EUKT01-RGB30 User Manual
Contents
1. RGB30 e Our commercial grade RGB LED controller has 31 changing modes and 256 grey levels changing in addition to manual controls for Brightness Speed Pause Mode and On Off Please read these guidelines before installing e Disconnect the AC DC power supply before making any cuts or connections e Do not connect power to the LED strip lights while they are coiled on the reel e Do not install or use this kit in wet or damp locations e Use LED strip lights only with a low voltage 12V DC power source and 5 24V DC RGB Controller e To protect the eyes do not stare directly into the LED lights when they are lit e Make sure to use the B R G indicators on the LED strip lights to maintain polarity and correct sequencing e For running wires inside walls use properly certified CL2 or better cabling e Do not install Class 2 low voltage wiring in the same runs with AC main power wiring If AC and DC wires cross keep them at 90 degree angles Peel Remove the 3M tape backing from the LED strip lights and stick in place Connect Simply use the wire interconnects and butt connectors to join the RGB strips Cut Locate the cut lines on the RGB strip light and cut strip to desired length Cutting Figure A Figure B Copper pad location Soldered copper pad location eg eli ER 7 F d g 2 gt d gg ag 3 Kei pi Cut the RGB strip light using scissors Make sure to cut strip in the center of th2. Listed Operation temp EUKT01 RGB30 Connector Use for AWG 22 LED strip thickness 0 3mm Current 5A AC DC Voltage 12 24V DC Operation temp 40 105 C Voltage Resistance 1500V AC min Contact Resistor 30m max 1000m min Housing PA6 Contact Over Brass Tin Tooth Slice double Tin Size 12 88 x 15 48 X 3 3 mm Cord Male Female Grounded plugs Input cable wire 18 AWG black power cord 120VAC Red Green Blue Yellow Purple Cyan White 7 colors flashing MODE SELECTION 9 Flashing 2 White flashing 10 6 colors flashing Gradual flashing 11 6 colors flashing 2 RGB gradual flashing 12 RGB flashing RG gradual flashing 13 RGB flashing 2 RB gradual flashing 14 RG flashing GB gradual flashing 15 RB flashing Flickering 16 GB flashing RGB Flickering White flickering RG flickering RB flickering GB flickering R flickering G flickering B flickering w EUComtrols EUKT01 RGB30 Standard Product Warranty PRODUCT WARRANTY EuControls warrants that at the time of shipment the standard products manufactured by EuControls and sold hereunder will be free from defects in material and workmanship for a period of three years from the date of shipment Warranty Adjustment Buyer shall notify EuControls immediately if any defect within the warranty period should appear EuControls agrees to repair or furnish a replacement for
3. but not install any product which within three 3 years from the date of shipment by EuControls shall upon examination by EuControls prove defective within the above warranty period No product will be accepted for return or replacement without written authorization of EuControls Upon such authorization and in accordance with instructions by EuControls the product will be returned shipping charge prepaid by Buyer Replacements made under this warranty will be shipped prepaid by Seller Exclusions from Warranty This warranty does not extend to any products manufactured by EuControls which has been subjected to misuse neglect accident improper installation or use in violation of instructions furnished by EuControls This warranty does not extend to or apply to any unit which has been repaired or altered other than at EuControls factory or by persons not expressly approved by EuControls Components purchased or made by Buyer from any supplier other than EuControls shall bear only the warranty given by the manufacturer of that product and EuControls assumes no responsibility for the interface of its product with any other product and such responsibility shall remain with Buyer for interface functionality and intended use Notice The foregoing warranty is in lieu of and excludes all other expressed or implied warranties of merchantability or fitness for use or otherwise EuControls Corporation 19210 S Vermont Ave Ste 310 Gardena C
4. A 90248 United States Toll free sales hotline 1 888 535 9580 Tel 1 810 643 5700 Fax 1 310 643 5688
5. A EuComtrols EUKT01 RGB30 RGB LED STRIP LIGHTING KIT EUKTO1 RGB30 This kit comes complete with everything you will need to light up your project It includes a deluxe RGB LED controller a mated AC DC power supply 16 4 of LED strip light and six light strip connectors In some cases you may need to splice connecting wire to power the LED strips or make extended turns It is recommended you first read these guidelines completely to understand how the products work and how they can be configured to your desired lighting layout Please note All wiring must comply with local and national electrical codes for Class II lighting If you are unclear on how to install this product please contact a licensed electrician All 120V AC main connections should be made by a licensed electrician What s included in the KIT Part Number Description EUPS06012 5 5 XR3 30400 RF EUACRE 003 euaconense Wired Interconnect with End EUAECON R10 to End connectors Butt Connectors Owner s Manual If any parts are missing please call 1 888 535 9580 e The AC DC power supply is UL listed and ready to use in a standard 120V AC outlet Any alterations or wiring modifications i e hardwiring to the 120V AC input power must be completed by a licensed electrician Please check your local codes prior to beginning any project All 12V DC output circuits meet Class II lighting requirements and are safe for DIY installation A EUComtrols EUKT01
6. curves or irregular Spaces since this might damage the LED s ts EuCom trols EUKT01 RGB30 OPERATIONAL MANUAL Power ON OFF Select Desired Mode Select Desired Select Desired Brightness Speed By pressing Up or Up for fast Down arrows Down for slow Power ON OFF Select Desired Mode Select Desired Brightness Press for high or for low Select Desired Speed Press for fast or for slow Battery at the back w EUConmtrols Power Supply Output Power 60W Output Voltage 12V Output Current 0 5A Input Voltage AC 100 240V 50 60Hz Range Voltage AC 90 264V 47 63Hz Over voltage Protection 120 min Over current Protection 120 min Load Regulation 5 Ripple and Noise 100mV Operation Temp 0 40 C Storage Temp 20 85 C Operation Humidity 5 96 Size SPECIFICATIONS RGB Controller Input Voltage DC 12 24V Remote Control RF remote control LED Tape 5050 SMD Distance up to 30 meters 30 LED meter Output Power 12V 12V DC maximum 12V 144W 24V 288W Speed and brightness adjustments Battery Alkaline 27A 12V Standby Power 0 5W 20 50 C 3 channel RGB Control Non waterproof View Angle 31 control mode 120 degrees functions Storage Temp 8 brightness level 30 C 80 C adjustments Power per 8 speed level meter 7 2watt adjustments Color RGB IP20 L 119 x W 52 x H 31 7 mm Safety UL
7. e copper pad locations as shown in the Figure A If you cut at a soldered location refer to Figure B You may need to remove the solder from the RGB strip light connection joint in order for the butt connectors to work properly A EUComtrols EUKT01 RGB30 Connecting g Carefully slide the LED tape into the connector so that copper pads on the RGB strip are positioned underneath the connector contacts Insert the RGB strip into the channel under contact tabs Figure 2 Snap the lid down to close the connector Perform a test to be sure that the connection is correct and that the LED s light before proceeding with the Figure 3 final installation Important Make sure to use the 12V B R G indicators printed on the LED tape light to ensure correct polarity and color sequencing 12V 12V i es SS Ses CC R es G B R G B R G If necessary the LED wires can be extended using 4 conductor 22 18 AWG wire But the shorter the length of wire added or the larger the wire gauge the less chance for voltage drop which would allow for higher LED brightness Please consult your electrician if you are unclear about your connections Planning EUKTO1 RGB30 Kit is designed for indirect lighting applications The light from the LED RGB strip should not be directly visable Every design is unique and the lighting effects depend on your personal preference The installation location surfaces wall colors moun
8. ting angle and objects can all affect the lighting appearance Before installing this LED lighting kit please consider the following Location of the power supply and the RGB Controller LED Lighting ON and OFF plan The layout configuration you will be using Wire connections to your LED strips w EUuUConmtrols EUKT01 RGB30 Typical Configuration Options Straight LED Connection RGR LED Strips Controller HUH Tene TEUENT Array LED Connection LED Strips RGB Controller f KO OE Loop Back LED Connection Z j ee H LED Strips RGB Controller Center Feed LED Connection f i LED Strips RGB Controller w EUConmtrols EUKT01 RGB30 INSTALLATION INSTRUCTIONS AC outlet 120V RGB Remote Control Power Supply Input Voltage 100 240VAC Output Voltage 12V DC a n RGB Controller LED Strips After you had determined the mounting position you are going to use e Make sure to clean the surface area The area should be free from oil or waxes and should be smooth and dry to ensure proper adhesion of the 3M tape on the back side of the RGB strip light e Gently remove the 3M backing and press the RGB strip light between the LED s to securely contact the surface of the mounting surface Never press on the individual LED s since this could damage their solder connections to the strip e Avoid sharply bending the LED strip solder joints in
Download Pdf Manuals
Related Search