APP0396-01
Contents
1. APP0396 01 15 01 02 KEEP WITH USER MANUAL HORNER APG Application Note for Using the Operator Station HE500TIU050 10X 11X 20X with the AuCom Soft Starter drive Protocol File Name HE500TIU050 IMS2_R 0xx HE500TIU1xx IMS2_R 1xx HE500TIU2xx IMS2_R 2xx The the TIU firmware revision Configuring the Operator Station To verify the Automated Equipment type the Operator Station is setup for watch the screen of the Operator Station on power up The first screen message details the setup of the Operator Station To configure the Operator Station for particular Automated Equipment select the Automated Equipment in the Communication Settings from the Configure menu in CBREEZE software Select the appropriate Manufacturer and the appropriate Remote Equipment Model Then from the File menu select Update Protocol the appropriate file name will appear in the file name field The programmer may need to point to the correct folder name location If further information is required see the manual or CBREEZE help on update change protocol Protocol Revisions Version 1 00 Supports master only operation to the Soft starter supporting two command types Command and Read Status Data WORD register ranges table 1 shows the parameter ranges Operation Range Command B10 B12 B14 B16 Read Status Data C10 C12 C14 C16 C18 D10 D12 Table 1 Operation types and ranges Serial Port Format The A2. S2 Soft Starter Drive Chassis EARTH DA_ B3 TX 485 422 DB BI RX 485 422 RX 485 422 OV GND SG B2 RX RS232 COI NDI MJRJ OWNM Re TX 4 20mA TIU100 TIU1 10 to an AuCom IMS2 Soft Starter Cable Screened Twisted Multipair Beldon 9503 One Pair Tx RXData One Pair for 0V Connect Screen to earth at DMC10 end TIU TX 485 422 ISM2 Soft Starter Internal Screw Terminal TX 485 422 RX 485 422 TIU050 TIU20X TIU1X1 TIU1X2 to i AuCom IMS2 Soft Starter Configuration Bank Switch ON OFF Pull up No Pull up 120 termination No termination Pull down Reserved for future use No Pull down NOTE Switch 1 and 3 must be used together Ensure TIU PLC Serial Port switch settings reflect any resistors on the TIU side mjm 4 3 2 1 SWi1 IMS2 Soft Starter Internal Screw Terminal Unit 1 Centrepoint Centre Park Rd HORNE OFF Rev Date TEL 353 21 4321266 AMG FAX 353 21 4321826 Date 03 Dec 2001 ON 10 03 12 01 Doc APP0395 Title Cable Dwg TIU AuCom IMS2 Soft Starter Drive Drawn By D T Rev 1 0 Current EO Sheet 3 of 3
3. uCom Soft starter operates by default with the following serial port configuration Status Baud Rate No Data bits Parity No Stop Bits Factory Setting 9600 8 None 1 Optional settings 2400 8 None 1 4800 9600 19200 Table 2 Serial Port settings Connection to the Soft starter is via a screw terminal inside the housing the interface is a two wire RS485 interface Horner Europe Tel 353 21 4321266 e mail tech support hornerirl ie Horner UK Tel 44 0870 8435363 Horner Electric APG Tel 1 317 916 4274 Fax 1 317 916 4287 www horner apg com Page 1 of 3 APP0396 01 15 01 02 KEEP WITH USER MANUAL Node Address This must be in the range 1 to 99 the node number or Satellite Address is stored in parameter 62 of the soft starter the factory default is 20 Unpredictable results will occur if two or more nodes on the network share the same node address Register Type Specification Only one type of Register is supported by the DMC10 CPL protocol Word Word Types e Command Read Status Data For details of the Command and Read Status Data parameters see the Soft starter s User s Manual Horner Europe Tel 353 21 4321266 e mail tech support hornerirl ie Horner UK Tel 44 0870 8435363 Horner Electric APG Tel 1 317 916 4274 Fax 1 317 916 4287 www horner apg com Page 2 of 3 CONNECTING THE OPERATOR STATION TO AN TIU 5V TX 485 422 TX RS232 AuCom IM
Download Pdf Manuals
Related Search
APP0396 01