THC-1002IR - Balter Security
Contents
1. the brightness of the peripheral area of the image You can set the mask value and threshold from 0 to 255 3 3 6 EFFECT EFFECT 1 COLOR GAIN 200 2 COLORHUE 200 3 SHARPNESS 25 4 CONTRAST 150 5 BRIGHT OFF 1 6 MIRROR ON 7 FLIP ON 8 RETURN RET Figure 3 5 EFFECT Color Gain Color gain adjust this feature to change the saturation of the color You can set the value from Oto 255 Color Hue You can adjust the image HUE from 0 to 71 Sharpness Sharpness determines the amount of detail that an imaging system can reproduce You can set the value from 0 to 255 Contrast Contrast enhances the difference in color and light between parts of an image You can set the value from 0 to 255 Bright Off Bright Off refers to the brightness compensation of the image You can set the bright compensation value as 0 or 1 Mirror You can set the Mirror status as ON OFF Flip You can set the FLIP status as ON OFF 3 3 7 SYSTEM SYSTEM 1 CAMERA ID 255 2 ID DISP ON 3 NAME DISP ON 4 LANGUAGE ENG 5 FACTORY INIT OFF 6 RETURN RET Figure 3 6 SYSTEM You can set the camera ID from 0 to 255 Select the ID display and name display status as ON OFF Chinese and English are selectable for the language of the menu You can restore the camera to the default by setting the factory initialization status as ON 3 3 8 EXIT Exit and Save amp exit are selectable www neostar de2. CAMERA STEPS 1 Wiggle the mounting plate to disassemble it from the wall mount Figure 2 4 Disassemble Mounting Plate 1 Drill the screw holes on the wall according to the supplied drill template 2 Attach the wall mount to the wall and tighten the screws to fix it Figure 2 5 Drill Template amp Install Mount Figure 2 6 Screw the Mounting Plate 5 Fix the camera to the wall mount with the supplied screws Figure 2 7 Fix the Camera 5 Adjust the surveillance angle 1 2 3 4 Loosen No 1 adjusting screw to adjust the pan position 0 360 Tighten No 1 adjusting screw Loosen No 2 adjusting screw to adjust the tilting position 0 90 Tighten No 2 adjusting screw Figure 2 8 Angle Adjustment 3 MENU OPERATION Menu CEE D aw fa 7 Great errect sen EXT CC e GD CO CF Cm CD GE Gorm o Com L HOLD HLC A AUTO 1 oome sooo Figure 2 1 Remove the Bubble 3 1 VIDEO OUT You can set the frame rate as 25 fps 30fps 3 2 DAY NIGHT Color B W AUTO and EXT are selectable for DAY NIGHT switches Under the mode of the AUTO and EXT you can set the IR LED as Smart and CDS If the IR LED is selected as Smart you can set the brightness of the IR LED DAY NIGHT AWB 1 MODE AUTO 1 MODE AUTO 2 DTON 63 2 R G GAIN 255 3 NTOD 63 3 B G GAIN 151 4 DELAY TIME 20 4 RETURN R
3. ET 5 RETURN RET j Figure 2 1 Bubble Figure 2 1 Remove the Bubble 3 3 3 AWB Auto User Push 8000k 6000k 4200k and 3000k are selectable for AWB Under the mode of AUTO you need to set the R G B G Gain and to select an indoor outdoor mode If the AWB mode is select as User You need to set the R G B Gain manually 3 3 4 AE You can set the AE mode as HOLD DC and ESC Brightness Brightness refers to the brightness of the image Shutter Shutter denotes the speed of the shutter You can set the shutter as AUTO 1 25 1 30 1 50 1 60 1 100 1 120 1 250 1 500 1 1k 1 3k and 1 10k Flicker You can set the flicker status as 50HZ 60HZ to prevent image flicking BLC BLC bases on the back area to enhance the brightness of the whole image You can set the BLC gain from 0 to 16 AGC AGC optimizes the clarity of image in poor light scene The value of AGC can be set from 1 5 LSC LSC corrects the phenomenon where theimage gets darkened or blurred on the periphery 3 3 5 SPECIAL SPECIAL 1 PRIVACY ZONE 2 MOTION 3 HLC 4 RETURN RET Figure 2 1 Remove the Bubble Privacy zone Select a PRIVACY area Set the MASK PAT as OFF GRAY WHITE or BLACK Set the SX EX SY EY value to define the position and size of the area Motion Set the Motion status as ON or OFF Set the SENSITIVITY from 0 to 255 Set the alarm status as ICON TRANCE OFF Set the hold time from 0 second to 255 seconds HLC HLC supplements
4. NEOSTAR THC 1002IR HD TVI BuLLET CAMERA User MANUAL www neostar de Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual Privacy Notice This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual Please refer to the product specification for camera parameters and functions REGULATORY INFORMATION FCC INFORMATION FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely t
5. f the camera and the mounting If the wall is the cement wall you need to insert expansion screws before you install the camera If the wall is the wooden wall you can use self tapping screw to secure the camera If the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself 2 1 CEILING MountING For Tyre Type 1 CAMERA STEPS 1 2 Drill the screw holes in the ceiling according to the supplied drill template Hammer the supplied plastic expansion bolt into the screw holes P Drill Template All Screw Holes for mounting base re Figure 2 1 Drill Template Route the cables to the cable hole and connect the corresponding power cable and video cable Fix the camera to the ceiling with the supplied screws MMMM Type Figure 2 2 Fix the Camera to the Ceiling www neostar de 4 Screw the mounting plate onto the camera 5 Adjust the surveillance angle 1 Loosen No 3 adjusting screw to adjust the panning position 0 360 2 Tighten No 3 adjusting screw 3 Loosen the No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 1 adjusting screw to adjust the azimuth angle of the image 0 360 6 Tighten No 1 adjusting screw N asc Figure 2 3 3 axis Adjustment 2 2 Warr Mountine For Type Ill
6. o a designated collection point For more information see www recyclethis info 1 INTRODUCTION 1 1 PRopuct FEATURES This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology It features high resolution low image distortion and low noise etc which makes it suitable for surveillance system and image processing system High performance CMOS sensor and high resolution bring high quality image Low illumination OSD menu parameters are configurable Support auto white balance auto gain control electronic shutter control Support image effect adjustment Unit transmission control Advanced 3 axis design meets different installation requirements 1 2 OVERVIEW 1 2 1 Overview oF Type CAMERA Mounting Base HD Video Cable et T m w Power Cable 1 2 2 Overview OF Type CAMERA HD Video Cable Power ie ae Sun Shield 2 INSTALLATION BEFORE YOU START Please make sure that the device in the package is in good condition and all the assembly parts are included Make sure that all the related equipment is power off during the installation Check the specification of the products for the installation environment Check whether the power supply is matched with your power output to avoid damage Please make sure the wall is strong enough to withstand three times the weight o
7. o cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conpitions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity STATEMENT This product and if applicable the C supplied accessories too are marked with CE and comply therefore with the applicable harmonized European sstandards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot Dd be disposed of as unsorted municipal waste in the European Union For proper recycling mm return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or t
Download Pdf Manuals
Related Search