voltage components inside lamp Make sure to disconnect power before opening Note To be performed by Ex certified personnel only 1 REMOVE FRONT RING Use front ring tool to loosen screw off front ring anticlockwise Holding Ra Distance bracket 3 SLIDE OUT LAMP INSERT Newer version 2 REMOVE HOLDING CLIP AND OR DISTANCE BRACKET Older version TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL 4A REMOVE LIGHT BULB NEW VERSION 4a 1 Disconnect the high voltage plug from the light bulb Position lamp removal tool over locking ring as shown below twist approx 30 degrees anti clockwise 4a 2 Remove xenon lamp Xenon lamp Locking ring 5 INSERT NEW XENON BULB 4B REMOVE LIGHT BULB OLD VERSION 4b 1 Disassemble the reflector unit 3 x M4 screws Disconnect the hight voltage plug 4b 2 Position lamp removal tool over locking ring as shown below Twist approx 30 degrees anti clockwise a 4b 3 Remove xenon lamp Xenon lamp Locking ring Note make sure the new xenon bulb is clean Do not touch the glass part of the bulb Mount lamp back together in reversed order TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL SPARE PARTS Part No Xenon Lamp D2S 35W For TEF 9964 9400074 Front Glass 3120 High Voltage Igniter
3. TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL IMPORTANT Read this instruction carefully before installing the product 170 m a l 79 O 39 218 196 1 l q 4xB10 5 130 p 180 _ _ 435 2 E R A 5 O f 215 iB ie o J a 196 130 a 218 ho TRANBERG Tranberg AS PO Box 8033 N 4068 Stavanger Norway Tel 47 51 57 89 00 Fax 47 51 57 89 50 E mail info tranberg com www tranberg com Tranberg Systems Hjulmagervej 15C 7100 Vejle Denmark Tel 45 75 85 83 80 E mail mail tranbergsystems com www tranbergsystems com TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL INTRODUCTION pele giaet Thank you for purchasing this product Regular tools required for installation For installation maintenance and assurance of a long life of this product please follow this manual e 17 mm wrench for assembling the floodlight e 13mm wrench for adjusting the angle of the light e 8mm flat screwdriver for open closing the cover of the junction box APPLICATIONS e 3 mm flat screwdriver for installing the cable in the oo terminal block e Floodlighting of helicopter landing areas e For use in hazardous areas e 5 5 mm
4. edition UL 542 1999 Eight edition UL 935 2001 Tenth edition ANSI UL 60079 0 2002 First edition ANSI UL 60079 1 2002 First edition ANSI UL 60079 7 2002 First edition TEF 9964 XENON HELIDECK FLOODLIGHT EEx de USER MANUAL RUBBER SEAL Cable diameter Size Part No 8 5 13 5mm O23 13x8mm 5002 0124 13 17mm O23 16x8mm 5002 0125 Be sure to install the cable in a way wich prevents water to penetrate into the enclosure through the cable gland also make sure to use the correct rubber seal when you install the luminaire INSTALLATION INSTRUCTIONS The floodlight should be installed according to the calculated light distribution plan The glass in front should face the centre at the helideck unless stated otherwise Secure the floodlight to the helideck by means of four M10 bolts Open the enclosure cover on rear Replace cable gland gaskets as required to match the cable diameter Unused cable glands should always be replaced with a blind plug Connect cables and replace the enclosure cover Exposed non current carrying metal is to be bonded to ground by a minimum 14 AWG 2 5mm copper wire 218 196 V Bottom 180 a 435 FER A A pgdu a ae p 1 iJ 150 218 170 el as fe Front Side T
5. flat screwdriver for removing the lamp insert e Floodlighting e 30mmwrench totightenthelocknutandthepressurenut e Hook screw key size 155 165 to open closing the front ring MAINTENANCE INSTRUCTIONS The luminaire should be inspected according to Company routines The manufacturer suggests regular check for water intrusion condensation which should be removed immediately Check the drain plug drain hole function CONTENT IN BOX When cleaning use only mild detergents Alcohol or l petroleum based products may damage lens paint or The product is fully assembled and ready for installation plastic components APPROVALS Certificate No Nemko OOATEX245 Complies with EN 500014 1997 A1 1999 A2 1999 EN 50018 1994 SAFETY PRECAUTIONS CSA EN 50019 1994 Note that changes made to the product and or installation International amp 216432 of components which do not conform to the approval Canada may be a safety violation The manufacturer will in no Complies with CSA Standard C22 2 No 0 M91 circumstance be held responsible for such activity CSA Standard C22 2 No 0 4 M1992 For your health and safety always use safety gear suited CSA Standard C22 2 No 43 M1984 for the task Be certain to follow codes regulations and or CSA Standard C22 2 No 250 0 00 specific procedures that are related to the installation CAN CSA Standard E60079 0 02 CAN CSA Standard E60079 1 02 CAN CSA Standard E60079 7 02 UL 1598 2000 First
Download Pdf Manuals
Related Search