Home

DES-3028/52 Series Firmware Release Notes - D-Link

1. incorrectly enabled when action was set to something else than protect 16 The icon for removing IKE SA was missing hence making it impossible to remove an IKE SA using the web user interface 17 DNS Blacklist CLI command showed wrong status of blacklist servers on inactive HA member Inactive HA member does not perform any anti spam inspection so the inactive node is unaware of the status of the blacklist servers 18 Email attachments with very long file names could cause memory corruption in the SMTP ALG 19 Log string sent to syslog receivers was not always correctly formatted Some log arguments were not separated by a whitespace resulting in invalid parsing by syslog receivers 20 When restarting an interface on the DFL 1600 or DFL 2500 there has been a theoretical possibility of memory corruption This issue has been fixed from F W v2 20 02 and later 21 Connections were under certain circumstances incorrectly dropped by the IDP scanning engine when audit mode was used 22 After IPSec tunnels were modified the reconfiguration of the gateway was not done correctly The result was that the gateway could go into unexpected abort state 23 A configured external log receiver that does not accept log messages might send ICMP destination unreachable packets to the firewall These packets would trigger new log messages resulting in high CPU utilization Logging is now connection based and the sending rate of log message
2. 2 27 00 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspects of ALGs are state synchronized This means that all traffic handled by ALGs will freeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA member cannot send log events over tunnels 6 Inactive HA member cannot be managed monitored over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels
3. 11 The SMTP ALG could not tell the difference between the new Microsoft Office 2007 document file types and file type ZIP This is because there is no difference that can be easily discovered the new Microsoft Office files are in fact ZIP files with a different extension An ALG configured to make file integrity checks would therefore signal these files as invalid wrong mime type wrong file suffix The ALG will now identify Office 2007 files as ZIP files Anti virus checks will if enabled scan the contents of the new Office 2007 files just like it would with a regular ZIP file IP address with suffixes 0 and or 255 could incorrectly be assigned to IPSec config mode clients Nested MIME bodies could in some scenarios be blocked by the SMTP ALG For example the SMTP ALG could block images inserted as inline with an error message indicating base64 decoding error The recipient received the email without the attached image but an error message saying The attachment xxxx has been blocked by the Security Gateway The ALG has been updated with better support for nested MIME blocks A user logging in via Web based user Authentication when configured to handle user credentials via one or several RADIUS servers it could cause an unexpected abort if no RADIUS server was reachable This issue has been fixed The web user interface the properties in Dynamic Black Listing were D Link NetDefend Firewall Firmware Release Notes
4. D Link NetDefend Firewall Firmware Release Notes NetDefendOS Version 2 40 04 Published Date 2013 07 17 Copyright O 2013 Copyright Notice This publication including all photographs illustrations and software is protected under international copyright laws with all rights reserved Neither this manual nor any of the material contained herein may be reproduced without written consent of the author Disclaimer The information in this document is subject to change without notice The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes Limitations of Liability UNDER NO CIRCUMSTANCES SHALL D LINK OR ITS SUPPLIERS BE LIABLE FOR DAMAGES OF ANY CHARACTER E G DAMAGES FOR LOSS OF PROFIT SOFTWARE RESTORATION WORK STOPPAGE LOSS OF SAVED DATA OR ANY OTHER COMMERCIAL DAMAGES OR LOSSES RESULTING FROM THE APPLICATION OR IMPROPER USE OF THE D LINK PRODUCT OR FAILURE OF THE PRODUCT EVEN IF D LINK IS INFORMED OF THE POSSIBILITY OF SUCH DAMAGES FURTHERMORE D LINK WILL NOT BE LIABLE FOR THIRD PARTY CLAIMS AGAINST CUSTOMER FOR LOSSES OR DAMAGES D LINK WILL IN NO EVENT BE LIABLE FOR ANY
5. Nl 3e 7 Office xIsm files were blocked by the SMTP ALG Encrypted xlsm files are embedded in an Office 97 2000 Compatible container which results in an incorrect file typ according to file integrity control The file integrity control has been updated to handle encrypted xlsm files 8 A faulty model check made the Switch Management not display all the switch ports in the WebUI for the DFL 860E model 9 The Realtek 8169 interface reported link down incorrectly This caused route monitor to not work properly Affects DFL 260E and DFL 860E 10 The HTTP ALG failed to load web pages from certain web servers correctly The HTTP ALG will now respond with a TCP RESET should the server continue to send packets after the client has closed the connection 11 Anti virus scanning of zip files containing files with a large compressed size could sometimes lead to unexpected behavior 12 Using HTTP web authentication with a RADIUS server as authentication source could in very rare scenarios cause the firewall to malfunction during save amp activate reconfigure 13 Two HTTP ALGs with the same name but with different case e g MYHTTPALG and myhttpalg could sometimes cause the firewall to freeze during save amp activate reconfigure 2 27 02 1 It was not possible to use User Authentication on IP4Group objects 2 Certain SIP server scenarios in REGISTER transactions made the firewall reject incoming SI
6. Corrected leap year problem where leap year day was added to January instead of February The log event no arp ID 04100007 firewall action text was previously route enabled the text is now corrected to route disabled Time unit seconds added to help texts in WebUI ALG SIP dialog and CLI command help ALG SIP An expired AV or IDP license in an HA environment could trigger unexpected behavior in the inactive cluster node Some web authentication scenarios could lead to unexpected behavior by the firewall The output text for the CLI command dns list was not formatted correctly when using SSH remote management The firewall did not handle lower and upper case correctly in some configuration scenarios where objects were named almost identically In some High Availability scenarios the HA setting ReconfFailoverTime was not obeyed resulting in a failover when deploying a configuration on the active peer before the ReconfFailoverTime was reached Cancelling the HA wizard would result in unexpected behavior of the firewall Affected models DFL 260E 860E In rare occasions closing down a SIP session could lead to an unexpected restart of the firewall The general stability of SSL VPN tunnels has been improved The deployment of new configuration could have a negative impact on the performance of Realtek 8169 interfaces Affected models DFL 260E DFL 860E Running SSL VPN on a shared IP in an HA cluster disconnected the client at
7. The situation would resolve itself after a timeout of about 50 seconds but would still cause severe traffic impairment in certain situations most noticeably HTTP traffic This change will by default loosen the restrictions when an attempt to reopen a closed connection is received ValidateSilent ValidateLogBad while still enforcing RFC correctness 11 The SMTP ALG could not tell the difference between the new Microsoft Office 2007 document file types and file type ZIP This is because there is no difference that can be easily discovered the new Microsoft Office files are in fact ZIP files with a different extension An ALG configured to make file integrity checks would therefore signal these files as invalid wrong mime type wrong file suffix The ALG will now identify Office 2007 files as ZIP files Anti virus checks will if enabled scan the contents of the new Office 2007 files just like it would with a regular ZIP file 12 IP address with suffixes 0 and or 255 could incorrectly be assigned to IPSec config mode clients 13 Nested MIME bodies could in some scenarios be blocked by the SMTP ALG For example the SMTP ALG could block images inserted as inline with an Moz NI link v D Link NetDefend Firewall Firmware Release Notes 14 15 16 17 18 19 20 21 22 23 24 25 error message indicating base64 decoding error The recipient received the em
8. 2010 DFL 260 860 1660 2560 2560G DFL 210 800 1600 A4 A5 for DFL 210 B1 for DFL 260 860 Mar 4 DFL 160 A1 A2 for all models A3 A4 A5 2 26 02 2010 DFL 210 800 1600 2500 for DFL 210 800 1600 2500 B1 DFL 260 860 1660 2560 2560G for DFL 260 860 Jan 29 DFL 160 A1 A2 for all models A3 A4 A5 2 26 01 2010 DFL 210 800 1600 2500 for DFL 210 800 1600 2500 B1 DFL 260 860 1660 2560 2560G for DFL 260 860 2 26 00 Sep 15 DFL 210 800 1600 2500 A1 for all models A2 A3 A4 A5 DS 2009 DFL 260 860 1660 2560 2560G for DFL 210 800 1600 2500 July 15 A1 for all models A2 A3 A4 for 2 25 01 28 2009 DFL 210 260 800 860 1600 2500 DFL 210 800 1600 2500 Jun 11 A1 for all models A2 A3 AA for 2 25 01 22 2009 DFL 210 260 800 860 1600 2500 DFL 210 800 1600 2500 Oct 21 A1 for all models A2 A3 A4 for 2 20 03 2008 DFL 210 260 800 860 1600 2500 DFL 210 800 1600 2500 Jul 10 A1 for all models A2 A3 A4 for 2 20 02 2008 DFL 210 260 800 860 1600 2500 DFL 210 800 1600 2500 D Link NetDefend Firewall Firmware Release Notes Upgrading Instructions Upgrading by using CLI via SCP protocol SCP Secure Copy is a widely used communication protocol for file transfer No specific SCP client is provided with NetDefendOS distributions but there exists a wide selection of SCP clients available for nearly all workstation platforms SCP is a complement to CLI usage and provides a secure means of file transfer between the administrato
9. DHCP Server now performs a route lookup if the reply is destined for a host address i e not an IP broadcast 4 HA setups with IDP scanning enabled packets could be lost during a failover 5 Some services were using the private IP in HA setups for communicating This RYE N72 D Link NetDefend Firewall Firmware Release Notes RVH 3e 10 12 13 14 15 is now changed and the shared IP is used 6 The DNS lookup of the IP address to a remote gateway failed under certain circumstances for IPSec interfaces 7 The CLI command for displaying updatecenter AV IDP update status did not show enough information It has now been improved 8 TCP connections could sometimes fail due to an incorrect sequence number check 9 A missing Content Transfer Encoding header field in e mails could sometimes cause the SMTP ALG session to malfunction With TCP sequence validation turned on closing existing connections would cause all subsequent attempts to reopen the same connection to be dropped with a log message about a bad sequence number The situation would resolve itself after a timeout of about 50 seconds but would still cause severe traffic impairment in certain situations most noticeably HTTP traffic This change will by default loosen the restrictions when an attempt to reopen a closed connection is received ValidateSilent ValidateLogBad while still enforcing RFC correctness
10. On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 10 The function StateKeepAlive of NAT Pool is not working ME D Link NetDefend Firewall Firmware Release Notes 2 26 02 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspects of ALGs are state synchronized This means that all traffic handled by ALGs will freeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA member cannot send log events ove
11. for the Web User Interface were rendered incorrectly resulting in artifacts on some web browsers 8 The SMTP ALG did not load all whitelist and blacklist entries if the number of entries were more than about 30 The entries that failed to load were silently ignored All configured whitelisted and blacklisted addresses are now loaded and filtered correctly 9 Users were not properly logged in when IPsec LAN to LAN tunnels were configured to require IKE XAuth This could cause an unexpected reboot Now the LAN to LAN case is properly handled by IKE XAuth 10 The L2TP PPTP Server overview grid did not have a column for Server IP 11 The dropdown to select the interface for OSPF Neighbor in the Web User Interface printed the name wrongly The dropdown code has been enhanced to handle this value correctly and print the proper name 12 The validation of the latency setting in the Host Monitor configuration was not correct The configured value was lowered to an incorrect value 13 The setup wizard only created the second of the two possible Syslog servers D Link NetDefend Firewall Firmware Release Notes The first Syslog server is now correctly created by the wizard 14 The min and preferred input fields had swapped position on the configuration page for IPsec Algorithms and IKE Algorithms in the Web User Interface The position of the input fields has been corrected 15 In the Web User Interface it was not po
12. in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA member cannot send log events over tunnels 6 Inactive HA member cannot be managed monitored over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 10 The function StateKeepAlive of NAT Pool is not working 11 SIP ALG Limited functionality on SIP ALG It supports three scenarios a Protecting local clients Proxy located on the Internet b Protecting proxy and local clients Proxy on the same network as clients c Protecting proxy and local clients Proxy on a DMZ interface A more detailed desc
13. reconfiguration due to the inactive node going active during reconfiguration A recent change in scp secure copy uses an end of option parameter that NE D Link NetDefend Firewall Firmware Release Notes was handled erroneously by the firewall causing scp connections to be closed unexpectedly 15 The add CLI command would in some cases add a new configuration object with errors and the set CLI command allowed the user to modify configuration objects by entering invalid values Now the behavior has been changed to not modify the configuration if the resulting change causes errors unless the force flag is specified 16 The CLI netobject command incorrectly printed IPv6 addresses in IPv4 format 17 It was not possible to disable sending out High Availablility cluster heartbeats on nodes The setting was not obeyed 18 The Web Content Filtering WCF server connection could stall after a reconfigure and fail to resolve new URLs The issue has been corrected along with additional server connection statistics for the httpalg wcfcache CLI command 19 Log messages containing routing information used invalid values 20 Using the H323 ALG could in rare circumstances lead to unexpected behavior 21 An error in the configuration module could in rare occasions lead to unexpected behavior during the deployment of a new configuration 22 The output of the CLI command ifstat has been extended to list the
14. relaying through the firewall in transparent mode is supported 2 DH Group and PFS can be configured on IPsec interfaces 1 The name of the authenticated user is logged together with the requested URL in HTTP ALG log messages 2 DFL 210 and DFL 800 support anti virus and dynamic web content filtering No new features in this version 2 25 01 28 This firmware version is positioned to replace v2 25 01 22 because the v2 25 01 will cause device into cycle reboot when IPSec encapsulation was set as Both Nl D Link NetDefend Firewall Firmware Release Notes 1 Added version check for external language files 2 Improved logging for Anti SPAM 3 New log message at failover triggered by linkmon 4 A new advanced setting has been added to control the number of RADIUScommunication contexts that can be used simultaneously 5 DNS name resolving uses the shared IP in High Availability setups 6 Added support for Host Monitor for Routing 7 Added command to handle language files on disk 8 Improved LDAP functionality 9 Redesign of the tuple value controller in the webUI 10 Display of network objects 11 Extended route monitoring capabilities 12 The IPsec status page has been improved 13 PCAP Recording 14 New advisory link in virus found log messages 15 The webUI has been extended to handle child objects in a tab 16 Support of custom monitor interval in Linkmonitor 17 ZoneDefense now supports DG
15. should now be used instead of and none instead of disable 13 Some malformed HTTP URLs were always blocked when scanning with IDP It is now possible to configure the way malformed HTTP URIs should be treated log drop droplog ignore 14 Previously ARP monitoring would be disabled if there was no gateway to monitor Nl ME D Link NetDefend Firewall Firmware Release Notes Nl 3e 15 Previously a route could not be configured to include its own gateway among hosts to monitor if the gateway address was obtained via DHCP 16 A missing anti virus signature database or a license file not allowing anti virus scanning resulted in all traffic sent through an anti virus enabled Application Layer Gateway to be blocked Even though this behavior guaranteed that un scanned traffic never passed through the gateway it could lead to unexpected interrupts in traffic flows 17 At shut down of the unit connected SSH clients were not disconnected 18 The interface status page could show corrupted driver hardware output when viewing VLAN interfaces VLAN interfaces have no driver or hardware information so this field is now left empty 19 Executing commands which used object arguments from within a script file did not work It is now possible to execute such commands from within script files 20 IP4HAAddress peer address was not shown in the WebUI and CLI address book views The HA peer address is no
16. 0 1 DFL 210 and DFL 800 remove IDP Maintenance Service Changes of MIB amp D View Module Support memory usage and TCP buffer usage monitoring Problems Fixed Firmware Problems Fixed Version 2 40 04 1 The IP protocols 33 and 48 were logged with incorrect names and IP protocols 131 to 142 were missing names The IP protocol list has been updated according to the current IANA definition 2 Syslog messages sent from the firewall did not follow the standard specified in RFC5424 A setting that enables sending Syslog messages according to RFC5424 has been added to the LogReceiverSyslog configuration object 3 Certain configurations related to one sub system could cause a security vulnerability 1 Routemon did not detect link state changes on some Realtek interfaces Affected models DFL 260E DFL 860Es The link status info for the Realtek interfaces disappeared after a reconfigure Affected models DFL 260E DFL 860E In some scenarios with IDP configured traffic of certain patterns could in rare circumstances be delayed It was not possible to connect multiple L2TP IPsec clients behind the same NAT gateway SNMP Interface Alias field was empty when selecting Comment in Interface Alias If L2TP clients with the same local IP address established IPsec tunnels shige NE D Link NetDefend Firewall Firmware Release Notes behind a NAT device there were sometimes problems with the c
17. 2TP IPSec tunnels to another DFL working in LAN 8 No aspects of the IDP signature states are synchronized in HA modes 2 30 01 1 Don t support the latest protocol used by oray net Peanut Hull clients 2 Transparent Mode won t in HA mode 3 ALGs won t synchronize states in HA mode 4 L2TP PPTP IPSec won t synchronize states in HA mode 5 The inactive node in an HA cluster cannot be reachable over IPSec PPTP L2TP and GRE tunnels 7 DFL cannot support redirecting L2TP IPSec tunnels to another DFL working in LAN 8 No aspects of the IDP signature states are synchronized in HA modes 2 27 03 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspects of ALGs are state NV NI link v D Link NetDefend Firewall Firmware Release Notes synchronized This means that all traffic handled by ALGs will freeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node
18. 5535 was used as destination port in the SIP service configuration 7 Specific scenarios using the PPTP ALG could sometimes cause an unexpected restart of the firewall 8 The log message sent when reclassifying a URL using Web Content Filtering showed the wrong category The log message has been updated to display the correct category 9 Web User Interface Activating a configuration that had deleted an item that was represented in the navigation tree would not automatically update the navigation tree This resulted in a navigation tree that did not correspond to the D Link NetDefend Firewall Firmware Release Notes running configuration 10 Checked checkbox properties that were disabled were unchecked when submitting data in the Web User Interface since information sent by a web browser is identical for an unchecked checkbox and a disabled checkbox The configuration engine now correctly remembers the state of disabled checkboxes when submitting data 11 The HTTP ALG MIME type check did not have support for OpenDocument Text Documents odt 12 Script execute did not allow the cc command to run without parameters The command has been updated 2 27 00 1 The IP4 Group object didn t handle excluded addresses correctly It s now possible to use excluded and included objects in the correct way 2 Certain SIP option messages with high values for the expires header field failed to be properly pars
19. 9 A misconfigured IPsec tunnel could in some scenarios cause the firewall to malfunction 60 The firewall sometimes restarted unexpectedly when using IDP Pipes 61 The LDAP client now handles authentication using PPP with CHAP MS CHAPv1 and MS CHAPv2 62 Adobe Illustrator ai files saved by recent versions of Illustrator did not pass the MIME type check performed by the Application Layer Gateways since they were identified as PDF files 63 Removing the use of DHCP on multiple interfaces could in some rare cases during reconfigure cause the firewall to perform an unexpected abort Protection has been added to the timeout handling routine of DHCP 64 HTTP ALG generated information pages e g Restricted site notice could get incorrectly cached by downstream proxy servers This could lead to proxy servers returning a cached error message even though no error page should be seen 65 The OSPF Interface was missing the network configuration parameter This caused problems in certain setups where IPsec tunnels configured with 0 0 0 0 0 as remote or local network If the network parameter is not set the network parameter is copied from the configured interface 66 The PPPoE client option Force Unnumbered PPPoE did not force Unnumbered PPPoE to be used 67 Under certain Traffic Sapping settings lower precedences stop forwarding traffic when higher precedences start forwarding traffic 68 Configurations containing names or comments
20. DAMAGES IN EXCESS OF THE AMOUNT D LINK RECEIVED FROM THE END USER FOR THE PRODUCT Content REVISION HISTORY AND SYSTEM REQUIREMENT eeee eene eene e nnne nen nns snnn bassin ss sette essa asas trn 2 UPGRADING INSTRUCTIONS e rere tene eo eter erre 3 UPGRADING BYJUSING GIIVIA SCGPIPROTOCOUS ccescececsvescsuetereecsuscreese rre de ERE T TDI UI RU D IUD URDU ETT 3 UPGRADINGIBYI USINGMVEB U IE S a ee ert E E EE MERE TIED 3 NEW 3 CHANGES OEEUNGTIONALITM S x ure oce e eS rere sce E EEAO Ea e Ve vr e Nee EUN E EE E 7 5 8 7 5 5 7 KNOWN F8 31 REFATEDIDOGCUNIENITATION ee eee enean 40
21. Nh D Link NetDefend Firewall Firmware Release Notes Revision History and System Requirement Firmware Date Model Hardware Version Version 2 40 04 Jul 17 DFL 1660 2560 2560G DFL 260E A2 Nub 2013 DFL 260E 860E A1 for all models 2 40 03 Apr 05 DFL 1660 2560 2560G DFL 260E A2 2013 DFL 260E 860E A1 for all models 2 40 02 Dec 15 DFL 1660 2560 2560G DFL 260E A2 OUR 2012 DFL 260E 860E A1 for all models Apr 15 DFL 1660 2560 2560G 2 40 01 201 DFL 260E 860E A1 for all models Oct 21 DFL 1660 2560 2560G 2 40 00 2011 DFL 260E 860E A1 for all models June 1 DFL 1660 2560 2560G 2 30 01 2011 DFL 260E 860E A1 for all models A1 for all models A2 for Ney 24 SEL 1660 0 GU S SEDE Dee 10789 0 2010 DFL 260E 860E DFL 210 800 1600 A4 A5 for DFL 210 B1 for DFL 260 860 A1 for all models A2 for 2 27 02 Sep 13 DFL 210 800 1600 2500 DFL 210 800 1600 2500 A3 for und 2010 DFL 260 860 1660 2560 2560G DFL 210 800 1600 A4 A5 for DFL 210 B1 for DFL 260 860 A1 for all models A2 for 2 27 01 July 5 DFL 210 800 1600 2500 DFL 210 800 1600 2500 A3 for Bes 2010 DFL 260 860 1660 2560 2560G DFL 210 800 1600 A4 A5 for DFL 210 B1 for DFL 260 860 A1 for all models A2 for 2 27 00 May 14 DFL 210 800 1600 2500 DFL 210 800 1600 2500 A3 for S
22. P calls 3 In some situations when using SMTP ALG with Anti Virus e mails with attachments would not be completely transferred resulting in a timeout The ALG Anti Virus feature now specifically logs failure to decompress encrypted zip files A setting to allow or deny encrypted zip files have also been added 4 The usage bars on the DHCP Server status page were not displayed correctly when leases reached 100 usage 5 ACK messages for non 2xx PBXs responses were not forwarded by the SIP ALG 6 The DHCP Server did not send DHCP NAK messages in all scenarios This change speeds up the process of receiving a new IP address lease in these scenarios 7 The SMTP ALG always allowed emails where the SMTP from address and email header from address did not match A new setting has been added which allows the administrator to deny or tag these mails as spam 8 CLI command ipsecdefines has been removed from techsupport command D Link NetDefend Firewall Firmware Release Notes oily 3e 9 During configuration certain values were not reset after parsing an IGMP Report rule which made the next IGMP Query misbehave The configuration values are now properly reset after parsing IGMP Report rules 10 Incoming SIP traffic routed through an IPsec tunnel was discarded by the SIP ALG 11 Some empty configuration values were not written to the configuration After a restart of the firewall the default values wer
23. S 3200 series switches 2 25 01 22 18 Anti Virus triggered ZoneDefense 19 LDAP Authentication 20 Route Load Balancing 21 Extended SIP Application Layer Gateway supporting new scenarios 22 TCP transport added to the SIP Application Layer Gateway 23 Multiple media connections for SIP Application Layer Gateway 24 PPTP server support for multiple PPTP clients behind the same NAT gateway 25 PPTP server and client have been extended to support stateful MPPE 26 Improved verification of 1 4 values 27 IDP Triggered Traffic Shaping 28 AVSE MaxMemory setting has been removed 29 Relayer IP address filter at DHCP Server 30 Support for VLAN priority derived from IP DSCP precedence 31 Gigabit Traffic Shaping Support 32 The PPPoE client has been changed to support unnumbered PPPoE 33 Improved server monitoring for Server Load Balancing 34 The ping CLI command has been improved 35 The schedule page has been improved 36 SSL TLS Termination 2 20 03 1 No new features were introduced in the 2 20 03 release Nl RU D Link NetDefend Firewall Firmware Release Notes 1 MTU can be configured for Interfaces 2 MTU can be configured for PPTP L2TP Client Interfaces Changes of Functionality Firmware Modified Features Version 1 The firmware 2 30 01 and latter would ONLY be applied on the current 2 30 01 platform DFL 260E 860E 1660 2560 2560G 2 26 0
24. ail without the attached image but an error message saying The attachment xxxx has been blocked by the Security Gateway The ALG has been updated with better support for nested MIME blocks A user logging in via Web based user Authentication when configured to handle user credentials via one or several RADIUS servers it could cause an unexpected abort if no RADIUS server was reachable This issue has been fixed The web user interface the properties in Dynamic Black Listing were incorrectly enabled when action was set to something else than protect The icon for removing IKE SA was missing hence making it impossible to remove an IKE SA using the web user interface DNS Blacklist CLI command showed wrong status of blacklist servers on inactive HA member Inactive HA member does not perform any anti spam inspection so the inactive node is unaware of the status of the blacklist servers Email attachments with very long file names could cause memory corruption in the SMTP ALG Log string sent to syslog receivers was not always correctly formatted Some log arguments were not separated by a whitespace resulting in invalid parsing by syslog receivers When restarting an interface on the DFL 1600 or DFL 2500 there has been a theoretical possibility of memory corruption This issue has been fixed from F W v2 20 02 and later Connections were under certain circumstances incorrectly dropped by the IDP scanning engine when audit mode was use
25. bute for LDAP Servers could not be empty It is now possible to create an LDAP Server with an empty Password Attribute field 9 The possibility to configure interface groups inside interface groups has been added 10 Routes monitored only by ARP were not marked as down when the link on the Ethernet interface was down Affected models DFL 260E and DFL 860E 11 Setting up a High Availability cluster using the backup and restore method would result in problems synchronizing the configuration because of an invalid interface configuration The units now correctly handle that interface configuration by using information from the old configuration 12 Large VLAN tagged packets would be dropped by the RealTek R8169 driver The driver has been updated to handle VLAN packets Affected models DFL 260E and DFL 860E 13 The RealTek R8169 interface reported wrong link speed for SNMP The interface has been updated to report the correct speed Affected models DFL 260E and DFL 860E 14 The RealTek R8169 driver contained a watchdog that erroneously triggered too often and made the interface restart The watchdog has been updated with a longer timer to prevent this from happening Affected models DFL 260E and DFL 860E 2 30 01 1 The firewall did not forward SIP registrations REQUEST with null values in the Authorization field 2 The source port 20 is occupied when combining the SAT Action in an IP rule with the FTP ALG 3 The CLI c
26. conds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 5 HA No state synchronization for L2TP PPTP and IPSec tunnels There is no state synchronization for L2TP PPTP and IPSec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 6 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover Related Documentation NetDefend Firewall User Manual v2 40 01 NetDefend Firewall CLI Reference Guide v2 40 01 NetDefend Firewall Logging Reference Guide v2 40 01
27. ction and User Authentication Rule 3 Static configuration objects default to their default values if the objects contain configuration errors This will prevent the firewall to misbehave due to configuration errors on static objects 4 The script command has been updated to handle adding objects with dependencies between each other 5 User authentication has been updated with a new authentication source that will grant access to the user without checking any credentials This functionality can be used to authenticate users from within login scripts etc to make auditing easier 6 All rule page layouts have been updated for how to enter the interface and network combination to be more intuitive 7 The data grid in the Web User Interface now displays information for simple objects as tooltip an example is a reference to an IPAAddress which would show the address value as a tooltip DFL 210 260 800 860 1600 1660 2500 2560 2560G 1 Added the possibility to disable and enable Ethernet interfaces using WebUser Interface 2 26 02 2 Separate icon for User Authentication enabled objects 3 Improved file names for backup packages including the configuration version number 4 Connection Rate Statistic Values can be viewed using SNMP DFL 210 260 800 860 1600 1660 2500 2560 2560G 1 The name of the authenticated user is logged together with the requested URL in HTTP ALG log messages 2 26 01 DFL 160 1 DHCP
28. d After IPSec tunnels were modified the reconfiguration of the gateway was not done correctly The result was that the gateway could go into unexpected abort state A configured external log receiver that does not accept log messages might send ICMP destination unreachable packets to the firewall These packets would trigger new log messages resulting in high CPU utilization Logging is now connection based and the sending rate of log messages will be decreased by the firewall when it receives ICMP destination unreachable packets regarding log receiver connections TCP connections with SYN relay were not synchronized correctly In case of HA failover traffic on these connections would freeze Unnecessary DynDNS and HTTP Poster re posts were triggered during RYE N72 27 D Link NetDefend Firewall Firmware Release Notes reconfigure This is now avoided by always considering if the local interface IP address has been changed or if the HTTP Poster DynDNS configuration has been changed 26 Some H 323 messages were incorrectly disallowed by the ALG The H 323 Status Enquiry message is now allowed to be forwarded through the H 323 ALG 27 The Fail Mode setting in the HTTP ALG was not honored by the Dynamic Web Content Filtering 28 The log message for expired or no valid Web Content Filtering license did only show up once There is now a log message generated once a one minute This should be more noticeable to t
29. d Firewall Firmware Release Notes synchronized This means that all traffic handled by ALGs willfreeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 5 HA Tunnels unreachable from inactive node The inactive node in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 6 Inactive HA member cannot send log events over tunnels 7 Inactive HA member cannot be managed monitored over tunnels 8 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 15 failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 9 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 10 HA No state synchronization for IDP signature scan states No aspects of the IDP signature state
30. d IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed Nl D Link NetDefend Firewall Firmware Release Notes non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 2 25 01 28 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspect of ALGs are state synchronized This means that all traffic handled by ALGs willfreeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA m
31. d Routing in Ethernet as well as VLAN interfaces 2 Remove restrictions on the number of HTTP posters All other network clients listed in Misc Clients also benefit from this restriction removal 3 Support authenticating users using the Ethernet MAC address over HTTP S 4 Update password field when focus is moved to a text input field which AN X D Link NetDefend Firewall Firmware Release Notes contains a password the field will now be cleared so the user can type in a new password directly 5 The WebUI page Reset now also contains a method for normal shutdown same action as the CLI command shutdown This method will gracefully close down tunnels hand over to other HA unit in HA scenarios and so on 1 Support SSL VPN feature 2 Support TLS renegotiation RFC 5746 in the TLS ALG 3 Increase the number of IDP signatures to up to 30 000 Configuration of up to 30 000 IDP signatures is now possible Affected models DFL 1660 2560 2560G 4 Add clone functionality to Web GUI It s now possible to create a copy of an object in the Web GUI by selecting Clone in the context menu in the data grids the edit page will pop up with information copied from the original object 2 30 01 5 Enhancement of services drop down menu The drop down menu for services has been enhanced to show port numbers 6 Enhanced IDP signature configuration It s now possible to select IDP signature groups from a v
32. e the average for the last 2 minutes 15 The ping verbose CLI command did not print the correct translated port if the packet was affected by a SAT rule in some cases 16 Some statistics on IXP interfaces were not correctly printed on the firewall console Affected models DFL 160 260E 860E 2 27 03 NEZ 1 The usage column in the DHCP Server status page has been updated to show active clients 2 References to UserAuth privileges for authenticated users could change when modifying the number of configured privileges 3 The web server could under certain conditions deadlock and print a 500 Internal Server Error message when trying to access the web user interface The web server has been extended with better error handling to prevent this kind of deadlock 4 The interface traffic counters were only of size 32 bit and often wrapped around when the throughput was high Corresponding 64 bit counters have been added to ensure that wrapping will not occur as often as the corresponding 32 bit values 5 The block list file verification failed for files with a size smaller than one packet The blocklist now validates the extension for the first packet when the content type could not be determined in the first packet 6 In certain scenarios the voice transmitted through the SIP ALG terminated suddenly two minutes after the call was established EY Ww D Link NetDefend Firewall Firmware Release Notes
33. e used instead 12 Some buttons in the web user interface had truncated text 13 The reception of 255 255 255 254 as Framed IP Address in a RADIUS negotiation wasn t handled correctly in all installations Now this will always lead to an IP being assigned to the PPTP L2TP client from the configured IP pool 14 It was not possible to click on the IDP signature group links in the web user interface page IDP Factory Signatures Clicking on the link now lists the signatures in the group 15 The DNS client always dropped DNS replies that had the truncated bit set The truncated bit indicates that the reply does not contain the complete response and that a new DNS request should be sent using TCP if the client supports TCP DNS The DNS client now uses the addresses in the partial response instead of ending up with no address at all 2 27 01 1 Certain SIP PBX configurations blocked media transmission on calls established between devices located on the same interface of the firewall 2 The POP3 ALG did not reset its state after a failed authentication This could cause the next login attempt to fail 3 Specific Intrusion Detection Protection IDP scenarios using hardware acceleration could cause scans to fail 4 Restarting a GRE interface did sometimes trigger an unexpected restart of the firewall 5 The POP3 ALG did not allow Digest MD5 authentication 6 The SIP ALG could forward malformed SIP messages if a range 0 6
34. ed When that occurred incoming calls to phones placed behind the firewall failed 3 Some HTTP headers could cause HTTP connections through the HTTP ALG to be closed down prematurely 4 On DFL 260 DFL 860 some specific high stressed Intrusion Detection and Protection scenarios using a hardware accelerator could drain the memory of the firewall 5 The SMTP ALG did not accept response codes that only contained numeric data 6 Browsing the Web User Interface over HTTPS would sometimes result in Error 500 Internal server error 7 On DFL 1600 DFL 1660 DFL 2500 DFL 2560 G after a reconfiguration using a HA configuration the interface synchronization list for the Inactive node contained invalid interface references which could cause problems when connections were synchronized before the list was rebuilt The references are now properly cleared during a reconfiguration 8 In the Web User Interface when defining an IDP Rule the check box to enable or disable the option Protect against insertion evasion attacks was not visible 9 The CLI techsupport command always sent a sesmgr file error log message even when it worked correctly The techsupport command now only sends log message when it fails 10 A limitation on the number of simultaneous WebAuth transaction could prevent the authentication of authorized users 11 The IP Rule view in the Web User Interface was slow when viewing large ye NI link v D L
35. ember cannot send log events over tunnels 6 Inactive HA member cannot be managed monitored over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 15 failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 2 25 01 22 1 If the IPSec encapsulation was configured as both when upgrade firmware to v2 25 01 22 it will cause device into cycle reboot This problem has been fixed in v2 25 01 28 2 The Oray net Peanut Hull client does not work after they changed the protocol 3 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 4 HA No state synchronization for ALGs No aspect of ALGs are state D Link NetDefen
36. for the SSH server in the web user interface Configuration support has now been added 22 There was a problem when multiple IPsec SAs referenced the same XAuth context 23 If a DHCP lease of a reserved IP address was manually released in the DHCP server and the host requested a new lease the host was not given the reserved IP again 24 The UDP checksum was not correctly updated when the multiplex rule was used together with address translation SAT SETDEST NAT 25 On some models a data alignment error in the Route Load Balancing system could cause the firewall to malfunction 26 Old configurations had an incorrect definition of the all tcpudp service Upgrading from an older version to a newer version could cause problems This problem has now been fixed and the old service will be converted during the upgrade 27 In some scenarios login attempts using the web user interface failed with the error message Error 500 Internal Server Error No new login attempts were allowed until the system had been restarted A synchronization lock for an internal buffer failed to reset during reconfigure and caused this issue 28 Scripts created by script create could previously have problems to run even when executed with script execute force because the generated script would sometimes incorrectly reference an object before it had been added This has been solved in such way that script create always generates a script that will not
37. g lini e D Link NetDefend Firewall Firmware Release Notes information The column shows which server that is the recommended server to use by the UTM services Anti virus IDP and Web Content Filtering The column has been renamed to Precedence and a server is either marked as Primary or Backup 29 PCAP captures on non Ethernet interfaces were missing Ethernet headers causing Wireshark to fail opening the files 30 The configuration user and session stored for the configuration changes sometimes indicated that the wrong user session stored the configuration Now the correct user session parameters are stored 31 In rare cases the Web Content Filtering feature could trigger an unexpected restart of the firewall 32 A lease for a static host in a DHCP server was removed if a new lease with the same MAC address was created A lease is now removed if the new lease is within the same DHCP server and has the same MAC address 33 The webUI memory logger search fields used partial matching The search fields are now using strict matching with the possibility to use the wildcards and 7 34 Outdated information was sometimes used when generating log events from the ALGs which could cause the device to restart 35 It was not possible to select Local ID for certificates Added configuration support for Local ID 36 Configuring the static IPsec config mode IP pool with an address range where the least sig
38. h Availability cluster nodes 6 The realm string for HTTP basic authentication was incorrectly not optional in the configuration 7 The unit for the OSPF memory max usage in the WebUI was kilobytes but has now been corrected to bytes 8 The Local Gateway configured in an IPsec tunnel was not shown in the CLI command ipsectunnels iface printout 9 The link status of the DMZ WAN1 and WAN2 interfaces on the DFL 860E model and DMZ and WAN on the DFL 260E would disappear shortly during the reconfigure process 10 The filename for an attachment was incorrectly required for the SMTP ALG and POP3ALG The ALGs have now been updated to handle attachments without filenames according to the RFCs ye NI link v D Link NetDefend Firewall Firmware Release Notes 11 12 13 14 15 16 The SIP ALG did not use the 420 Bad Extension response in certain circumstances The built in L2TP client did not work correctly when put behind a NAT device The configuration was not always updated correctly when upgrading to a newer version HTTPS webauth using Internet Explorer versions 8 and older did not show the logged in page after the user had logged in When using a large number of neighbors in nodes running OSPF there was a rare possibility of memory corruption A prompt was not added after various SSH printouts in the CLI 2 40 01 NEZ 10 11 12 13 14
39. he administrator 29 The SMTP ALG could in some scenarios cause instability to the system by losing track of SMTP state synchronization The SMTP ALG has been updated with improved state tracking and email syntax validation 30 It was not possible to configure the primary NBNS server for L2TP PPTP server interfaces in the web user interface 31 The TCP monitoring of Server Load Balancing did not increase TCP sequence number in the reset packet sent to server in case of connection timeout The sequence number is now increased by one 32 Server Load Balancing did not use All To One for port numbers When using a range on the service the destination port would be the specified port plus the offset from the low port number in the service 33 One of the log messages had an incorrect format When the log message was placed first in the log table the web user interface memlog would display an empty page 34 The description text for IP Pools incorrectly specified that IP Pools could be used by L2TP and PPTP 35 A confusing Anti Virus status message was visible in status page on non UTM capable devices The message has been removed 1 ICMP Destination Unreachable packets were not sent when UDP packets hit a Reject rule 2 Web authentication and web server connections were not closed correctly at reconfiguration 2 20 02 3 The DHCP Server did just send replies back on the receiving interface without regarding routing decisions The
40. her peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node in an HA NW P lli D Link NetDefend Firewall Firmware Release Notes cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA member cannot send log events over tunnels 6 Inactive HA member cannot be managed monitored over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there
41. id not increase TCP sequence number in the reset packet sent to server in case of connection timeout The sequence number is now increased by one Server Load Balancing did not use All To One for port numbers When using a range on the service the destination port would be the specified port plus the offset from the low port number in the service One of the log messages had an incorrect format When the log message was placed first in the log table the web user interface memlog would display an empty page The description text for IP Pools incorrectly specified that IP Pools could be used by L2TP and PPTP A confusing Anti Virus status message was visible in status page on non UTM capable devices The message has been removed Known Issues Firmware Known Issues Version 2 40 02 1 If the SSL VPN interface is configured with the outer interface any option SSL VPN will be disabled 2 Don t support the latest protocol used by oray net Peanut Hull clients 3 Transparent Mode won t in HA mode 4 ALGs won t synchronize states in HA mode 5 L2TP PPTP IPSec won t synchronize states in HA mode 6 The inactive node in an HA cluster cannot be reachable over IPSec L2TP and GRE tunnels 7 If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over VPN tunnels uses normal OSPF failover rather than accelerated 15 failover This mea
42. ink NetDefend Firewall Firmware Release Notes oily 3e collection of rules The rendering speed has been improved 12 Dropdown menus in the Web User Interface used a fixed width which caused objects with long names to push information outsize the window The dropdowns are now scaled to be able to show all the information The dropdown also automatically scrolls to the selected item when opened 13 The Mappings and Leases links on the DHCP Server status page in the Web User Interface didn t work 14 Disabling objects with references in the Web User Interface would delete the objects and references instead The objects are now only disabled when selecting to disable them 2 26 02 DFL 210 260 800 860 1600 1660 2500 2560 2560G 1 The range parameter in the rules CLI command did not work 2 The CLI command dns query only returned one IP address even though the DNS Record contained multiple entries 3 An error in the configuration engine caused problems when configuring the first OSPF Area for an OSPF Router Process 4 When using services with the SYN flood protection SYN Relay functionality enabled reconfigurations could result in unexpected behavior 5 Certain conditions sometimes led to an unexpected behavior when a firewall had IPsec tunnels configured 6 It was not possible to use User Authentication enabled objects in Routing Rules Threshold Rules IDP Rules or Pipe Rules 7 The log pages
43. is a small chance that the IDP engine causes false negatives during an HA failover 2 26 00 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspect of ALGs are state synchronized This means that all traffic handled by ALGs will freeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA member cannot send log events over tunnels 6 Inactive HA member cannot be managed monitored over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP an
44. ished The dynamic routes are now set properly for tunnels using DNS resolving of remote gateway 44 Certain device parameters such as the device name were previously synchronized between the members of a HA cluster To make it easier to distinguish between the members of a HA cluster these parameters are no longer synchronized 45 Route load balancing method spillover didn t take disabled routes into account 46 When reclassifying a Web Content Filtering blocked site the new category for the site was not immediately updated in the local cache It could take up to five hours before the cached entry was updated The local cache is now immediately updated once a site has been reclassified 47 When activating HA in the WebUI the browser was redirected to the shared IP address of the management interface Now the web browser is redirected to the private IP of the management interface 48 The HTTP ALG could fail to reconnect to Web Content Filter servers after a HA fail over The unit will now reconnect to the server when URLs need to be resolved 49 The TCP stack used by TCP based ALGs web based user authentication and remote management did not respond to SYNs with the window set to zero 50 The CLI command arp flush lt interface gt did not work It has now been corrected Flushing the ARP cache on all interfaces using arp flush did work though 51 The firewall did not respond to TCP Keep Alive packets 52 Management sessio
45. isual tree interface 7 Add lifetime for connection in the log messages 8 Warning for incompletely cloned objects When cloning objects that contain properties which cannot be cloned an alert will be displayed 9 Support for dynamic server addresses in SSL VPN The SSL VPN server has been updated to support the sending of an optional domain name FQDN to the client that will be used to connect to the server 1 The D Link DES 3528 switch can now be used by ZoneDefense 2 A new log message has been added indicating that an ARP resolve query 2 27 02 failed 3 The following browsers are now supported Firefox 3 Opera 10 5 Safari 3 Internet Explorer 7 and Chrome 4 1 A confirmation question will be prompted if the user attempts to execute a 2 27 01 CLI command that may cause system delays 1 Grouping configuration objects into logical groups makes it easier to manage large number of configuration objects It is also possible to add a descriptive description and custom color to distinguish what these objects do This grouping functionality is only for presentation and does not affect the existing functionality 2 Logging enabled by default on rules for the following objects Access DHCP Nl 3e D Link NetDefend Firewall Firmware Release Notes Server DHCP Relay Routing Rule Dynamic Routing Policy Rule IDP Rule Action IP Rule OSPF Router Process Threshold A
46. nificant byte of the last address in the range is smaller that the least significant byte of the first address in the range would cause the device to reboot when several tunnels are established One example of such a range is 172 16 1 240 172 16 2 40 37 Route Fail Over status information was faultily printed on the console every time the state of the route changed These printouts are now removed and only the log events remain 38 Changing the high availability setting use unique shared MAC could make both nodes of a high availability cluster go active 39 There was a dependency between link monitors which resulted in that the effective ping interval was reduced for each new link monitor configured 40 The CLI was missing a quick and easy way to list the available runtime services A services CLI command has been added This command lists the runtime values of configured services 41 It was not possible to send IKE messages through an IPsec interface The result was that a pair of hosts could not establish an IPsec tunnel with each other SW Ww D Link NetDefend Firewall Firmware Release Notes using IKE if the negotiation needed to pass through an IPsec tunnel established by the firewall and a peer 42 Netobject groups were not updated if the groups contained a dynamically changed DHCP etc address 43 IPsec tunnels using DNS resolving of the remote gateway could sometimes not be establ
47. ns 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings wily NE D Link NetDefend Firewall Firmware Release Notes No aspects of the IDP signature states are synchronized in HA modes 2 40 01 If the SSL VPN interface is configured with the outer interface any option SSL VPN will be disabled 10 Don t support the latest protocol used by oray net Peanut Hull clients 11 Transparent Mode won t in HA mode 12 ALGs won t synchronize states in HA mode 13 L2TP PPTP IPSec won t synchronize states in HA mode 14 The inactive node in an HA cluster cannot be reachable over IPSec PPTP L2TP and GRE tunnels 15 Ifthe cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over VPN tunnels uses normal OSPF failover rather than accelerated lt 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 16 No aspects of the IDP signature states are synchronized in HA modes 2 40 00 1 Don t support the latest protocol used by oray net Peanut Hull clients 2 Transparent Mode won t in HA mode 3 ALGs won t synchronize states in HA mode 4 L2TP PPTP IPSec won t synchronize states in HA mode 5 The inactive node in an HA cluster cannot be reachable over IPSec PPTP L2TP and GRE tunnels 7 DFL cannot support redirecting L
48. ns to the WebUI could on low throughput links timeout before the web pages have been fully loaded The timeout of the sessions has been increased in order to better handle this scenario 53 A leak of addresses in the static IPsec config mode IP pool caused the number of addresses available to clients to shrink over time It could also cause the device to reboot itself 54 IPsec config mode configured with a static IP pool did not in general hand out the last address in a range to clients 55 Log messages were not throttled correctly when the configured log receiver Moz NI link v D Link NetDefend Firewall Firmware Release Notes was offline and in return sent ICMP destination unreachable packets to the gateway This made the gateway trigger more log messages which could lead to drained CPU resources 56 IPsec config mode configured with multiple subnets or a static IP pool with multiple ranges of addresses falsely treated unchanged configurations as changed during reconfiguration and disconnected all tunnels 57 Using Web Content Filtering users were incorrectly displayed the access has been denied page if their HTTP request was generated while the WCF server connection was establishing The URL category lookup request is now silently queued and sent to the WCF server once the connection has been established 58 The HTTP ALG blocked web pages with malformed charset statement in HTTP headers 5
49. ociated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA member cannot send log events over tunnels 6 Inactive HA member cannot be managed monitored over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses Nl D Link NetDefend Firewall Firmware Release Notes normal OSPF failover rather than accelerated 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 10 The function StateKeepAlive of NAT Pool is not working
50. ommands reset configuration and reset unit show incorrect default management IP 4 SIP ALG would close SIP calls two minutes after the call session was established in some network scenario 5 The Route Type in OSPF Actions was incorrectly interpreted by the firewall when the configuration was activated 6 An unexpected restart could occur during a configuration deployment when new IPSec tunnels were added to the configuration Nl 3e D Link NetDefend Firewall Firmware Release Notes 7 It was not possible to use all address object combinations in places like routes or in the Address Book 8 The severity for the log message sslvpn max sessions reached was incorrectly set to DEBUG but has been changed to NOTICE 9 IPAGroups containing Userauth configured objects were not available for selection in IPRules The IPRules have been updated to allow IP4Groups containing objects with Userauth 10 The TLS ALG rejected SSL HELLOs with zero or more than one compression method 11 Some cipher suite combinations prevented the AES256 algorithm to be used when establishing SSH administration sessions to the firewall 12 Some specially crafted SDP payloads could cause unexpected reboots of the firewall 13 The edit alternative for Comment Groups was not shown 14 The Web GUI page for interface status showed the Send Rate and Receive Rate as average for the last 24h The values have been updated to us
51. onnections 7 The OSPF routes database was not updated during reconfigure in some High Availability scenarios 8 In some unusual circumstances the use of XAuth based authentication would lead to an unexpected reboot 9 The web user interface was not 100 compatible with Explorer 10 The basic structure has now been updated to render the page correctly in all major browsers 10 The firewall Dynamic Routing Rules did not properly export import OSPF routes when they were filtered by OSPF Tag range or Router Type 11 Afew log message categories such as SSL VPN and IPv6 Neighbor Discovery were missing from the log message exception list 12 In some scenarios when using IPsec with XAuth ESP delete notifications would not be sent 2 40 02 1 In some rare occasions the memory consumption of the firewall could increase unexpectedly when deploying cluster configurations 2 Theoutput list from the CLI command vlan was not sorted in VLAN ID order This has been corrected and the command was enhanced with the parameters to segment long output lists num and page 3 The blacklist CLI command did not set the correct port number and destination URL in its output 4 A configuration with the now obsolete selection of Log And Event Receiver category 36 USAGE would send out empty log data The configuration is now silently updated to exclude this category 5 The shared IP was not used in LDAP server queries for Hig
52. r s workstation and the NetDefend Firewall Various files used by NetDefendOS can be both uploaded and downloaded with SCP This feature is fully described in Section 2 1 6 Secure Copy of NetDefend Firewall v2 40 01 user Manual Upgrading by using Web UI For detailed installation and upgrade instructions please refer to the Firmware Upgrades chapter in the NetDefend Firewall v2 40 03 User Manual New Features Firmware New Features Version 2 40 03 1 Added the DHCP server when used with MAC address authentication to enable automatic logout of users When an IP address is being reused from the DHCP server and the old user was logged in via MAC authentication the DHCP server sends a logout message to log out the old user from the system 2 Added IPA as recognized MIME type 3 Support for hardware acceleration of IKE negotiations for DFL 2560 2560G to offload the CPU and make IPsec setup faster 2 40 02 No new features are introduced in the 2 40 02 release 2 40 01 1 Support the Cisco IPSec client on iPhone 2 Double Web Content Filtering local cache size on all models to accommodate more categorized sites 3 Support CHAP MS CHAP MS CHAPv2 and No authentication mechanisms for SSL VPN 4 Web Content Filtering Configuration Improvement When filtering override is enabled it is now possible to enter a custom timeout of the override period 1 Support for IPv6 in routing IPRules and Policy Base
53. r tunnels 6 Inactive HA member cannot be managed monitored over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 10 The function StateKeepAlive of NAT Pool is not working 11 The DUT would be crash and reboot after restart the GRE interface 2 26 01 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspects of ALGs are state synchronized This means that all traffic handled by ALGs will freeze when the cluster fails over to the ot
54. red over tunnels 7 OSPF If the cluster members do not share a broadcast interface so that the inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 1s failover This means 20 30 seconds with default settings and 3 4 seconds with more aggressively tuned OSPF timings 8 HA No state synchronization for L2TP PPTP and IPsec tunnels There is no state synchronization for L2TP PPTP and IPsec tunnels On failover incoming clients will re establish their tunnels after the tunnels are deemed non functional This timeout is typically in the 30 120 seconds range 9 HA No state synchronization for IDP signature scan states No aspects of the IDP signature states are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 10 The function StateKeepAlive of NAT Pool is not working 2 27 01 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspects of ALGs are state synchronized This means that all traffic handled by ALGs will freeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and ass
55. reference an object before it has been created Circular dependencies are resolved by first adding the objects without the problematic references then later modifying the object to its final state 29 Since the web user interface uses UTF 8 encoding a PSK containing ASCII characters with value of 128 255 would be stored as UTF 8 characters UTF 8 characters are now converted back to ASCII characters when it is possible 2 25 01 28 1 If the IPSec encapsulation was configured as Both then upgrade firmware to v2 25 01 22 it will cause device into cycle reboot 2 The WCF tab is shown on Non UTM Firewall models Basically Non UTM firewalls don t support dynamic WCF feature It is no longer visible on non UTM firewall models after upgrade to firmware v2 25 01 28 3 Startup Wizard is not displayed after reset configuration to default via WebGUI D Link NetDefend Firewall Firmware Release Notes 2 25 01 22 1 The advanced setting Block0000Src Drop DropLog Ignore Log has been renamed toLog0000Src Drop DropLog The actions Log andIgnore have now been converted into DropLog and Drop 2 UpdateCenter caused problems in HA setups sometimes locking up an HA node HA alsocaused some problems for pseudo reassembly 3 The behavior of the TCP reassembly has been changed slightly to avoid causing orcontributing to ACK loops 4 The firewall could generate multicast ethernet ip address mismatch log message
56. ription and network topologies can be found in the Admin Guide Any scenario different from these three might be difficult to deploy 12 SIP ALG Limited functionality on IP telephony It is not support all functionality in RFC 3261 or other RFC s that is referred to from RC 3261 There may be third party SIP aware units that cannot be configured to be compatible with the SIP ALG 2 27 02 1 The Oray net Peanut Hull client does not work after they changed the protocol 2 HA Transparent Mode won t work in HA mode There is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGs No aspects of ALGs are state synchronized This means that all traffic handled by ALGs will freeze when the Nl RU D Link NetDefend Firewall Firmware Release Notes cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive node The inactive node in an HA cluster cannot communicate over IPsec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node 5 Inactive HA member cannot send log events over tunnels 6 Inactive HA member cannot be managed monito
57. s are synchronized This means that there is a small chance that the IDP engine causes false negatives during an HA failover 2 20 03 1 The Oray net for Peanut Hull DDNS client does not work after supplier changed the protocol 2 HA Transparent Mode won t work in HA modeThere is no state synchronization for Transparent Mode and there is no loop avoidance 3 HA No state synchronization for ALGsNo aspect of ALGs are state synchronized This means that all traffic handled by ALGs will freeze when the cluster fails over to the other peer if however the cluster fails back over to the original peer within approximately half a minute frozen sessions and associated transfers should begin working again Note that such failover and consequent fallback occurs each time a new configuration is uploaded 4 HA Tunnels unreachable from inactive nodeThe inactive node in an HA cluster cannot communicate over IPSec PPTP L2TP and GRE tunnels as such tunnels are established to from the active node Inactive HA member cannot send log events over tunnels Inactive HA member cannot be managed monitored over tunnels OSPF If the cluster members do not share a broadcast interface so that the Nl i D Link NetDefend Firewall Firmware Release Notes inactive node can learn about OSPF state OSPF failover over tunnels uses normal OSPF failover rather than accelerated 1s failover This means 20 30 se
58. s if itwas deployed in setups where another HA cluster was present The heartbeats from the other HA setup were not recognized and triggered a log message Heartbeats from other HA setups are now identified and silently dropped 5 Configuration errors in SSH management setup were not reported to the user 6 Ability to configure a source port for a NAT rule has been removed This could be configured but would be ignored and the source port would still be randomly selected 7 Log messages regarding denied update of anti virus or IDP signatures were incorrectly generated when no valid subscription existed for that service The log messages have been removed 8 Redirecting HTTP users to the web authentication login page did not work correctly 9 A change of an interface s name could lead to the drainage of free buffers that eventually caused the firewall to stop handling traffic The root cause of the leakage has been identified and fixed 10 The functionality of the CLI command urlcache has been moved into the httpalg wcfcache command The new httpalg flag wcfcache lists the hosts which have overridden the content filter 11 A predefined list of file types were missing in the configuration for ALG file integrity and anti virus scan exclusion Specifying the file extensions can now be done with support of a list of extensions 12 The arguments to the CLI command arpsnoop have been changed To enable snooping on all interfaces all
59. s will be decreased by the firewall when it receives ICMP destination unreachable packets regarding log receiver connections 24 TCP connections with SYN relay were not synchronized correctly In case of HA failover traffic on these connections would freeze 25 Unnecessary DynDNS and HTTP Poster re posts were triggered during reconfigure This is now avoided by always considering if the local interface IP address has been changed or if the HTTP Poster DynDNS configuration has been changed 26 Some H 323 messages were incorrectly disallowed by the ALG The H 323 Status Enquiry message is now allowed to be forwarded through the H 323 ALG 27 The Fail Mode setting in the HTTP ALG was not honored by the Dynamic Web Content Filtering 28 The log message for expired or no valid Web Content Filtering license did only NV NI link v D Link NetDefend Firewall Firmware Release Notes 29 30 31 32 33 34 35 show up once There is now a log message generated once a one minute This should be more noticeable to the administrator The SMTP ALG could in some scenarios cause instability to the system by losing track of SMTP state synchronization The SMTP ALG has been updated with improved state tracking and email syntax validation It was not possible to configure the primary NBNS server for L2TP PPTP server interfaces in the web user interface The TCP monitoring of Server Load Balancing d
60. shared MAC addresses on the interfaces of High Availability cluster nodes 23 Passwords for newly added users were not encrypted in the configuration file 24 OSPF MD5 authentication misbehaved when using ID other than 2 25 The RADIUS accounting session ID string could under some circumstances be reused for a later session 26 A prompt was not printed in the CLI after activating a new configuration 27 Arecent security patch for CVE 2011 3389 in some popular web browsers made the firewall s SSL VPN client download page unreachable 2 40 00 1 Some VPN configurations using Radius Accounting did not report in out octet statistics to the Radius Accounting server 2 The H 323 ALG did not allow FACILITY messages to be sent during the ALERTING state 3 In certain scenarios traffic originating from LDAP could lead to unexpected behavior by the firewall 4 If SSL VPN was configured to listen on a proxy ARPed IP it was not possible to log in to the SSL VPN portal ye NI link v D Link NetDefend Firewall Firmware Release Notes 5 Browsing to certain pages in the WebUI would lead to unexpected behavior for the firewall Affected models DFL 260E and DFL 860E 6 Some scenarios made the firewall send malformed packets in an SSL negotiation 7 In a High Availability scenario it was not possible to log in to the firewall in order to download the SSL VPN client 8 The value Password Attri
61. ssible to change order of objects that were both disabled and deleted It s now possible to move objects that are both disabled and deleted DFL 160 1 Enabling POP3 on the Inbound Traffic page did not have any effect 2 26 01 DFL 210 260 800 860 1600 1660 2500 2560 2560G 1 A configuration that contains a routing table loop could lead to the watchdog being triggered Now the configuration will fail to be activated with the following message Dynamic routing configuration error possible configuration loop 2 Setting both IKE Lifetime and IPsec Lifetime to 0 seconds in an IPsec tunnel triggered a warning message on the console referring incorrectly to another property 3 Proposal lists were not properly listed in command line ipsectunnel iface output 4 When using a user authentication rule for HTTPS with LDAP an SSL socket was sometimes not closed possibly resulting in instability 5 It was not possible to use certificates that had no alternative name set 6 Due to memory corruption occurring in some setups the internal timers caused the firewall to restart unexpectedly Depending on the traffic load the reboots occurred periodically from a few hours up to several days This issue has been corrected together with fixes in the loader 7 The establishment of SYN flood protected TCP connection could be unnecessarily delayed due to the firewall dropping all the packets sent by the client side while waiting for
62. t being dropped when the connection to the server isn t established and this leads to a three seconds delay The connection from the ALG to the client will now not be initiated D Link NetDefend Firewall Firmware Release Notes until the server connection is established towards the ALG 6 It was not possible to move a rule up or down in the list if the rule was disabled 7 The command ipsecstats could in some circumstances not show all tunnels when a tunnel name was given as an argument The command now displays all the tunnels when tunnel name is given as an argument 8 The command ipsecstats only listed the first matching IPsec SA when a tunnel name was given as an argument The command now displays all IPsec SAs that are connected to the specified tunnel name 9 The FTP ALG virus scanner triggered an unexpected restart if the virus signature database was updated while files were being processed by an FTP ALG configured with fail mode set to allow 10 The ippool show CLI command output showed all configured pools which could be a very long list Now only the first ten are listed by default The max lt num gt option can be used to display more items 11 The SIP ALG didn t handle 183 Session Message when initiating a new SIP call 12 The return traffic for ICMP messages received on an IPsec transport mode interface was wrongly routed to the core itself and then dropped The return traffic is no
63. t panel display could stop after showing the first sensor under certain conditions when Hardware Monitor was enabled The system information slides can now loop through all pages without getting stuck Only affected hardware models with front panel display 15 There was a critical defect in the Web Content Filter functionality that could cause the firewall to reboot unexpectedly DFL 160 1 It did not work to have DHCP assigned IP on the WAN interface and at the same time relay DHCP requests to hosts on the LAN or DMZ in transparent mode 2 If the Internet connection had dynamic IP address DHCP enabled and transparent mode was used on LAN or DMZ the IP address on the LAN DMZ interface was set to 0 0 0 0 2 26 00 1 PPP negotiations were sometimes slower than necessary 2 Deploying a configuration during heavy traffic load could cause a watchdog reboot 3 It was possible to enable the anti spam feature DNSBL on an SMTP ALG without specifying any DNSBL servers Configuring DNSBL without specifying any servers will now give an error 4 Some errors in IPsec tunnel configuration were not correctly treated during the firewall start up process resulting in IPsec tunnels not properly being set up Now most of those errors make the tunnel be disabled and a warning message be displayed For the most severe ones the configuration will be rejected by the system 5 Running FTP ALG in hybrid mode could result in the first packe
64. the completion of the three way handshaking between the firewall and the server 8 Updates of the Anti Virus database could only be done when the Anti Virus functionality was enabled The database can now be updated even though no Anti Virus functionality is enabled 9 The license page showed an incorrect value for maximum number of PPP tunnels 10 Running certain sequences of CLI commands or performing corresponding actions in the Web User Interface involving multiple reject commands could cause a critical malfunction in some cases Nl ME D Link NetDefend Firewall Firmware Release Notes Nl Si 11 After running the CLI command reject with a configuration object as parameter activation of configuration changes could fail with an error message but show errors would say that there were no errors The Show errors command has been updated to correctly display these errors 12 Keep alive SIP pings were not handled correctly and would generate drop logs The SIP pings are now handled correctly and a response pong is sent 13 The console command always printed that it showed the events for the last 30 days even though nothing had happened The command has been updated so it will print the date of the oldest entry If entries exist that are older than 30 days it will print 30 days and truncate if less than 30 days date of last entry will be printed 14 The system information slides on the fron
65. using certain special characters could cause the firewall to fail reading the configuration during startup SW Ww D Link NetDefend Firewall Firmware Release Notes 1 ICMP Destination Unreachable packets were not sent when UDP packets hit a Reject rule 2 Web authentication and web server connections were not closed correctly at reconfiguration 3 The DHCP Server did just send replies back on the receiving interface without regarding routing decisions The DHCP Server now performs a route lookup if the reply is destined for a host address i e not an IP broadcast 4 HA setups with IDP scanning enabled packets could be lost during a failover 5 Some services were using the private IP in HA setups for communicating This is now changed and the shared IP is used 6 The DNS lookup of the IP address to a remote gateway failed under certain circumstances for IPSec interfaces 7 The CLI command for displaying updatecenter AV IDP update status did not show enough information It has now been improved 8 TCP connections could sometimes fail due to an incorrect sequence number check 9 A missing Content Transfer Encoding header field in e mails could sometimes cause the SMTP ALG session to malfunction NT 10 With TCP sequence validation turned on closing existing connections would cause all subsequent attempts to reopen the same connection to be dropped with a log message about a bad sequence number
66. w displayed in address book listings 21 Idling system backup download for more than 5 seconds aborted the download It is now possible to idle up to two minutes without having the download being aborted 22 When the SMTP ALG anti virus engine detected multiple infected files within a single ZIP file the name of the zip file was incorrectly added to the BlockedAttachments txt file each time a virus was found The zip file name is now only added once no matter of the number of infected files within the zip file 23 An HA node sometimes froze and had to be physically rebooted after updating IDP signatures via updatecenter 24 The authentication method for IPsec tunnels was set to PSK as default value When adding such tunnels from the CLI this was unclear When using the CLI to create IPsec tunnels the user must now explicitly specify the wanted authentication method 25 Microsoft Windows LT2P over IPsec sessions could fail in the sequence of re keys 26 When using the CLI it was possible to add objects to already disabled folders It is no longer possible to add objects to disabled folders 26 The User Authentication logs sometimes contained faulty authentication information Log events were also missing in some authentication scenarios 27 A file transfer scanned by the HTTP ALG with anti virus activated could be aborted after a WindowZero event from the client 28 The active column of updatecenter servers command showed misleadin
67. w passed back using the same connection as it arrived on 13 Tab completion in the command line interface CLI did not work on IPsec tunnels when using the ipsecstats command Tab completion is now possible to use in the ipsecstats command 14 The firewall did not accept certificates signed with RSA SHA256 15 Timezone setting could make the minimum date limit in scheduling to wrap and become a date into the future The minimum and maximum dates in scheduling have been modified to be between the years 2000 and 2030 which will not trigger the incorrect behavior 16 The SMTP ALG incorrectly blocked emails sent using the CHUNKING BDAT extension The ALG has been modified to remove the CHUNKING capability from the server s EHLO response This allows the emails to pass through the ALG 17 It was not possible to connect to the firewall using SSH if lots of public keys were registered in the SSH client 18 The firewall could unexpectedly restart when disabling automatic updates of anti virus and IDP updates 19 IPsec tunnels with a DNS name as remote endpoint would cease to function after a remote endpoint IP address change 20 Blacklist could potentially write to media up to five times each minute The SW Ww D Link NetDefend Firewall Firmware Release Notes Nl 3e delay between possible writes has been increased to two hours 21 It was not possible to configure maximum authentication retries

DES-3028/52 Series Firmware Release Notes - D-Link

Contents

Download Pdf Manuals

Related Search

Related Contents