Instructions > PMI Advantage
Contents
1. Other Features The Advantage features a built in goggle mount designed for use with ESS goggles Product HL33021 amp HL33023 and an optional mount for ear protection Three Point Suspension Three points of suspension means that in addition to the support points on both sides of the helmet A B a third point of support is positioned at the rear C The additional point helps to prevent the helmet from falling forward over the user s eyes ADDITIONAL INFORMATION For additional information about this or other PMI products contact us Pigeon Mountain Industries Inc PO Box 803 LaFayette GA 30728 PIGEON MOUNTAIN ee es PMI Red Orange Fluorescent Lime White Blue Phone 706 764 1437 HL33012 HL3301 1 HL33018 HL33014 HL33013 Fax 800 952 3747 or 706 764 153linpusTtRIES Email info pmirope com Web www pmirope com The PMI Advantage Helmet is designed to fit head circumference from 50 to 64cm 20 to 25in YOU COULD BE KILLED OR SERIOUSLY INJURED IF YOU DO NOT READ AND UNDERSTAND THIS BOOKLET BEFORE USING PRODUCT SPECIAL TRAINING AND KNOWLEDGE ARE REQUIRED TO USE THIS PRODUCT YOU MUST THOROUGHLY READ AND UNDERSTAND ALL MANUFACTURERS INSTRUCTIONS BEFORE USE USE AND INSPECT THIS PRODUCT ONLY IN ACCORDANCE WITH THE MANUFACTURERS INSTRUCTIONS YOU CAN CONTACT THE MANUFACTURER AT 706 764 1437 FOR IMPORTANT SAFETY INFORMATION Always keep the chin strap fastened while this helmet is being worn An unfas2. express or implied warranties on sales of PMI products Because of the high risks involved in high angle rope work such as but not limited to rescue rope access caving rappelling rock climbing and mountaineering no further warranties exist or are implied by PMI Regulations issued under the Magnuson Moss Warranty Act require us to include the following statement some states do not allow limitations on how long an implied warranty lasts nor the excluding or limitation of incidental or consequential damages so the above limitations may not apply to you WEBV 1 041 1 ltem Model Fitting and use Place the helmet on your head and turn the knob to adjust the head band The fit should be snug but not tight Snap the chin strap under Date Use or Maintenance Comments your chin using the quick disconnect buckle Adjust the chin strap by sliding the webbing through the ladder lock side of the quick disconnect buckle Excess length of the chin strap can be kept out of the way with the Velcro fastener Adjust the nape strap by sliding the rear webbing though the ladder lock buckle Always keep the chin strap fastened while wearing this helmet Removal To remove the helmet squeeze both sides of the quick release buckle The female side of the buckle should automatically eject from the buckle Strap Retainers Use the small bungees at the front and rear of your Advantage Helmet to attach a headlamp or the strap of your goggles if desired
3. 2PMI Instructions gt PMI Advantage PMI Q T a NFPA 1951 2007 ANSI Z89 1 Type 1 E G CERTIFIED Inspect the helmet for obvious damage Check the shell for cracks and dents Minor surface cracks will not impair the effectiveness of this helmet Check the webbing and buckles for damage or excessive wear MAINTENANCE AND CARE This helmet should be assigned to a single user who is responsible for inspecting it after each use Make sure that the surface of the helmet has no dents or significant cracks Inspect the webbing and buckles for damage or excessive wear If needed wash the helmet with clear water or a mild soap such as PMI Rope Soap Ordinary laundry detergent or solutions that may contain bleach should not be used on life safety gear Air dry in a cool dry place out of direct sunlight Store the helmet in a cool place where it will be protected from exposure to potentially damaging chemicals Repair or modification of this product without the manufacturers written consent is strictly forbidden You should establish a record of the inspections of this equipment You may need to develop your own inspection log format depending on your needs WARNING N This helmet is not designed to provide protection from the following hazards non ionizing radiation ionizing radiation external radiation or any condition not expressly stated in this use information The PMI Advantage provides the protection you nee
4. d working in a vertical rope world It features a Kevlar shell giving your head maximum protection It meets ANSI Z89 1 Type 1 and is NFPA certified Fully adjustable three point chinstrap and ratchet system provide a perfect fit Weight 1 25 Ibs 567 g REMOVAL FROM SERVICE If any of the following occur this helmet must be removed from service and destroyed If the helmet received a significant impact e If the helmet shows cracks that are more than superficial If any part of this helmet shows significant damage or excessive wear If the helmet is has been visibly damaged by heat chemicals etc e If this helmet has been in service for 5 years regardless of condition e If this helmet cannot be properly adjusted A comfortable well fitting helmet that is designed specifically for vertical work is essential Helmets must have a secure chin strap and a three point suspension to keep the helmet on the head when it is needed most A three point suspension refers to a helmet with webbing support points on both sides of the helmet and one at the rear The chin strap should also be designed so that a relatively high force is required to cause a release This helps keep the helmet on the user s head in a tumbling fall The inside suspension of the helmet should hold the shell away from the skull during a blow to the helmet and should provide air circulation and comfort particularly during hot weather The shell should have the r
5. igidity to resist impact to the helmet and penetration by sharp objects but be flexible enough to absorb some of the blow that otherwise would be directly transmitted to the skull and spine The design of the helmet should protect the head against objects falling from above and hitting from the side A slight brim helps prevent rainwater or spray from dripping into your face However your helmet should have a narrow enough profile to allow you a good upward field of vision and to ensure that the back of the helmet does not catch on a backpack when you raise your head CAUTION N Use this PMI Helmet only if you have been properly trained by an instructor who is well qualified in all phases of vertical rope work Good instruction includes evaluation of the students comprehension of and ability to safely and efficiently perform the task s being taught PMI LIMITED WARRANTY PMI products are warranted to the original retail purchaser to be free from defect in material and workmanship for a period of one year PMI will repair or replace the item without charge provided inspection at our factory discloses no misuse or alteration which in our judgment has affected the condition or functioning of the product All implied warranties imposed by law in connection with the sale of PMI products are also limited in duration to a period of one year PMI expressly excludes and shall not be liable for any consequential damages arising out of any breach of the
6. tened chin strap will greatly reduce the ability of this helmet to protect your head
Download Pdf Manuals
Related Search