view/download manual - Jumpking Trampolines
Contents
1. 6 and insert it into the Pod Connector 5 of the left hand end of part C 3 Then take the W Leg 7 and insert this into the Straight Leg 6 as shown Then take a second Straight Leg 6 and attach it to the W Leg 7 Do not insert it into the Pod Connector yet Now grasp the free Straight Leg 6 and pull until it lines up with the Pod Connector 5 attached to top rail D 4 By placing your hands further down the Straight Leg 6 you can increase your leverage when inserting the Straight Leg 6 into the Pod Connector 5 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines As before you should place your feet on the top rails either side of the Pod Connector 5 to steady the assembly as shown in the image Once you have inserted the Straight Leg 6 push down firmly on the W leg 7 to ensure a tight fit The tension of the W leg assembly helps hold the top rail pieces together Repeat this with the remaining C 3 D 4 top rails and 2 x Pod Connectors 5 so you have 2 identical segments Please refer to these segments as Assembly 2 as shown below amp Assembly 2 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional gui2. JUMPICING Trampolines Now take Safety Enclosure Netting 16 and spread it across the trampoline There is a stitched sleeve at the top of the net Make sure the sleeve is spread out flat across the bed This will make assembly easier Then UMKING open the Velcro flaps of the sleeve PE WORLD FANURITE Then take the black G3 Pole Sections 18 You will see these poles are connected with an internal elastic cord as shown Please unfold and join the G3 Pole sections to make a long pole Then repeat this with the remaining G3 Pole so you have 2 x long black poles Take one of the completed long G3 Poles 18 to the Net 16 Then locate the channel inside the stitched sleeve at the top of the Net 16 Insert and push one of the long G3 Poles 18 into the stitched sleeve as shown This process will be much easier if the Net 16 is flat across the trampoline Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 12 JUMIPKING Trampolines Make sure the long G3 Pole 18 passes through the semi circular openings and then goes back into the stitched sleeve at the top of the Net 16 The G3 Pole 18 will become visible at the opposite end of the Net 16 Then repeat this process with the second G3 Pole 18 in the parallel stitched sleev
3. requires a minimum of 2 people Use gloves to protect your hands during assembly J JUMIPKING Trampolines Now take 1 x Straight Leg 6 and insert it into the Pod Connector 5 of the left hand end of part A 1 Then take the W Leg 7 and insert this into the Straight Leg 6 as shown Then take a second Straight Leg 6 and attach it to the W Leg 7 Do not insert it into the Pod Connector yet Now grasp the free Straight Leg 6 and pull until it lines up with the Pod Connector 5 attached to top rail B 2 By placing your hands further down the Straight Leg 6 you can increase your leverage when inserting the Straight Leg 6 into the Pod Connector 5 You can also place your feet on the top rails either side of the Pod Connector 5 to steady the assembly as shown in the image Once you have inserted the Straight Leg 6 push down firmly on the W leg 7 to ensure a tight fit The tension of the W leg assembly helps hold the top rail pieces together Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines Repeat this with the remaining A 1 B 2 top rails and 2 x Pod Connectors 5 so you have 2 identical segments Please refer to these segments as Assembly 1 as shown below
4. Assembly 1 Top Rail Assembly Top Rails C and D Assembly 2 In the previous steps you assembled 2 of the 4 frame segments You will now build the remaining 2 frame segments using the top rails marked as C 3 and D 4 To assemble these segments please lay out the top rail parts marked C 3 and D 4 as shown below see drawing 1b on page 15 of the user s manual for reference Make sure that the parts are laid out in the order shown below so that 2 spring holes can be seen on part C 3 and 3 spring holes can be seen on part D 4 Also make sure you have a Pod Connector 5 on the left hand end of part C 3 and on the left hand end of part D 4 Important Please pay close attention to the position of part D 4 Make sure it curves the same way as part C 3 Y h Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines Please make sure that the spring holes in the square ends of top rails C 8 and D 4 align with the openings in the Pod Connectors 5 as shown on the right You may have to lift the top rail off the ground to check this Once you have checked the spring holes are correctly aligned with the Pod Connecter 5 push parts C 3 and D 4 together as shown Now take 1 x Straight Leg
5. JUMPKING Trampolines This is a supplementary guide to assembling the 8ft x 11 5ft OvalPOD Please ensure you have read the OvalPOD User s Manual before referring to this guide This document aims to provide a user friendly guide to building the OvalPOD with additional images and alternative techniques Building the Frame Top Rail Assembly Top Rails A and B Assembly 1 Start by assembling the top rails The easiest way to put the trampoline together is in 4 individual segments For the first of these 2 segments please lay out the top rail parts marked A Key No 1 and B Key No 2 as shown below see drawing 1a on page 15 of the user s manual for reference Make sure that the parts are laid out in the order shown below so that 2 spring holes can be seen on parts A 1 and B 2 Also make sure you have a Pod Connector 5 on the left hand end of part A 1 and Pod Connector 5 on the left hand end of part B 2 Please make sure that the spring holes in the square ends of top rails A 1 and B 2 align with the openings in the Pod Connectors 5 as shown on the right You may have to lift the top rails off the ground to check this Once you have checked the spring holes are correctly aligned with the Pod Connecter 5 push parts A 1 and B 2 together as shown Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly
6. Tube 13 and Straight Pole 12 If not already fitted slide the Foam Sleeves 14 on to the Enclosure Top Tube 13 and Straight Pole 12 Find the tapered end of the Straight Pole 12 and insert it into the Enclosure Top Tube 13 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPING Trampolines Then screw the poles 12 13 together using a self tapping screw 19 Repeat this with the remaining poles so you have 8 identical assemblies Take one of the completed Enclosure Poles and carefully lay it flat on the trampoline bed with the end of the Straight Pole 12 towards the Pod Connector 5 at the edge of the frame Then lift the edge of the Safety Pad 9 Carefully push the Straight Pole 12 through the opening in the Safety Pad 9 Then insert the end of the Straight Pole 12 into the opening of the Pod Connector 5 Please ensure that the Enclosure Top Tube 13 points towards the centre of the trampoline bed Repeat this step to attach all 8 x Enclosure poles 12 13 as shown Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 11
7. de to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines Frame Completion You have now completed the 4 individual segments of the OvalPOD frame You will have the following 2 x Assembly 1 each comprising top rails A and B with W leg 2 x Assembly 2 each comprising top rails C and D with W leg Assembly 1 Assembly 2 Top rails A and B Top rails C and D The following steps will require a minimum of two people We recommend you wear gloves Now turn over 1 x Assembly 1 and 1 x Assembly 2 and join these 2 segments together by inserting the free end of top rail B 2 into the free Pod Connector of Assembly 2 as shown in the picture below Assembly 1 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines When connecting the Assembly 1 and Assembly 2 you should see that the spring hole in the square end of top rail B 2 aligns with the free Pod Connector of Assembly 2 Once these 2 segments are connected turn over the remaining 1 x Assembly 1 and 1 x Assembly 2 and connect these segments in the same way You will now have 2 halves of the completed frame Car
8. e at the top of the Net 16 Make sure that you have a connecting sleeve on one of the black G3 Pole sections as shown Now join the 2 x G3 Poles 18 at the top of the net together using the connecting sleeves at one end of the G3 Poles This requires two people Please ensure you wear gloves Each person should grasp the two ends of the G3 Poles 18 and push towards each other as shown This will make it easier to join the 2 x G3 Poles 18 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines Connect the G3 Poles 18 using the connecting sleeve as shown When the Poles are connected please close the Velcro flap of the sleeves The Net 16 will now be an oval shape The next step is to hang the Net 16 on the 8 x Enclosure Top Tubes 13 First rotate the Net 16 and G3 poles 18 so the zipped entrance of the Net is by the Jumpking logo on the Safety Pad 9 Locate the 8 x exposed areas of the G3 Pole 18 at the top of the Net 16 as shown Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 14 JUMPING Trampoline
9. efully maneuver these 2 halves together and join them again ensuring that the spring holes in the square end of the top rails align with the open Pod Connector as shown above This process will require a minimum of 2 people In order to complete the frame the 2 people may have to support and push the frame from opposing ends You will now have a completed OvalPOD frame Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPICING Trampolines Trouble Shooting Should you need to establish if you have correctly assembled your OvalPOD frame you can check that your top rails are in the correct order Start by locating top rail B 2 on your frame this will be the apex of the oval shape Standing on the outside of the frame by part B 2 walk around the frame in a clockwise direction If your frame parts are in the correct layout you should find you have the following order of top rails BC DABCDA as shown in the image above Make sure the top rails are securely joined lf correctly assembled you will find that all of the curved top rail parts will have 2 spring holes on the underside with the exception of top rails D 4 which have 3 spring holes on the underside lf this is not the case you may have assembled some frame parts upside down Please dismant
10. er s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 16 JUMPKING Trampolines The Next step is to secure the Frame Pad 9 to the Trampoline Frame You will find a series of straps and metal D rings around the edge of the Frame Pad 9 Secure the outer straps to the Top Rails as shown Do not over tighten the straps There is a second series of elasticated straps around the inside edge of the Frame Pad 9 Tie these straps by hand around the nearest spring 10 The final step is to attach the Safety Placard 17 to a top rail by the Net entrance using the included plastic tie Make sure all the parts are securely attached Familiarise yourself and all trampoline users of the trampoline with the Safety Information and the Care and Maintenance details before use You have now completed your OvalPOD Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly 17
11. le you OvalPOD frame and reassemble Attaching the Jumping Bed and the Surround Pad We advise that you wear gloves and protective eyewear for the following steps Take the Stitched Bed Key No 8 and lay it on the ground inside the trampoline frame as shown You will see a series of V rings around the edge of the Jumping Bed Make sure the 2 warning labels are on the top of the bed Next find the 4 x V rings with yellow stitching There will 2 x V rings with yellow stitching located near each of the 2 warning labels at the North and South points of the Bed The diagram below details the spring attachment sequence To attach a spring 10 first hook the more tightly curled end onto the bed 8 as shown and then use the spring tool 20 to connect the spring to the frame n g X ihe SS Make sure you wear gloves when attaching the springs Please refer to the diagram below for the spring attachment sequence Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUBRIPKING Trampolines This diagram shows the initial order of spring attachment Top Spring Hole Sliver Top Spring Hole Yellow O Under Spring Silver Firstly locate the 4 V rings with yellow stitching These V rings are to be attached at points 1 2 3 a
12. nd 4 using silver springs 10 Then attach springs 5 to 12 in the order shown in the diagram These are all Yellow top springs 11 Th yy yy hi raat Important Remember to include the under spring holes when counting the V rings on the frame and bed Then attach springs 13 to 20 in the order shown in the diagram These are all yellow springs 10 Once all of the springs shown in the diagram have been fitted the remaining silver top springs can be attached Then please attach the under springs 10 to the underside of the top rail Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMIPKING Trampolines Make sure all of the top springs and under springs are attached Pr 2S Pen a Warning Do not use the trampoline until the surround pad and the safety enclosure have also been fitted Now take the Safety Pad 9 and spread it out on the trampoline Rotate the Safety Pad 9 so the holes align with the Pod Connector 5 as shown so the Jumpking logo covers one top rail D 4 Do not fasten the Surround Pad to the Frame at this stage as this will be done later Assembling the Safety Enclosure You will now assemble the Safety Enclosure for your OvalPOD trampoline Take the Enclosure Top
13. s Then stand on the trampoline bed and insert the exposed sections of the G3 Pole 18 into the first Plastic Cap 15 of the Enclosure Top Tube 13 Please refer to the below image for the sequence of hanging the Net 16 on the Enclosure Top Poles 13 Notes Please read this document in conjunction with the OvalPOD User s Manual This is an additional guide to assist OvalPOD assembly Assembly requires a minimum of 2 people Use gloves to protect your hands during assembly JUMPKING Trampolines You will now secure the bottom edge of the Net 16 to the V rings of the Jumping bed 8 Take the pack of PP Ropes 21 and select a single rope Take the single rope 21 and push the red needle end through the bottom of the net 16 This image shows inside of the net You may find it easier to perform this step whilst on the Bed 8 inside the Net Please ensure you can exit via the zipped Net entrance before complete this step Continue and push the Rope needle 21 through the V ring of the Bed 8 and then back arer i towards you ZETE ates a8 SES eee eae SS Keep the Net 16 and the rope taut as you sew Repeat this process making sure the net is sewn to every V ring When you come to the end of the Rope 21 tie it to a V ring and begin with another Rope 21 Continue this process until you reach your starting point Notes Please read this document in conjunction with the OvalPOD Us
Download Pdf Manuals
Related Search