User manual NORDIC - Crem International
Contents
1. The taste is to strong weak It constantly drips fluid from the outlet pipes Troubles with cooling system The drinks are not cold The dispenser is not cleaned properly The ejector is not adjusted correctly Dirt in the water valve Failure in thermostat Failure in cooling system 14 Clean ejector outlet pipes and pinch solenoid Call service Call service Call service Call service Call service Technical data Nordic Electrical connection Water connection Compressor Cooling gas Cooling capacity Cooling system Front light Front sign size Dispenser measurement Weight 230 V 50 Hz 2 5 A 3 0 m Tube with 3 8 internal thread minimum 2 2bar water pressure Elektrolux GL 80 HFC 134 a Amount to fill 240 gram 294 W Dry block with stainless steel pipes inside 24 W Fluorescent lamp 400 x 550 mm Height 745 mm With 385 mm Depth 560 mm 49 Kg Notes Nordic Note 1 Note 2 Note 3 Note 4 The thermostat is factory adjusted and improper adjustment may cause the cooling system to freeze causing damage or water leakage in the dispenser It is strongly recommended to use some sort of water isolator in the water line in case of an emergency leakage Maximum ambient temperature in the room where the dispenser is located should not exceed more then 25 C lf the dispenser has frozen check water tubs and connections inside the dispenser b2. User manual NORDIC Juice machine U EN Rev 090921 Dispenser description for Nordic Nordic is a dispenser for cooling water and mixing juice concentrate to a ready to drink product The dispenser is for three non carbonated drinks and chilled water The dispenser is connected to the water mains by a pressurised tube and to an electric wall socket by a power plug The water pressure is adjusted with the water regulator and the pressure is displayed on the manometer The water is chilled by the cooling block which in its turn is chilled by the air cooled compressor The water temperature is adjustable with a thermostat The mixing ratio product water is adjusted with the ejectors Pushing one of the four buttons on the front panel dispenses the mixed product or water General Read the instructions carefully before you start working with this equipment The equipment should be installed and serviced by trained staff Dispenser description Nordic KONE gen Water regulator with manometer The water regulator can be adjusted up to 6 bar The minimum pressure is 2 2 bar Note When adjusting the pressure dispense product Venturi ejector The mixing ratio is adjusted on the ejectors When water flows through the ejector the concentrate mixes with the water The mixing ratio is regulated on the ejector There are two kinds one for products with cells and one for products withou
3. ace the bag in box in the dispenser and connect it to the pinch solenoid valve and ejector Pushing the centre of the pinch solenoid valve and sliding the tube in from the side fixes the tube Cut the tube to correct length and push it onto the elbow connector on the ejector Place a cup under the outlet pipe Dispense a glass of product by pressing the push button Check that the brix value mixing ratio is okay if not adjust To adjust the brix use the adjustment screw on the ejector The dispenser is now ready to use Maintenance Nordic Change of bag in box Turn the box so the perforated side is turned upwards Brake the perforation on the box and place the main pipe in the punched hole Place the box in the dispenser so that the tube points down to wards the pinch solenoid Press the end of the pinch solenoid and insert the tube from the side Check the tube length so that it will reach 1cm into the venture nipple If the tube is to long cut it to the right length Slip the tube to the venture nipple Make sure that the tube is not twisted and shut the door to the dispenser Place a cup under the outlet pipes and draw until the juice comes out Daily cleaning Clean internal and external surface with a damped rag Use the cleaning brush to clean the outlet pipes Wet the brush in water and put it in the outlet pipe from the inside of the door Clean the drip tray 10 Maintenance Nordi
4. c Periodic cleaning 1 Disconnect the bag in box tube from the venture 2 Fill the cleaning bottle with warm water and some washing up liquid and connect it to the venture 3 Shutthe dispenser door and put a cup under the outlet pipes rinse the venture and the outlet pipes by pressing the respective push buttons 4 Use the cleaning brush to clean the outlet pipes Return the boxes and connect the tubes to the ventures 11 Handling and cleaning instructions Nordic 1 Open the Bag in Box at the perforation Pull out the silicon tube and the plastic connector so it is clear of the box 2 Place the box inside the dispenser Press in the pinch solenoid and slide the tube in to the opening Fig 2 3 Push the tube onto the ejector nozzle Fig3 4 The dispenser is now ready to use 1 When changing the Bag in Box the dispenser should be cleaned with hot water 2 Fill the rinsing bottle with a solution of hot water and a sanitising agent Add two drops of washing up liquid Connect the tube to the nozzle and wash it through Fig 4 3 Wet the brush in a hot water and sterilising solution Clean the outlet pipes by pushing the brush all the way through the pipe and back again Fig 5 4 Rinse the pipes with the water solution from the bottle 5 The pinch solenoid that the tube runs through should be cleaned on a regular basis by pouring a hot water and sterilising solution over it This will
5. dissolve any residual concentrate 6 The air inlet condenser at the back of the machine should be cleaned from dust on a regular basis by brushing or vacuuming the grid 12 Trouble shooting Nordic Probable cause Attend to Concentrate is Dripping from outlet pipe Mostly water or only water coming from outlet pipe Nothing happens when I push the buttons and there is no clicking sound Nothing happens when you push the buttons and there is a clicking sound The tube is not properly fixed into the pinch solenoid valve The tube is kinked due to incorrect length The pinch solenoid needs cleaning The tube is twisted No power to the valves Thermo fuse in the transformer has cut On older models a fuse has blown Water supply turned off Water regulator turned off or failed Manometer 0 bar The cooling coil has frozen Manometer max pressure 13 Fix the tube properly into the pinch solenoid valve Cut the tube to correct length Clean pinch solenoid with hot water Untwist the tube The bag is empty Replace bag Check the valve on off key switch inside the door Remove power to the dispenser and put it back on after 10 sec Change fuse Check water supply Check water regulator change needle valve in water regulator Shut off water supply and call service Trouble shooting Nordic Probable cause Attend to
6. efore running the dispenser again 15 Dimension sketch 260 SVZ JOD 16 COFFEE QUEEN NORDIC Juice machine COFFEE QUEEN OF SWEDEN FOR SERVICE Please contact your retail dealer Din terf rs ljare Your retail dealer COFFEE QUEEN AB Box 960 671 29 ARVIKA bes ksadress Korpralsv 1B Tel vxl 46 0 570 47700 Fax 46 0 570 47719 E mail info coffeequeen se www coffeequeen se Art nr Art no 1704145
7. particle filter A large particle filter is fitted between the cooling block and the water valves It is possible to rinse the filter if needed Installation and users instruction Nordic peu T Unpack dispenser from the packaging and ensure that nothing is damaged Place the dispenser to it s position Note The dispenser weights about 49 kg Don t lift by door front panel Allow a space of min 40mm around the frame for air circulation Place the machine on a flat level and waterproof surface If necessary adjustment with the adjustable feets 60 mm from wall min airflow Use a water level tool for correct placement of machine lf needed adjust foot up or down Installation and users instruction Nordic ran Tee Connect the water hose from the dispenser to the cold water mains do not forget seals Turn on the water and check for leaks Note It is strongly recommended to use some sort of water isolator in the water line in case of an emergency leakage Connect the power plug to the wall socket Now the compressor starts and the front panel lights up The water pressure is factory adjusted to 2 2 bar which is the correct working pressure Check by pressing and holding one product button and reading the manometer If there is variations adjust by pulling up knob and turn it until you get a reading of 2 2 bar Installation and users instruction Nordic EC Pl
8. t cells ao Turn the adjustment screws according to the label on the ejector in order to increase or decrease the amount of concentrate Dispenser description Nordic KLEE BEKO Water valve The Water valve is connected to the ejector and opens the water flow Push button Apelsin Vatten A lg A Orange Waler pelsin Apple Orange Apple The push buttons on the front panel controls the water valves a Use only one button at atime Cooling block The cooling block is a flow through block with three built in stainless steel coils The coils are for water refrigerant R134A and thermostat Transformer The transformer is a 230 24 V 32 VA The transformer supplies 24 V to the magnetic valves E z 1 Th i j a i i Dispenser description Nordic pe m Thermostat The thermostat keeps the temperature within correct range Factory adjusted do not adjust this may cause damage and water leakage in the dispenser Illumination Behind the front panel there is a low energy fluorescent lamp with the effect off 24W The fluorescent lamp is a PL lamp Change low energy lamp Loosen fronitplate 4 screws A hold the frontplatte see B Lift out frontplate C and change lamp assemble the frontplate Dispenser description Nordic KLEE s Drip tray It is possible to connect drainage to the drip tray Large
Download Pdf Manuals
Related Search