PowerPoint 프레젠테이션 - Bosch Security Systems
Contents
1. BOSCH fe 1 Opening the cover 2 Camera Lens installation 3 Feed through Wiring Open the cover by unlatching the three Remove the two screws holding the Remove the two dome plugs located latches on the side of the housing camera tray to the housing Remove tray inside the housing Screw the two 3 8 If the optional tamper resistant screws from the housing Attach the lens to the inch NPT fittings into the foot Pull the have been installed use the supplied camera Use the various 1 4 20 screws cabling through the fittings into the wrench to remove the screws before and spacers provided to mount the housing Tighten the fitting and attach the opening the latches camera and the lens to the camera tray foot to the top bracket of the mount Ensure that the holes in the rear cap are covered with the rubber plugs provided 4 Power Connections The terminal block accepts wire ranging from 0 5 mm to 2 5 mm 20 AWG to 14 AWG To attach the external safety ground wire remove the nut the washers and the external ground wire lug from the ground post Strip and crimp the external ground wire into the lug Reattach the ground connections in the order shown in the side figure Tighten the fitting to 8 5 N m to 9 0 N m 75 in Ib to 80 in Ib 5 Wiring All Models except UHO HBPS 10 UHO HBPS 50 and UHO HPS 50 Connect the supply power wires to the terminal block Strip no less than 6 mm 0 25 in and no more than2. 8 mm 0 31 in of insulation away from the wire Ensure not to nick the wires Cut the power cord on 120 VAC and 230 VAC camera models leave enough cable to allow connection to the terminal block Strip no less than 6 mm 0 25 in and no more than 8 mm 0 31 in of insulation away from the wire Connect these wires to the connectors provided on the terminal block O Ground cable to housing top i p porearea BNC cable to camera a Power input connector m cc in orm Power conection 6 Video coax connection Install a 1 2 in NPT fitting into the available hole in the rear cap Route the video coax cable through one of the fittings installed or one of the feed through fittings in the base Attach the BNC connector to the coax and connect it to the camera Tighten the fitting to 8 5 Nmto9 0 Nm 75 in lb to 80 in Ib 7 Lens wiring Install the 3 8 in NPT fitting into the middle hole in the rear cap If installing a zoom lens insert the lens control cable through the last fitting at the rear of the BOSCH housing Attach the lens wiring to the lens mating connector and connect it to the lens If a mating connector is not available connect directly to the lens cable Tighten the fitting See step 6 8 Wiring UHO HBPS 10 50 UHO HPS 50 Cut the power cord on 230 VAC camera models leaving enough cable for connection to the terminal block Strip no less than 6 mm 0 25 in and no more than 8 m
3. m 0 31 in of insulation away from the wire Be sure not to nick the wires Insert the power cord through the back shell assembly and strain relief Connect the power cable to the screw terminals on the provided mating connector 9 Final assembly 10 Sunshield installation 1 Use the hole plugs provided to plug 1 Loosen the two screws M4 x 10 on any unused holes in the rear cap the top of the housing 2 Replace the camera and bracket 2 Slide the sunshield to the desired back into the housing position It has a range of 50 mm 2 in 3 Slide the camera lens tray into the 3 Tighten the screws to lock the slot near the clasp side of the housing sunshield into position 4 Install screws 4 If the sunshield is removed or not 5 Close the cover and secure the installed plug the two screw holes with latches the hole plugs supplied with the housing 6 Optional tamper resistant screws hardware kit are provided with the housing Secure the latch using these three screws and the provided tamper resistant wrench Pin Fonction Mees wie coer 3 No Connection Do not use 11 Fuse replacement 1 To replace a fuse pull the top of the fuse holder 2 Replace the fuse with a fuse that has the same current rating The fuse is a 5 2 mm x 20 mm slow blow breaking capacity cartridge type fuse 24 VAC 4 A 250 VAC 120 VAC 2 A 250 VAC 230 VAC 2 A 250 VAC There is a spare fuse inside the housing Downl
4. oad the English version of the User Manual here http us boschsecurity com us product 02 roducts 3 st bu f 277305 tams catalo rod us st section f 277848 ta ms _ catalo rod us st prodfam 2 7848 tams catalo rod us 278254 OR from the page of UHO Series Outdoor Camera Housing on your country s site linked from boschsecurity com Bosch Security Systems B V Torenallee 49 5617 BA Eindhoven The Netherlands www boschsecurity com Bosch Security Systems B V 2014
Download Pdf Manuals
Related Search