NX1500E LED KEYPAD SERIES
Contents
1. 7 Master Code Enter the hour code which must be two 2 digits Note The clock is a 24 hour clock Refer to the following table Enter the minutes code which must be two 2 digits Example 7 minutes after would be entered 0 7 Page 16 Time Hour Code Time Hour Code Time Hour Code 12 00 Midniaht 00 8 00 AM 08 4 00 PM 16 1 00 AM 01 9 00 AM 09 5 00 PM 17 2 00 AM 02 10 00 AM 10 6 00 PM 18 3 00 AM 03 11 00 AM 11 7 00 PM 19 4 00 AM 04 12 00 12 8 00 PM 20 Noon 5 00 AM 05 1 00 PM 13 9 00 PM 21 6 00 AM 06 2 00 PM 14 10 00 PM 22 7 00 AM 07 3 00 PM 15 11 00 PM 23 SETTING THE KEYPAD LIGHTING The lighting behind the keypad buttons can be increased or decreased as desired Press the A and VW scroll keys to lighten or darken the illumination behind the buttons It is usually easier to set this adjustment in a darkened room SERVICE MENU The service light will be on if the security system requires service If the service light is on press the key followed by the 2 key to determine the service condition One or more zone lights will illuminate indicating what service s is required Call your service provider immediately for these problems Below is a listing of what each light means in a service condition TO EXIT THE SERVICE LIGHT MODE PRESS THE KEY LIGHT PROBLEM 1 SYSTEM FAULT Press the 1 key The zone light s that is illuminated corresponds to the system2. Step 1 Close all protected doors and windows Step2 e Step 3 e Step 4 e Ready light must be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light The security system will not arm if the ready light is not on or flashing If the power light is off you have no AC power Restore power if possible If not contact your installing company listed on page 1 of this booklet for service Enter your 4 or 6 digit user code If Auto Bypass is enabled all interior zones will be bypassed if you do not leave through a designated entry exit door If Auto Bypass is enabled omit Step 3 When Auto Instant is enabled if you do not leave through a designated entry exit door the instant light will illuminate indicating that the entry exit doors no longer have an entry delay If Auto Instant is enabled omit Step 4 Press the STAY key The stay light will illuminate indicating that all interior zones are bypassed All interior devices will bypass automatically giving the user freedom of movement within the interior area The bypass light will illuminate if any zone s are bypassed If any zone s have been bypassed previously by the user the light s corresponding to the bypassed zone s will illuminate alerting the user that a zone s may be unprotected and can be faulted without an alarm To toggle from a delayed
3. off otherwise EXIT LIGHT The exit light is on during the exit delay Please note that the light will flash during the last 10 seconds of the exit delay as a warning that the time is running out The user may want to disarm the system if the exit light is flashing in order to prevent an alarm The user may then re arm the system and exit before the delay expires FIRE LIGHT A steady fire light means a fire zone has been faulted A rapidly flashing fire light means that a fire zone is in a trouble condition Page 5 INSTANT LIGHT The instant light is on when there is no delay on your entry exit door s Any time the instant light is on and the exit delay has expired the opening of an entry exit door will produce an immediate alarm The instant light can be toggled on or off by pressing the Stay key while the system is armed When the instant light is off the entry exit door s is delayed POWER LIGHT The power light is on if the primary power is on The power light will flash if the system has a low battery condition READY LIGHT The ready light is on when the system is ready to arm and flashes if ready to force arm The ready light is off when the system is not ready to arm because of a zone s being faulted STAY LIGHT The stay light is on when the all interior motion detector zones are bypassed ZONE LIGHT The zone lights are off when everything is normal A zone light will be on if the z
4. USING THE QUICK ARM Optional see page 1 9 CHANGING MODES WHILE SYSTEM IS 9 DISARMING THE SYSTEM 10211 hehehe nhanh nhan nnne nn nan 9 CANCEL ABORT FEATURE Optional see page 1 9 BYPASSING ZONES eterne ERES Rh ENFRENTA NER ENNEN AES 12 GROUP BYPASS eege ee EE cer tement entend 4 nr 12 UNBY PASSING 12 TURNING THE DOOR CHIME ON AND 0 66 nnne 12 ADDING AND CHANGING USER CODES 13 ASSIGNING USER CODE AUTHORITY 65 13 OTHER KEYPAD 5 15 SETTING THE KEYPAD TONE sisi assist or nato io do np nau a yeu Faire ERN 15 VIEW ALARM MEMORY eder tate Ee SEN 15 TEST FUNCTION Optiorial ek EEGENEN ena Ek SNR ENEE NEEN danse 15 RESET FUNCTION perte erronee ten deg denses 16 SETLSYSTEM DATE sine een a peer even ee ne annees 16 SETTING THE SYSTEM CLOCK nnn heres 16 SETTING THE KEYPAD 76777 7 6 17 KEYPAD CONTROL TONES 5 18 EMERGENCY EVACUATION 65 19 Page 3 Abort Delay Authority Level Central Station Chime Feature
5. Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center Check with your installing company to determine how your security system will respond to the Panic Hold Up activation KEYPAD FUNCTIONS ARMING YOUR SYSTEM IN THE AWAY MODE AWAY is used when the user is away from the premise and wants the interior protected Listed below are the steps to arm in the AWAY Mode Step 1 Close all protected doors and windows e Ready light will be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light e The security system will not arm if the ready light is not on or flashing e If the power light is off you have no AC power Restore power if possible If not contact your installing company listed on page 1 of this booklet for service Page 7 Step 2 e Enter your 4 or 6 digit user code to arm the system The armed and exit lights will illuminate e You may now leave the building NOTE The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire The user may wish to disarm and rearm the system if more time is needed ARMING YOUR SYSTEM IN THE STAY MODE STAY is used when the user is inside the premise and wants protection around the perimeter Listed below are the steps to arm in the STAY Mode
6. may not detect heat and smoke in all situations Use qualified security professionals to install and maintain your security system It may be possible to arm the security system without the backup battery connected Your periodic test should be done with AC Power removed to verify the battery is connected and adequately charged Care should be taken to plug in and restrain the AC Transformer after testing Please read the following information and instructions carefully before operating your security control system Page 2 TABLE OF CONTENTS TABLE OF CONTENTS 3 GLOSSARY OF TERMS 4 UNDERSTANDING THE LIGHTS ck 5 ERE en BYPASS LIGHT eek CANCEL LIGH pP CHIME LIGHT EXIT LIGHT iiim e FIRE LIGHT ERR 5 lem rgBIci ppm 6 POWER M BICI p 6 READY PIGH Tz anges Sobre ne hee se ee 6 oii iaeei er 6 LONE LIGHT Em 6 EMERGENCY ACTIVATION 7 KEYPAD 65 7 ARMING YOUR SYSTEM IN THE AWAY MODE 7 ARMING YOUR SYSTEM IN THE STAY MODE 8
7. systems someone changing the code of another person must have access to all or more partitions than the user being changed The ready light will flash Enter the 2 digit user number always enter 2 digit such as 0 3 for user 3 or 5 2 for user 52 The zone lights will illuminate specifying the first digit of the user code Lights 1 8 on code is blank lights 1 8 off 0 lights 1 and 8 9 Use the A scroll keys to view the next digit or enter new 4 or 6 digit user code NOTE While using the A V scroll keys you can change any digit by entering a new digit This will advance you to the next digit To delete a user code enter for a 4 digit code or DE Dk1 D Dk D for a 6 digit code The ready light will flash indicating you are back at Step 2 above If the code is rejected the sounder will beep 3 times If another user code needs to be programmed return to Step 3 Press the key while the ready light is flashing to exit the User Code Programming Mode ASSIGNING USER CODE AUTHORITY LEVELS Assign authority levels to users by following the steps below Assign user codes before assigning authority levels Step 1 NOTE Step 2 Step 3 Step 4 Press 6 Master Arm Disarm Code Someone changing the authority of another person can only add or remove partition authorization for partitions to which they have access The ready light will flas
8. to indicate bypass slow flash for zone fault fast flash for service condition 5 FUNCTION KEYS perform various functions NUMERIC CODE ENTRY KEYS 3 PROGRAMMABLE EMERGENCY ACTIVATION KEYS The door is detachable and can be removed or Service replaced when desired Monitoring The appropriate boxes should be marked on the door of your keypad for the Emergency Activation keys Mem that are programmed to work with your system 19 3 This system is Q isnot partitioned 4 dM Your System is programmed for the functions ee checked below 6 s Fire Emergency Siren Test T 5 Chime Feature Abort Delay 8 16 Group Bypass Re Exit Feature EMERGENCY ACTIVATION KEYS a Aux Emergency da Cancel Alarm Oves Ono vesno Oves Q Quick Arm Q Battery Test Police Emergency Forced Arming Installer Check Activated Functions NOTE Some of the features described above mayor may not be available for your system Check with your installation company to find out how your system is programmed BYPASSING ZONES If you wish to bypass one or more zones this must be done while the system is in the disarmed state The following steps are used for bypassing zones Step 1 Press the BYPASS key Step 2 Enter user code if required optional The bypass light flashes Step 3 Enter 1 or 2 digits indicating the zone you wish to bypass i e press the 1 key fo
9. Codes Duress Code Forced Arming Function Code Group Bypass Instant Delay Master Code Partitioned System Perimeter GLOSSARY OF TERMS An option that allows a delay in reporting to the central station The level of access an individual has when using an alarm panel The location where alarm data is sent during an alarm report An option that allows the keypad to sound a ding dong whenever an entry exit door is opened Can be either User Codes relating to a person or Function Codes a toggle switch to turn specific functions on off NOTE A system may have either 99 four digit codes or 66 six digit codes but not a mixture of the two An option that allows a special code to be sent to the central station that indicates the alarm system is being operated under duress An option that allows the system to be turned on ARMED with one or more zones open A system that is ready to be force armed will flash the ready light Note Those zones that are not ready will not create an alarm A Function Code is either a four 4 or six 6 digit code that has been programmed by the installer to operate a device An option that allows the user to bypass multiple zones with a single operation An option that allows an instant alarm condition for Entry Exit doors or grants a delay to allow someone to enter exit the building without an alarm or before entering a user code to disarm A master arm disarm co
10. NetworX Armed Ready e Instant Power Fire Service Networx Series NX 1500E LED Keypad User Manual SECURITY SYSTEM NOTES Installing Service Company For Service Call Central Station Duress Code FUNCTION CODES Function Code Controls Function This system is isnotQ partitioned EMERGENCY ACTIVATION KEYS check if enabled Q Fire Q Auxiliary Emergency Q Police PROGRAMMED FUNCTIONS Q Abort Delay Q Cancel Alarm Q Forced Arming Q Auto Bypass Q Change Partitions Q Group Bypass Q Auto Instant Chime Q Quick Arm Q Battery Test Q Communicator Test Q Re Exit Q Siren Test ENTRY EXIT DELAY TIMES Exit Delay Time Secondary Exit Delay Time Entry Delay Time Secondary Entry Delay Time ZONE DESCRIPTIONS 01 09 02 10 03 11 04 12 05 13 06 14 07 15 08 16 Page 1 THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION ALL USERS OF YOUR SECURITY SYSTEM SHOULD READ AND FOLLOW THE INSTRUCTIONS AND PRECAUTIONS IN THIS BOOKLET AND IF POSSIBLE PRACTICE ON THE KEYPAD CONTROL WHILE YOUR PROFESSIONAL INSTALLER IS ON SITE FAILURE TO DO SO COULD RESULT IN THE SECURITY SYSTEM NOT WORKING PROPERLY THIS BOOKLET SHOULD BE KEPT IN AN ACCESSIBLE LOCATION FOR THE LIFE OF THE SECURITY SYSTEM IF YOU DO NOT UNDERSTAND ANY PART OF THIS MANUAL YOU SHOULD NOTIFY YOUR INSTALLING COMPANY SH
11. OWN ON PAGE 1 The SECURITY CONTROL can be turned on ARMED and off DISARMED by entering a 4 or 6 digit code into the Keypad Control which is similar to a telephone keypad If your Security Control has been so programmed you may be able to turn on ARM your System by simply pressing the STAY or EXIT key The system must always be disarmed using a 4 or 6 digit code The LED keypad includes up to 35 lights and a built in electronic sounder These provide specific information relating to the status of the security system which is described in the booklet Understanding what the lights and sounds mean will help you to easily operate your system Keep in mind the level of security you will obtain with this system relates specifically with two major factors 1 The quantity quality and placement of security devices attached to this system 2 The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete system You should be aware of the following facts when preparing a safety security plan for your home business Your security system is an electronic device and is subject to failure or malfunction Do not rely on it as your single source of security Your system should be tested weekly Your system will not work without power Warning devices will need to be loud enough wired correctly and properly placed to provide notification of an alarm event Smoke and heat detectors
12. artition 6 7 Partition 7 8 Partition 8 Step 7 When the partitions are assigned press the key This returns you to Step 2 previously mentioned At this point you may enter another user number to assign authority level Repeat Steps 3 7 until you have assigned authority levels to all user numbers Step 8 Press the key to exit the Assigning Authority Level Program Page 14 OTHER KEYPAD FUNCTIONS SETTING THE KEYPAD TONE Step 1 Step 2 Step 3 Press 0 Keypad is now in the Adjust Tone mode Pressing the A key will make the keypad sounder go to higher tones pressing the W key will make the keypad sounder go to lower tones When the desired tone is reached press the key to set this tone and exit from the Adjust Tone mode CHANGE PARTITION Optional Step 1 Press 1 Step2 Press a NUMBER key between 1 and 8 to change partitions momentarily Step 3 If no other key is pressed it will go back to its standard partition in ten seconds Step 4 If another key is pressed the system will remain in the new partition until no keys have been pressed for 60 seconds VIEW ALARM MEMORY Step 1 Press 3 zone s that created the last alarm will be displayed on the keypad Step 2 The ALARM MEMORY feature will flash those zones that created alarms and will light steady those zones that were bypassed during the last alarm TEST FUNCTION Optional If programmed this function will
13. de that can program other user codes A system divided into multiple areas in which its own user or users control each area The outer edge of the protected area Page 4 Quick Arm An option that allows you to turn on ARM the security system by pressing either the STAY or EXIT key on the keypad control for ARMING only as programmed by the installing company User Code A four 4 or six 6 digit entry code used to arm or disarm the system UNDERSTANDING THE LIGHTS ARMED LIGHT The armed light is on when the system is armed The armed light is off when it is disarmed The armed light will flash when there has been an alarm during the previous arm cycle BYPASS LIGHT The bypass light is on when any zone in this keypad s partition is bypassed The zone s that is bypassed will also be illuminated If the bypass light is off no zones are bypassed CANCEL LIGHT The cancel light will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication process Note The abort feature must be enabled Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on until the central station has received the cancel report Note The cancel feature must be enabled CHIME LIGHT The chime light is on when the chime feature is on
14. dy to slam the door if smoke or heat rush in Practice escaping to the outdoors and meeting in an assigned spot Call the Fire Department from a neighbor s phone NOTE After the installation of your Security System has been completed notify your local Fire and Police Departments to give them your name and address for their records Early Page 19 warning fire detection is best achieved by the installation of fire detection equipment in all rooms This equipment should be installed in accordance with the National Fire Protection Association s Standard 72 For additional information write the National Fire Protection Association Batterymarch Park Quincy MA 02269 The following are examples of evacuation plans A plan unique to your home or business should be drawn and memorized by each occupant KITCHEN BATH BEDROOM BEDROOM 4 DINING ROOM PS BEDROOM BEDROOM FIRST FLOOR vv SECOND FLOOR FRONT lt gt Page 20 SYSTEM NOTES Page 21 GE Interlogix NX1500E SERIES USER S MANUAL NX1500EUBO3 REVB MARCH 2003
15. entry mode to an Instant mode press the STAY key again The instant light will illuminate indicating that the entry exit doors have no entry delay Page 8 USING THE QUICK ARM Optional see page 1 The Quick Arm feature may be used if it is enabled Quick Arm will allow the user to arm the security system in the AWAY mode by pressing the EXIT key or arm in the STAY mode by pressing the STAY key This feature is used for ARMING ONLY and will not disarm the security system This is ideal for a maid or baby sitter code etc CHANGING MODES WHILE SYSTEM IS ARMED Pressing the STAY key will turn on off toggle a delay on entry exit doors and turn on off toggle the instant light Optional Press the BYPASS key at this time to turn on off toggle all designated interior zones Optional When armed pressing the EXIT key will start the exit delay enabling you to leave the building IMPORTANT The instant light needs to be off at this time if you plan on re entering the building otherwise you will create an alarm You may restore an entry delay by pressing the STAY key again DISARMING THE SYSTEM When you enter the protected area through one of the designated Entry Exit doors the keypad control will sound a continuous tone for the duration of the entry delay time or until you enter a valid code The red armed light will go off and the tone will stop The security system is now DISARMED If a valid code i
16. fault s below 1 Over Current Fault 5 Expander Low Battery 2 Siren Trouble 6 Expander Box Tamper 3 Box Tamper 7 Expander Trouble 4 Expander Power 8 Ground Fault Note Faults 1 amp 2 are global in nature and will affect all partitions of a multi partition system Press the key to return to the 1 of 8 service lights 2 ZONE TAMPER Press the 2 key and the zone light s will illuminate showing the zone s that are tampered Press the 3 key to return to the 1 of 8 service lights Page 17 3 ZONE LOW BATTERY Press the 3 key The zone light s will illuminate showing which zone s has a low battery This only applies to wireless zones Press the key to return to the 1 of 8 service lights 4 ZONE LOSS OF SUPERVISION Press the 4 key and the zone light s will illuminate showing which 20 5 has loss of supervision This only applies to wireless zones Press key to return to the 1 of 8 service lights 5 ZONE TROUBLE Press the 5 key and the zone light s will illuminate showing which zone s has a trouble condition Press the key to return to the 1 of 8 service lights 6 TELEPHONE LINE TROUBLE LINE CUT Press the 6 key The zone light s will illuminate as they correspond to these service conditions 1 5 Reserved 6 Telephone Line Trouble Line Cut 7 Aux communication device failure The service light will remain lit until the trouble clears and a user code is en
17. h Enter the 2 digit user number to be assigned authority The ready light is constant and the instant light will flash Lights illuminated indicate the authority levels assigned to this code An explanation of the lights is listed in the following table Page 13 You may toggle turn on off the authority level by pressing the number for that authority level LIGHT AUTHORITY LEVELS IF LIGHT 8 IS OFF 1 Reserved Note Do not change if on 2 Arm Only 3 Arm Only After Closing Time 4 Master Arm Disarm can program other codes 5 Arm Disarm 6 Bypass Zones 7 Open Close Reporting 8 If this light is on this code is programmed as a function code Do not change Press to exit Step 5 Press the key The ready light will flash This moves you to the partition enable The user has access in partitions that are illuminated Step 6 illuminated numbers indicate each partition where the user has access To change any of the partitions where the user has access press numbers corresponding to areas where you want to give the user access or deny access Example If zone light 2 is lit then the user is assigned access to partition 2 By pressing the 2 key the light will go off denying access to partition 2 Refer to chart shown below LIGHT PARTITIONS ASSIGNED 1 Partition 1 2 Partition 2 3 Partition 3 4 Partition 4 5 Partition 5 6 P
18. one has been bypassed If a zone light is flashing that zone is in alarm or has been faulted If a zone light is flashing rapidly it means that the zone is in a trouble condition Trouble conditions are Tamper Hardware Low Battery Loss of Supervision A combination of Alarm Fault and Tamper Trouble will produce a rapid flashing light for a short period of time followed by a slow flashing light Page 6 EMERGENCY ACTIVATION KEYS Auxiliary Emergency Police NOTES You must hold these keys for 2 seconds to activate these functions Your system may not be programmed for these activation keys see page 1 You should press these keys only in an emergency situation that requires response by emergency personnel If your system is programmed for these functions the following reports can be sent Fire Key This key can activate the fire alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Auxiliary Emergency Key This key can activate the auxiliary alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Police Panic Hold Up Key This key can sound a local audible alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be transmitted to that center NOTE Some Panic Hold
19. perform a battery test communicator test and or a siren test Alarms and reports will not be sent unless a communicator test is performed at which time a test signal will be sent Step 1 Step 2 Press 4 The test will be performed as programmed If the siren test is performed enter a user code to silence the siren Page 15 RESET FUNCTION This function is used to reset Smoke Detectors Zone Troubles and Zone Tampers Your system must be Disarmed to use the Reset function Step 1 Press 7 Resets have now been performed Step 2 If the keypad begins beeping the reset did not execute properly Enter your code to silence the keypad Wait a few minutes and repeat step 2 to attempt another reset If the keypad still beeps after repeated attempts please contact your installer SET SYSTEM DATE Step 1 Press the 9 6 Master Code Step2 Enter the Day of Week 1 Sunday 3 Tuesday 5 Thursday 7 Saturday 2 Monday 4 Wednesday 6 Friday Step 3 Enter the Month Code Must always be two 2 digits 01 January 05 May 09 September 02 February 06 June 10 October 03 March 07 July 11 November 04 April 08 August 12 December Step 4 Enter the Day Code Must always be two 2 digits Example The 5 would be entered as 0 5 Step 5 Enter the last two digits of the Year Code Example For 1997 enter 9 7 SETTING THE SYSTEM CLOCK Step 1 Step 2 Step 3 Press 9
20. r zone 1 press 1 2 for zone 12 Step 4 Press the BYPASS key again Step 5 corresponding zone light will illuminate indicating the zone has been bypassed Repeat steps 3 and 4 for any other zone s that need to be bypassed Step 6 Press the BYPASS key again or press the key to exit the Bypass Mode The bypass light will stop flashing upon exiting the Bypass Mode GROUP BYPASS By pressing the BYPASS key followed by the 0 key then the BYPASS key again all zones that are designated as group bypass zones will be bypassed Press the BYPASS key again to exit group bypassing UNBYPASSING To manually unbypass zones perform the bypassing procedure on a zone that is already bypassed The corresponding light for that zone will go off when unbypassed NOTE All zones will automatically be unbypassed each time the system is disarmed TURNING THE DOOR CHIME ON AND OFF The door chime is turned on or off by pressing the CHIME key while the system is in the disarmed state If the chime is on the chime light will be illuminated If the chime is off the chime light will be off Each press of the CHIME key will toggle the chime feature on off and produce a momentary ding dong sound Page 12 ADDING AND CHANGING USER CODES Your system must be Disarmed to change user codes Step 1 NOTE Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Press 5 Master Arm Disarm Code For partitioned
21. s not entered before the end of the entry delay an alarm will occur NOTE If the red armed light is flashing during the entry delay the alarm system has been activated in your absence Leave the building immediately and call your alarm company and or the police from a safe location CANCEL ABORT FEATURE Optional see page 1 The cancel light will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication process Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on until the central station has received the cancel report Page 9 NX 1500E LED Keypad includes NX 1508E and NX 1516E ARMED Light is on when armed off when rej rw SE Armed Ready disarmed Flashes to indicate a previous alarm re rw READY Light is on when the system is ready to nee Power arm flashes if ready to lorce arm Fire Service POWER Light is on when AC power is present flashes to indicate a low battery condition INSTANT Light is on when there is no entry delay SERVICE Light is on to indicate a trouble condition with your system Stay Chime Exit Bypass Cancel c qum D a D FIRE Light is on to indicate fire alarm flashes to indicate a trouble condition with your fire system ZONE LIGHTS are on steady
22. tered SEE NOTE 7 FAILURE TO COMMUNICATE This light will illuminate when there is a failure to communicate between your system and the central station SEE NOTE 8 LOSS OF SYSTEM TIME This light will illuminate when there has been a loss of power and your system clock needs to be reset Instructions are on page 16 SEE NOTE NOTE to Lights 6 7 8 This fault is global in nature and will affect all partitions of a multi partition system KEYPAD CONTROL TONES BEEPS A sounder is built into the keypad If programmed your system keypad may sound for any of the following reasons Beeps for all keypresses Sounds a continuous tone during the Entry delay time Pulses when a day zone is violated while the system is disarmed Pulses when a FIRE zone has a trouble condition Beeps 3 times for trying to arm with the Ready light off if Force Arming has not been selected Page 18 Beeps for 1 second or emits a ding dong sound for the Chime feature Beeps during an exit delay beeps rapidly for the last 10 seconds of an exit delay and beeps 1 second at the end of the exit delay Pulses when the armed status changes the power is off Pulses when the armed status changes and any zone s are bypassed Pulses when the armed status changes and a low battery is detected Pulses when the armed status changes and a Tamper condition is detected Beeps
23. to indicate Telephone Line Cut if selected Pulses when one or more of the following conditions are detected Zone or Box Tamper Low Battery AC Power Fail or Expander trouble Entering a valid code will silence the keypad sounder when it is pulsing The arm disarm state of your system will not change when entering a code to silence a pulsing keypad sounder Please contact your installer if a trouble condition exists EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition For example the following steps are recommended by the National Fire Protection Association and can be used as a guide in establishing an evacuation plan for your building Draw up a floor plan of your home Show windows doors stairs and rooftops that can be used for escape Indicate each occupant s escape routes Always keep these routes free from obstruction Determine two means of escape from each room One will be the normal exit from the building The other may be a window that opens easily An escape ladder may have to be located near the window if there is a long drop to the ground below Set a meeting place outdoors for a headcount of the building occupants Practice escape procedures In a home sleep with bedroom door closed this will increase your escape time If you suspect fire test the door for heat If you think it is safe brace your shoulder against the door and open it cautiously Be rea
Download Pdf Manuals
Related Search