OWNER`S MANUAL
Contents
1. Installing the unit Be sure you test all connections first and then follow these steps to install the unit 1 Make sure the ignition is turned off and then disconnect the cable from the vehicle battery s negative terminal Disconnect the wire harness and the antenna Press the release button on the front panel and remove the control panel see the steps of removing the front panel Lift the top of the outer trim ring then pull It out to remove it The two supplied keys release tabs inside the units sleeve so you can remove it Insert the keys as far as INSTALLATION they will go with the notches facing up into the appropriate slots at the middle left and right sides of the unit Then slide the sleeve off the back of the unit Sleeve 2 L Key Outer Trim Ring Front Panel 6 Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver Not all tabs wil be able to make contact so examine which ones will be most effective Bending open the appropriate tabs behind the dashboard to secure the sleeve in place Dashboard Sleeve 7 Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables 8 Slide the unit into the sleeve until it locks into place 9 Tofurther secure the unit use the supplied metal strap to secure the back of the unit in place Use the2. 0 0 6 CLAS 1 MODE PAIR 17 SCAN amp 2 S release button 18 0 DSP 3 hang up LOU BND 19 AS PS 4 VOL SEL MENU Audio knob 20 8 EQ 5 p gt 21 7 MON 6 MUTE 22 T MENU TRANS 7 LCD 23 4 8 4 SHF 24 pick up 9 5 DIR 25 Reset button 10 1PAU 26 SD MNC interface 11 2 SCN 2 Mic 12 3 RPT 28 eject button 13 AUX IN 29 disc slot 14 6 DIR 30 IR 15 USB interface 16 9 LOC OPERATION BASIC OPERATION SWITCHING ON OFF THE UNIT Press putton 6 to turn on the unit When the unit is on press and hold XD button 6 to turn the unit off FACEPLATE RELEASE Press button 2 removable faceplate to detach the SOUND ADJUSTMENT Press SEL button 4 to enter AUDIO SETTING mode use SEL button 4 to select the desired adjustment mode The adjustment mode wil change in the following order VOL Bass Treble Balance Fader Exit Press 4 to adjust the sound quality up or down step by step Press MUTE button 6 will mute the sound press it again will resume the sound LOUDNESS Press LOUD button 3 for several seconds to switch loudness function on and LOUD will appear on the LCD for several seconds Press it for several seconds again to release this function DISPLAY Press DSP button 18 to change display mode LOCAL Press LOC button 16 to select between local and distant stations Local setting for reception of strong station and a distant
3. PLCD5MRBTS OWNER S MANUAL Mobile Audio System N P V NEW A 3 a 2 j P ai l vv ow aw 6 w MODE wae pak O0 0 1 gt ae A 9 EON CLAS p ma ins ll PLL Synthesizer Stereo Radio PLL RADIO MP3 CD CD RW Compatible Automatic Memory Storing USB amp SD MMC Card Interface Fold Down Detachable Panel Auxiliary Input Function Bluetooth Hands free function amp A2DP Advanced Audio Distribution Profile Stereo Audio Transmission www pyleaudio com 1 5 Installation 3 Take out screw before installation 3 DIN Front Mount Method A 3 Installing the unit 3 Removing the unit 4 DIN Rear Mount Method B 5 Using the detachable front panel 6 Wiring Connection 7 ISO CODecllOD cH 7 Location of keys 8 Basic operation 9 Switching on off the unit 9 Faceplate release 9 Sound adjustment 9 9 DISDIAY 9 ste
4. DIN REAR MOUNT Method B If your vehicle is a Nissan Toyota follow these mounting instructions Use the screw holes marked T Toyota N Nissan located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle Side View showing Screw Holes marked T N Dashboard or Console To fasten the unit to the factory radio mounting brackets Align the screw holes on the bracket with the screw holes on the unit and then tighten the screws 5x5mm on each side Note the outer trim ring sleeve and the metal strap are not used for method B installation USING THE DETACHABLE FRONT PANEL To Detach the Front Panel 1 Press the release button then the front panel will be folded down 2 When the two sides fixed into place push the front panel into main unit 3 Note that if the front panel fails to lock in position properly pressing control button may not function and the display may be missing some segments Press the release button and then reinstall the front panel again 2 To remove the front panel lift it up at a little angle from horizontal position then first pull out the right side and then pull out the left side Precautions when handling 1 Do not drop the front panel 2 Do not put pressure on the display or control buttons when detaching or re installing the front panel 3 Do not touch the contacts on the front pa
5. REMOTE CONTROL HANDSET OPTIONAL YO 3 8 9 Q 8 d3 2 12 T 41 10 18 16 FUNCTION KEY amp CONTROL 1 POWER Power ON OFF Button 2 DSP 0 Display Button _ 0 For MP3 WMA Operation SEL sound Mode Select Button Character Shift Right For MP3 WMA Operation 4 VOL Volume Up Button Character Select A B 8 9 0 For MP3 WMA Operation 5 VOL Volume Down Button Character Select A B 8 9 0 For MP3 WMA Operation 6 BND LOU ENT Band Select Button When pressed shortly Loudness Button When pressed long Enter Button For MP3 WMA Operation 7 MODE 7 Mode Button S T U 7 For MP3 WMA Operation 8 TUNE SKIP CHi 8 Tune SKIP Down Button V W X 8 For MP3 WMA Operation 9 TUNE SKIP CH 1 9 Tune SKIP Up Button Y Z SPACE 9 For MP3 WMA Operation 10 AS PS D AUD Automatic Memory Storing amp Program Scanning Button Mode Select Button For MP3 WMA Operation 11 M1 M6 Preset Buttons A R 1 6 For MP3AWMA Operation 12 PAU Pause Button A B C 1 For MP3 WMA Operation 13 SCN Scanning Button D E F 2 For MP3 WMA Operation 14 RPT Repeat Button GH l 3 For MP3 WMA Operation 15 SHF Shuffle Button J L 4 For MP3 WMA Operation 16 LOC S MOD Local Distant Select Button 19 TROUBLE SHOOTING Before going through the checklist check wiring connection If any of the problems persist after checklist has been made consult your nearest service dealer symptom Son The car ignition switch is If t
6. can select desired directory and press SEL button to enter it After selected a song then press BND LOU or SEL button to play DISPLAY ID3 INFORMATION Press DSP button 18 to show the ID3 TAG title artist and album SUPPORT MP3 WMA DECODING MODE The main unit supports MP3 AWMA Windows Media Audio decoding modes as below Bit Rate Supports MPEG 1 Audio 32 48 64 96 Stereo Layer 3 128 192 256 44 1kHz 320 Media Audio 44 1kHz The USB solution can support 1 Folder 500 max 2 File 999 max 3 Depth of folder 8 layers 4 Size 2 GB DISC NOTES A Notes on discs 1 Attempting to use non standard shape discs e g square start and heart may damage the unit Be sure to use round shape CD discs only for this unit Do not stick paper or tape etc onto the label side or the recording side of any discs as it may cause a malfunction OPERATION 3 Dirt dust scratches and warping discs will cause mis operation B Notes on CD Rs recordable CDs CD RWs rewritable CDs 1 Be sure to use discs with following marks only for the unit to play dise wise UIS DIGITAL AUDIO DIGITAL AUDIO 211910118 ReWritable 2 The unit cannot play a CD R and CD RW that is not finalized Please refer to the manual of your CD R CD RW recorder or CD R CD RW software for information on finalization process Depending on the recording status conditions of the disc and the equipment used for the
7. of range the connection will be lost when you come back to the unit reconnection is necessary 2 When the mobile phone is out of range from the unit and there is an incoming call when you come back to the unit and you want to transfer the audio to the unit you need to reconnection 3 When you press button 2 to release the front panel the connection will be break off When you install the front panel you need to reconnection 4 If you turn off the mobile phone that has paired with the unit when you turn on the mobile phone you need to reconnection T MENU When successful paired Press T MENU button 22 on the front panel will enter the telephone menu keep pressing this button or press 44 button 23 5 to change the items in this menu The items will be displayed in the following sequence PRE NUM RECELVED DIALED MISSED PHONE BK MANU ANS TALK The details please see the following instruction 1 RRE NUM You can save 10 phone call to the phonebook 1 In PRE NUM mode rotating button 4 to select the NUMBER Then press SEL button and enter the phone number Then press SEL button again to save it to phonebook 1 If you want to delete a number from phonebook 1 After Selected the number then press and hold BND LOU key for 2 seconds The number will be deleted 2 RECELVED Display the last call you have received memory 10 numbers 3 DIALED Display the last dial
8. setting for reception of weaker stations This function is effect during SEEK operation MONO Press MON button 21 to select mono or stereo mode You can sometimes improve reception of distant stations by selection EQUALIZATION Press EQ button 20 shortly to turn on equalization function and to select desired audio mode There are five kinds of mode as below CLAS POP ROCK EQ OFF RESET FUNCTION RESET button 25 must be activated with either a ballpoint pen or thin metal object The RESET button is to be activated for the following reasons Initial installation of the unit when all wiring is completed All the function buttons do not operate Error symbol on the display Note if press RESET button 25 the unit can t work yet please use a cotton swab soaked in isopropyl alcohol to clean the socket on the front panel MODE SELECTION Press MODE button 1 to change the mode among Radio USB CARD IPOD optional AUX and BT Audio SYSTEM SETTING Press and hold SEL button 4 on the front panel to enter SYSTEM SETTING mode There are below items to adjust BEEP P VOL AREA HOUR 24H Use SEL button 4 to select the item you want to change and use SEL button 4 to change the corresponding setting 1 BEEP ON OFF Beep on There is a beep sound when buttons is pressed Beep off There is no beep sound when buttons is pressed 2 P VOL P VOL The max volume value when you turn
9. shockproof about 70 seconds around for MP3 WMA SELECTING DIRECTORY UP DOWN Press DIR button 9 or DIR button 14 to select directory downward or upward If the USB driver does not contain any directory there is no function of pressing DIR button 9 or DIR button 14 SELECTING TRACKS Searching Track Directly Press AS PS SCH button 19 for one time It enters into Searching track directly mode The unit searches the track selected by following direct numeric buttons M1 M6 7 MON 8 EQ 9 LOC 0 DSP Maybe you can rotating the button 4 to select the numbers If selected three digits the unit searches the tract at once If selected one or two digits the unit wait for BND LOU or SEL button for seconds The unit searches the track after few seconds even if the enter button is not pressed Searching Directory or File Name Press AS PS SCH button 19 for two times It enters into Searching Directory or File Name mode The unit searches files and directories that have the same character which is inputted by the user pressing the corresponding buttons listed on the below DOWN TUNE SEEK TRACK DOWN bae OPERATION eem Y Z SPACE 9 CHARACTER SHIFT PUSH SEL RIGHT U CHARACTER SELECT AUDIO KNOB A B 8 9 0 _ Explain as follows Use the corresponding buttons Or you can using button 4 to select the characters A to Z blank 0 to 9 _ Press SEL button 4 to con
10. supplied hardware Hex Nut M5mm and Spring Washer to attach one end of the strap to the mounting bolt on the back of the unit If necessary bend the metal strap to fit your vehicle s mounting area Then use the supplied hardware Tapping Screw 5x25mm and Plain Washer to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard This strap also helps ensure proper electrical grounding of the unit Note to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard Spring Washer Hex Nut Metal Strap Mounting Bolt x ARMS lt po Q 2 EN lt Plain Washer S amp Tapping Screw 10 Reconnect the cable to the vehicle battery s negative terminal Then replace the outer trim ring and install the unit s front panel see the steps of installing the front panel Removing the unit 1 Make sure the ignition is turned off then disconnect the cable from the vehicle battery s negative terminal 2 Remove the metal strap attached the back of the unit if attached 3 Press the release button to remove the front panel INSTALLATION 4 Lift the top of the outer trim ring then pull it out to remove it 5 Insert both of the supplied keys into the slots at the middle left and right sides of the unit then pull the unit out of the dashboard
11. tons 9 neset MUNCION ouo conie 9 Mode 9 System 9 9 Radio operation 10 selecting the frequency band 10 CA NEIN E 10 Station storing 10 CD MP3 WMA operation 10 Switching to CD mode 10 Selecting tracks 10 t 10 Previewing all tracks 11 Repeating the same track 11 Playing all tracks in random 11 Ez Ro To ERE MAE 11 Disc notes eeeee mmm 12 USB play operation 13 SD MMC operation 13 Bluetooth operation 15 Preparing for operation 15 FUMING sm uo 15 COMME CE RT REC LER 15 e etd dest 15 PMSWEHING 16 Making an outgoing call 16 Transfer the call between mobile phone the ree 16 Bluetooth audio A2DP function 17 Specification 18 Remote Control 19 Trouble shooting 20 INSTALLATION Notes Choose the mounting location where the unit will not interfere with the normal driving function of the driver Be
12. will return to seek tuning mode AUTO appears on the display AUTOMATIC MEMORY STORING amp PROGRAM SCANNING Automatic memory storing Press AS PS button 19 for several seconds SEARCH will appear on LCD the radio will search from the current frequency and checks the signal strength until one cycle search is finished And then 6 strongest stations are stored into the corresponding preset number button Program scanning Press AS PS button 19 shortly to scan preset station And the corresponding station number P1 P6 will flash on LCD SCAN Press SCAN button 17 to enter scan mode the unit will scan to higher frequency station and keep on each station for several seconds the corresponding frequency will flash 5 times on LCD STATION STORING Searched a station press preset button 1 6 for several seconds until 2 beeps come out current station is stored into the number button CD MP3 WMA OPERATION SWITCHING TO CD MODE If there is no CD MP3 WMaA disc inserted into the driver Gently insert the CD MP3 WMaA disc with the printed side uppermost into the disc compartment until you feel some resistance The disc will be drawn into the driver automatically CD MP3 WMA playback begins If a CD MP3 WMA disc is already inserted in the driver Keep pressing MODE button 1 shortly SELECTING TRACKS Press P 4 5 23 will skip to the OPERATION previous next file File num
13. ain will resume playing RPT Repeat When playing a song press RPT button 12 shortly will repeat the current song and S RPT will appear on the display Press it again to exit this mode Press it for about 2 seconds to repeat Album and D RPT will appear on the display Press it again to exit this mode SHF Shuffle When playing a song press SHF button 9 shortly after the current song play to the end It will play the song in current category in random order and SHF will appear on the display Press it again to exit this mode Press it for 2 seconds to play all songs in the album and D SHF will appear on the display Press it again to exit this mode TUNE TRACK UP DOWN When playing a song press P lt lt button 5 23 will play the next previous track in the current category but you can not enter to the next category When play a song more than 3 seconds Press lt lt button 23 will back to the start position When play a song less than 3 seconds press 44 button 23 will play the previous track When playing a song press and hold button PP lt lt 5 23 for several seconds will fast forward reverse of the playing And the display will show the playing time e g 1 20 BLUETOOTH OPERATION PREPAIR BLUETOOTH OPERATION 1 When use Bluetooth please make sure the mobile phone supports Bluetooth function ii For the different kind of mobile phone Bluetooth emiss
14. ber will showed on display Press and hold P 44 5 23 will fast reverse forward File play starts when you release the button PAUSING PLAYING Press PAU button 10 to pause and Pause will appear on LCD Press it again to resume play PREVIEWING ALL TRACKS Press SCN button 11 to play first several seconds of each file and SCN will appear on LCD Press again to stop scan and listen to file SCN will disappear Press and hold SCN button 11 will play first several seconds of each file in the current folder and D SCN will appear press it again will exit this mode REPEATING THE SAME TRACK Press button 12 to continuously repeat the same file and S RPT will appear on LCD Press it again to stop repeat and S RPT will disappear Press and hold RPT button 12 will repeat all the files in the current folder And D RPT will appear on LCD Press it again will exit this mode PLAYING ALL TRACKS IN RANDOM Press SHF button 8 to play all files in random order and S SHF will appear on LCD Press again to cancel the function and S SHF will disappear Press and hold SHF button 8 for 2 seconds will play all files in the current folder in random order And D SHF will appear on LCD Press it again will exit this mode EJECTING A DISC Press amp button 28 to stop CD MP3 WMA playing and eject the disc from the disc slot 29 be ESP FUNCTION OPTIONAL The unit can be
15. ction 2 Making an outgoing call by inputting the phone number manually Press button 24 on the front panel CALL will appear on LCD Use 0 9 4 buttons to enter the phone number you want to dial Note Press button will input character press and hold it will input character Then press button 24 again will call the number Note if you input the wrong number Press CLR button will clear it Press and hold CLR button will clear all numeric TRANSFER THE CALL BETWEEN MOBILE PHONE AND THE UNIT During the talking mode you can press and hold TRANSFER T MENU button 22 to transfer the phone call between the mobile phone and the unit Note 1 If you transfer the call to mobile OPERATION phone the mute of the present mode will be released at the same time 2 When making an outgoing call it s not possible to transfer if the call is not being answered yet e BT reset InBT AUDIO mode Press and hold BND LOU key for several seconds Some of the Bluetooth information and phone numbers will be lost BLUETOOTH AUDIO A2DP FUNCITON The unit supports Bluetooth audio function If your mobile phone can play stereo audio when the paring is ok you can choose the unit you have paired to play the stereo music M1 M2 button on the front panel of the unit serves as PAUSE PLAY and STOP control button It is up to the mobile phone the different mobile phone has the differe
16. ed OPERATION number memory 10 numbers 4 MISSED Display the call you have missed memory 10 numbers 5 PHONE You can copy 20 phone numbers from mobile to the phone book 2 of the unit via Bluetooth transmitted The way is In mobile phone gt enter phonebook gt more gt send via Bluetooth gt select number gt send If you want to delete a number from phonebook 2 After Selected the number then press and hold BND LOU key for 2 seconds The number will be deleted 6 MANU ANS manual answer You can set Answer mode to manual answer MANU ANS mode or Auto Answer AUTO ANS mode In auto answer mode when a call coming the Phone Number will appear on LCD The unit will answer the call automatically In MANU ANS mode when a call coming the Phone Number will appear on LCD you can press button 24 to answer the call or press button 3 to reject the incoming call 7 TALK 00 20 You can setting the Bluetooth volume in TALK 00 item If it is OO When there is a call coming the main volume will set to 60 automatically If you set TALK to 20 he main volume will set to 100 automatically when a call is coming Example TALK volume MAIN volume 00 60 01 62 02 64 20 100 MAKING AN OUTGOING CALL 1 Making an outgoing call from SPEED DIAL RECEIVED LIST DIALED LIST MISSED LIST PHONE BOOK Mobile Phone and PHONE BOOK SIM Card please refer to the T MENU se
17. firm entry of each characters Press BND LOU button 8 to start the title search In case the selected title is a directory name display will show then use the buttons 4 to list all songs under this directory and select the title Press BND LOU or SEL button to confirm and start the play Repeat the above steps if the newly selected title is again a directory Searching From Root Directory Press AS PS SCH button 19 for three times The unit searches file or directory from root by button 4 Display will list all available directories and songs Select the desired directory songs by using buttons 4 and BND LOU or SEL button to confirm If the selected title is a song it starts to play If the selected title is a directory name display will show then Use the buttons 4 to list all songs under this directory and select the title Press BND LOU or SEL button to confirm and start the play Repeat the above steps if the newly selected title is again a directory Searching FILE From Current Directory Press AS PS SCH button for four times The unit searches file or directory from current directory by button 4 The currently playing file name is displayed User can select the file by button 4 After selected a file Pressing BND LOU or SEL button to play If you would like to listen to a song which is in different directory Pleases select and press SEL button Then you
18. fore finally installing the unit connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle Install the unit where it does not get in the drivers way and cannot injure the passenger if there is a sudden stop like an emergency stop If installation angel exceeds 30 from horizontal the unit might not give its optimum performance 30 Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation methods TAKE OUT SCHEW BEFORE INSTALLATION Before install the unit please remove the two screws Take out screw before installation DIN FRONT MOUNT Method A Installation Opening This unit can be installed in any dashboard having an opening as shown below J 53mm J lt 182mm gt
19. he power supply is No power not on connected to the car accessory circuits but the engine is not moving switch the ignition key to ACC The fuse is blown Replace the fuse Temperature inside the car Cool off or until the ambient is too high temperature return to normal Condensation Leave the player off for an hour or so then gom again Naveound Volume is in minimum is in minimum Adjust volume to a desired level volume to a desired level Wiring is not properly Check wiring connection connected Saund skips The installation angle is Adjust the installation angle less dd more than 30 degree than 30 degree The operation The built in microcomputer Press the RESET button keys do not is not operating properly Front panel is not properly fix into work due to noise its place The radio does The antenna cable is not Insert the antenna cable firmly not Work The connected The signals are too weak select a station manually radio station automatic selection does not work 20
20. ive power has some difference To get the best conversation quality it is commended that the distance between the mobile phone and the unit is within 3m And please don t put any metal object or any obstacle between the path of the mobile phone and the unit PAIRING l ln any mode press and hold PAIR MODE button 1 on the front OPERATION 2 panel PAIRING will appear on the LCD 3 the mobile phone select the Bluetooth set up Please refer to the Instruction manual of your mobile phone on how to operate Bluetooth 3 CARBT should appear in the list on your mobile phone please select CARBT and then input password 0000 4 When successful paired CONN OK will be displayed on LCD 5 When pairing failed PAIR END will be displayed on LCD You can press and hold PAIR button 1 to try the pairing again 6 Note During Pairing MODE key will no functional during pairing mode When pairing you can press PAIR button 1 to terminate the pairing CONNECT This unit is built in auto reconnection function Every time when you short press button 24 the unit will auto reconnect with the mobile phone note the mobile phone must have been paired with the unit before In the following conditions you can reconnect manually by pressing RECON button 25 for several seconds when reconnect is successful Conn will be displayed 1 If the mobile phone is out
21. nel or on the main unit body It may result in poor electrical contact 4 dirt or foreign substances adhered on the contacts they can be removed with a clean and dry cloth 5 Do not expose the front panel to high temperatures or direct sunlight in 3 For safekeeping store the front panel in the supplied protective case immediately after being removed Protective Case Front Panel To Install the Front Panel anywhere 1 To install the front panel first insert the 6 K lati left side into proper position then insert Keep away any volatile agents e g the right side into place benzene thinner or insecticides from touching the surface of the front panel 7 Do not attempt to disassemble the front panel WIRING CONNECTION ISO CONNECTION Antenna Socket L ch WHITE LINE OUT R ch RED 4 SPEAKER SYSTEM o g GREEN BLACK 8 pA el F Rear Left i i Speaker amp GREEN 7 o WHITE BLACK 6 Front Left GRAY BLACK 4 Front Right wass J wd GRAY 3 VIOLET BLACK 2 Rear Right m 3 peakeF ji VIOLET 1 Ground Wire Black 12VAccessory Switch Red PowerAntenna AmplifierTum On Blue Memory12 Volt Constant Power Yellow OPERATION LOCATION OF KEYS DO 40 0902 4344 us de z E 2 E WON een 27 403 2130 2120 1918 171015
22. nt define Use 44 b button 23 5 on the front panel of the unit to choose the previous next track It is up to the mobile phone the different mobile phone has the different define SPECIFICATIONS GENERAL Bluetooth Connectivity Built in Bluetooth for Wireless Audio Streaming Works with All of Your Favorite Devices Bluetooth Version 2 1 Bluetooth Network Name Pyle Audio Bluetooth Network Password 0000 Hands Free Calling Ability Built in Microphone for Call Answering Telephone Number LCD Panel Digital Display Incoming Calls Automatically Appear Answer End Call Button Control Automatic Music Quiet Down with Incoming Calls Features In Dash Console Headunit System Bluetooth Wireless Streaming Ability USB Flash amp SD Memory Card Readers MP3 Digital Audio File Compatibility Front Loading CD Player AM FM Radio 30 Station Memory Presets Aux 3 5mm Input Connector Jack Ability to Connect Additional External Devices Rear RCA L R Output Connector Jacks LCD Digital Display Panel Bass Treble Balance Fader Adjustment EQ Audio Configuration Includes Wireless Remote Control Technical Specs Single DIN Universal Standard Size MPX PLL Tuning Radio Electronic Shockproof ESP Function Digital Audio File Compatibility MP3 WMA Maximum USB SD Card Support Size 32GB CD Support CD MP3 CD CD R CD RW Tone Controls 10dB Power Output 4 x 60 Watt Stereo Separation 45dB Power DC 12V
23. on the unit Such as when you set OPERATION the P VOL to 40 If the volume value is small than 40 when you turn off the unit Next time you turn on the unit The volume will keep the last volume value But if the volume value is large than 40 when you turn off the unit Then next time you turn on the unit The volume value will back to 40 3 Area Europe USA Use SEL button 4 to set the radio frequency to Europe frequency or USA frequency 4 HOUR 24 12 You can select time format to 12 hour or 24 hour format In AREA item When you change the radio frequency to the EUR The time format will be changed to 24 HOUR format automatically When you change the radio frequency to the USA The time format will be change to 12 HOUR format automatically AUXILIARY INPUT The unit can be connected to a portable audio player through the AUX IN jack 13 on the front panel After finishing the connection you can press MODE button 1 to switch the mode to AUX IN mode RADIO OPERATION SELECTING THE FREQUENCY BAND At radio mode press BAND button 3 shortly to select the desired band The reception band will change in the following order gt FM2 gt FM3 gt AM 7 SELECTING STATION Press gt P 44 buttons 5 23 to activate automatic seek function Press for several seconds until MANUAL appears on the display the manual tuning mode is selected If both buttons have not been pressed for several seconds they
24. recording some CD Rs CD RWs may not be played on this unit see 1 1 To have more reliable play back please see following recommendations a Use CD RWs with speed 1x to 4x and write with speed 1x to 2x b Use CD Rs with speed 1x to 8x and write with speed 1x to 2x c Do not play a CD RW which has been written for more than 5 times C Notes on MP3 files MP3 Version Only 1 The disc must be in the ISO9660 level 1 2 or level 2 format or Joliet or Romeo in the expansion format 3 When naming a file be sure the file name extension is MP3 4 For a non MP3 file even though the file name extension is the unit cannot recognize it USB PLAY OPERATION In the front panel of the unit there is an USB interface 15 You can connect an USB driver through this interface 15 When you connect an USB driver through the interface the unit will search the MP3 files or WMA files in the USB driver and start to play MP3 files or WMA files automatically If in other mode you can also press MOD button 9 to select USB mode Note e The main unit can only support the standard USB memory disc which is approved by Microsoft e USB player is not a standard which means different brand name or different models have their own standard So our product cannot support every MP3 player e When connecting an MP3 player and there has normal battery in the player non rechargeable battery
25. you should remove the battery from the player then connect it to the USB interface Otherwise it may cause battery burst SD MMC OPERATION OPTIONAL According to the customer s need the unit will add a SD MMC interface See below the SD MMC interface is on the housing of the unit When you insert a SD MMC card in the SD MMC interface the unit will search the MP3 files or WMA files in the card and start to play MP3 files or WMA files automatically The operation is the same with the MP3 operation described above If in other mode you can also press MOD button 1 to elect SD MMC mode CAUTION When there are important files in the USB device or SD card Do not connect it to the main unit to play Because any wrong operation may cause files loss And our company assumes no responsibility for this IPOD operation Select Category When IPOD is playing Press BAND button 3 the category will appear on the display Rotating the volume knob 4 to change the category among PLAY LIST ARTIST ALBUM GENRE SONG COMPOSER then press SEL button 4 to confirm the selected category Select Song Press BAND button 3 the display will show the current catalog Rotating the volume knob 4 to change the song title to the next song or the previous song Then press SEL button 4 to play the selected song PAU Pause When playing a song press button 10 will pause the playing Press it ag
Download Pdf Manuals
Related Search