Home

Manual

1. User s Manual July 2014 Trademark Acknowledgments All trademarks used in this handbook are registered trademarks of their respective companies Copyright 2014 All Rights Reserved We reserves the right to make corrections modifications enhancements improvements and other changes to its products and services at any time and to discontinue any product or service without notice Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete All products are sold subject to our terms and conditions of sale supplied at the time of order acknowledgment We are not responsible or liable for the resale of its products with statements different from or beyond the specification parameters stated by our company Customers are responsible for their applications using our products To minimize the risks associated with customer applications customers should provide adequate operating safeguards We are under no obligation to provide any further technical support service or product software alteration beyond our representation Our products are not authorized for use in safety critical applications where a failure of our product would cause severe personal injury or death unless officers of the parties have executed an agreement specifically governing such use Reproduction of our information or datasheets with alteration is prohibited We are not responsibl
2. 3 Enable remote log Log server IP address Server Port 0 65535 0 23 Figure 4 8 System Log Tabbed Pane The System Log tabbed pane allows you to see Camera s basic log on another browser page or Remote Log Server Where Remote Log Settings Check Enable remote log selection first and then manual entering IP address amp port setting of Remote Log Server After setups are completed click Save button to apply the settings RP SL721P and RP SL721PF User s Manual 4 2 Network Setup Execution Clicking the Network button will display the following tabbed panes on configuring Camera connection with the network General DDNS Multicast IP Filter Network Network Settings DHCP Fixed IP Address PPPoE Port Settings HTTP Port RTSP Port Figure 4 8 Network Setup Tabbed Panes 4 2 1 General Tab The General tabbed pane shown above allows you to redefine the network and port protocol settings of the Network Camera Where Network Settings DHCP This option obtains the available dynamic IP address assigned by the DHCP server each time the Camera is connected to the network Fixed IP Address This option manually assigns a static IP address to the Network Camera RP SL721P and RP SL721PF User s Manual Save PPPoE Select this option to set PPPoE account amp password PPPoE PPPoE User Name PPPoE Password Recipient E mail Address rcpt mail co
3. a 5D card Figure 4 26 Snapshot Recording with Schedule Method Selected RP SL721P and RP SL721PF User s Manual B Motion This method will trigger the Camera snapshot operation according to the set time interval in seconds whenever motion 1s detected within the defined days of the week and at the time of the set days Single or 6 snapshots may be captured as defined The stream of accumulated snapshots may be sent to host by E mail FTP stored in the SD card Remote Disk as preferred or through all of them Motion Video Event Alarm Settings by Snapshot Please note that there is no SD Card plugged in camera or the SD Card is not writable W Snapshot Trigger by Motion Link to Motion Settings IM Only during Day i Sun MON Tue WED gg Thu d FRI gf Sat Time Start oo v 00 v hh mm End 24 v oo v hh mm Snapshot Type Interval 3 minimum is 3 seconds OQ single snapshot s snapshot with 1 second interval 3 frames before and 3 frames after motion frame Target to La E mail User could select Single or 6 snapshot 3FTP SD card Figure 4 27 Snapshot Recording with Motion Method Selected RP SL721P and RP SL721PF User s Manual B GPIO Input On the defined days of the week and at certain time of the set days the Camera will trigger its GPIO Input Signal according to the set time interval in seconds when its state changes Single or 6 snapshots may be
4. J Feed discovery Windows Update Performance dashboard Ctrl Shift U e control properly F12 Developer Tools download video control Internet options RP SL721P and RP SL721PF User s Manual Compatibility View Settings Fe Change Compatibility View Settings Add this website Websites you ve added to Compatibility View Display intranet sites in Compatibility View Use Microsoft compatibility lists Learn more by reading the Internet Explorer privacy statement After successful adding camera webpage should be set as compatible view website Compatibility View Settings P Change Compatibility View Settings Add this website Websites you ve added to Compafibili 192 168 33 198 F Display intranet sites in Compatibility View Use Microsoft compatibility lists Learn more by reading the Internet Explorer privacy statement RP SL721P and RP SL721PF User s Manual Then camera webpage would be refreshing real time and starting to load camera webpage Click Allow button to enable NetcamViewer component running J nttp 192168 33198 D Network Camera 192 1683 X File Edit View Favorites METS This webpage wants to run the following add on J ma NetcamViewer ActiveX Control from egy CORPORATION What s the risk Manual entering camera s username password to pass authentication DJ hitp 192 168 33 198 D C
5. Playback of the stored videos or snapshots is performed from files recorded on particular date range as explained in the following figure Local Storage EIL iui coe Searching and viewing the records Type 1 Select type of files to playback Trigger time 2 Search for the files to playback by defining the files recording date range C 3 Click Search button and the files recorded within the Search results date range will display below amp 20130128 a O 220130128 1945 4 Select the file to playback and enable e O 2013012819 the corresponding check box The M amp 20130128_1860 E 20 dialog strip below will then pops up M 20130128 1860 20130128185250 avi Mamea erte NEF 320130128 1760 O C320130128 1745 320130128 1730 3 ia m D n 1 Do you want to open or save 20130128185250 avi 223 KB from 192 168 1 170 Open Save I cancel x m 5 Clicking Open button will playback the IN file Save button will save file to a designated folder Figure 4 31 Playback Tabbed Panel RP SL721P and RP SL721PF User s Manual o9 Appendix 5 1 Firmware Upgrade This section mainly will instruct you how to update camera firmware step by step 1 Find the camera and open its Web based UI via CamFinder utility Chapter 2 2 X Below are the tips to let you understand how to solve NetcamViewer installation problems more easily gt If below picture is al
6. Time Zone Select the applicable Time Zone of your city in reference to Greenwich Mean Time Automatic Select this item if you want to automatically synchronize the Camera clock with your manually entered Network Time Protocol NTP Server RP SL721P and RP SL721PF User s Manual This is a permanent default setting and cannot be removed nor changed Hence new User Name Group Keep current date and time setting Select this option in lieu of automatic synchronization if the Camera is not connected to NTP Server and uses its own embedded clock Set Manually Synchronize with the computer Time Select this option to manually synchronize the Network Camera clock date and time with that of the local host computer Assign value Select this option to enter the date and time manually Enable Daylight Saving Select this option only when applicable at your location Two setup settings the Start time and End time are needed to implement the feature Save After setups are completed click Save button to apply the settings 4 1 3 Security Tab Information Time Maintenance System Log Security User List settings are only added User Name below the default setting security setting status Click Add button to access and change the Add Figure 4 5 Security Tabbed Pane The Security tabbed pane allows you to add new Camera User Name and change Password and the surveillance status or User Group Cli
7. 20 Save Filling the IP range then click Save button to implement the settings A Ifyou would like to re open the access right of those listed device select it from the list and then click Remove button to apply the settings RP SL721P and RP SL721PF User s Manual 4 3 Video amp Audio Setup Execution Clicking the Video amp Audio button will display the following tabbed Video amp Audio panes for defining Camera streaming video and audio functions C v Audio Privacy Mask Video quality settings for stream 1 Connection template Mode Frame Size Maximum Frame Rate Streaming Mode Bit Rate Intra frame period i Text Overlay Text Field iy Time Stamp RTSP Port Access Name Customized ia H264 Y 18251920 15 v FPS 15v livet sdp Video quality settings for stream 2 Connection template Mode Frame Size Maximum Frame Rate Streaming Mode Bit Rate Intra frame period iy Text Overlay Text Field i Time Stamp RTSP Port Access Name Customized v H264 v 1600x1200 v 15 v FPS 2 Mbps v CH2 live2 sdp Video quality settings for stream 3 Connection template Mode Frame Size Maximum Frame Rate Streaming Mode Bit Rate Intra frame period iM Text Overlay Text Field iy Time Stamp RTSP Port Access Name customized nasa aoras TV 15 FPS car live3 sdp Figure 4 11 Vid
8. Audio In signal Volume Plug an audio source device into the Audio In port of camera And its playback volume could be adjusted by moving the slider to the left to decrease and to the right to increase the volume After setups are completed click Save button to implement the settings 4 3 4 Privacy Mask Tab Stream Video Audio Privacy Mask ROI 3 Enable the check box Enable privacy mask This is an Ellipse type 2 Lay out masking screens on the areas to be blocked from surveillance 1 Select a masking shape to block the private area you wish to surveillance C2 cC 4 Click Save button Figure 4 16 Privacy Mask Tabbed Pane RP SL721P and RP SL721PF User s Manual Delete Save RP SL721P The Privacy Mask tabbed pane allows you to mask or block private areas from surveillance for privacy reason B To block a private area from surveillance follow the procedure below 1 Initially select the masking shape e g Line Rectangle or Ellipse see figure above you wish to use as screen to block the area from surveillance 2 Click and drag the mouse cursor to lay out a masking screen on the area you wish to block and then release the mouse right button Notice that the laid out screen turns into phantom block 3 If the laid out screen needs correction click Delete button and redo the masking screen lay out process 4 Once the masking screen is ac
9. EU GF EC Aa AA D ActiveX control version 0 0 6 8 Wired network Status Connected Mode STATIC IP Address 192 168 2 100 Subnet Mask 255 255 255 0 Gateway 0 0 0 0 Primary DNS 192 168 0 6 Secondary DNS 192 168 0 5 DDNS Server Status No connection Figure 4 3 Information Tabbed Pane The Information tabbed pane provides the existing system status of the Camera which includes Model Name System Time Firmware Version MAC Address ActiveX Control Version Wired Network Wireless Network and DDNS Server Status RP SL721P and RP SL721PF User s Manual 4 1 2 Time Tab Information Security Maintenance System Log System Time 2013 12 26 09 25 51 System Time settings Time Zone GMT 08 00 Beijing Chongqing Hong Kong Kuala Lumpur Singapore Taipei Krasnoyarsk v Automatic NTP server time stdtime gov tw Keep current date and time Set Manually Synchronize with computer time Date 2013 12 26 Time 09 25 51 Assign value Date 2013 12 26 yyyy mm dd Time o9 24 59 hh mm ss i Enable Daylight Saving Offset Day of week Start time sunday End time sunday Figure 4 4 Time Tabbed Pane The Time tabbed pane is where you set up the clock of your Camera to synchronize with your local time Where System Time The Network Camera current date and time is applied and displayed here based on the setup status of the System Time Settings as detailed below
10. scenario There are four kinds of template to choose General Outdoor WDR Night Speed Mode Brightness The luminance of the captured image apart from its hue or saturation Try to assign the fit value according to the environment GN NSII 1505 Saturation The degree of intensity and purity of a specific color Try to assign the fit value according to the environment RP SL721P and RP SL721PF User s Manual Contrast The brightness ratio of the lightest to the darkest part of the video image Try to assign the fit value according to the environment Sharpness Sharpness can be defined as edge contrast 5o when we increase sharpness we increase the contrast only along near edges Try to assign the fit value according to the environment RP SL721P and RP SL721PF User s Manual EV Compensation Exposure Compensation is a feature of a camera that allows you to adjust the exposure value manually You may increase or decrease the amount of brightness or darkness of your picture through sliding the bar Try to assign the fit value according to the environment Pre Noise Reduction amp 2D Noise Reduction Both of them are one kind of technology to provide clearer video with less noise under poor lighting conditions making it easier to identify people or objects Try to set them according to the stream quality RP SL721P and RP SL721PF User s Manual Wide Dynamic Range Enable this function could let cam
11. 0 0 0 192 1660 6 1a 168 0 5 0000 zl Device Search Batch Device Setting Single Device Setting Figure 2 3 Open the Camera s Property setting page via Single Device Setting item RP SL721P and RP SL721PF User s Manual 7 e Installation and Setup Chapter 2 4 Check Static IP address or Use DHCP Service item to select the network connection method of the camera ic Property Device Setting MACAddriess ED SE EC A A A A A oet Certification 09 10 0102 Use Custom Username MW Static IP address me IP Address 182 168 13 24 Subnethask 255 255 255 DHCP Use DHCP Service Gateway 122 158 13 1 Http Fort ou DNs 1 122 158 13 1 DHS 0 0 80 0 DNS3 0 0 80 0 Figure 2 4 Enter the Camera Device s network setting manually 9 Property Device setting set Ha Address F0 8F EC AA AA AA Firmware 1 3 10 0102 Certification C Use Custom Property Use Static IP address e IP Address 192 168 13 24 Subnethlask Am sg EU 0 Gateway ER eee 1 Http Port e DNs 1 HERE lon c c des DNS2 um 0 DNs et 0 Status Figure 2 5 Check Use DHCP Service item to let camera get IP Address automatically 8 e Installation and Setup RP SL721P and RP SL721PF User s Manual Chapter 2 5 After modifying the camera properties click Set button to save and enable the configuration modifications Property Device betting MAC Address FQ 8F
12. Customized Mode H264 v Frame Size 1920x1920 v Maximum Frame Rate 15 FPS Streaming Mode CBR Bit Rate 6 Mbps Intra frame period 15 W Text Overlay Text Field I Time Stamp RTSP Port Access Name live1 sdp After setups are completed click Save button to implement the settings RP SL721P and RP SL721PF User s Manual 4 3 2 Video Tab Setup amp traam video Audio Privacy MaBk ROI Live View System Hetwark es Event Local Moraga Video Settings Templos a pw Bright rizam ML IND 0200 Zriurnmi cm i n me 200 Tairzsl 1go e200 Sherpecas nn ees ame mo 2m0 Color Mone Moiz suz teler LF Mena Dey Night T ezahizls A an maron ICR suis Gon Gor IR LED auc on Qnm Expcmurz Luck suin C Lek zhulTcr Spend w zu v accu n 5 1nnn 12nnc c LL mal Fee FrrcuEncy Cz uz Bare Ew CmmprmsDmen zc znnj B20 fees Seduction Hermal Siron Aula IEIS e Chor White Ealanzz Pute r Wes Orense a liz ii Hinr Figure 4 13 Video Tabbed Pane RP SL721P and RP SL721PF User s Manual The Video tabbed pane lets you to perform live adjustments and improvement of the Camera captured video effect relative to the target environment Where Template That means you can select what environment to use for base on your
13. Information System Model Name RP SL721P Network System Time 2014 07 02 16 01 58 Video amp Audio Firmware Version B0 9 9 0610 Event MAC Address EO 8F EC 44 44 44 ActiveX control version 0 0 7 2 Local Storage Wired network Status Connected Mode DHCP 4 order to have the best performance with Camera kindly please ask for distributor dealer s help to get the latest firmware version downloading 5 After downloading it click the Browse button to open below dialog for firmware choosing Setup Information Time Security System Log Live View Model Name RP SL721PF System f Firmware Version B0 9 9_0610 Network Upgrade Firmware Video amp Audio Select firmware file Event Local Storage E 22 shez OO Firmware p IP Camera p PL721 see Y HERNA A w S RP SL721PF 0310 E xt RP SL721PF 0320 d 5x RP SL721PF 0410 n amp RP SL721PF 0428 am BH RP SL721PF 0505 RP SL721PF 0520 RP SL721PF 0610 Select the appropriate firmware file from its folder in PC and then click Open button to choose it RP SL721P and RP SL721PF User s Manual Setup Information Time Security System Log Live View System Firmware Version B0 9 9 0610 Network Model Name RP SL721PF Upgrade Firmware Video amp Audio Event Local Storage Upgrade X Please specify the correct firmware version mapped with your camera to upgrade or there
14. Quality 4 00 10 30 Low High Figure 4 18 1 Defining multiple ROI Areas for the Camera 4 4 Event Setup Execution Clicking the Event button will display the tabbed panes see figure below for defining event recording of the Camera The RP SL721P and RP SL721PF 1s equipped with a card slot for Micro SD SDHC memory card This storage card 1s utilized to store recording of local video and still JPEG images taken in response to set events The recording operation of events is triggered according to the defined schedules 4 4 1 Motion Tab From the Motion tabbed pane you can define specific target areas within the scope of surveillance to focus the motion detection function RP SL721P and RP SL721PF User s Manual Motion Video Snapshot Motion Setting 1 To enable Motion Detection function W Enable Motion Detection GHI 2014 03 05 14 07 38 Figure 4 19 Defining a Single Motion Detection Area for the Camera B Defining a single motion detection area 1 Enable the Enable Motion Detection check box 2 Click Add button and a default frame will pop up on the screen 3 Click and hold inside the frame to drag it to the location where you want to focus detection Resize the frame by dragging its corners or borders 4 Click the Save button to apply RP SL721P and RP SL721PF User s Manual B Defining multiple motion detection areas 1 After satisfactory positioning of the first detect
15. R HMI _Annliratinn host Show processes from all users Processes 129 CPU Usage 30 Physical Memory 71 RP SL721P and RP SL721PF User s Manual During NetcamViewer installation you may see below prompt windows are always popped This will mainly remind you to close all running browser applications and then press OK button to continue Netcam Viewer installation Or these two windows will pop continuously until all browsers are closed NetcamViewer 1 0 14 0523 Setup Your browser chrome firefox iexplore or safari is already running Please close it before pressing OK to continue when installing MetcamViewer 1 0 14 0523 Setup WARRING Presse YES to close browser and install application or NO gt to finish installing RP SL721P and RP SL721PF User s Manual l Manual input username admin password admin to pass login authentication of camera webpage 2 After Live View page is entering successfully find the SETUP button Clicking it could change or update more Camera settings Page 18 Live View 3 Actual Size 2048x1536 Protocol TOP Video Stream n Recording Path Recording file name Snapshot Path Snapshot file name Browse Setting Language RP SL721P and RP SL721PF User s Manual 3 Find Maintenance Tab of Camera Setup Webpage Chapter 4 1 4 Setup Time Security System Log Live View System
16. Server 192 168 1 1 ex ftp domain com or 192 168 1 1 FTP Server Port 21 0 65535 User Name guest Password ecco Path ftp upload ex ftp upload ed elici ent icc ewenr Make sure the FTP folder load mode if you are not sure then ask the FTP Interval 30 1023600 Seconds software technical support 3 SD card Figure 4 29 Transmitting Snapshots to Host Setup with E mail amp FTP Selected X As for the settings of SMTP Service kindly please contact with your E mail service provider After you confirm all parameters are correct and working properly you may enter them into the text area manually X As for the settings of FTP Service kindly please contact with your FTP service provider While all parameters filled in Windows FTP Transferring Utility are correct and working properly under your Laptop or other PC you may enter them into the text area manually RP SL721P and RP SL721PF User s Manual 4 5 Local Storage Setup Execution l Clicking the Local Storage button will display the following tabbed Local Storage panes to provide information on existing local storage such as disk size info type and status If recording is in progress when clicking the Local Storage button a warning message will occur NOTE Do NOT remove the micro SD card while Camera is in recording process 4 5 1 Local Storage Tab The Local Storage tabbed pane displays the SD card status It shows the S
17. This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name Password I Remember my credentials re Figure 3 1 Windows Security Dialog RP SL721P and RP SL721PF User s Manual Camera Live View UI Settings e 13 3 The Live View Setting window will then display offering all the necessary set up tools for changing the live view reconfigurations The functions of each of these tools are explained in the following sections Live View 3 Actual Size 2048x1536 GH4 2014 02 24 11 45 41 y Protocol TCP v Video Stream p N Recording Path PT Recording file name E Em Snapshot Path Uk m WT uM Wy TUA WS Wi n j il J qm 7 a n V MAT a Snapshot file name Tus AE m ET zm m SO i E E ENTIS a f j DR a ts b Ene RS x m hw Ay e v Browse Setting Language English vl Q p ux PLE S 5 800x600 Double click on video screen to full screen Figure 3 2 Camera Live View Setting Window Chapter 3 3 1 Quick Access Buttons The following buttons provide the basic interactive functions between the Camera and the host computer as described below C 800x800 Double click on video screen to full screen Click on video screen to start PT Figure 3 3 Camera Quick Access Toolbar Buttons
18. Turn On Off the host computer speaker Click this button to enable disable talk function to someone facing the network Camera from your computer For ideal voice reception the distance of the person on view should be kept within 2 meters from the Camera Snapshot Click this button to capture still images taken from the Camera and save them in the host computer Recording Click this button to record live video clips from the Camera into your computer Digital Zoom Digital zoom in amp zoom out of a particular area of the live view To display the whole live view into full screen double click on the video RP SL721P and RP SL721PF User s Manual Camera Live View UI Settings e 15 3 2 Camera Live View UI Setting Tools Actual Size Click actual size to view actual size of Image Protocol Option for TCP UDP or HTTP transmission protocol with H 264 MPEG4 streaming is available Video Stream Two simultaneous streaming is supported for live viewing NUES Click Browse button to define Recording Path and ecording Path CAllsersipignigDesKionl Recording Filename for the video you are preparing to Recording file name record 20130124 gt Recording Path Specify a storage destination path for the video you are going to record Recording file name Define a base filename for the video recordings you are going to take The base filename will auto expand for each saved video recording To start recordi
19. WED i Thu i FRI iy Sat Time Start oo v oo v hh mm End 24 v oo v thh mm Video Clip Type Post event recording 60 v Seconds Target to SD card Figure 4 22 Video Recording with Schedule Method Selected RP SL721P and RP SL721PF User s Manual B Motion This method will trigger the Camera video surveillance recording operation according to the set duration in seconds whenever motion is detected within the defined days of the week and at the time of the set days The video record may be provided to host by E mail FTP stored in the SD card Remote Disk as selected or through all of them Motion Video Snapshot Event Alarm Settings by Video Please note that there is no SD Card plugged in camera or the SD Card is not writable iv Video Clip Trigger by Motion Y Link to Motion Settings iv Only during Day i Sun jg MON iz Tue M WED amp Thu I FRI amp Sat Start oo vj oo v hh mm End 24 vl oo T hh mm Video Clip Type Time Pre event recording 5 Seconds Post event recording 10 v Seconds Target to 3 E mail FTP 3 SD card Figure 4 23 Video Recording with Motion Method Selected RP SL721P and RP SL721PF User s Manual B GPIO Input On the defined days of the week and at certain time of the set days the Camera will trigger its GPIO Input Signal when its state changes Recording duration can be set in seconds and the video record may be provided to host by E m
20. amp Network Camera 192168 3 X File Edit View Favorites Tools Help The server 192 168 33 198 is asking for your user name and password The server reports that it is from IP Camera Warning Your user name and password will be sent using basic authentication on a connection that isn t secure User name Password Remember my credentials RP SL721P and RP SL721PF User s Manual Camera live stream is successful playing in IE11 Browser CH1 2014 04 03 08 45 02 Live View 3 Actual Size 1920x1080 Protocol TCP Video Stream 1 v Recording Path Recording file name Snapshot Path CAUsers Acer Aspire4750GDesktopt Snapshot file name 737 wdr Setting Language ma O 9000 Double click on video screen to full screen If error message opening file for writing C Windows sytem32 LibPMD dll is always popped during NetcamViewer installation kindly please turn of all browser windows include CDWizard application and then try Netcam Viewer installation again So before Netcam Viewer installation please make sure there s no iexplore process running in Windows Task Manager Window If there is ie explore process existing select End Process to force its stop File Options View Help HControl exe 32 HControlUser exe 32 mdm exe 32 mDNSResponder exe 2 060K Bonjour Service mshta exe 32 Liser 1R 76AK__Mirrnsnft
21. below steps to replace Web UI Logo with it RP SL721P and RP SL721PF User s Manual Cc Upload Setting Reboot System Restore System Factory Default 1 Click the Browse button to access and select the Logo Image file from the PC 2 Click the Upload button to process Logo replacing When upload process 1s completed it s strongly recommended to close and restart Web Browser Clicking the Backup button allows you to manually save Camera s parameters and user settings into a file This function allows user to restore Camera s backup setting by executing the below steps 1 Click the Browse button to access and select saved file from the PC 2 Click the Restore button to process Camera configuration restore Clicking the Reboot button allows you to manually reboot the Network Camera Clicking the Factory Default button will restore the Network Camera to its factory default settings status Before Camera system proceed to restore step there ll be a dialog window popped and then ask 1f you would like to keep Network setting parameters Besides all configured data in the System Time Security and Maintenance tab will be remained current RP SL721P and RP SL721PF User s Manual 4 1 5 System Log Tab Information Time Security Maintenance System Log System Log Logs Click it There will be another browser page Remote Log Settings opening and then displaying Camera s basic log
22. n EEE E UR eE 26 wad T T a E E A 26 kar PONS TI E E NAER E E EA AEE E 28 a PS Na M Eze NRI 20 2 221 WP TC WA oats A E 30 43 Videos Audio Setup EXeCULDOD uita eec biebas dao repu sea bob bud REEE sud bob de des aiiu oude 3l eM URC Dea 32 Po NVO CDe E E E A 34 dooa AUO laD err E E E E E 44 Poa PaM k Da xe occi Postato l bhsrate ueni ecd bhslqte Ri vut abu Pate Ru eUS 44 2S EMEN OIN e U 46 Ad Byentoelup EXeOULIOD qnem titoe sid odo E dE b U read TIRE CU EE Und 47 a MEE oio Wc cc sosceotstentseuap E E E E E 47 Be VIGCO MAD 50 LE SMAPS MOL LAD E 54 4 LocalStorage Setup EXC CU IOI oosere dunt eus cond ni Eai a a rE E EA AE i 59 kal OCA torne T E N EE N 39 Revision History iV TOMA ACK TiD S 60 5 Appendix 58 67 5 1 Firmware upgrade Revision History Date Doc Version Revision Description Initial Official Release 2014 04 9 Add Chapter 5 Appendix 2014 07 2 RP SL721P and RP SL721PF User s Manual Read Me First Read Me First Important Notes This User Manual is intended for administrators and users of the RP SL721P and RP SL721PF IR Bullet Network Camera including instructions for using and managing the camera on your network The use of surveillance devices may be prohibited by law in your country or area It is therefore the user s responsibility to ensure that the operation of such devices 1s legal before ins
23. re login again e about blank p v e Blank Page RP SL721P and RP SL721PF User s Manual 11 After camera Web based UI is re login successfully go to Information Tab of Camera Setup Webpage to check if the firmware version is different with before or check if the firmware version is the same with distributor dealer provided Chapter 4 1 1 Setup Time Security Maintenance System Log Live View ze U Model Name RP SL721PF Network System Time 2014 07 02 16 10 37 Video amp Audio Firmware Version B0 9 9 0610 Event MAC Address E0 8F EC AA AA A ActiveX control version 0 0 7 2 Local Storage Wired network RP SL721P and RP SL721PF User s Manual
24. will be danger to damage camera system 6 Click the Upgrade button and then one prompt window will pop to tell you wait about 30 seconds to stop all processes A Please waiting about 30 seconds to stop all processes 7 Click the OK button to exit the window Then you will see Camera Webpage is reloading it means all processes of camera are stopping at the same time RP SL721P and RP SL721PF User s Manual 8 After all processes are stopped the camera will start to upgrade the firmware you chose Firmware Upgrade It is strongly recommended to stop any unnecessary jobs while updating firmware Please be patient and the updating process may take a long time Please waiting about seven minutes Writing Progress S O Until the process goes to 100 there will be messages popped to suggest you restart the Web Browser e http 192 168 13 10 p e Network Camera 192 1681 Firmware Upgrade It 1s strongly recommended to stop any unnecessary jobs while updating firmware Please be patient and the updating process may take a long time Please waiting about seven minutes ffiting Progress Firmware upgrade complete It is strongly recommended to close and restart the Web Browser 10 While the button 1s clicked the camera webpage connection will be closed Message from webpage Connection is closed Please close the message window and restart the browser And then you have to
25. D card total capacity Total size available memory Free size used memory Used size and used memory ratio Use It also display the current Camera operation condition Recording status and provide SD card control option where user can select to allow the Camera to auto overwrite earlier files in order to maintain the defined Keep Free Space memory size Local Storage Playback SD card management SD card status OK Total size 15756768 KBytes Free size 13913392 KBytes Used size 1843376 KBytes Use 12 Enable check box to Recording status Not Recording allow auto overwrite D card control of earlier files in order to maintain the defined Keep Free eep Free Space 64 MB 30 500 MB Space memory size Please stop all the events related to the SD card recording before ejecting or formatting the SD card co co Figure 4 30 Local Storage Tabbed Pane iv Enable cyclic storage Click this button to save changes to the SD card control setting Click this button to format the SD memory card take note of the message in red Click this button to refresh the SD card information RP SL721P and RP SL721PF User s Manual 4 5 2 Playback Tab The Playback tabbed pane allows user to playback video and snapshot files stored in the SD memory card These files were saved using the Event setup for video see Section 4 4 2 and snapshots Section 4 4 3 with the SD card check box enabled
26. EL Event Alarm 5ettings by 5napshot Please note that there is no SD Card plugged in camera ar the SD Card is not writable W Snapshot Trigger by Always ww Snapshot Type 6 snapshot with p v econd interval 3 frames before and 3 frames after motion frame Target to ua 6 snapshots are continuously E mail collected at every 1 or 2 seconds interval Ga FTP 3 SD card Figure 4 25 Snapshot Recording with Always Method Selected RP SL721P and RP SL721PF User s Manual B Schedule This method activates the Camera snapshot operation continuously when the defined days of the week and set time of the set days are met The Camera will continuously capture 6 snapshots of the area under surveillance at every 1 or 2 seconds interval 3 previous snapshot frames are collected from the Camera buffer and 3 snapshot frames are captured live The stream of accumulated snapshots may be sent to host by E mail FTP stored in the SD card Remote Disk as preferred or through all of them Motion Video Snapshot Event Alarm Settings by Snapshot Please note that there is no SD Card plugged in camera or the SD Card is not writable W Snapshot Trigger by Schedule v Day iM Sun MON iM Tue y WED iM Thu M FRI M Sat et Start oo oo w thh mm End 24 v oo hhimm Snapshot Type Tim s snapshot with 1 second interval 3 frames before and 3 frames after motion frame Target to 34 E mail a FTP
27. FC 34 48 84 Certification Firmware 09 10 0102 Use Custom Property M static IP address PM IP Address 192 168 13 34 SubnetMask 255 255 255 0 DHCP Use DHCP Service Gateway 192 188 13 1 E Http Port B DNS1 192 168 13 1 DNS2 0 0 0 DHSS 0 0 0 Figure 2 6 Click Set button to save and enable the modification RP SL721P and RP SL721PF User s Manual 9 e Installation and Setup Chapter 2 6 Use Ctrl or Shift key on the keyboard to choose several Camera Devices Then click the Batch Device Setting to configure them together RP SL721PF IP Address 192 1698 2 100 MACAddress E0 8F EC 44 44 44 099 519 62 192 1608 13 004 E0 8F EC BB BB BB 09 10 _0102 92 168 13 008 E0 8F EC DD DD DD 0 9 10_0102 EO 8F EC EE EE EE 09 10 0102 255 255 255 0 255 255 255 0 192168131 0000 EE 255 192 168 13 1 192 168 13 1 00 00 RP SL721PF RP SL721PF EU 8F EC FF FF FF 0 9 10 0102 E0 8F EC HH HH RP SL721PF RP SL721PF RP SL721PF RP SL721PF RP SL721PF RP SL721PF RP SL721PF Propertv IP Address eubnetMask Gateway Http Fort DN51 DNS2 DNS ECSEECILILI Batch Device Setting gt _ E0 8F EC I J Single Device Setting Open web Language EO 8F EC 11 11 11 E0 8F EC 22 22 22 0 9 10 0102 192 168 13 031 192 168 13 032 0 9 10_0102 0 9 10 0102 E0 8F EC 33 33 33 EO 8F EC 44 44 44 Figure 2 7 Select multi Camera Devices and then configure
28. ail FTP stored in the SD card Remote Disk activated GPIO Output Port or through all of them Motion Snapshot Event Alarm Settings by Video Please note that there is no SD Card plugged in camera or the SD Card is not writable iM Video Clip Trigger by GPIO Input v Trigger Pattern Low to High v IM Only during Day M Sun M MON iM Tue M WED iM Thu M FRI M Sat Start 00 v 00 v hh mm End 24 w 00 v hh mm Video Clip Type Time Pre event recording 5 Seconds Post event recording 5 v Seconds Target to 34 E mail FTP 2 SD card 3 GPIO Output 1 Figure 4 24 Video Recording with GPIO Input Method Selected RP SL721P and RP SL721PF User s Manual 4 4 3 Snapshot Tab The Snapshot tabbed pane sets the Camera to take snapshot images when motion is detected The four methods available for selection are Always Schedule Motion and GPIO Input each of which can be set up with user scheduled recoding time and duration as well as defining the video record file target destination B Always Under this method the Camera automatically continuous to capture 6 snapshots of the area under surveillance at every 1 or 2 seconds interval 3 previous snapshot frames are collected from the Camera buffer and 3 snapshot frames are captured live The stream of accumulated snapshots may be sent to host by E mail FTP stored in the SD card Remote Disk as preferred or through all of them Motion Video
29. as they are needed to view the video stream and some other operations Besides use of Microsoft IE browser is recommended as it offers a better compatibility p I D Windows Security E i The server 192 168 245 at IP Camera requires a usemame and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection This webpage wants to run the following add on FAS NetcamViewer ActiveX Control Figure 2 11 ActiveX components are required for Camera s Live Stream and configuration operation RP SL721P and RP SL721PF User s Manual 11 e Installation and Setup Chapter 2 3 If the camera and browser components have been configured correctly the default Web browser will open to the Live View page of the selected camera CH1 2014 04 03 09 45 02 Live View f Actual Size 1920x1080 Protocol me v Video Stream a M Recording Path Recording file name Browse Snapshot Path CAUsers Acer Aspire4750G Desktop Snapshot file name 737 war Browse Setting Language ma CQ S O Q 800x450 Double click on video screen to full screen Username and password is required to enter SETUP Webpage Default 1s admin admin Verify and Complete the Installation from Your Browser If your IE Browser can t get the ActiveX download properly you may have to tempora
30. captured at a time as defined Motion Video Snapshot Event Alarm Settings by Snapshot Please note that there is no SD Card plugged in camera or the SD Card is not writable if Snapshot Trigger by GPIO Input Trigger Pattern W Only during Day E Sun y MON f Tue y WED E Thu i FRI pf Sat Start 00 t oo hhimm End 24 v oo hhimm Snapshot Type Time Interval 3 minimum is 3 seconds Single snapshot O 6 snapshot with 1 second interval 3 frames before and 3 frames after motion frame Target to H E mail E FTP 3 5D card 2 GPIO Output 1 Figure 4 28 Snapshot Recording with GPIO Input Method Selected The stream of accumulated snapshots may be sent to host through E mail FTP stored in the SD card Remote Disk activated GPIO Output Port per selection or through all of them When selected the setup dialog for these methods will display is illustrated in the following figure RP SL721P and RP SL721PF User s Manual Target to iy E mail Recipient E mail Address rcpt mail com ex rcpt mail com SMTP E mail Server 192 168 1 1 ex mail examples com or 192 168 1 1 Port 25 0 65535 User Name guest Password eocce Sender E mail Address from mail com ex from mail com Interval 30 30 3600 Seconds Use SSL TLS None v None Here refers the mailbox encryption mode if you are SA FTP SSL TLS unsure ask your mailbox customer service staff STARTTLS FTP
31. ceptable click the Enable Privacy Mask check box followed by clicking of the Save button This will turn the laid out screen into solid block B To disable masking and remove the screen do the following 1 Click Delete button 2 Click Save button and wait a while Then the screen is permanently removed Stream Video Audio Privacy Mask ROI 3 Enable privacy mask CHT 2014 03 05 14 03 34 2 Then click the Save button and wait the state finished Figure 4 17 Removing Privacy Mask Screen from Camera 3 To permanently disable the Privacy Mask function disable the Enable Privacy Mask check box and RP SL721PF User s Manual 4 3 5 ROI Tab When network capacity is constrained or there is simply a desire to improve network usage efficiency and storage clicking the ROI button will display the tabbed panes see figure below for defining enhance video quality area of the camera B Defining a single ROI detection area 1 Enable the Enable check box 2 Click Add button and a default frame will pop up on the screen 3 Click and hold inside the frame to drag it to the location where you want to focus detection Resize the frame by dragging its corners or borders 4 Click the Save button to apply X only support H 264 1 To enable ROI function Stream ROI Setting Video Stream 2 To draw a region to define the detection range Set New ROI Area 1 Click Add to create the wi
32. ck the Add button to access the security setup dialog shown below RP SL721P and RP SL721PF User s Manual User Setup User Name Password test iuf Show Password Confirm Password tesi User Group Administrator Operator O viewer Mote A user name and password must contain at least one character Max 14 characters are allowed in user names j The first character in user name must be A Z or a z Only A Z a z and 0 9 are allowed in the user name and password j Max eight characters are allowed in the password The maximum number of users is 20 The admin user is default user and cannot be deleted Figure 4 6 Security Setup Dialog Where User Name Enter the new user name to be added into the list see Note 4 of dialog for proper entry Password Enter the new password see Note 4 of dialog for proper entry Confirm password Enter the password again for authentication encoded display Show Password Displays the decoded password when check box is enabled User Group Three group options are available namely Administrator User is allowed to change Camera settings and perform all Camera functions Operator User is allowed to login Live View Webpage and perform all functions within this page Except changing Video and Audio settings of Camera live stream other adjustments of Camera parameter are prohibited Viewer User is only allowed to login Live View Webpage and pe
33. d To install the CAM FINDER from the Software Package CD select CAM FINDER then follow the instructions to complete the installation NOTE 1 In order to ensure Camera will be assigned IP Address properly please confirm the following things B Always consult your network administrator in order to avoid using a previously assigned IP address B Check if the Camera is powered on and correctly connected to the network E norder to connect to the Web based user interface of the camera the host PC must be in the same subnet For more information about subnets please consult your network administrator 6 e Installation and Setup RP SL721P and RP SL721PF User s Manual Chapter 2 1 Once CAM FINDER has been successfully installed on the PC notebook ultrabook double click Mouse left button to run the software 2 Click the Device Search to search the device in the LAN Model Name IP Address MACAddress innware apne we SEVA DR DNS2 DNS3 Http Port Figure 2 2 Find the Camera Device via Device Search button 3 Under your selected item double click the left Mouse button or Right click the Mouse button to open the Property Page item Single Device Setting CAM FINDER V1 0 3 n2 a A H Model Nome IP Address MAC Address Firmware Subnethlack Gateway DNS1 DNS2 DNS3 Http Port l RP SLT231PF 123 158 3 100 ED SE ED AA 4 4 A4 omnes AIL 0
34. e or liable for any of such altered statements Every care has been taken in editing this manual If there are any inaccuracies or omissions please inform our local office We cannot be held responsible for any typographical or technical errors We are not liable or responsible for incidental or damages caused by any misinterpretation of this publication Contents Contents Contents iii pott dut IN OUCS aed ceca tacen E ND UM dad MINNIE DEEP NI M MSN MIC RUM V 1 Introduction 1 Hardware OYN OW eee Suet stet ten ia totas Shore inafu E Ned E iU LODS Ro FIRM PU REE RENE EIS NE 2 2 Installation and Setup 5 2 1 Connecting Camera to Network through LAN Router Cable 5 2 2 Configuring and Finding Camera via Software cccccccccsssseeeseceeeeeecaeaeeeeeeeeeeeeaaas 6 2 2 4 Open the Websbased WI oc ccstatcctuctncsonsedasedeonnncasanaandeeeenttonnaadisaceaninensanaiesaees 11 3 Camera Live View UI Settings 13 IL OW EAE No DUO NET 15 2 2 Camera Live View UL Setting Tool e oeeccmeciesb PUn EERx CIERRE BU RRCEUA M Ox RE PERXENR VEU RUF CEU 16 4 Setup Execution 18 4 System Setup Execution eeeeessssssssssseeeeeeeee eene enee nnne eene nnn rn nn nensi nnns 18 A WMT ut 5 ME Eo ROREM 19 BM Wie Eco ORTOS EUER 20 AN ME cun 2 LN IS NIAMS MAN CC AD RET T 23 LS MER SUMO Ico Ecc 25 2 2 INCL OG SCP EXCCUU ON ssenarini niera UM Esau sud
35. ectors to support 1 Video Out 2 Audio In 3 Audio Out 4 Terminal Block for GPIO Please refer to following table of the pins definition of RJ45 o 1 Video Cable BNC Phone Jack Audio Out Phone Jack Audio IN m T m E T cc HI Terminal Block cgo RJ45 Terminal Block 1 la 3 3 5 ___ 5 4 6 Phone Jack PHONE PLUG Re Audio IN n 1 4 3 Phone Jack Audio Out d 4 3 Video Cable BNC T 4 e 3 RP SL721P and RP SL721PF User s Manual 3 e Introduction Chapter 1 Digital Output each digital output pin to COM Pinl is a photo coupled relay on Normal Open status ao External device can directly connect to the terminals However the current that will go through the 2 nodes must not exceed 130mA An external Relay can also be connected to the terminals as an implementation In DO NO this case current or and voltage limitation 1s specified by the external Relay Digital Input Only one set is designed in this Camera Model The internal device is also photo coupled D electrical relay and the external device can be simply an On Off switch Each set of On Off switch can be connected as one trigger source I Default Setting Short Pin4 and Pin5 with a wire PIN GN with a short wire to revert to factory default settings Break the short when the LED starts quick flashing and then camera will reboot automatically a few minutes D
36. efault Setting later Pin 6 Out GPIO Pin to GND for active or leave floating or 8 CVBS Out unconnected to deactivate Don t forget to connect Audio In Audio Out CVBS 4 e Introduction RP SL721P and RP SL721PF User s Manual Chapter 2 2 Installation and Setup 2 1 Connecting Camera to Network through LAN Router Cable 5 uiti aes 2j lees sspe a i j ae f Figure 2 1 Connecting IP Camera to Network 1 Prepare a PC notebook ultrabook with Ethernet link to the network 2 When PC notebook 1s used connect the LAN port of the device to the network router with an RJ45 network cable 3 Plug the DC power jack of the power adaptor GO to power jack on the extension cable of Camera and connect the power adaptor to power outlet 110V or 220V 4 Connect the network router to the LAN port on the extension cable of Camera with an RJ45 network cable 5 With power switched on a few minutes later you should find out this camera via CAM FINDER utility in CD RP SL721P and RP SL721PF User s Manual Installation and Setup e 5 Chapter 2 2 2 Configuring and Finding Camera via Software You could find CAM FINDER utility from the attached Software Package CD The CAM FINDER is used to find and configure network cameras on the LAN This utility is useful for conveniently configuring the network settings of the device or for finding a device once the network settings have been modifie
37. eo amp Audio Tabbed Panes RP SL721P and RP SL721PF User s Manual 4 3 1 Stream Tab The Stream tabbed pane see above figure provides the adjustments for the video quality of the Camera streaming function The pane offers the following three modes of video quality setting Video quality settings for stream 1 This is the primary quality setting for live view streaming Video quality settings for stream 2 This is the secondary quality setting for live view streaming Video quality settings for stream 3 This is the secondary quality setting for live view streaming NOTE If the Video Event Alarm Setting by Video see Section 4 4 2 is enabled an alert message will display requiring you to disable the feature first before proceeding to change the Streaming settings Otherwise adjustments to video quality streaming settings cannot be accomplished The quality setting items on this pane are as follows Connection template Four option modes are available Fast General Low and Customized modes Mode Three modes of encoding options are offered H264 MJPEG and MPEG4 Frame Size Three 3 types of streamed frame resolutions are available to selection 2048x1536 1920x1080 and 1600x1200 Maximum Frame Rate Available rate options are 1 2 3 5 8 10 amp 15 frames per second FPS 1080P Full HD available for 30 FPS Steaming Mode Two choices of s
38. era provide clear images even under backlighting RP SL721P and RP SL721PF User s Manual White Balance Because camera doesn t have ability to automatically adjust different color temperature to the environment six templates are provided to let you choose for different light White Balance Full Tungsten Lamp Video Orientation Cool White Fluorescent Light SunLight SunShade Day Night Threshold Set the illumination lux value 5 100 to auto trigger the Camera into day or night mode relative to luminance of the area under surveillance When the environment luminance becomes higher than the set lux value the Camera will auto switch to day or color mode Otherwise it will remain at night or Video Orientation rotate the image so it looks up side down This can be applied when camera unit must be ceiling mounted and the image is therefore reversed Night speed mode LPR Video setting page to select Night Speed Mode Setup Stream h Video Audio Privacy Mi Live View System Network Video amp Audio Event Local Storage Video Settings General DALE ight Speed Mode Template Brightness RP SL721P and RP SL721PF User s Manual Because the shuttle speed is 1 480 second for this mode so the whole picture is very dark at night Snapshot without extra light compensation as following RP SL721PF equipped fix focal and fix aperture lens it can only identi
39. fy license plate of vehicle at speed under 40 km hr in single lane view RP SL721P equipped vari focal and auto IRIS lens with larger aperture that can identify license plate up to 60 km hr in double lane view X Without extra IR projector at night the recognition condition of license plate snapshot by vari focal lens model is better than fix lens model For example License plate snapshot by fixed lens with license plate light aN RP SL721P and RP SL721PF User s Manual License plate snapshot by vari focal lens with license plate light in outside lane of double lane road Vari Focal Lens RP SL721P license plate night view with and without license plate light Without license plate light EE tx 1 RP SL721P and RP SL721PF User s Manual Fixed Lens RP SL721PF License Plate Night View without or only one license plate light Without license plate light Only one license plate light Vari Focal RP SL721P license plate day view vehicle at outside lane RP SL721P and RP SL721PF User s Manual 2 2014 07 25 15 33 49 Fixed Lens RP SL721PF license plate day view RP SL721P and RP SL721PF User s Manual 4 3 3 Audio Tab g Stream Y Video 2 aq A Privacy Mask b Audio Settings 3 Mute Volume Figure 4 15 Audio Tabbed Pane The Audio tabbed pane provides the following audio adjustments to your Camera Audio In port Mute Enable or disable mute function of the Camera s
40. ion area as described above CT click the Add button again A second default frame will pop up on the screen Drag amp resize the frame at the desired location 2 Repeat the above step to add more detection area frames NOTE Total defined motion detection areas cannot exceed 10 frames f Motion Video Snapshot Motion Settings W Enable Motion Detection GHI 2014 03 03 14 10 10 Figure 4 20 Defining Multiple Motion Detection Areas for the Camera 3 To assign unique names to each framed location for easy identification click on the frame and a Window Name text box with the default name of the save selected frame will appear at the bottom of the pane see figure below Enter a new name and click the Save button Wait for a while for the change to take effect Figure 4 20 Detection Frame Window Name Textbox RP SL721P and RP SL721PF User s Manual anc 4 To delete a frame that is no longer needed but was previously saved click on the unwanted frame and click Delete button The frame will disappear after a while 5 To delete multiple frames that are not yet saved directly click the Refresh button instead of deleting them individually The Refresh button will automatically clears all unsaved frames 4 4 2 Video Tab The Video tabbed pane sets the video recording trigger method to use when motion is detected by the Camera The four methods available for selection are Period Schedu
41. le Motion and GPIO Input each of which can be set up with user scheduled recoding time and duration as well as defining the video record file target destination Period This method will trigger the Camera video surveillance recording operation for a defined duration in seconds whenever motion is detected The video record may be provided to host by E mail FTP stored in the SD card Remote Disk as selected or through all of them Video Motion Snapshot Event Alarm Settings by Video Please note that there is no SD Card plugged in camera or the SD Card is not writable W Video Clip Trigger by Period v Video Clip Type Post event recording 5 v Seconds Time Lapse 10 v seconds Target to 3 E mail FTP 3 SD card Figure 4 21 Video Recording with Period Method Selected RP SL721P and RP SL721PF User s Manual B Schedule This method activates the Camera video surveillance recording operation continuously when the defined days of the week and set time of the set days are met Motion is ignored with this method Each recording time span 1s in accordance with the set duration in seconds and the video record is stored in the SD card Remote Disk as selected or through both of them Motion Video Snapshot Event Alarm Settings by Video Please note that there is no SD Card plugged in camera or the SD Card is not writable iy Video Clip Trigger by Schedule d Day id Sun R MON if Tue
42. m ex rcpt mail com 192 168 1 1 ex mail examples com or 192 168 1 1 SMTP Port 25 0 65535 SMTP E mail Server SMTP user name guest SMTP Password enone from mail com from mail com Use SSL TLS None MV Sender E mail Address While PPPoE protocol is selected you may have to enter some more information such as the above picture While Camera IP is changed dynamically because of PPPoE Network Connection its new IP Address will be sent to Sender E mail Address through SMTP service So you won t worry about the difficulty in Camera s Webpage access X As for the settings of SMTP Service kindly please contact with your E mail service provider After you confirm all parameters are correct and working properly you may enter them into the text area manually Port Settings HTTP Port Re define the existing HTTP Port number in the text box RTSP Port Re define the existing RTSP Port number in the text box After setups are completed click Save button to apply the settings RP SL721P and RP SL721PF User s Manual 4 2 2 DDNS Tab General e Multicast IP Filter Dynamic DNS Settings 3 DDNS Enable Provider dyndns com iv Link to http www dyndns com Host name hostname ex ddns test com User Name username Enabled check box to display password in decoded format 3 Show Password Password IDIIILIITI Update Time 1000 60086400 Seconds Status No connection Fig
43. ndow 2 Drag a ROI area on the image Quality lI Enable Only support H264 1 Note The maximum number of ROI is 4 Stream Video ROI Setting Video Stream CH3 2014 04 15 14 37 02 gt lt EM 30 10 30 Low High Quality 4a Figure 4 18 Defining a Single ROI Area for the Camera B Defining multiple ROI detection areas Audio Privacy Mask qn W Enable Only support H264 Enhance video quality of ROI Note The maximum number of ROI is 4 Set New ROI Area 1 Click Add to create the window 2 Drag a ROI area on the image 10 10 30 Low High 1 After satisfactory positioning of the first detection area as described above click the Add button again A second default frame will pop up on the screen Drag amp resize the frame at the desired location 2 Repeat the above step to add more detection area frames RP SL721P and RP SL721PF User s Manual Stream Video Audio Privacy Mask RO Stream Video Audio Privacy Mask mq ROI Setting ROI Setting Video Stream Video Stream W Enable Only support H264 IM Enable Only support H264 v 1 v CH3 2014 04 15 14 44 34 gt T gt Gs Note The maximum number of ROI is 4 Note The maximum number of ROI is 4 Set New ROI Area Set New ROI Area 1 Click Add to create the window 1 Click Add to create the window 2 Drag a ROI area on the image 2 Drag a ROI area on the image Quality 80 10 30 Low H gh
44. ng click the Recording button Snapshot Path Click Browse button to define Snapshot Path and C WUsers pigpigiDesktopi Snapshot Filename for the snapshots you are preparing to Snapshot file name capture 2013 0124 P Snapshot Path Specify a storage destination path for the snapshot images you are preparing to capture Snapshot file name Define base filename for the snapshots you going to capture The base filename will auto expand for each saved snapshot O To start capturing snapshots click the Snapshot button ace po Setting Language Setting Language Select the default language of the update more D user interface Camera settings English z Q Chapter 3 As you get familiar with features and functions of your Camera you may want to change or update a number of its settings to further upgrade its performance This can be accomplished by clicking the Setup button indicated in the above figure The Setup dialog see following figure will then display to provide the range of setup categories you will be able to change Setup Live View Network Video amp Audio Event Local Storage RP SL721P and RP SL721PF User s Manual CLA m System Information Model Name System Time Firmware Version MAC Address ActiveX control version Wired network Status Mode IP Address Subnet Mask Gateway Primary DNS Secondary DNS DDNS Server Status Security Maintenance System L
45. o open Camera s UDP Multicast Streaming function By default Camera s live stream belongs to RTSP Protocol It means camera has to send an individual streaming for each client wish to see the videos So the more the client number is the larger the network bandwidth required and the bigger loading of the camera In other words the camera can send just one streaming and each client can receive the streaming with Multicast Protocol Even with the client number increasing the network bandwidth is still the same loading with one camera Save After checking the Enable box to open this function click Save button to apply the settings RP SL721P and RP SL721PF User s Manual 4 2 4 IP Filter Tab General DDNS Multicast IP Filter IP Filter Settings Deny list Deny IP Range i After clicking Add button there Note Th amp gnaximum number of deny IP is 20 IP address input field expanding Start IP address ex 192 168 0 1 End IP address ex 192 168 0 254 Figure 4 12 IP Filter Tabbed Pane The IP Filter tabbed pane could let you configure device IP list which is denied access to this camera Where CD Start IP address Fill in the first address of IP range which you would like to deny its access to camera End IP address Fill in the last address of IP range which you would like to deny its access to camera X please note that total devices which are denied to access would be limited to
46. og RP SL721PF 2014 04 09 08 45 36 0 9 9 0319 6 2 EO GF EC AA AA AA 0 0 6 8 Connected STATIC 192 168 2 100 255 255 255 0 0 0 0 0 192 168 0 6 192 168 0 5 No connection Figure 3 7 Camera Setup Dialog Camera Live View UI Settings e 17 4 Setup Execution Setup Live View Network Video amp Audio Event Local Storage Remote Storage Figure 4 1 Camera Setup Selection Buttons NOTE For Live View setup execution please refer to the previous chapter Camera Live View UI Settings 4 1 System Setup Execution Clicking the System button will display the following tabbed panes relative to system configurations Setup information Time Security Maintenance System Log Live View ae O RP SL721PF Model Name Network System Time 2014 04 09 08 45 36 Video amp Audio Firmware Version 0 9 9 0319 6 2 Event MAC Address EO0 8F EC 44 44 44 ActiveX control version 0 0 6 8 Local Storage Wired network Status Connected Mode STATIC IP Address 192 168 2 100 Subnet Mask 255 255 255 0 Gateway 0 0 0 0 Primary DNS 192 168 0 6 Secondary DNS 192 168 0 5 DDNS Server Status No connection Figure 4 2 System Setup Tabbed Panes RP SL721P and RP SL721PF User s Manual 4 1 1 Information Tab Time Security Maintenance System Log System Information Model Name RP SL721PF System Time 2014 04 05 08 47 21 Firmware Version 0 9 9 0315 6 2 MAC Address
47. ould be made by qualified service personnel or system installers from our distibutor dealer RP SL721P and RP SL721PF User s Manual Chapter 1 1 Introduction RP SL721P and RP SL721PF is a IR Bullet Network Camera featured with 3Mega Pixel resolution and superior H 264 AVC performance and rich functions Itis very suitable to view a wide Tele area such as station commercial banking communication and government building schools and airport RP SL721P and RP SL721PF value added features include on board video motion detection and two way audio RP SL721P and RP SL721PF the PoE available full PoE IEEE 802 3af feature supplies power to the camera via the network eliminating the need for power cables reducing installation costs and complexity Consequently RP SL721P and RP SL721PF is Best in Class for maximum performance IP video surveillance systems demanding superior image quality ease of installation and intelligent video capabilities Further functions include DI DO alarm application and micro SD card support for local storage application RP SL721P and RP SL721PF User s Manual Introduction e 1 Chapter 1 Hardware Overview 2 e Introduction RP SL721P and RP SL721PF User s Manual Chapter 1 RP SL721P and RP SL721PF provide extra connections with outside devices via water proven RJ45 connector User can make the conn
48. rform all functions within this page Changing Camera settings is prohibited After setups are completed click Save button to apply the settings RP SL721P and RP SL721PF User s Manual 4 1 4 Maintenance Tab Setup Information Time Security System Log Live View Model Neme RP SL Z1PF Network Upgrade Firmware Select firmware file SD Video amp Audio Event Local Storage Download and save the latest firmware in the PC Upload Own Logo File Click here to browse and select it Right click he mouse buttar image in the PC Select image fle to uplosd ez Backup Save all parameters and user defined scripts to a backup file Backup Upload Setting Use a saved Backup file to return the unit fo 8 previous configuration Restore System Factory Default Figure 4 7 Maintenance Tabbed Pane The Maintenance tabbed pane allows you to upgrade the firmware with the latest version and to restore the Network Camera settings to factory default Where Upgrade Firmware Download the latest firmware file from the website by executing the following steps 1 Click the Browse button to access and select the appropriate firmware file from its folder 2 Click the Upgrade button The Network Camera will 9 then start to upgrade the existing firmware When upgrade is completed the Camera will reboot automatically Upload Own Logo File Prepare and save the Logo Image file in the PC Then Follow the
49. rily lower your security settings to perform a one time only installation of the ActiveX component onto your workstation as described below 1 From the IE Browser menu select Internet Options gt Security gt Custom Level 2 Set the security level to Low and click OK 3 Don t forget to restore the security level after the ActiveX installation 12 e Installation and Setup RP SL721P and RP SL721PF User s Manual Chapter 3 3 Camera Live View UI Settings Using PC notebook ultrabook you may change and reconfigure the Camera live view user interface UI settings to suit your need by following the procedures below 1 Execute your Web Browser and then manually enter the Camera Device s IP address gotten via CAM FINDER utility NOTE E For first time user there will be a prompt to install the ActiveX control Conply with the ActiveX installation as it is needed to view the video stream and some other operations B Use of Microsoft IE browser is recommended as it offers a better compatibility 2 Then the Windows Security dialog displays Enter a username and password You may enter admin for both Click OK button when completed Note that same Browser with different version or different vendor Browser will behave different dialog window Below picture 1s belonging to IE Browser s diagram Windows Security The server 127 0 0 1 at IP Camera requires a username and password Warning
50. talling this unit for its intended use Before the Network Dome Camera is installed carefully read and follow all the safety and operating instructions to avoid damage due to faulty assembly and installation This also ensures that the device 1s used properly as intended Heed All Warnings B Do not drop or hit the device Sensitive electronics inside the camera are vulnerable to excessive impact B Do not install the device under high temperature higher than 50 C environment Excessive heat could damage the equipment B Do not cover device with any object or install it in a poorly ventilated vicinity Overheating could damage the camera B Do not expose the device to rain or moisture Do not touch the power connection with wet hand Risk of short circuit electric shock or fire B Do not damage the power cord or leave it under pressure Risk of fire or circuit electric shock B To reduce the risk of electric shock or damage do not open the cover except qualified person There is no user serviceable parts inside Misusage improper or negligent handling could damage the device Refer to qualified service personnel from our distibutor dealer for any device related trouble shooting need RP SL721P and RP SL721PF User s Manual V vi Read Me First B Do not continue to operate the device if it appears to malfuntion Contact qualified service personnel from our distibutor dealer for help B Installation of the product sh
51. their properties together 255 255 2550 192168131 192168131 0000 55 955 192168121 192168131 192169131 192168131 192 168 13 1 192 168 13 1 0 0 0 0 192 168 13 1 192 168 13 1 0000 192 168 13 1 192 168 13 1 00050 0 0 0 0 0000 192 168 13 192 168 13 1 UUUL UUUL 0000 192 168 13 1 via Batch Device Setting item 122 168 13 31 255 255 255 0 192 168 13 1 Certification Use Custom zl 192 166 13 1 Usemame Password OE i I i ag i Figure 2 8 Check Increase IP setting to set Camera Device s IP address increasing one by one Then click Set button to save and enable the modification 7 Language support for Chinese English and Spanish CAM FINDER VL03 Model Name O RP SL721PF IP Address MACAddress 22 168 2 100 215 23 OU CO OWN Batch Device Setting Single Device Setting Open web DNS3 000g Http Port Figure 2 9 Selecting Language item could change the displayed language font of CAM FINDER utility 10 e Installation and Setup RP SL721P and RP SL721PF User s Manual Chapter 2 2 2 1 Open the Web based UI 1 To access the Web based UI of the selected unit run the Open Web on the select item Figure 2 10 Open the Camera s Web based UI Page via Open web item 2 For first time user there will be a prompt to install the ActiveX control Comply with the ActiveX installation
52. treaming modes are offered VBR variable bit rate and CBR constant bit rate Quality The options for streaming mode quality are expressed differently between VBR and CBR VBR Standard Good amp Detailed Bitrate CBR 64K bps 128K bps 256K bps 384K bps 512K bps 768K bps 1M bps 1 5M bps 2M bps 3M bps 4M bps 5M bps 6M bps 8M bps 10M bps and 12M bps RP SL721P and RP SL721PF User s Manual Intra frame period Available choices are 5 8 10 15 20 25 30 40 50 amp 60 frames per period This function will let you choose how long distance between two I Frames Lager value means longer distance between two I Frames and this selection 1s suitable for the stable Network Bandwidth Environment so we suggest the smaller value selection 1s proper to the worse Network Bandwidth Environment Text Overlay When enabled each streamed frame will be overlaid with the Camera ID text field and stamped with date time 1f enabled as illustrated below M Text Overlay Text Field CH1 i Time Stamp 2013 01 28 22 53 35 Figure 4 12 Text Overlay Setting Example RTSP Port Access Name When RTSP or VLC media player is used the port can be renamed with easy to remember pathname For example the de Default RTSP Port Access Name is livel sdp it means your stream name would be RTSP camera s IP address livel sdp Video Audio Privacy Mask Video quality settings for stream 1 Connection template
53. ure 4 10 DDNS Tabbed Pane The DDNS tabbed pane allows you to configure the Dynamic Domain Name System of your network device with a host name instead of the IP Address Where DDNS Enable Enable the check box to support DDNS function Host Name Enter the Host name which you registered and got through DNS Service Provider The assigned host name is used to access the network device instead of IP Address User Name Password Account authentication for logging into the website of DNS Service Provider Update Time Define a time interval for the device to periodically update and check its access status with website of DNS Service Provider After setups are completed click Save button to apply the settings RP SL721P and RP SL721PF User s Manual 4 2 3 Multicast Tab General DDNS Multicast IP Filter Multicast Settings Based on the RTSP Server Multicast Group Address 239 128 1 100 224 3 1 0 239 255 255 255 Multicast Port 5560 1 65535 Multicast TTL 15 1 255 Stream 1 3 Enable Multicast Video Port Multicast Audio Port Multicast Metadata Port Check the Enable box to open MS UDP Multicast Streaming function of stream1 2 or 3 Stream 2 3 Enable Multicast Video Port Multicast Audio Port Multicast Metadata Port Stream 3 3 Enable Multicast Multicast Audio Port Multicast Metadata Port Figure 4 11 Multicast Tabbed Pane The Multicast tabbed pane allows you t
54. ways popped even NetcamViewer is downloaded and installed successfully in your PC Please help to check if your IE Browser version is 11 first If it is yes kindly please help to refer the below steps to enable Compatible View settings of IE 11 Browser B http 192 168 33 198 Pre B Network Camera 19211683 X About Internet Explorer Internet Explorer 1 Version 11 0 96 6428 Un iate Versions RTM KB2841134 AA459 new versions automatically 2013 Microsoft Corporation All rights reserved Close RP SL721P and RP SL721PF User s Manual Find Tools icon and then select Compatibility View settings C3 J 55 http 192 168 33 198 D C Network Camera 1921683 X B File Edit View Favorites Tools Help Add site to Start menu View downloads Manage add ons F12 Developer Tools 9 Go to pinned sites A Compatibility View settings Loading sae Internet options About Internet Explorer You did not install the control properly Click NetcamViewer exe to download video control File Edit View Favorite TOE menie P e E nevon comesas Help Delete browsing history Ctrl Shift Del InPrivate Browsing Ctrl Shift P urn on Tracking Protection iveX Filtering connection problems REopen last browsing session site to Start menu Viel downloads Pop4up Blocker gt SmarScreen Filter ing Manage add ons pee 00 Subscribe to this feed

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents