Home

Instructions

1. Mode 6 Waveform a Max Voltage SOV single phase Mode 7 Waveform A B C 300uS a b 160uS Max Voltage 50V single phase Mode 8 Waveform A B C 300uS a b 160uS Aja B ohc Max Voltage SOV single phase Mode 9 Waveform Mode 10 Waveform C 300uS a b 160uS Max Voltage 50V single phase How to operate For feet BAND 1 In order to increase the conductivity we recommend that you dampen the soles of your feet 1 Place your bare feet onto ElectroVita do not wear socks 2 Press and hold down for 3 seconds the on off button the LCD screen will light up in blue The program will show 01 and both band shows 00 which means the device is in standby mode See Figure 3 3 Select the program you wish to use there are 10 different programs which are indicated on the LCD display Select the program by pressing P and P See Figure 4 Gently increase intensity setting by holding down the button Ax Or decrease intensity setting by holding down the button W The intensity level is adjustable between O and 40 See Figure 7 In order to let the user feel the stimulation gradually increase the intensity to a comfortable level by holding down the intensity button Those who suffer with poor circulation may not feel anything until reaching a higher level of intensity There are 40 output levels When yo
2. Rated maximum Separation distance according to frequency of transmitter output power m of transmitter 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz Ww d 12 P d 12 P d 23P 0 01 0 12 0 12 023 01 0 38 0 38 0 73 1 12 12 23 10 38 38 73 100 12 12 23 For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer NOTE 1 At 80MHz and 800MFz the separation distance for the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people 21 22 JML Distributed by JML Unit 1 Eastside Port of Tyne i A M C 0473 South Shields NE33 SSP info JMLgroup co uk Product code Freephone 0800 781 7831 Web www JMLdirect com V0393 Registered address JML House NW5 3EG
3. Width Diagram be ow during 1kQ load connected with the sole electrode part dotted line area means single phase continuous working for 1 second Ashe single phase single phase Adhd LLM LULA single phase single phase single phase VV single phase Mode 1 Waveform A B C 300uS a b 160uS Max Voltage 50V Mode 2 Waveform A B C 300uS 160uS Max Voltage 50V Mode 3 Waveform Max Voltage 50V Mode 4 AB H C Waveform A B C 300uS a b 160uS Max Voltage 50V Mode 5 od Waveform A B C 300uS 605 Max Voltage SOV Mode 6 A B H C Waveform Max Voltage 50V Mode 7 Waveform A B C 300uS a b 160uS Max Voltage 50V Mode 8 Waveform A B C 300uS a b 160uS Max Voltage SOV Mode 9 Waveform Mode 10 Waveform Max Voltage SOV 11 Ahe single phase single phase Body Massager EMS Waveform and Pulse Width Diagram below during 1kQ load connected with the sole electrode part Mode 1 Waveform A B C 300uS a b 160uS Max Voltage 50V single phase Mode 2 Waveform A B C 300uS a b 160uS Max Voltage 50V single phase Mode 3 Waveform Mode 4 Waveform A B C 300uS a b 160uS Max Voltage 50V single phase Mode 5 Waveform A B C 300uS a b 160uS Max Voltage 50V single phase
4. components may result in increased EMISSIONS or decreased IMMUNITY of the ElectroFlex 4 Warning the ElectroVita should not be used adjacent to or stacked with other equipment Guidance and manufacturer s declaration electromagnetic emissions The ElectroVita is intended for use in the electromagnetic environment specified below The customer or the user of the ElectroFlex should assure that it is used in such an environment Emissions Compliance Electromagnetic Environment Guidance RF emissions CISPR 11 Group 1 The ElectroVita uses RF energy only for its intemal function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF emissions CISPR 11 Class B The ElectroVita is suitable for use in all establishments including domestic Harmonic emissions IEC 61000 3 2 CLASSA establishments and those directly connected to the public low voltage power supply network Voltage fluctuations flicker emissions IEC 61000 3 3 Complies that supplies buildings used for domestic purposes 18 Important Information 5 Guidance and Manufacturer s Declaration Electromagnetic Immunity The ElectroVita is intended for use in the electromagnetic environment specified below The customer or the user of the ElectroVita should assure that it is used in such an environment Immunity Test IEC 60601 Compliance Electromagnetic Environment Guidance T
5. electrol ta jc circulation enhancer Instructions electrol ta circulation enhancer Thank you for purchasing the ElectroVita Circulation Enhancer Helps reduce stresses and aches with the amazing ElectroVita Circulation Enhancer from JML Simply place your feet on the footpads set the intensity level and sit back Low frequency micro currents safely stimulate the reflex points in your feet waking up tired nerves muscles and capillaries Capillaries are the smallest of your bodies blood vessels and provide the exchange between cells and circulation So relax and re energise with the ElectroVita Circulation Enhancer Contents Quick start guide 02 Important Safety Information ______ 03 06 What is Electronic Nerve Stimulation 07 Machine Overview and Part Names __ 08 Functions and Programmes 09 Electroflex Output Wave Forms ___ 10 11 How to Operate 12 14 Cleaning 15 Troubleshooting and Maintenance __ 16 17 Important information 18 21 Auick Start Guide For detailed operation of your ElectroVita Circulation Enhancer Electrical Stimulator please refer to the comprehensive instructions within this manual To use the Circulation Enhancer immediately follow this 5 point quick start guide 1 Remove your ElectroVita Circulation Massager from the packaging Connect the DC adapter to a suitable mains outlet and plug the small DC socket into the device 2 Turn on the power the centr
6. e Do not clean with chemicals Store in a dry dust free location in a temperature between 10 C to 40 C and 30 to 90 relative humidity A Safety Precautions e Do not open the device or repair it yourself This will invalidate your warranty and may cause serious harm e If the device malfunctions disconnect it from the power source and contact your selling agent as soon as possible Use only the accessories supplied by the manufacturer Use the device only for its intended purpose Do not expose the device to extreme heat Do not overload the electrical outlet Do not stand on the machine Use it when sat down only Do not spill liquid on the device or its accessories The warranty is void if the product has been altered misused or abused We will not take any responsibility Regulatory Certification UK Europe Class lla medical device This symbol indicates that the unit meets the CE basic requirements set by the CE Directive 93 42 EEC concerning medical devices ElectroFlex complies with the WEEE Directive Disposal of the device in accordance with EU regulations applicable at the place of operation Dispose of at public collection mmm points in EU countries ISO 13485 Manufactured under the international quality management standard for medical devices 15 Troubleshooting and Maintenance SYMPTOM CAUSE ACTION Device will Batteries inserted in wrong direction Insert batteries in
7. correct direction or check the nottum on battery is not discharged The adaptor is not connected to the Checkthe connection of the adaptor jack is properly device correctly connected to the device and in the wall socket Power turns o Gel pads not attached Attach Gel pads correctly to the skin too soon correctly to the skin Power turns o If you are using the batteries operation Fit three new 1 5V alkaline batteries type C while using then the batteries are weak exhausted massager Treatment period of 25 minutes is over Restart treatment or tum off the massager and power turns off automatically If you are using the body massager Replace electrode cord the cable may be damaged It is difficult to Transparent film not peeled off Peel off film on the adhesive surface of gel pad attach gel pad Gel pad applied immediately Allow gel pad to dry to the skin after washing Adhesive surface of gel pad damaged Replace gel pad The gel pads get dirty and lose their Replace gel pad or clean the gel pad with a small drop adhesive stickiness of water rubbed onto the sticky side of the electrode pad Adhesive surface Use of gel pad during perspiring Chill the gel pad in adomestic fridge for 3 4 hours of gel pad is sticky Gel pad washed too long and or too frequently Gel pads stored under high temperature high humidity or direct sunshine It is difficult to feel stimulation The soles of your feet are too dry Your soles are not placed on the fo
8. sticky objects The life of the electrodes varies depending on skin conditions storage amount of use type of stimulation and stimulation site Usage may be extended by carefully cleaning the gel surface with a damp cloth Do not get the cables wet when cleaning Single patient use only e Do not apply to broken skin Should a skin rash occur discontinue use and contact your physician Do not use tissue cloth etc to scratch the electrode surface e Do not use anything abrasive to clean the electrode pads this will damage the pad surface e Do not frequently clean the pads and do not use detergent or hot water to clean the electrode gel pads e The adhesive will become less effective if the gel pad is contaiminated Wash the pads under slow running water for about 2 3 seconds Caution Do not use hot water Do not wipe the adhesive surface Let the adhesive surfaces of pads air dry Adhesive surface sides up during drying To sterilize the foot plate use a mild antiseptic solution Main Device e Turn off the power remove the adaptor and the electrode gel pad from the unit for storage in correct way Always keep the main device clean by using a soft cloth to clean the surface of the unit e To clean the foot plates use a soft damp cloth dry thoroughly after cleaning To clean the main unit use a soft damp cloth dry thoroughly after cleaning e Do not spill liquid on the device Do not immerse the device in water
9. 230V 50Hz 100mA Adaptor Output 4 5V DC 100mA 0 45VA Battery Life Approx 1 Month When used 25 minutes a day continuously Frequency Generation Approx 1Hz to 80Hz Power Consumption 0 45W Maximum Output Voltage U lt 50V during 1kQ load Maximum Output Current lt 10mA during 1kQ load Operating Temperature and Humidity 10 C to 40 C 30 to 90 RH Storage Temperature and Humidity 10 C to 60 C 10 to 95 RH Main Unit Dimensions 430 L x 430 W x 150 H mm Weight Approx 1900g Package Contents Ouantity Parts 1 HectroVita Circulation Massager Electrical Stimulator 1 AC DC Adaptor 1 Sole Massage Roller 2 Cable Wire for Electrode Gel Pads 4 Electrode Gel Pads 2 Plastic Gel Pad Protectors 1 Instruction Manual Accessories e Only use original accessories Do not substitute with non approved parts e Check the contents are correct 17 Important Information Electro Magnetic Compatibility EMC 1 ElectroVita needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the ACCOMPANYING DOCUMENTS 2 Portable and mobile RF communications equipment can affect ElectroVita 3 Warning that the use of accessories transducers and cables other than those specified with the exception of transducers and cables sold by the manufacturer of the ElectroFlex as replacement parts for internal
10. The icons and meanings are as follows Examples of Icon This icon means prohibited must not do Anything prohibited is marked clearly with this warning symbol This icon indicates something that is compulsory must be observed Compulsory actions are marked clearly with this warning symbol This product should not be used by persons with electronic medical implants e g heart pacemakers organ transplant or other electronic life support systems Disposal of this product and used batteries should be carried out in accordance with the national regulations for the disposal of electronic products Directive 2002 96 EC WEEE li Consult instructions for use m Date of manufacturer daa Manufacturer s name Batch Code f Authorised representative in the European Community E Class II equipment A Caution consult accompanying documents Type BF applied Part This symbol means serial number which is on the underside of the device and on the packaging CE CE Mark conforms to essential reguirements of the Medical Device Directive 93 42 EEC Important safety information Danger This unit must not be used in combination with the following medical devices e Internally transplanted electronic medical devices e g pacemakers e Electronic life support equipment such as respirators e Electronic medical devices attached to the body such as electroca
11. al display will light up blue for 2 3 seconds and then turn off again this is normal Hold Vv wf down the central power switch for 3 4 seconds The main display will light up blue and remain on 3 Remove your footwear and socks or stockings Your feet need to be completely bare to experience the ElectroVita micro current stimulation massage therapy 4 There are 10 different treatment programmes each offering a range of micro current massage therapies Select a number from 1 10 by pressing the P and P buttons We suggest you try all 10 over time to decide which best suits you 5 Sit in a comfortable chair Place your bare feet on the left and right foot plates Increase the intensity levels for each foot by pressing the to increase the intensity and W to decrease for BAND 1 The intensity level ranges from O to 40 slowly increase the level until you begin to feel the micro current stimulation For a full explanation of setting the intensity refer to page 13 Important safety information 1 Please read these instructions thoroughly before use 2 Please check that you have all of the component parts as detailed in this user manual 3 Take all parts out of the plastic bags and examine them to familiarise yourself with the components Notes on Safety The icons and warning signs are indicated here for your safety and correct usage of the product as well as to prevent injuries and or damage to properties
12. ation may lead to traffic accident Do not leave the Electrode Pad attached to the skin after treatment Prolonged attachment may cause skin irritation or infection Be careful not to allow any metal object such as a belt buckle or necklace to come into contact with the Electrode Pad during treatment You may receive a strong electrical shock Do not use cellular phones or other electronic devices near this unit Do not use this unit to treat one region for a long time more than 25 minutes The muscles of the region under treatment may become exhausted and may cause poor physical condition Put the Long Life pads only on skin or on the storage tray to avoid damage of the adhesive surfaces of the pads Correct Disposal of This Product WEEE Waste Electrical and Electronic Equipment This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and co
13. e AC mains voltage prior to application of the test level 6 Guidance and manufacturer s declaration electromagnetic immunity The ElectroVita is intended for use in the electromagnetic environment specified below The customer or the user of the ElectroVita should assure that it is used in such an environment 19 Important Information Immunity Test IEC 60601 Compliance Electromagnetic Environment Guidance Test Level Level Conducted RF 3V ms 3V m Portable and mobile RF communications eguipment IEC 61000 4 6 150kHz to should be used no closer to any part of the ElectroFlex 80MHz including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance d 12vP Radiated RF 3V ms 3V ms IEC 61000 4 3 26MHz to d 12P 80MHzto 800MHz 25GHz 10V m 26MHz to d 23 P 80MHzto 2 5GHz 2 5GHz Where P isthe maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation Distance in metres m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey a should be less than the compliance level in each frequency range b Interference may occur in the vicinity of equipment marked with the following symbol c 6 NOTE 1 At 80MHz and 800MHz the higher frequency range applies NOTE 2 These guidelines may not apply in a
14. e unit Do not insert the electrode cord plug into any place other than the electrode cord jack of the main unit May cause an electric shock or accident Do not disassemble or remodel this unit May cause fire dysfunction or accident Caution If the unit is not functioning properly or you feel discomfort stop using the unit immediately If you feel any problems with your body or skin consult your medical practitioner and follow their instructions If you want to move the Electrode Pad to another region or your body during treatment be sure to turn off the power If not you may receive a strong electrical shock Do not try to attach the Pads to any other person during the treatment You may receive strong electrical shock Do not start treatment while wearing an electronic device The settings and timings of the device may be affected Do not use in the presence of flammable anaesthetic gas mixture with air oxygen or nitrous oxide Important safety information Do not use this unit on infants or people not capable of expressing their intentions May cause an accident or ill health Do not use this unit in places with high humidity such as bathrooms or while taking a bath or shower You will receive a strong electrical shock Do not use this unit while sleeping The main unit may develop a malfunction or the pad may move to an unexpected region and cause ill health Do not use this unit while driving Receiving sudden strong stimul
15. est Level Level Electrostatic 6 kV contact 6 kV contact Floors should be wood concrete or ceramic tile discharge ESD 8kWVair 8kWVair If floors are covered with synthetic material the IEC 61000 4 2 relative humidity should be at least 30 Electrical fast 2kVforpower 2kVforpower Mains power quality should be that of a typical transient burst supply lines supply lines commercial or hospital environment IEC 61000 4 4 1kV for 1kV for input output input output lines lines Surge 1kVline s 1kVline s Mains power quality should be that of a typical IEC 61000 4 5 and neutral and neutral commercial or hospital environment Voltage dips short lt 5 UT lt 5 UT Mains power quality should be that of a typical interruptions and gt 95 dip in UT gt 95 dip in UT commercial or hospital environment If a dips or an voltage variations for05 cycle for 05 cycle interruption of mains power occurs the current of the onpowersupply 40 UT 40 UT ElectroFlex may be dropped off from normal level it input lines 60 dip in UT 60 dip in UT may be necessary to use uninteruptable power IEC 61000 4 11 for 5 cycles for 5 cycles supply ora battery 70 UT 70 UT 30 dip in UT 30 dip in UT for 25 cycles for 25 cycles lt 5 UT lt 5 UT gt 95 dip in UT gt 95 dip in UT for 5s for 5s Power frequency 3A m Not applicable Not applicable 50 60 Hz magnetic field IEC 61000 4 8 NOTE UT is th
16. intensity using Band 2 5 Gently increase the intensity setting by pushing the button A Or decrease intensity setting by pushing the button Ne See Figure 8 The LCD will show the level selected see Figure 9 When you reach the desired Level the icon will blink To stop the blinking and maintain the intensity press the button 5 times 6 To terminate the massage period turn off the unit a tanytime by pressing the on off Button for 3 seconds The unit has an auto timer it will start to count down from 25 minutes of massage and switch off automatically If you want to use with 2 gel pads only then you must connect 1 gel pad to Jack A and 1 gel pad to Jack B Care of your Gel Pads Never stick two adhesive pads to each other Keep the adhesive gel pads clean do not expose them to high temperature or direct sunshine If the electrode gel pads are insufficiently adhesive or dirty wipe with a damp or change for new ones Replacement parts will be available directly from BioEnergiser or your distributor Do not clean the electrode gel pads with any chemical ALWAYS try and protect the gel pads store on the gel pad protector when not in use as illustrated How to operate Connect with the supplied AC DC Power Adapter Plug the DC plug of the power supply into the socket on the side of ElectroVita see Figure 10 Plug in power adaptor to a suitable wall socket Make sure that the input voltage of the wall socket is s
17. ll situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people a Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the ElectroVita is used exceeds the applicable RF compliance level above the ElectroVita should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as re orienting or relocating the ElectroVita b Over the frequency range 150kHz to 80MFz field strengths should be less than 3V m 20 Important Information 7 Recommended separation distances between portable and mobile RF communications equipment and the ELECTROVITA The ElectroVita is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer or the user of the ElectroVita can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment transmitters and the ElectroVita as recommended below according to the maximum output power of the communications equipment
18. nditions of the purchase contract This product should not be mixed with other commercial wastes for disposal This product does not contain any hazardous substances Disposal of used batteries should be carried out in accordance with the national regulations for the disposal of batteries Important safety information Important information regarding Electro Magnetic Compatibility EMC With the increased number of electronic devices such as PC s and mobile cellular telephones medical devices in use may be susceptible to electromagnetic interference from other devices Electromagnetic interference may result in incorrect operation of the medical device and create a potentially unsafe situation Medical devices should also not interfere with other devices In order to regulate the requirements for EMC Electro Magnetic Compatibility with the aim to prevent unsafe product situations the EN 60601 1 2 2001 A1 2006 standard has been implemented This standard defines the levels of immunity to electromagnetic interferences as well as maximum levels of electromagnetic emissions for medical devices This medical device manufactured by TV Products HK Ltd conforms to this EN 60601 1 2 2001 A1 2006 standard for both immunity and emissions Nevertheless special precautions need to be observed Do not use mobile cellular telephones and other devices which generate strong electrical or electromagnetic fields near the medical de
19. ot plates correctly Gel pads not attached correctly to the skin Gel pads overlap each other Hectrode cord not connected correctly Applied intensity too weak Dampen the sole of your feet this will increase conductivity Ensure both of your soles are aligned on each foot plate correctly Attach gel pad firmly to the skin Reattach Long Life pads with no overlap Connect electrode cord correctly Increase the intensity by pressing the intensity button The skin tums red or the skin feels irritated Hygiene Adhesive surface of Gel pads is dirty or dry Adhesive surface of Gel pads damaged After using the product e Clean the device with a soft damp cloth to clean the foot plate area e Store the electrode gel pads on the protectors provided Storage Wash adhesive surface of gel pads carefully whilst unplugged from machine and leave to dry thoroughly Replace gel pads Keep the product clean and dust free store within the following condition Storage temperature and humidity 10 C to 60 C 10 to 95 RH Operating temperature and humidity 10 C to 40 C 30 to 90 RH 16 Troubleshooting and Maintenance Product Name ElectroMt a Circulation Massager Electrical Stimulator Model BE109 Power Supply 45V DC or 3 x 1 5V Alkaline Batteries Type C Supplier of Adaptor Golden Profit Electronics Ltd Adaptor Input 230V 50Hz 100mA Model Number of Adaptor SY 04010 BS Adaptor Input
20. ptor J ack Cable connecting the Electrode Gel Pads and Device Built in Ergonomic Carrying Handle Electrode Gel Pads to target specific areas of pain and swelling Additional Sole Massage Roller Plastic Protector spare for Gel Pads Functions and programmes Control Panel LCD showing the ntensity Level LCD showing the Intensity Level for feet maximum 40 Levels for body maximum 40 Levels LCD showing the Timer LCD showing the Program B Indication from 1 10 Modes A To switch the unit on or off B Choose from one of the 10 pre programmed massage programs Upward C Choose from one of the 10 pre programmed massage programs Downward D Increase the output intensity of foot BAND 1 FROM 1 40 LEVEL E Decrease the output intensity of foot BAND 1 FROM 1 40 LEVE F Increase the output intensity of body BAND 2 FROM 1 40 LEVE G Decrease the output intensity of body BAND 2 FROM 1 40 LEVEL Electrode Area On the device Figure 1 the black colour area on the device which is the electrode area for the sole On the gel pad Figure 2 the black colour area on the sticky part is the electrode area for the body size is 5 cm x 9 cm Circulation Enhancer output wave forms Foot Electro Therapy Massage We will examine the operation in more detail later in your instructions but the principle is relatively easy to understand There a
21. rdiographs Using this unit with other electronic medical devices may cause erroneous operation of those devices Warning Persons with the following conditions must consult the doctor before using this unit e Acute disease Malignant tumor Infectious disease Pregnancy Cardiac dysfunction High fever Abnormal blood pressure Skin sensory disorders or skin problems Receiving medical treatment especially those feeling discomfort May cause an accident or ill health Should not be used by persons in the first trimester of pregnancy fitted with a pacemaker or AICD or being treated for an existing deep vein thrombosis Do not use this unit near the heart above the neck on the head around the mouth or on diseased skin May cause an accident or ill health Application of electrodes near the thorax may increase the risk of cardiac fibrillation Do not use this unit simultaneously with other therapeutic devices or in combination with ointments including spray type ointments May cause discomfort or ill health Simultaneous connection of a PATIENT to h f surgical EQUIPMENT may result in burns at the site of the STIMULATOR electrodes and possible damage to the STIMULATOR Operation in close proximity e g 1 m to a shortwave or microwave therapy EQUIPMENT may produce instability the STIMULATOR output Do not use this unit for purposes other than treatment indicated in this manual May lead to accident problems or failure of th
22. re two separate controls channels one for the feet being band 1 and one for the pads being band 2 Place your feet on the foot plates turn on ElectroFlex with the central on off switch hold down for 3 seconds to activate choose one of the 10 different treatment programmes and start to increase the intensity to a comfortable level There are 40 different levels When you start to feel the mild electro therapy will depend on your own nerve sensitivity Certain individuals will feel nothing until the intensity is up at a high level others will feel the stimulation at relatively low levels This is completely normal Body Toning If you choose to tone muscle groups or target pain in other areas of your body the ElectroFlex comes with four gel pads These can be used to tone arms hips thighs abs or buttocks or target neck muscle or back pain The Outputs have no DC Component Output Waveform BAND 1 SOLE MASSAGER during 1 kQ load BAND 2 BODY MASSAGER during 1 kQ load MODE OUTPUT MODE OUTPUT 1 Pulse rate 6Hz with 1 second in left side right T Pulse rate 13Hz 80Hz with 13 seconds and o side off time 1 second then Pulse rate 6Hz with time in 1 sec A cycle repeating 1 second in right side left side off time 1 second A cycle repeating 2 Pulse rate 13Hz 80Hz with 18 seconds and o time in 1 sec A cycle repeating 2 Pulse rate 12Hz 80Hz with 12 seconds and off time in 1 sec A cycle repeating 3 Pul
23. se rate 13Hz 80Hz with 19 seconds and of time in 1 sec A cycle repeating 4 Pulse rate 13Hz 80Hz with 7 seconds and off time in 1 sec A cycle repeating 3 Pulse rate 7Hz with 30 seconds and off time in 1 sec A cycle repeating 4 Pulserate 7Hz 25Hz with 8 seconds and off time in 1 sec A cycle repeating 5 Pulse rate 13Hz 80Hz with 16 seconds and o time in 1 sec A cycle repeating 5 Pulse rate 12Hz 80Hz with 11 seconds and off time in 1 sec A cycle repeating 6 Pulse rate 13Hz 80Hz with 10 seconds and of time in 1 sec A cycle repeating 6 Pulse rate 12Hz with 12 seconds and off time in i 7 Pulse rate 13Hz 80Hz with 17 6 seconds and 1 sec A cycle repeating off time in 1 sec A cycle repeating 7 Pulse rate 11Hz 80Hz with 15 seconds and off ame 8 Pulse rate 12Hz with 10 seconds and off time in time in 1 sec A cycle repeating 1 sec A cycle repeating 8 Pulse rate 12Hz with 10 seconds and off time in 1 sec A cycle repeating 9 Pulse rate 12Hz with 16 seconds and off time in 1 sec A cycle repeating 9 Pulse rate 12Hz with 13 seconds and off time in 1 sec A cycle repeating 10 Pulse rate 12Hz 80Hz with 10 seconds and off time in 1 sec A cycle repeating 10 Pulse rate 12Hz 80Hz with 11 seconds and off time in 1 sec A cycle repeating 10 ElectroVita output wave forms Foot Massager EMS Waveform and Pulse
24. sing the unit This unit should not be used by people prohibited from doing so in Notes on safety Environment This unit is intended for home use only Effectiveness Massage relief of muscle pain stiffness and fatigue Precautions for use Please read Notes on safety before using the unit Electronic Nerve Stimulation is a non invasive safe nerve stimulation intended to reduce pain The ElectroVita Circulation Massager uses proven neuromuscular electrical stimulation therapy to send micro current pulses through the soles of your feet This type of electrical stimulation is clinically proven to be safe and effective and can be carried out in the comfort of your own home The ElectroVita Circulation Massager improves muscle function by stimulating nerves increasing the flow of blood helping to reduce PAIN SWELLING TIRED AND ACHING LEGS Medical Purpose This Electronic Nerve Stimulator is intended to be used as a massager to relieve muscle pain increase blood circulation relax stiff muscles reduce swollen feet ankles and relieve fatigue The massaging effect is achieved by electronic stimulation of the nerves through electrode pads placed on the skin or through the foot plates Various massage regions and treatment programs can be selected To obtain a correct treatment you have available 10 treatment programs see table below A treatment program runs for 25 minutes Mode Complaint Program Effec
25. t 1 Stiff shoulders Tapping massage Different vibrations promote blood circulation and relieve fatigue 2 Swelling and Prickly massage Different stimulation promote circulation of foot fatigue blood and body fluid in the feet 3 Acute Pain Combined massage High freguency vibrations relieve acute pain promptly 4 Acute elbow or Pulsed prickly massage High freguency vibrations relieve acute knee pain pain promptly 5 Am fatigue Tapping massage 2 Promote Blood circulation with different stimulation 6 Swelling and Fast tapping massage Different stimulation promote circulation of calf fatigue blood and body fluid in the limbs 7 Back pain or lower Fast tapping prickly massage A low frequency to promote blood circulation back stiffness and relieve pain neuralgia 8 Stiff muscles Very fast tapping prickly massage A low frequency to promote blood circulation numbness This program is effective over along period 9 Various Symptoms Pulse prickly massage 2 Relieves stiffness pain and fatigue 10 Various Symptoms Fast tapping with pulse massage Relieves stiffness pain and fatigue Machine overview and part names Output for the feet Electrode Silicon Area for Foot Treatment LCD Display Screen Output for Body for connecting Gel Pads cable jack for Body Massage Treatment Sole Massage Roller The EletroFlex Circulation Massager is also supplied with an AC DC Adaptor not illustrated Ada
26. u reach your desired intensity level release the button the icon will blink To stop the blinking and maintain the intensity press the A button 5 times 4 You can adjust the program anytime Once re adjusted the intensity will return to O So you will have to increase the intensity to the desired level The LCD will also show the level which you have selected See Figure 5 To terminate the massage period you can turn off the unit anytime by pressing the on off button for 3 seconds The unit has an auto timer it will start to count down from 25 minutes of massage and switch off automatically t wt E PROGRAM M 4 Fig 1 Fig 2 Fig 3 12 How to operate For Body BAND 2 Using the Gel Pads Connect the output wire to the gel pads Connect the other end of the output wire to the output jack on ElectroFlex Remove the protective film from the adhesive pads Attach the gel pads to the skin Press the on off button for 3 seconds to turn on the unit andadjust the stimulating mode and output intensity to the desired level The display will show the mode and level that you selected and start to count down 1 Plug the 2 cables into the cable jack at the side of the unit See Figure 6 2 Connect pin of the cable to the gel pad See Figure 7 3 Remove the protective film from the gel pad and attached the 4 pads to the area of the body you wish to treat 4 Repeat operation as in foot instructions adjust the
27. uitable for the supplied adaptor Inserting Batteries If you want to use the ElectroVita with battery powerinstead of the supplied main adaptor the battery compartment is located on the underside of the unit Remove the battery cover from the unit by removing the screw with a screwdriver Insert three new 1 5V size C batteries with the and marks correctly aligned Note on batteries Do not mix different types of batteries or an old battery with a new one To prevent the risk of leakage or explosions never recharge the batteries apply heat or take them apart When not using batteries remove them to prevent battery drainage If liquid leaks from the batteries throw them away Thoroughly clean the battery compartment with a dry cloth Changing the Sole Massage Roller The sole massage roller is interchangeable The roller is fixed into position between the two locking locators These push in to the main body of the ElectroVita to hold the sole massage roller firmly in place To Remove the locking locators you will need to squeeze the locator on the outside face this will push the locking locator out of its fixed position and allow you to remove and change the roller Cleaning A Electrode Gel pad e When not in use store the electrode gel pads on the plastic pad protectors provided at room temperature Keep the electrode gel pads clean and dust free in a dry location keep away from oily or
28. vice This may result in incorrect operation of the unit and create a potentially unsafe situation Recommendation is to keep a minimum distance of 7m Verify correct operation of the device in case the distance is shorter BE109 needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the ACCOMPANYING DOCUMENTS Portable and mobile RF communications equipment can affect the BE109 Circulation Enhancer WARNING that the use of accessories transducers and cables other than those supplied with the exception of the transducers and cables sold by the manufacturer of the BE109 Circulation Enhancer as replacement parts for internal components may result in increased EMISSIONS or decreased IMMUNITY of BE109 Circulation Enhancer WARNING that BE109 Circulation Enhancer should not be used adjacent to or stacked with other equipment What is electronic nerve stimulation INTENDED USE Medical Purpose This Electronic Nerve Stimulator is intended to be used as a massager to relieve muscle pain increase blood circulation relax stiffness muscles reduce swollen feet and ankles and fatigue The massaging effect is achieved by electronic stimulation of the nerves through electrode pads placed on the skin or through the foot plates Various massage regions and treatment programs can be selected Suitable Users Please read Notes on safety before u

Instructions

Contents

Download Pdf Manuals

Related Search

Related Contents