User Manual - Protection Depot
Contents
1. DVD E Cabling Transmitter AV In Audio Video Ts 12V Input IR extender 3 x RCA Audio Video cables h Receiver P AV n DC 12V i IR emote Controller option DVR TV Monitor ai 3 x RCA Audio Video cables iG Camera DVR VCR DVD Set Top Box2. J Specifications Transmitter Operating Frequency Band 2 403GHz 2 478GHz Maximum Transmit Power 100mW Modulation 16QAM QPSK BPSK Video Input Level 1V p p 75 ohm Audio Input Level 1V p p 600 ohm STEREO Antenna Omni directional IR remote IR output 940nm with ON OFF keying Power consumption 1 9W Power supply 12V 1A Dimension 76mm 73mm 24mm Weight 82g Receiver Operating Frequency Band 2 403GHz 2 478GHz Receiver Sensitivity 85dBm min Video Output Level 1 0 2V p p 75 ohm Audio Output Level 1 0 2V p p 600 ohm STEREO Antenna Omni directional IR remote IR Input 940nm with ON OFF keying Power consumption 1 9W Power supply 12V 1A Dimension 76mm 73mm 24mm Weight 82g System Transmission channels 26 channels auto selection Video bit rate up to 12Mbps Random ID code up to 4 million sets Video resolution 720 x 480 30 fps NTSC or 768 x 576 25 fps PAL Operational range up to 800 meters line of sight and open site Remote control Optional range up to 500 meters line of sight and open site All specification subject to change without notice 214s 2 4GHz Digital Transmission system Manual with IR extender option V1 0 Important Safety Precautions To prevent fire or shock hazard do not expose this device to rain or moisture Does not use near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool m lo avoid electrical shock do not open this d
3. Monitor RX shows Wireless Camera CCD bad or no video input from TX wired i F camera DVD power off or stolen cable disconnected or No Video Signal damaged please check and make it right Wireless camera or TX power off wireless camera or TX vs RX distance is too long so that transmission signal is weak please check and make it right Monitor RX shows No Signal Check all cable connections Make sure power plugs are pushed all the way in Check power switches on the remote TV or DVR and No picture or sound Video source Camera Camcorder etc Check if the POWER LED of the transmitter digital wireless camera and receiver is lighting or not Their LINK LED should be lit If Their LINK LED should not be lit you must re pair their codes following the D instruction of the manual Adjust receiver and transmitter digital wireless camera antenna orientation Interference picture or audio Try to place transmitter digital wireless camera and receiver in a more close in location If using a microwave oven turn it off Remove microwave oven or wireless router from the path between transmitter digital w eless camera and receiver G Pairing the transmitter and receiver What is inside the Box When you get the transmitter digital wireless cameras or receiver you must pair Please check the following items inside the box for 2 4Ghz Digital Wireless them before use it following the
4. evice m_This device should be operated to use only the power supply included with it or provided as an accessory m Do not overload wall outlets and extension cords as this can result in the risk of fire or electrical shock m Do not attempt to service this device yourself Refer servicing to qualified personnel only m Reorient or relocate the receiving antenna m Increase the separation between the equipment and receiver m Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help E Note This equipment has been tested and found to comply with Part 15 of the FCC Rules or R amp TTE CE directive These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy if not installed and used in accordance with the instruction it may cause harmful interference to radio communications However there is no guarantee that interference will notoccur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Notice The change or modifications not expressly approved by the party responsible for co
5. f the receiver within 5 meter Following is the example for DVD Player installation 1 Transmitter TX uses orange color jack IR extender cable and Receiver RX uses black color iack gt 2 Install IR Cable 2 1 Transmitter s IR to the IR of DVD Player C Product Layout Front View Anten n a lt a Pairing buttons Power LED lt Power LED Pairing buttons gt Antenna L DC Jack for power adaptor AV Jack for Input TX IR Extender socket for RX IR Extender socket for TX DC Jack for power adaptor AV Jack for Output RX Back View Power On Off Antenna Connector Power On Off Antenna Connector For digital wireless camera Front view Back view Pairing buttoninside D Setting Up 2 4GHz wireless A V Link To enjoy wireless video and audio just connect the transmitter to whatever audio video source you want to enjoy from another location and connect the receiver to the TV monitor or powered speakers in that other location ROOM wireless camera SAT Receiver Video Audio Transmitter DVR Camera Stereo Remote Controller Optional A V link system is suggested to connect to following A V equipment use Video sources Audio sources m VCR Compact Disk player or Changer m Cable set top box with A Voutput m Stereo Receiver m Satellite Receiver m Cassette Deck m Laser Disc Player Camcorder or CCD Camera m DVR
6. instructions as below camera or Digital AV sender with IR extender option and contact your dealer if anything is missing 1 Power on the transmitter and receiver by inserting the power adaptor jack 1 Products body 2 Press the pair button of transmitter or receiver and not release until the power LED begin to flash then release the pairbutton 3 They will enter into the pairing state and automatically link to each other by ID code after step 2 finished 4 Please don t turn off their power switch during the paring status 5 When pairing successfully the power LED for both will be lit directly not flash or gt Pairing Button 2 Accessory for receiver andtransmitter 2 1 Refer to the following photo from left to right 2 2 Antennas x 2 for Transmitter and Receiver 2 3 AV cables x 2 3RCA plug to 3RCA plug 2 4 Power Adaptor x 2 100V 240V AC DC 12V 1A inJack 2 5 Optional IR extender x 2 for Transmitter orange color and Receiver black color Please note Pressing the pairing buttons for transmitter and receiver is not necessary at the same time and they are not necessarily put near or side by side in pairing status around within 3 meters far is OK Under the transmission you can see the strength signal on the monitor RX as below and will disappear after 5 seconds press RX pairing button will make it shown again 3 Accessory for digital wireless camera 3 1 Refer to the fo
7. llowing photo from left to right 3 2 Antennas x 1 3 3 Power Adaptor x 1 100V 240V AC DC 12V 1A inJack 3 4 Bracket with screws x3 4 This user manual B Introduction Thank you for purchasing this 2 4GHz Digital transmission system This system is a digital wireless audio video sender or camera that uses 2 4GHz Frequency Hopping technology and 16QAM QPSK BPSK modulation and random ID codes to protect personal privacy There are over billion hopping sequences to minimize interference anddeliver consistently an excellent video and audio quality up to 800 meters away This sender system also integrates an optional IR remote control extender to allow you to control the audio or video source from another room using your existing remote controller Using this 2 4GHz Digital Wireless system you can enjoy greaterconvenience and security in many ways General Application m Watch the movie you rent on any TV in house without moving your DVD laser disc player or running messy cables m Watch cable or satellite programs on any TV in house m Listen to stereo quality music from your receiver on any powered speakers inside or outside the house Safety amp Security Application Connect a camera as a wireless security system a Monitor your sleeping baby playing children the elderly or the disabled on TV using your existing camcorder See who is outside the door on TV through your camera or miniature CCD camera Monitor
8. mpliance could void the user s authority to operate the equipment IMPORTANT NOTE To comply with the FCC RF exposure compliance requirements no change to the antenna or the device is permitted Any change to the antenna or the device could result in the device exceeding the RF exposure requirement and void user s authority to operate the device H Use Notes 1 Be sure the transmitter and the receiver were connected to the equipment correctly e g Connect the transmitter to the camera and the receiver to the TV or DVR 2 When DC plug is pulled out from transmitter or receiver or wireless camera it needs to wait for a few seconds to insert it again 3 Adjust antenna to decrease interference vertical or horizontal 4 In most situations one pair has a better distance up to 800 meter open site When two pairs or more used at the same time can automatically jump to different channels but the distance between pairs preferably greater than 2 meters far 5 If there are some reasons cause the devise stop you can try to turn off the power then on again and make the devise re link re pairing 6 It is suggested to have 10 pairs mostly operated in same location but the pairing can not be at the same time 7 When use IR extender option itis normal when response slow in the receiver side RX by remote control please don t click the remote control keys too quick Troubleshooting Problems Possible Solution
9. s and records the meeting from anotherroom m Optional Extend the DVR control wirelessly connect the main out CVBS tothe transmitter and receiver to the TV monitor the guard people can look at the DVR screen in the TV monitor far from DVR and control the DVR by its remote control far way m And many more uses 2 2 Take off the sticker of IR terminal and cover on DVD IR hole Caution only the 1 3 top of terminal is available so must let the 1 3 top accurately to cover IR hole of DVD 2 3 Stick the terminal of receiver IR to anywhere of Monitor oT a Mar WE TIE Le ws on this side F Using the Remote Control Feature Optional This sender system not only allows you to send crisp audio video from one area to another it also gives you the ability to control the source using your existing remote control device It converts the infrared IR signal emitted by your remote control to aradio frequency RF signal in the receiver and sends it back to the transmitter where the RF signal is converted back to the original IR signal and control the audio video source such as DVD DVR VCR etc In order to obtain optimum performance of the remote control extender please operate as follow The first you need to plug the IR extender provided in the IR extender port of the transmitter and put the IR eye close to IR receiving window of A V source and then aim the existing remote control at the IR window o
Download Pdf Manuals
Related Search