Club Color Spot 250 MKII
Contents
1. 2 Insert a flat head screwdriver into a slot in the fuse cover Gently pry up the fuse cover The fuse will come out 3 Remove the used fuse If brown or unclear if is burned out 4 Insert the replacement fuse into the holder where the old fuse was Reinsert the fuse cover Be sure to use a fuse of the same type and specification See the product specification label for details Troubleshooting No Light No Movement All Products This troubleshooting guide is meant to help solve simple problems If a problem occurs carry out the steps below in sequence until a solution is found Once the unit operates properly do not carry out following steps lf the light effect does not operate properly refer servicing to a technician Response Suspect three potential problem areas the power supply the lamp the fuse 1 Power supply Check that the unit is plugged into an appropriate power supply 2 The lamp Replace the old lamp with a new one with the same specifications See page 7 for replacing lamps 3 The fuse Replace the fuse See page 15 for replacing the fuse No Response to DMX Response Suspect the DMX cable or connectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX cable Unplug the unit change the DMX cable then reconnect to electrical power Try your DMX control again 2 Determine whether the controller or light effect is at fault Does the controller operate properly with other D2. Club Color Spot 250 MKII ORDERCODE 40136 Congratulations You have bought a great innovative product from Showtec The Showtec Club Color Spot 250 MKII brings excitement to any venue Whether you want simple plug amp play action or a sophisticated DMX show this product provides the effect you need You can rely on Showtec for more excellent lighting products We design and manufacture professional light equipment for the entertainment industry New products are being launched regularly We work hard to keep you our customer satisfied For more information want showtec into You can get some of the best quality best priced products on the market from Showtec So next time turn to Showtec for more great lighting equipment Always get the best with Showtec Thank you Showtec Showtec Club Color Spot 250 MKII Product Guide Warning an nan a Safety instructions sc nt E ag E atten a 80 id du EEE TAIE i i a pet Sie let Dee Aa OI scene im ocean elin eta t ar aa ni RICE RTS acea en aia Description ai bin lu aa anl al da nana esta naa Naa a dn sata Features and Oven E se a an NN NA ait a ao oe a aa NA a aa AE 10 lt 5 6 se ic ei pica al Installation i de T Installing ihe Lamp Lamp Adjustment Set Up and ODS OW sn ea ia dc em der do iii le a e cad n i ta BIRT A OM On oo nat atita al in a d pina NAN AA E aaa at NN tati PA er a e MUn ON DO PR PR Miz aie bon ale ta a ia i arrival
3. DMX PIOIGEOI Na aa SA DA Naa NAN NN AA NA Conto PORNS lees a NA ara la D iai Bt al aa a d au oala a aa a ta ia a dl al Control Mode DMX addressing Functions control panel Stand alone mode Master Slave pp Le Lo a deren ete entot AA RI DA AS PRE nan Ng no A t ded a Colorwheel ccc cece ccc ccceccceccccccuucccccceeuccceeteuceceeteuceeceeteceececenucecs Maintenance Changing the Lamp Replacing the Fuse Troubleshooting No Light No Movement All Products No Response to DMX eu Product Specifications D et PA TA ee a TAN AN ee WARNING CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP SAFETY INSTRUCTIONS Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires Before your initial start up please make sure that there is no damage caused by transportation Should there be any consult your dealer and do not use the device To maintain perfect condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual P
4. than the one described in this manual the product may suffer damages and the warranty becomes void Any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc You endanger your own safety and the safety of others Rigging Please follow the European and national guidelines concerning rigging frussing and all other safety issues Do not attempt the installation yourself Always let the installation be carried out by an aufhorized dealer Procedure e If the projector is lowered from the ceiling or high joists professional trussing systems have to be used e Use aclamp to mount the projector with the mounting bracket to the trussing system e The projector must never be fixed swinging freely in the room e The installation must always be secured with a safety attachment e g an appropriate safety net or safety cable e When rigging derigging or servicing the projector always make sure that the area below the installation place is blocked and staying in the area is forbidden Improper installation can cause serious damage fo people and property Connection with the mains Connect the device to the mains with the power plug Always pay attention that the right color cable is connected to the right place International EU Cable UK Cable US Cable Pno BROWN RED YELLOW COPPER FASE BLUE BLACK SILVER YELLOW GREEN GREEN GREEN EARTH Make sure that the de
5. the small metal housing 3 Read lamp instructions Do not touch the lamp bulb glass See Figure 3 Oil on hands shortens the lamp life If you touch the bulb glass wipe off the glass with a clean lint free towel and rubbing alcohol 4 Insert the lamp pins into the small holes in the lamp socket 5 Put the lamp cover back and fasten the screws snugly Fig 3 Lamp Adjustment You can adjust the lamp s position by turning the screws A B C The lamp position is set in the factory As the lamps which can be used differ from manufacturer to manufacturer it can be necessary to readjust the position The lamp must be readjusted e g if the light does not seem to be evenly distributed within the ray of light Ignite the lamp and focus the ray of light on an even surface wall As the optimal distance between the lamp and the lens was already set during the installation with screw A only the Hot Spot the brightest part of the ray of light must be centered Turn in addition screw B and C If the Hot Spot appears too bright you can weaken its intensity by moving the lamp closer to the reflector Turn in addition screw A until the light is evenly distributed If the light at the outside edge of the ray of light appears brighter as in the center the lamp is too close to the reflector In this case move the lamp away from the reflector until the light is evenly distributed and the ray of light appears bright enough R
6. them disturbs data transmission on the directly together link Have the defective fixture serviced by a qualified technician Install a phase reversing cable erratically or not at all fo the controller 3 pin XLR Out on the fixtures does between the fixtures or swap pin 2 not match pins 2 and 3 reversed and 3 in the fixture that behaves erratically Shutter closes The color wheel gobo wheel ora Contact a technician for servicing if suddenly gobo has lost its index position and the problem persists the fixture is resetting the effect The power supply settings do not Disconnect fixture Check settings No light match local AC voltage and and correct if necessary frequency Allow fixture to cool Lamp cuts out Fixture is too hot Clean fan intermittently Make sure air vents at control panel and front lens are not blocked Turn up the air conditioning The power supply settings do not Disconnect fixture Check settings match local AC voltage and and correct if necessary frequency 16 Product Specification Model Showtec Club Color Spot 250 MKII Voltage 240V 50Hz CE Fuse 10A 250V Dimensions 425x290x385mm LxWxH Weight 11 76 kg Operation and Programming Signal pin OUT pin 1 earth pin 2 pin 3 Set Up and Addressing LED control panel DMX Channels 2 Signal input 3 pin XLR male Signal output 3 pin XLR female Lamp Allowed lamp models Showtec NSD 250
7. 2 2000 hr ordercode 82603 Philips MSD 250 3000 hr 6700K ordercode 80920P Osram HSD 250 2000 hr 6000K ordercode 809260 Osram HSD 250 78 1000 hr 7800K ordercode 809330 Osram HSD 250 80 1000 hr 8000K ordercode 80935 Control Automatic and DMX remote ON OFF Electro mechanical effects Colour wheel 7 colours open Colour wheel with variable rotation soeed All lenses are anti reflection coated High luminous efficiency parabolic system Strobe effect with variable speed 1 flash 10 flashes sec DMX control via standard DMX controller Max ambient temperature fa 40 C Max housing temperature s 80 C Minimum distance Minimum distance from flammable surfaces 0 5m Minimum distance to lighted object 1 3m Versions for other lamps may be produced Please check the specification label on your product Design and product specifications are subject to change without prior notice CE Website www Highlite nl Email service highlite nl O HIGALITE INTERNATIONAL 17 2007 Showtec
8. Avoid brute force when installing or operating the device e Only use device indoor avoid contact with water or other liquids 2 e Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened Only operate the device after having familiarized with its functions Avoid flames and do not put close to flammable liquids or gases Always replace the lamp when it is damaged or deformed due to the heat Always keep case closed while operating Always allow free air soace of at least 50 cm around the unit for ventilation Always disconnect power from the mains when device is not used before cleaning or when replacing lamp Only handle the power cord by the plug Never pull out the plug by tugging the power cord e Make sure that the device is not exposed to extreme heat moisture or dust e Make sure that the available voltage is not higher than stated on the rear panel e Make sure that the power cord Is never crimped or damaged Check the device and the power cord from time to time e If the lens is obviously damaged if has to be replaced So that its functions are not impaired due to cracks or deep scratches e If device is dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating e If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch if on immediately The
9. MX products 8 If not fake the controller in for repair If so take the DMX cable and the light effect to a qualified technician See next page for more problem solving 15 Probable cause s No power fo the fixture Check that power is switched on One or more And cables are plugged in completely dead Primary fuse blown Replace fuse Fixtures reset The controller is not connected Connect controller 3 pin XLR Out of the controller Install a phase reversing cable does not match XLR Out of the first between the controller and the first fixture on the link i e signal is fixture on the link reversed correctly but all respond erratically or not at all to the controller Check data quality If much lower than 100 percent the problem may be a bad data link connection poor Poor data quality quality or broken cables missing termination plug or a defective fixture disturbing the link Insoect connections and cables Bad data link connection Correct poor connections Repair or replace damaged cables Data link not ferminated with 120 Insert termination plug in output jack Fixtures reset eae Ohm termination plug of the last fixture on the link oe t addressing of the fixt Check add tt some respond ncorrect addressing of the fixtures eck address setting _ Bypass one fixture at a time until normal operation is regained unplug One of the fixtures is defective and both connectors and connect
10. a test program all slaves will execute these acts too You can t play or edit any program on a slave if the master is switched on and connected to the master slave chain Note Disconnect the fixtures from the DMX controller before master slave operating otherwise data collisions can occur and the fixtures will not work properly It s necessary to insert the XLR termination plug with 120 Ohm into the input of the master fixture and into the output of the last slave fixture in the data link in order to ensure proper transmission on the data link From the master s control panel it is possible to control any slave in a master slave chain Channels settings 1 Colour wheel 1 2 Shutter 13 Colorwheel Fig 6 Maintenance The operator has to make sure that safety relating and machine technical installations are to be inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are to be inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the device or parts of the device have to be tightly connected and must not be corroded 2 There may not be any deformations on housings fixations and installation spots 3 Mechanically moving parts like axles eyes and others may not show any traces of wearing 4 The electric power suppl
11. arising condensation water might damage your device Leave the device switched off until if has reached room temperature e If your Showtec device fails to work properly discontinue use immediately Pack the unit securely oreferably in the original packing material and return if to your Showtec dealer for service e For adult use only Movinghead must be installed out of the reach of children Never leave the unit running unattended e Forreplacement use lamps and fuses of same type and rating only e Allow time to cool down before replacing lamp e This device falls under protection class Therefore if is essential fo connect the yellow green conductor to earth e During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective e Repairs servicing and electric connection must be carried out by a qualified technician e WARRANTY Till one year after date of purchase Avoid looking directly into the light source meant especially for epileptics CAUTION EYEDAMAGES OPERATING DETERMINATIONS This device is not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects The minimum distance between light output and the illuminated surface must be more than 1 3 meter The maximum ambient temperature ta must never be exceeded If this device is operated in any other way
12. d fourth units 4 Supply electric power Plug electric mains power cords into each unit s IEC socket then plug the other end of the mains power cord into proper electric power supply sockets starting with the first unit Do not supply power before the whole system is set up and connected properly Multiple Club Spots Set Up DMX Set up Master Slave Set up Fig 5 Note Link all cables before connecting electric power DMX Protocol Channel 1 Colours Linear color change following the movement of the slider In this way you can stop the color wheel in any position also between two colors creating double colored beams Between 126 255 the color wheel rotates continuously the so called Rainbow effect 687l ROD oo Channel 2 Shutter Shutter Close 6 116 Gradual Open 117 139 Shutter Open 140 199 Strobe effect with increasing speed 200 249 Random strobe effect with increasing soeed 290 255 Shutter Open 10 The Club Color Spot 250 MKII can be operated with a controller in control mode or without the controller in stand alone mode Control Panel When the indicator light is on means the Club Spot is working ENTER Fig 5 Control Mode The fixtures are individually addressed UL 5 on a data link and connected to the controller The fixtures respond to the DMX signal from the controller When you select the DMX address and save if the controller will disolay the saved DMX address the nex
13. emove the screws X Y and Z for re lamping 6 03 Y WARNING Disconnect the fixture from AC power before refamping Lamp is hot Risk of fire Protect hands ang eyes Wait at least 15min before opening the 90 and removing lamp from the fixture Backside Lamp Board 3 adjustment screws A B C Fig 4 Set Up and Operation Follow the directions below as they pertain to your preferred operation mode Before plugging the unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa One Club Spot 1 Fasten the moving head onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Club Spot Leave at least meter on all sides for air circulation 2 Plug one end of the electric mains power cord into the IEC socket on the unit Then plug the other end of the cord into a proper electric power supply socket ipsa ae Club Spots Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Club Spot Leave at least 1 meter on all sides for air circulation 2 Use a 3 p XLR cable to connect the Club Spots and other devices The pins Earth 2 Signal 3 Signal 3 Link the units as shown in figure 5 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third an
14. ess the MODE ESC button until the display shows ESEJ Press the ENTER button will system reset System reset MODE 7 Press the MODE ESC button until the display shows EE Press the ENTER button will go back to the default mode Load default 12 Remotely controllable functions Colour wheel The Club Spot contains a colour wheel with 9 colours and white The colour wheel can be positioned between two adjacent colours in any position It is also possible to rotate the colour wheel continuously at different soeeds Rainbow effect in both directions Shutter This unit may be used for strobe effect 1 10 flashes per second Stand alone Mode The fixtures on a data link are not connected to the controller but can execute pre set programs which can be different for every fixture To set the program to be played see the page 10 Stand alone operation can be applied to a single fixture the fixture may be set to the master slave mode or controller mode or to multiple fixture operating synchronously For synchronous operation of multiple fixtures the fixtures must all be connected on a data link and one of them is set as a master master mode and the rest as slaves slave mode The DMX address of all the Ani slaves are assigned to Lit and on that particular slave address only one fixture can be connected To the i ar mm fixture as the master or slave see Addressing menu uu If the master fixture resets or runs
15. lease consider that damages caused by manual modifications to the device are not subject to warranty This device contains no user serviceable parts Refer servicing to qualified technicians only IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device e Never let the power cord come into contact with other cables Handle the power cord and alll connections with the mains with particular caution e Never remove warning or informative labels from the unit e Never use anything to cover the ground contact e Neverrun the device without lamp e Never ignite the lamp if the objective lens or any housing cover is open as discharge lamps may expose and emit a high ultraviolet radiation which may cause burns e Never lift the fixture by holding It at the projector head as the mechanics may be damaged Always hold the fixture at the transport handles e Never look directly into the light source e Never leave any cables lying around e Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened e Do not insert objects into air vents e Do not connect this device to a dimmerpack e Do not switch the device on and off in short intervals as this would reduce the lamp s life e Do not touch the device s housing bare handed during its operation housing becomes very hot e Do not shake the device
16. n the last fixture in order to ensure proper transmission on the DMX data link 11 MODE 1 Em as default mode Receive DMX512 signal set the desired address via the UP DOWN d C O 5 a DMX mode select channel 1 channel 512 MODE 2 as Auto program of master unit select 8 different auto program from to via up down buttons Press the ENTER button to confirm your selection Press MODE ESC cancel the selection and enter to next mode Master Speed Master Speed 2 Master Speed 3 Master Speed 4 Master Speed 5 Moster Speed 6 Master Speed Master Speed 8 MODE 3 Slave mode press ENTER button to follow the master unit Press MODEESC cancel selection and enter to next mode Slave mode slave MODE 4 Press the MODE ESC button until the display shows BEMS BEBE and set desired function via UP DOWN buttons EZ as LED positive mode and rd 15 as LED Negative mode Press the ENTER button confirm the function and the display will shows DMX or MASTER SLAVE mode that you selected before LED mode Positive LED mode Negative LAF and set the desired function via UP DOWN buttons i Aon as lamp on mode and as lamp off mode Press the ENTER button confirm the function and the display will shows DMX or MASTER SLAVE mode that you selected before Lamp on Lamp off MODE 6 Pr
17. t time DMX Addressing The control panel on the front side of the base allows you to assign the DMX fixture address which is the first channel from which the Club Spot will resoond to the controller Please note when you use the controller the unit has 2 channels When using multiple Club Spots make sure you set the DMX addresses right Therefore the DMX address of the first Club Spot should be 1 001 the DMX address of the second Club Spot should be 1 2 3 003 the DMX address of the third Club Spot should be 3 2 5 005 etc Please be sure that you don t have any overlapping channels in order to control each Club Spot correctly If two or more Club Spots are addressed similarly they will work similarly For address settings please refer to the instructions under Addressing menu ALL Controlling After having addressed all Club Spot fixtures you may now start operating these via your lighting controller Note After switching on the Club Spot will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the LED on the control panel will not flash The problem may be The XLR cable from the controller is not connected with the input of the Club Spot The controller is switched off or defective the cable or connector is detective or the signal wires are swapped in the inout connector Note It s necessary to insert a XLR termination plug with 120 Ohm i
18. vice is always connected properly to the earth Description of the device Features The Showtec Club Color Spot 250 MKII is a moving head with high output and great effects e Colour wheel 7 dichroic colours open e DMX control via standard DMX controller e 2 DMx control channels required e Strobe effect with adjustable speed 1 10 flashes sec e Sound controlled via built in microphone e Auto mode master slave function e Lamp MSD 250 80920P 809200 809330 82603 80935 e Fuse TIOA 250V Overview Fig 1 1 Lens Backside 2 DMX signal connector IN 3 IEC Connector Fuse 10A 250V 4 DMX signal connector OUT Installation Installing the Lamp The Showtec Club Color Spot 250 MKII uses the MSD 250 80920P 809200 809330 82603 80935 reflectorbulb as manufactured by all popular manufacturers Use only the appropriate lamp for your unit Note that product versions that use other lamps may be offered in the future Check your product specification label for information Always disconnect from electric mains power supply before changing lamps The lamp has to be replaced when if is damaged or deformed due to the heat Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty Procedure 1 Loosen the 3 screws on the back of the housing 2 Gently remove
19. y cables must not show any damages or material fatigue The Showtec Club Color Spot 250 MKII requires almost no maintenance However you should keep the unit clean Otherwise the fixture s light output will be significantly reduced Disconnect the mains power supply and then wipe the cover with a damp cloth Do not immerse in liquid Wipe lens clean with glass cleaner and a soft cloth Do not use alcohol or solvents The front PC lens will require weekly cleaning as smoke fluid tends to build up residues reducing the light output very quickly The cooling fans colour filters the gobo wheel the gobos and the internal lenses should be cleaned monthly with a soft brush Please clean internal components once a year with a light brush and vacuum cleaner Keep connections clean Disconnect electric power and then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power 14 Changing the Lamp 1 Disconnect mains power supply Loosen the 3 screws on the back of the housing 2 Gently remove the small metal housing 3 Follow directions for installing a new lamp page 7 Replacing a Fuse Power surges short circuit or inappropriate electrical power supply may cause a fuse to burn out If the fuse burns out the product will not function whatsoever If this happens follow the directions below to do so 1 Unplug the unit from electric power source
Download Pdf Manuals
Related Search