Page 1 USER MANUAL PROTON POWER CONTROL PVT. LTD
Contents
1. controller will send SMS only to the Ist location number out of 3 registered no s in the phonebook 2 Motor can be Started Stopped by sending START STOP SMS through phonebook registered numbers only 3 The controller will reply to STATUS SETPOINT and LISTNUM SMS only if the senders number is registered in the phonebook B VIA CALL The Proton MPU has inbuilt Interactive Voice Response System VRS controlled start stop and remote monitoring User can control the motor by voice call to the controller if his number is registered in the controller phonebook While the call is on the motor starts if users presses 1 on his mobile likewise stops if 2 is pressed SMS of present state is received if 3 is pressed and a present condition of the motor can be heard if 4 is pressed Function Mode Set key is used to enter Function mode to view change settings When function key is pressed for 2 3 seconds then pwrd message is displayed and then 0000 user can change the password by pressing increment and decrement keys to enter the password press enter If user enters correct password the controller enters Function mode after entering Function mode settings can be viewed by going on pressing the Function key The default password for the unit is 5 11 amp 20 Note Over Load fault trip time is applicable as per Inverse trip time curve SMS format for changing parameter values via SMS Sr SMS Function No Saveul000 Set und2. USER MANUAL PROTON POWER CONTROL PVT LTD PUNE GSM BASED MOTOR PROTECTION UNIT Salient Features 1 Fully programmable Suitable for three phase pumps up to 25HP Relay outputs for Star Delta starters No auxiliary power supply required for controller operation Can be operated in 3 modes such as GSM AUTO MANUAL GSM based SMS controlled start stop and remote monitoring GSM based Interactive Voice Response System IVRS controlled start stop and remote monitoring for 3 registered numbers 8 IVRS Voice response available in regional language 9 Live Motor operation Status available via SMS as Motor ON OFF status Live Fault phase voltages and current drawn per phase 10 Inbuilt phone book for auto reply in case of faults 11 Password protected phonebook registration process 12 Complete protection from electrical unhealthy condition 13 All parameters are password protected 14 All parameters are settable through front key 15 LED indications for alarm fault 16 Scrolling display of parameters one by one in scroll mode eS D e INC Up scroll the parameter amp parameter value e DEC Down scroll the parameter amp parameter value LED S 1 UV RED Under Voltage Fault 2 OV RED Over Voltage Fault 3 SPP UB RP RED SPP Voltage Unbalance amp Reverse Phase Fault 4 UL CUB RED Under Load amp Current Unbalance Fault 5 OL RED Over Load Fault 6 Relay Green Supply Heal
3. er load to 0 Saveol010 Set over load to 10A Saveov450 Set over voltage to 450V 4 Saveuv150 Set Under voltage to 150V e ra o E Sree o ae Te C o re e PROTON POWER CONTROL PVT LTD PUNE Parameters Sr Parameter Disp Def Min Max Unit No Name msg value Limit Limit To change following parameters press SET key for 2 3 seconds and enter password via INC DEC key as a 5 1 Relay ON rLon 10 5 300 Sec B a a a a dva e S P e Fo Voltage vie e S S O Voltage Under drUn 10 00 A a S oem a e e e e To change following parameters press SET key for 2 3 seconds and enter password via INC DEC key as a 11 t lumme O E e e oo Unbalance O ue O fof LR Unbalance jai Ginan ae far Trp Plime S pe S Enable Voltage trip time eee S T Voltage trip time KONE SF D D Time Plime FF trip time jp fp LE trip time It Itcr oe ia a A E a tr p time oe ratio kadna Reset selection GSM Auto Enable To change Phonebook Registration password press SET key for 2 3 seconds and enter the old Phonebook Registration password then enter the new password via INC DEC key and to save press SET key Phonebook GPAS 20 0 9999 NA Registration Password PROTON POWER CONTROL PVT LTD S NO 28 JAGTAP DAIRY PIMPLE NILAKH PUNE 411027 TEL 020 2727 0800 27276777 TEL FAX 020 2727 0100 MOBILE 9764885010 9422009655 E MAIL rdpawar protonpowercontrol com agrosales protonpowercontrol c
4. ing STATUS Replies the present status of the controller to the 2 Position Panel sender 3 Enclosure 125 W X 275 L X 210 H mm SETPOINT Replies the present parameter set points of the 4 Terminal Screw ON Terminals controller to the sender LISTNUM Replies the list of numbers registered in the phonebook of the controller to the sender KEY S SET This key is used to change the controller from RUN mode to FUNCTION mode for Parameter setting amp to save the modified setting in Function mode USER MANUAL REG sect Registers the number inside the controller phonebook NOTE 3 numbers can be stored in the phonebook Syntax REG k kk kk HHHH 1 represents 1 location of phonebook represents 10 digit mobile number represents 4 digit mobile registration password E g If Phonebook registration password is 20 E g 1 If user sends REG191919191910020 To the controller the controller writes the mobile number 9191919191 to the 1 location of phonebook E g 2 If user sends REG291919191910020 To the controller the controller writes the mobile number 9191919191 to the 2 location of phonebook NOTE 3 numbers can be stored in the phonebook E g 3 If user sends REG391919191910020 To the controller the controller writes the mobile number 9191919191 to the 3 location of phonebook NOTE 3 numbers can be stored in the phonebook NOTE 1 If any fault occurs to the motor
5. ment display on unit 18 Inverse Time trip curve for over load fault The Motor protection unit continuously scans the faults like Under Voltage Over Voltage SPP Reverse Phase Voltage Unbalance Under Load Over Load Current unbalance 150 Technical Specification E g If Overload set point is 8A amp actual current is 9 6A then it will take 20sec 120 to trip Relay Input Current 0 18 A per phase Accuracy Voltage 0 25 1 dgts 2 Current 0 25 1 dgts NOTE The under load and Over load faults will not sense until the feedback input is received i e contact gets closed Output contact Rating 7 A at 250 volt Relay Auxiliary Power No External power is required Draws power from the voltage signal Inputs GSM MODEM Quad Band 850 900 1800 1900 MHz Environmental 1 Working Temp 0 to 55 C 2 Storage Temp 10 to 70 C GSM Control A VIA SMS The GSM control can be enabled or disabled using the programming menu If the GSM control is enabled the motor will start if START SMS is received by the controller The motor stops if any fault occurs or STOP SMS is received by the controller If any fault occurs the controller will send an SMS which contains current fault status to 3 mobile numbers stored in the controller The control SMS are as explained below oOo e 3 Relative humidity 0 95 non condensive 4 Warm up time 30 Sec Enclosure r 1 Mounting Surface mount
6. om
7. thy No fault WORKING Run Mode At Power On under normal working condition Relay indication led will blink and glow steady after power on delays Steady glow of Relay led indicates Relay on condition Unit will enter Run Mode and will have a scrolling parameter display consisting of R Y Voltage amp R Y B current drawn by each phase amp Coverage range of GSM Modem In Run mode Relay may turn OFF depending on the occurrence of fault ALARM indications for the particular fault will glow on the front panel of unit Faults such as over under load will turn off relay and faults such as over under voltage will turn off voltage relay Manual control for restart after occurrence clearance of fault has been programmed therefore user has to press decrement key to restart the unit The unit will resume Run mode if fault disappears after delay The Front panel provides fault indication by glowing red led s for over under voltage over under load single phasing unbalance amp phase reverse User can view the parameters in Run mode display and can Hold any Run mode parameter by pressing increment key in RUN mode If Auto timer Enable Aute is Yes then pump will run for time set in Auto Timer Autr it is applicable in Both Auto Manual mode In Overload condition when Itcr is selected as NO then it will take 2sec settable to trip Relay amp if selected as yes then the relay will Trip as following condition 17 Four bright 7 seg
Download Pdf Manuals
Related Search