PDR3000 User Guide - OSI International
Contents
1. for compatibility with other units for example make sure you only use the older version of PDT3P for programming IMPORTANT Always do a Download from Pager and save the config xxx ses file before carrying out any programming changes Firmware Upgrading 1 FTP First Time Programming 2 ES Embedded System Upgrade Important notice 2000 generation units up to version 5 1 only 3000 generation units version 6 onwards 1 FTP This is only to be done on instruction from WiPath Open winflash_p Select your comport Place a 2 54mm jumper over JP1 Click on the f button and select the rom file 2000 generation pdt_ftp_PEv2 6 rom 3000 generation pdt_ftp_PEV6 0 rom Click the Flash button Apply power to the unit wait to the bar at the bottom goes to 100 Remove power Remove the Jumper on JP1 2 ES Upgrade Open Latest version of PDT3P or specified version Select your template Click ES Upgrade Flash Pdt_Flash_PEv version type Apply power to the unit wait until the bar at the bottom goes to 100 Apply power to the unit a warning will be displayed click no and wait until the bar at the bottom goes to 100 Enter your settings or open a saved file and click upload to pager Note If the settings file ses is from a different firmware version it may not load and the settings will have to be reconfigured manually in PDT3P Available Software interfaces Logpag2. Operation is subject to the following conditions 1 This device many not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Copyright WiPath and PDT3000 are registered trademarks All rights reserved All other trademarks and registrations are the property of the respective owners Flex is a licensed trademark of Motorola Notes
3. e message logging software All application software is available for free 30 day trial from www wipath com Troubleshooting Unit not receiving Check whether you are in a paging coverage area Check correct capcodes are set Check the frequency is within the range of the receiver see Notes section in PDT3P Check that correct protocol template is loaded Flex pocsag Check that receiver settings are correct Inverted baud rate etc Check the unit is programmed to the correct receiver type All later units are RCM Unit is not beeping and are correctly set in the Serial options window and are correctly set in the Msg relay options window Can t download from unit Check serial cable is null modem Check power is available and connected If you have no response from the unit perform an ES Upgrade which may require a power cycle or contact your local service agent CONTACTS WiPath New Zealand WiPath Australia WiPath USA 3 2 Haultain Street Unit 44 8 Avenue of 4845 Dumbbarton Court Eden Tce Americas Newington Cumming Auckland 1024 Sydney NSW 2127 GA 30040 9606 New Zealand Australia USA 64 9 3021142 61 2 81978275 1 770 844 6218 info wipath co nz info wipath com au info wipath com www wipath co nz www wipath com au www wipath com WIPATH DISCLAIM ALL LIABLILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS DAMAGE OR VIOLATE THE LAW Compliance This device complies with part 15 of the FCC rules
4. le power supply and programming it from a PC using the PDT3P programming kit see below If the PDR3000 was preprogrammed for you by the dealer then PDTSP is not required The PDR3000 requires 12VDC 500mA for operation An optional plug pack power supply is available If using an alternative power supply the fused DC power cable supplied should be used Note that the RJ45 ports may also be used to supply 12VDC We recommend that any power supply be fused 2A Peripheral devices may be plugged into the various I O ports according to the information above If using with LogPage the PDR3000 will connect to the PC running LogPage using the same null modem serial cable used for programming Programming the PDR3000 To program the PDR3000 you will require a null modem RS232 cable DB9F DB9F and the PDT3P software These can be purchased as a kit All programming functionality is fully explained in detail in the PDT3P help file You should receive with PDT3P a template key which will activate the programming template for the PDR3000 you have purchased Flex or pocsag If you did not receive this key contact WiPath or your dealer Please ensure that you always use the same version of PDT3P as the version of firmware contained in your PDR3000 This can be read from the PDR3000 using PDT3P If the firmware version is older than the PDTSP version carry out an ES Upgrade see below If there is a specific reason to use an older version of firmware
5. sign control e Remote telemetry control Specifications Protocols Outputs Receiver Frequencies Channel Spacing Data rate Freq Deviation Rx Sensitivity Selectivity Image Rejection Spurious Rejection Frequency Stability Antenna Available in Pocsag and Flex 1 parallel port 2 serial ports I O 4 Relays 12 alarm inputs Opt Synthesized FM FSK 134 139 148 174 408 412 450 470 929 932 MHz 25 KHz 12 5kHz optional 512 2400 pocsag 1600 2 6400 4 Flex 4 5 KHz 5 uV at 1200 bps better than 60 dB better than 55 dB better than 55 dB 10 ppm at 10C 60C 50 Ohm BNC VHF amp UHF SMA 900MHz Power 10 32VDC 12VDC nominal Current Typical 30mA in standby 300mA max Physical 230 x 94x 56mm 9 x 3 5 x 2in excl bracket Operating Temp 10 70degC 40 70degC version available Relays Rated 1A 12VDC General On board real time clock with back up battery Up to 12 alarm inputs Pocsag data encoder Transmitter control output PTT and data PINOUTS BHC DB25 Parallel DBS Serial Power Antenna Printer Port Data Port optional O GEEZ afer ee oe ovals or maa sej momo Filyi Aly 1 Fly2z Aly2 Aly Alt Alt ME Com MC Com MO 44 Gnd po Flys Aly3 Rly Aly Aly4 Aly Alt Alt ME Com NO MC Com M l24 Gnd ne Installing the PDR3000 Installing the PDR3000 is generally a simple matter of attaching the antenna plugging it into a suitab
6. vil PENN ViPath W PDR3000 Paging Data Receiver User Manual www wipath com Januar y 2009 1 Introduction The PDR3000 Paging Data Receiver is a multi function paging data receiver off air decoder capable of receiving paged messages and processing them in a variety of ways It is able to print messages direct to a parallel or serial printer or output the message data via the two serial ports in a number of different formats and protocols The PDR3000 has four relay control outputs internally or may be interfaced with the RCM3000 Relay Control Module for multiple relay control Other options include an inbuilt pocsag paging encoder for repeater or rebroadcast applications and other specialised serial data inputs and outputs for control of devices such as LED signs synchronized clocks etc The PDR also has an inbuilt search and replace text facility for manipulating the incoming messages Features e Very large capcode capacity e Receivers available for most paging e Programmable data outputs bands VHF UHF 900MHz e Serial outputs e Battery backed real time clock e Parallel output e Pocsag and Flex versions available e Relay outputs e Pocsag encoder output e Individual capcode output e Transmitter control programmability Applications e Message logging e Machinery switching and control e Message forwarding e Coverage expansion e Message printing e Transmitter monitoring e Network monitoring e Alarm transmission e LED
Download Pdf Manuals
Related Search