Geemarc AMPLI600 Emergency Response Phone User Manual ()
Contents
1. Press C twice to exit Area and Long Distance Code Setting When you use your phone for the first time or if you have moved to a different area code you need to enter your area code into the phone This assures that when dialing a call out of memory or your phonebook the number is formatted properly To set your area code amp LDS Code Press MUTE I Use A or to select SET PHONE Press OK Use A or to select SET AREA amp LDS l Press OK Use A or to enter your area code The phone accommodates up to six 6 digits allows for International codes Once you have entered your area code even if you are not using all six 6 digits press the OK button until you reach the SET LDS CODE screen The LDS Code is your long distance code In the U S your long distance code is 1 The telephone is pre set for the U S NOTE Do not change the LDS code unless you are leaving the U S If you wish to change the LDS use A or Y to enter your LDS code I Press OK to confirm l Press C to exit 17 Answering A Call During an incoming call your phone will ring and then the number and or the name of the caller will be displayed on the screen if you have subscribed to a Caller Display service Using the handset e Lift the handset and speak e To end the call replace the handset Hands free e Your Ampli600 allows you to speak hands2. Use A or to select SET PHONE Press OK Use A or F to select LCD CONTRAST Press OK Use A or to select the contrast level that is correct for you Press OK to exit it will automatically return to time and date screen Auto On Hook When this feature is ON if you leave the telephone off the hook by mistake the AMPLI600 will automatically disconnect the line after 5 8 minutes and your telephone will be ready to take another incoming call Press MUTE Use A or to select SET PHONE Press OK Use A or to select AUTO ON HOOK Press OK Use A or to select ON or OFF Press OK to confirm Press C twice to exit 15 Auto Screen Sizing DIM X gt x The phone can show a maximum of 8 digits at full size You can choose to see the complete number up to a maximum of 18 digits by selecting Auto Screen Sizing When activated the phone will display at full size but automatically switch to display small numbers when there is a number with more than 8 digits The default on arrival is activated However if you ever need to change this setting see below Press MUTE Use A or to select SET PHONE Press OK Use A or to select DIM X gt x Press OK Use A or to select ON or OFF Press OK to confirm
3. clearly into the speakerphone You must be less than 1 ft away from the phone The message can be up to 10 seconds long A good example of a message would be This is Mrs Doppler l have a problem please press any key on your keypad to talk and listen Press OK to stop recording I Press C three times to exit 24 Play the Emergency SOS Message Press MUTE Use A or to a SET SOS OK Use A or to m SOS SOUND i Press OK Use A or to select PLAY SOUND I Press OK to play your message Press C three times to exit Using the Emergency Contact Telephone Once the Emergency Contact SOS numbers and the emergency message have been created and stored this function is ready for use Simply press the red Emergency button on the remote band or telephone base Once pressed the AMPLI600 will automatically dial your emergency contact SOS numbers starting with number 1 If this number is busy or nobody answers within 30 seconds the AMPLI600 will dial the second emergency contact SOS number This process will continue until all 6 numbers have been dialed twice unless someone picks up the call When a person answers the emergency call they will hear the emergency message The person must press one of the keypad keys 0 9 or to confirm that the emer gency contact SOS message has been received and this will also stop the AMPLI600
4. AREA To review the new calls use the A or W keys When all new calls have been reviewed the new call LED will disappear and the screen will come back to idle state after a few seconds The total number of incoming call entries on the incoming call log will still be displayed on the screen When the incoming call log is empty if records have been deleted for example the screen will display 00 37 Use a Number from the Caller Display Log There are two ways to use numbers from the call log Firstly find the number and then lift the handset Use A or Y to access the log and scroll until you find the required number for dialling I Lift the handset or press SPKR or press Headset if headset plugged in the number will be automatically dialled I Alternatively you can lift the handset and then find the number l Lift the handset and then use A or YW to access the log and scroll until you find the required number for dialling l Press OK and the number will be automatically dialled Note You cannot use either of these methods to recall a number that displays PRIVATE or OUT OF AREA Delete a Number from the Caller Display Log Use A or Y to access the log and scroll until you find the required number for deleting Press C the T will display DEL Press C i confirm Press OK to exit 38 Delete all Numbers from the Caller Display Log Use A or to acces
5. MONITORING Remote Audio Monitoring Activate Remote Audio Monitoring Setttting the Remote Audio Monitoring Access PIN Code Using Remote Audio Monitoring OPTIONAL ACCESSORIES Headset Neckloop Shaker VOLUME AND TONE Sending Level Adjustment Receiving Level Adjustment Handset Amplifier PHONEBOOK Create a Phonebook Entry Create and Entry from the Caller Display Log 26 26 27 27 29 29 30 31 31 32 33 34 Make a Call from a Phonebook Entry 35 Delete a Phonebook entry Modify a Phonebook Entry CALLER DISPLAY Use a Number from the Caller Display log Delete a number from the Caller Display Log Delete all Numbers from the Caller Display Log Call Waiting NEW CALL MESSAGE LED Message Waiting LED TROUBLESHOOTING SAFETY INFORMATION REGULATORY COMPLIANCE GUARANTEE 35 36 37 38 38 39 39 40 40 43 44 45 48 Congratulations on purchasing your AMPLI600 telephone This is a multifunction telephone which offers features such as hands free use phonebook and caller display It also has the added benefits of send and receive amplification There are two emergency features the first allows you to call emergency contacts either using a remote band or with one touch of a button on the base The other feature is called remote audio monitoring this allows your contacts to call and speak to you without the need for you to pick up the phone Both feature are very useful in times o
6. Press MUTE Use A or to select SET PHONE Press OK Use A or to select SET RING Press OK Select desired ring tone Use A or Y to scroll through and listen to the 4 tones available Press OK to select desired ring tone Press C three times to exit or do nothing for 20 seconds and the ring type will automatically be saved ready for the next incoming call Alarm and Ringer Settings A 3 position switch located on the right side of the phone allows the settings below Ringer and strobe flash are activated Normal Setting The other two settings are only effective when an optional vibrator pad has been added N Ringer shaker and strobe flash are activated o O Ringer and shaker are activated 11 Dialling Mode The Tone Pulse is factory pre set to Tone Tone In the US all telephone exchanges now use Tone dialling If your phone does not dial out it is probably being used from an older private switch board PBX In this case theTone Pulse setting must be moved to Pulse Pulse Press Mure Use A or to select SET PHONE sae OK Use A or Y to select TONE PULSE Te OK Select TONE Press FP confirm Press C times to exit Date Time Format and setting Format You can choose between Day Month or Month Day and between 12h 24h Press MUTE Use A or to select SET PH
7. and you will need to press any of the 0 9 keys to continue otherwise the AMPLI600 will hang up 28 Headset You can also use your Ampli600 in hands free mode with an optional head set this is ideal for use with a computer screen To use the headset Connect the headset into the headset socket located at the back of your telephone l Press the headset key to get the dial tone Dial the number To answer a call press Headset key whilst the phone is ringing You can adjust the volume and tone level of calls received with the VOLUME and TONE slide buttons located on the top of the phone if func tion is active and the sending level with the 3 position switch located on the right side Neckloop Connect the neckloop into the neckloop socket located at the back of your telephone l Press SPKR or lift handset to activate the neckloop and speak into the microphone on the neckloop or handset respectively The neckloop also has a volume control To answer a call press SPKR or lift handset whilst the phone is ringing Note The Ampli600 must be connected to the mains in order to use a neck loop 29 Shaker If you would like to be alerted to incoming phone calls by a vibrating shaker you can use an optional shaker Connect the shaker into the shaker socket located at the back of your phone When an incoming call is received the shaker will be activated and
8. digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Some cordless telephones operate at frequencies that may cause interference to nearby TV s and VCR s to minimize or prevent such interference the base of the cordless telephone should not be placed near or on top of a TV or VCR and if interference is experienced moving the cordless telephone farther away from the TV or VCR will often reduce or eliminate the interference However there is no guarantee that interference will not occur ina particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help If trouble is experienced with this equipment for repair or warranty infor mation please contact our customer service staff at 248 577 5400 If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is
9. resolved Please follow instructions for repairing if any otherwise do not alter or repair any part of device except as specified Opening the equipment or any attempt to perform repairs will void the warranty Connection to party line service is subject to state tariffs Contact the state public utility commission public service commission or corporation for information If your home has specially wired alarm equipment connected to the tele phone line ensure the installation of this telephone equipment does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company or a qualified installer This equipment is hearing aid compatible 46 Sonic Alert warrants the phone against any defect in materials or workman ship for the period of one year from the date of purchase Should you experience a problem contact our customer service depart ment Be sure to save your sales receipt as proof of purchase date should you need warranty service Within a period of one year from purchase date Sonic Alert will repair or replace our discretion your phone at no cost if a defect in materials or workmanship is found If we elect to replace your phone we may replace it with a new or reconditioned product of the same or similar design Repair or replacement will be warranted for a period of 90 days or the original time on the original warranty whichever is longer The
10. voice mail services All answering machine or systems connected to the same phone number as the AMPLI600 must be unplugged or deactivated Activate Remote Audio Monitoring Press MUTE tse a or Y osea SETSOS SSCS e OK Use A or to aa AUTO TURN l Press OK Use A or Y to select ON off to deactivate I Press OK Press C twice to exit 27 Setting the Remote Audio Monitoring Access PIN Code The speakerphone will identify the PIN number for Remote Audio Monitor ing The Access PIN code is factory preset to the sequence 1234 It can be changed as follows Press MUTE Use A or to E SET SOS Te OK Use A or to PIN CODE ae OK Use C to delete existing digits I Enter your new code max 4 digits Press OK Press C twice to exit Using Remote Audio Monitoring These are instructions for your remote emergency contact caller Ensure you provide them with the remote PIN code 1 Dial as if it was a regular phone call You will hear a beep after 10 dialing tones 2 You will have 10 seconds to enter the Remote Audio Monitor Access PIN Code on your keypad the access code is 1234 unless it has been changed This turns on the speakerphone of the AMPLI600 phone and allows you to listen in and have a two way conversation 3 Every 2 minutes another beep will be audible
11. warranty does not cover accidents negligence or breakage to any parts This includes shipping damage failure to follow instructions misuse fire floods use of incompatible accessories Acts of God or failure in your phone service carrier s line service The product must not be tampered with or taken apart by anyone who is not an authorized Sonic Alert representative Tampering with the phone will void ant written or implied warranties Sonic Alert shall not be responsible for loss of time inconvenience property damage caused by your phone or any other accidental or consequential damages Warranty service is available only with proof of purchase G e 7 ActiveForever com 47 Discount Therapy Equipment Medical Equipment amp Supplies SCOTTSDALE 1 800 377 8033 PEORIA
12. GEEMARG SOUND HEAR THE DIFFERENCE Caution This telephone product is specifically designed for people with hearing difficulties and is provided with a handset earpiece volume control for individual requirements Due care must be taken by all users that the handset earpiece volume control is set to the lowest level acceptable by each respective user Care should therefore be exercised to ensure that any new users are familiar with this requirement English Espanol Fran ais CONTENTS INTRODUCTION Unpacking the Ampli600 INSTALLATION Setting Up Wall mount installation DESCRIPTION SETTINGS Ringer Volume Ringer Tones Alarm amp Ringer Settings Dialling Mode Date time format amp setting Language Setting Screen Contrast Adjustment Auto On Hook Auto screen Sizing Area amp LDS Code Setting USING THE TELEPHONE Answering a Call Making a Call Switching between Speakerphone and Handset Call Time Counter Last Number Redial Recalling Recent Numbers Deleting Recent Numbers Mute function Flash One Touch Memory Keys EMERGENCY CONTACT Create Emergency Contact SOS Numbers Create the Emergency Message Play the Emergency Message Using the Emergency Contact Telephone Testing the Remote Band Change the Remote Band Battery 6 10 11 11 11 12 13 14 15 15 16 17 18 18 19 19 19 20 20 20 21 22 23 23 24 25 25 26 26 Cancel and Emergency Contact Call 26 REMOTE
13. I600 and then slide the plate upwards until it is securely placed on the phone Once the Wall Plate adapter is installed plug the 8 inch short cord into the jack on the wall Holding the phone slightly above the mounting screws on the wall jack push the phone against the mounting screws so they are hooked into upper and lower key hole slots on the back of the phone Slowly slide the phone down until it snaps into place Connect the handset curly cord to the handset and the other end to the telephone Lift the handset if there is a dial tone the telephone is ready for use If there is no dial tone check that everything is plugged in as described above Priority memories Key to activate tone Tone reception P1 P2 P3 and volume adjustment function adjustment Aerial ye Speaker Volume Speaker volume reception adjustment adjustmen Direct memories Stop SOS SOS key emory storing key SOS key stop SOS key Hands free dialling amp amplifier Remote control Hands free Last number redial microphone Headset button Time break recall button Message waiting newcall LED Flashing incoming call Mute button indicator strobe light Additional amplifier button Clip to return to wall mount Speaker Handset cord Tone amp volume adjustment Speaker volume adjustment automatically activated each time you hang up the phone Ringer shaker strobe select mode Ringer
14. ONE Press OK Use A or Y to select DATE FORMAT Press OK Select DAY MONTH or MONTH DAY Press OK to confirm Use A or to select HOUR FORMAT I Press OK Select 12 HOUR or 24 HOUR Press OK to confirm Press C twice to exit 13 Setting Time date If you subscribe to Caller Display these parameters will usually be set automatically when you receive your first call Press MUTE Use A or to select SET TIME Press OK Use A or Y to select the desired digit Press OK to confirm and pass to next digit You will set time first then the date Press C to exit Language Setting You can choose between 16 different languages including English and French The default is American English English 1 Note Do not change to a language you cannot read or understand as it will be difficult to return to a language on screen that you do understand Press MUTE Use A or to select SET PHONE Press OK Use A or V to select SET LANGUAGE Press OK Use A or Y to select required language Press OK to confirm Press C twice to exit Screen Contrast Adjustment Your screen has a backlight that automatically switches off after 15 seconds of inactivity To decrease or increase the contrast of the backlight Press MUTE
15. Press C the screen will display DEL Press C to confirm Press OK to exit Mute Function If you wish you can speak privately to someone else in the room without your caller overhearing You will still be able to hear the caller but they cannot hear you during the mute operation During a call press MUTE The screen will display X which indicates that your voice is muted to the call and that they cannot hear you speaking Press MUTE again to resume the conversation The mute symbol will disappear from the screen 20 Flash This is used with the new services provided on digital exchanges e g the flash button can be used to disconnect a call and re establish a dial tone or switch to another caller when using services such as Call Waiting For details please contact your network operator Press MUTE Use A or to to select SET PHONE Press OK Use A or to to select REG FLASH Press OK Use A or to to select FLASH300 or FLASH600 Press OK Press C twice to exit Default in US 600ms 21 One Touch Memory Keys Your phone has a total of 11 one touch memory keys The 3 priority P1 P2 P3 memories allow you to store priority numbers in case of emergencies such as Local police station Your doctor Your neighbour There are also 8 one touch memories for frequent
16. d off turn the extra volume adjustment switch located on the rear panel of the telephone to On use the tip of a pencil or small screwdriver if necessary ON When the switch is ON the extra receiving volume and tone functions are automatically activated each time you use the phone You do not need to use the AMPLI button during any call you can temporarily switch off and on the extra volume override by pressing the AMPLI button OFF When the switch is switched OFF you will need to activate the func tion by pressing the AMPLI button in order to get use of the extra volume and tone functions This override is useful if the person using the telephone will always need the amplification setting 31 Handset Amplifier In both cases you can also boost the reception volume by an extra 12 dB by holding down the handset amplifier button located on the handset Note The button must be released while talking or it will act as a mute button Caution Exposure to high amplification levels to people without hear ing loss may cause damage to hearing 32 Create a Phonebook Entry You can store 99 entries into the phone book with the name and phone numbers of your correspondent Press MUTE Use A or V to select PHONEBOOK I Press OK Use A or V to select ADD Press OK en Enter the number 30 digits max per memory name corresponding to entered number When the number is co
17. f emergency Its is important that you read the instructions below in order to use your AMPLI600 to its full potential Keep this user guide in a safe place for future reference To use the caller display facility you must subscribe to your network provider s caller display service CAUTION This telephone product is specifically designed for people with hearing difficulties and is provided with a handset earpiece volume control for individual requirements Due care must be taken by all users that the handset earpiece volume control is set to the lowest level acceptable by each respective user Care should therefore be exercised to ensure that any new users are familiar with this requirement Unpacking the Ampli600 When unpacking the telephone you should find the following in the box 1 Telephone base unit e 1 Telephone handset e 1 Handset curly cord e 18 inch short telephone line e 1 6ft telephone line cord e 1 AC Adapter e 1 Screwdriver e 1 Wall plate adapter e 1 User guide Setting Up Connect the curly cord and the handset Remove the screw of the battery compartment using the screwdriver pro vided and open the battery compartment Insert 4 good quality alkaline batteries AAA size 1 5V type not supplied into the battery compartment located on the base of the telephone Note Do not use rechargeable batteries Do not put batteries into the household rubbish pay attention to battery regulations regarding battery dis
18. free When the phone rings press SPKR The caller s voice will be heard through the loudspeaker and they will hear your voice via the microphone near the SPKR button The speakerphone symbol will appear on the display e To end the call press SPKR again Using the inductive coupler for hearing aids e Turn your hearing aid to the T setting e Use the phone handset as usual but the inductive coupler will feed the incoming call directly into your hearing aid Note users of digital hearing aids must make sure their aids have been programmed for use with the T setting Making A Call Using the handset e Lift the handset and when you hear the dialling tone dial the number on the keypad e To end the call replace the handset Pre dialling e Key in the required number without lifting the handset e Use the C key if necessary to cancel and correct a wrong digit e Lift the handset and the number will be automatically dialled e To end the call replace the handset 18 Hands free e Key in the required number without lifting the handset e Use the C key if necessary to cancel and correct a wrong digit e Press SPKR and the number will be automatically dialled The speak erphone symbol will appear on the display e When the call is answered simply speak into the microphone located on the base e You can adjust the speaker level with the slide button located on the left side of your telephone e Toend the call press the ha
19. from dialling the next number The AMPL600 will then turn on the speakerphone automatically allowing you to speak to the emergency SOS contact 25 Testing the Remote Band You should test the emergency contact button on your remote band at least once a month Note You must warn your emergency SOS contacts that you are about to do this If the remote band does not work well from locations in which it has worked before replace the battery immediately 9see below and check that the phone s antenna is positioned correctly Change the Remote Band Battery Lift the remote band and unscrew the three small screws found on the base Lift the cover to find the battery Replace with 1 alkaline 23A 12V size cigarette lighter battery Take note and insert with the correct polarity Replace the cover Cancel an Emergency Contact SOS Call In cases of a false alarm you can press the X button on the remote band or STOP button on the phone base to deactivate the emergency contact SOS function Remote Audio Monitorin By giving an emergency contact a Monitor Access Code to your telephone it allows them to call and speak to you without you having to pick up the phone as they can switch on the speakerphone remotely This may be useful for them if a situation arises where they have become worried about 26 you or after they have called for help IMPORTANT This feature will not work with telephones attached to an swering machines or using
20. ing when your tele phone number is called In most but not all areas the sum of the REN s of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company to determine the maximum REN for your calling area If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your rights to file a complaint with the FCC if you believe it is necessary The telephone company may make changes in its facilities equipment operation or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service This equipment may not be used on coin service provided by the tele phone company Connection to party lines is subject to state tariffs This equipment is hearing aid compatible Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 45 NOTE This equipment has been tested and found to comply with the limits for a Class B
21. level adjustment Sending volume adjustment Screen example On hook position Minutes Power network icon Hours Day Month Cancel key Validation key Up down keys OK button is used to confirm action or a choice on the screen A VY UP DOWN arrow buttons are used to high light or scroll through the menu C button is used to cancel or confirm an action entry or clear a stored Caller ID call Screen display Your CL600 has a screen with different icons which help you to use the telephone The telephone is supplied by battery battery indicator alagi The telephone is powered by AC adapter WHE stm Memory storing is required u Screen contrast level Mute is activated Speakerphone is activated Precede the CID call record number To show new records 10 Rear Connection Shaker socket 1 Tone amp volume ON OFF switch Adaptor socket Neckloop socket 1 Only Geemarc reference H Line cord socket Classified TNV 3 according to EN60950 standard Classified hazardous voltage according to EN60950 standard Important Only Adaptor with Geemarc reference can be con nected to the CL600 sockets 1 Optional accessories Ringer Volume The ringer volume can be adjusted as high as 95 dB A switch located on right side allows the ringer to be switched to OFF LOW HIGH Your telephone comes with the ringer switched to High Ringer Tones
22. ly used numbers To store a number Lift the handset Press PROG Dial the number you wish to store checking on the display that you have keyed it in correctly 30 digits per telephone number allowed Press the one touch key button Priority or Memory dial where you wish to store it The screen will display SAVE OK Note Numbers will be lost after a few hours if you disconnect your phone Dialling stored Numbers Lift the handset or press SPKR or press Headset if headset plugged in Press the appropriate one touch memory key and the stored number will be dialled automatically There is an index card located under the base of your phone for you to make a list of which numbers are stored under which one touch memory key 22 If there is an emergency and you require help the AMPLI600 allows you to call for help effortlessly In order for this facility to work you must preset your emergency contact SOS numbers up to 6 telephone numbers and record an emergency message that will be heard by the people you call The AMPLI600 can hold up to 6 emergency contact SOS telephone num bers 18 digits per telephone number Ensure that you have discussed and agreed that you can use people s telephone number as an emergency contact SOS number Good examples of telephone numbers to use would be those of relatives neighbours or friends The friend relative or neigh bour you cho
23. nds free button again Switching between Speakerphone and Handset To stop using speakerphone during a call simply lift the handset To activate speakerphone during a call press SPKR and replace the head set on the cradle at the same time Hands free calls can also be made using an optional headset see Optional Accessories chapter Call Time Counter The call time counter will be displayed a few seconds after the phone num ber is connected and starts ringing To stop the time counter press C If you press C twice the time counter will be reset to 0 Last Number Redial Lift the handset or press SPKR or press Headset if headset plugged in Await the dial tone and press REDIAL The previously dialled number will be automatically redialled 19 Recalling Recent Numbers You can call back any of the last 30 numbers dialed Press OK Screen will display DIALLED the last number dialled total number of numbers dialled plus time and date of displayed number Use A or V to to select the number you wish to dial Lift the handset or press SPKR or press Headset if headset plugged in the number will be automatically dialled Deleting Recent Numbers Press OK Screen will display DIALLED the last number dialled total number of numbers dialled plus time and date of displayed number Use A or to to select the number you wish to delete
24. on e Check that the phone is in the ON HOOK position No dial tone e Make sure that the telephone line cord is plugged in correctly and is not damaged e Connect another telephone to the telephone PTT socket or move your telephone to another socket to track if the failure is coming from your telephone or your PTT socket e There may be too many communication devices connected to a single telephone line e g another telephone modem or facsimile machine Contact your network provider for help in calculating the limit for your home or business line No number is displayed when the telephone rings e Please contact your telephone network provider to obtain the caller display service or ensure that it has been activated if you have sub scribed already e Even if you have subscribed to caller display if the caller does not want to show their number the display will show Private number or if the 42 call is from an area not providing caller display Unavailable number will be displayed e It could be a call from a PBX Caller display may not work properly if the telephone is connected to a PBX No response on LCD display e f you have experienced a power failure the batteries may become weak If the power is restored and the LCD display still does not re spond then replace the batteries with new ones No Strobe Ringer and or bed shaker will not activate e Make sure the strobe and or shaker switch is turned ON e Make sure the Bed Shaker is pl
25. ose must have a touchtone phone service and a phone that will generate touch tone codes Do not use the emergency services as emergency contact SOS numbers Note We suggest that both the Remote Audio Monitoring amp Auto On Hook features of the AMPLI600 are ON to ensure the Emergency Contact Feature works correctly Create Emergency Contact SOS Numbers Press MUTE I Use A or to select SET SOS Press OK l Use A or to select SET SOS NUMBER 1 Press OK Enter the emergency connect SOS number you can use the C key to delete previousdigit i Press OK to confirm I To program another emergency contact SOS number select SOS NUMBER 2 or 3 4 5 6 from the menu and do the same as above I Press C three times to exit 23 In order to change an emergency contact SOS number simply do as above but select the emergency contact SOS number you wish to change from the menu then type over the existing number NOTE If you only want to program one phone number you should store this number in all six of the memory locations Create the Emergency SOS Message This is the message that the emergency contact will hear if the call is an swered The message can be up to 10 seconds long Press a Use A or to See SET SOS Press OK Use or Y to SOS SOUND Press OK Record your emergency contact SOS message by speaking
26. posal Replace the battery cover Desk Installation Connect the 6ft line cord to the jack located at rear of telephone then con nect the plug to the telephone wall socket Connect the power supply to the jack located on the back of the telephone then plug into the wall socket Please choose a socket near your telephone socket to enable you to unplug the mains power quickly in case of a prob lem Lift the handset if there is a dial tone the telephone is ready for use If there is no dial tone check that everything is plugged in as described above Note Mains power is required to power the multifunction features of the telephone Fit 4 x AAA sized batteries in order to save and use stored numbers in case of power failure Without mains or battery power the telephone can still be used to answer calls or to manually dial out calls but all stored numbers will be lost Wall Mount Installation Slide the handset hanger bar out and rotate it 180 degrees Slide it back into place The hook will now point up This ensures the handset will not fall out of the cradle when it is mounted on the wall Plug the 8in short phone cord into the telephone jack on the AMPLI600 now run the phone cord under the wall plate adapter and through the opening Insert the Wall Plate adapter Hold it so that the raised mounting pins line up with the phone s keyholes on the AMPLI600 Once the holes are lined up push the wall plate adapter in towards the AMPL
27. r 3 seconds to confirm the proposed Caller Display name Press C to exit 34 Make a call from a Phonebook Entry Press MUTE Use A or to select PHONEBOOK Press OK Use A or to select REVIEW Press OK Use p or q to select number you wish to dial You can also get quick access to a phonebook entry by entering the first letter of the name Lift the handset or press SPKR or press Headset if headset plugged in the number will be automatically dialled Delete a Phonebook Entry Press MUTE Use A or V to aa PHONEBOOK OK Use A or to ae REVIEW as OK Use A or V to select ie you wish to delete Press C the screen will display DEL Press C ts confirm Press OK to exit Modi 36 a Phonebook Entr Press MUTE Use A or to select PHONEBOOK Press OK Use A or V to select REVIEW I Press OK Use A or to select number you wish to modify Press and hold OK until the last number digit flashes Press C to modify the number and insert new number Press OK You can now modify the name Press the C key to delete a letter Press OK for 3 seconds to confirm the new entry then C to exit The features described in this section are only available if you subscribe to a Caller Display se
28. roduct to fire or other hazardous conditions Unplug your phone from the telephone socket during thunderstorms be cause it could damage your telephone Your guarantee does not cover thunderstorm damage Do not use the telephone if there is a gas leak Any spark that might be created by the electrical contacts found in the telephone could ignite a large amount of leaking gas The telephone is designed for working within a temperature range of 5 C to 45 C 44 This equipment complies with Part 68 of the FCC rules and the require ments adopted by the ACTA On the bottom of this equipment is a label that contains among other information a product identifier in the format US AAAEQ TXXXX If requested this number must be provided to the telephone company All applicable certification jacks Universal Service Order Codes USOC for the equipment is provided i e RJ11C in the package with each piece of approved terminal equipment Aplug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and re quirement adopted by the ACTA A compliant telephone cord and modular plug is provided with this product It is designed to be connected to a compatible modular jack that is also compliant See installation instructions for details The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices r
29. rrect press OK to confirm and enter the see table below Select the desired letter by a pressing on the corresponding key When the name is correct press OK for 3 seconds to confirm the Number and Name storage and press C to exit You can use this table or the letters printed on the keypad to help you create a phone book entry Key gt OONDOAWDNDN Characters 1 2 lt 1 ABCabc2 DEFdef3 4 GHIghi4 JKLjkI5 MNOmno60 PQRSpqrs 7 TUVtuv8sU WXY Zwxyz9 0 amp 33 Example To input the letter b press the 2 key 5 times The letter b will show in the display To insert a space press on the OK key twice If the next letter is the same as the previous letter or located on the same key press first on the OK key to move and select the desired letter Use the C key to delete a wrong number or letter Note If you wish to insert a pause in the stored number press the REDIAL key whilst entering a P will be displayed on the screen Create an Entry from the Caller Display Log You can store 99 entries into the phone book with the name and phone numbers of your correspondent Use A or to display incoming calls on the screen Use A or Y to select the number you wish to store in the phonebook Press and hold OK until the last number digit flashes You can now modify or enter the name of the caller as shown above or press and hold the OK key fo
30. rvice from your network provider Caller Display means you can see who is calling on your LCD display pro vided the number is not withheld unavailable or is an international call When your telephone rings the time date the caller s phone number and name and a count number 1 99 is displayed on the LCD display The most recent call will have the highest count Every received call that is not answered is stored in the call log and the new calls count together with total calls count displayed on the standby screen increases by one The LCD display will return to standby 10 seconds after the last ringing burst if the call is not answered This new call will also activate the new call indicator to blink This will continue to blink until the new calls are reviewed and saved deleted in the call log Note Area code and LDS code must be set correctly see Settings chapter for the telephone to recognize and dial calls from the Caller Display log If the caller does not wish to show his phone number or his name the screen will display PRIVATE NAME or PRIVATE CALLER depending on whether simply name or name and number are being withheld If UNKNOWN NAME or UNKNOWN CALLER are displayed if means the telephone company does have information about either the name or the name and telephone number If the number is unknown from the telephone centre international incoming call for example the screen will display OUT OF
31. s the log Press and hold C until the ae displays ALL DEL Press C F confirm Press OK to exit Call Waitin With this service you are made aware that a new call is coming through when you are in conversation You can take this call and switch between callers To use this feature you must have subscribed to this service with your network provider Press MUTE l Use A or to select SET PHONE Press OK Use A or Y to select CALL WAITING re OK Use A or Y select ON Press OK I Press C twice 39 Call Waiting in Practice When you are in conversation with caller no 1 their name and number will be displayed on the screen A beep tone will be heard when a second call is incoming and their name and number will be displayed on the screen If you chose to answer the call press FLASH or the phone hook button to transfer Note If you don t answer the second call the number will be recorded into the incoming call log and you will be able to call them back later For more information about subscribing to Call Waiting contact your net work provider 40 The red LED on the front of the phone will flash to indicate missed calls To cancel the flashing light review your new calls Simply use A or to access the log and scroll through all the new calls Alternatively you can delete the log of unreviewed calls Use A or to acces
32. s the log Press and hold C until the screen displays ALL DEL Press C k confirm Press ak to exit If you do not subscribe to caller display or message waiting service simply press A or Yonce To turn off this feature set the MSG switch on the base of the phone to OFF New calls will still be indicated with N on the screen but the LED will not flash Message Waiting LED If you are connected to certain type of switchboards you may get amessage waiting voicemail service MSG WAITING will be displayed on screen and the red LED will be lit continuously You must retrieve your message in order to turn the red light off 41 No display e Make sure that the power adaptor is plugged in correctly and is not damaged e Make sure the batteries are inserted correctly e Make sure that the batteries are fully charged Telephone does not ring e Make sure that the telephone line cord is plugged in correctly and is not damaged e Connect another telephone to the telephone PTT socket or move your telephone to another socket to track if the failure is coming from your telephone or your PTT socket e There may be too many communication devices connected to a single telephone line e g another telephone modem or facsimile machine Contact your network provider for help in calculating the limit for your home or business line e Check that the button ringer on the right side is not set to OFF posi ti
33. ugged in correctly No amplification e 1 Check to see if the AMPLI amplify button is ON You should see the red light There is Interference on the line e A filter may be required for homes with DSL line There is a red light that continues to flash e You have un reviewed Caller ID Call Waiting information or missed a Call No Numbers in memory e No number stored in that memory button e f your phone has been disconnected for a few hours the numbers stored will be lost Emergency Connect button is not working e There may be a phone off the hook somewhere in your home e Check the Auto On Hook Feature e The remote band s battery is low or is not installed properly e Check the antenna on base 43 General Only use the correct authorised power supply with the product Do not open the unit except to replace the batteries Contact the helpline for all repairs Never dispose of batteries in a fire There is a serious risk of explosion and or the release of toxic chemicals Cleaning Clean the telephone with a soft cloth Keep the base and handset charging contacts clean Never use polishes or cleaning agents they could damage the finish or the electrics inside Environmental Do not expose to direct sunlight Always ensure there is a free flow of air over the surfaces of the tele phone Do not place any part of your product in water and do not use it in damp or humid conditions e g bathrooms Do not expose your p
34. vibrate while the phone rings One of the shaker settings must be selected using the 3 position switch located on the right side of the phone See Settings chapter For these optionals accessories consult the retailer see contact details at the end of this manual 30 Sending Level Adjustment If your voice is quiet or the person you have called has difficulty hearing you can increase the sending level volume with the switch located on the right side You can also decrease the sending volume if required There are three levels Min Normal and Max outgoing volume up to 12dB Receiving Volume and Tone Adjustment You can increase the receiving volume and adjust the receiving tone ac cording to your own hearing requirements The AMPLI button allows extra receiving and tone functions to be activated during the conversation in an ad hoc fashion When the function is activated the red light to the left of the button is lit Use the TONE and VOLUME slider buttons to adjust the level according to your own hearing requirements When AMPLI is on the receiving volume adjustment is 15 30dB The tone control allows you to either boost low or high frequency range When AMPLI is off the receiving volume adjustment is 0 15dB The tone control cannot be used When the call is finished the telephone will reset to standard mode i e AMPLI turned off Extra Volume Adjustment Switch In order to override the standard setting i e AMPLI switche
Download Pdf Manuals
Related Search