OWL Intuition Room Sensor
Contents
1. 14 2 Save Energy Limited 2013 Additional Installation Information Room Sensor Factory Reset Delete Network OWL Pairing You can factory reset the Room Sensor by pressing both the Standby and Away buttons together for a minimum of 10 seconds The 3 LEDs will start flashing indicating that it is in pairing mode Refer to Getting Started with OWL Intuition Network Gateway guide if you need to factory reset the Network OWL Room Sensor Relay Unit Pairing Mode You can place the Room Sensor into Relay Unit pairing mode by pressing all 3 buttons together for a minimum of 4 seconds The 3 LEDs will start flashing indicating that it is in pairing mode If the Room Sensor is already paired to a Relay Unit pressing the 3 buttons will delete that pairing Refer to Relay Unit Installation Instructions for further information Safety Switch The Room Sensor is fitted with a safety switch that is automatically activated when the front of the Room Sensor is removed from the backplate Safety switch activation will im mediately turn the heating off and the web dashboard will show an appropriate warning message The Room Sensor MUST be installed onto the special backplate supplied other wise the safety switch will not operate and the Room Sensor will not work 2 Save Energy Limited 2013 15 BEFORE Typical Existing Wired Room Thermostat Installation Boiler or Wiring Centre Existing wiring Room Thermostat typicall2. y OWL Unrtuition Heating Control Room Sensor rer 3c or reH 3C Installation Instructions Room Sensor to replace existing wired room thermostat Alternatively can be paired to optional Relay Unit to allow wireless connection to the boiler wiring centre location Support for up to 4 separate heating zones Provides programmer time clock functionality Requires Network OWL to operate cE fire Co Bul LE 2 x AAA Safety Cover alkaline battery Room Sensor 2 Save Energy Limited 2013 1 Backplate Introduction This Room Sensor is a part of the OWL Intuition range of cloud connected monitoring and control products Its operation is dependant upon being paired to the broadband Internet connected Network OWL supplied separately The Room Sensor provides both room thermostat and programmer time clock functionality Basic day to day user operation changes can be made using the three buttons Addition ally there is comprehensive yet intuitive and easy to use control via the OWL Intuition web dashboard Accessible from any Internet connected computer anywhere in the World iPhone and Android smartphone apps are also available for free download It is recommended that this product is installed by a suitably qualified heating engineer plumber or electrician Please read the Safety Information section of this document before proceeding 2 2 Save Energy Limited 2013 Version Information This Room Sensor is b
3. The OWL Intu ition system will support up to 4 heating zones For additional Room Sensors simply repeat these instructions for each one required The web dashboard will automatically update the Heating widget with the additional device when you next log in Network OWL installed and online The Network OWL should already be installed Refer to the Network OWL Getting Started Guide for guidance if required Check that it is powered up and connected to the OWL servers the top green LED should be flashing in a triple blip pattern 1 It is essential that the Network OWL is running the latest released version of firmware available at least Version 2 2 Please log in to the OWL Intuition web dashboard at https www owlintuition com this is a secure connection 2 Click on the Devices menu The Network OWL will appear in the list of devices Click on Network OWL image to open a new window If an upgrade is required an Update Device button will be visible Click on this button then wait for approximately 5 min utes for the upgrade to complete You should check that the upgrade was successful before proceeding by repeating this instruction 4 2 Save Energy Limited 2013 Other Steps Before Installing 1 Pair Room Sensor with Network OWL a Put the batteries into the Room Sensor The 3 LEDs will start flashing together indicating that the Room Sensor is ready to be paired F Power down the Network OWL by removing d the powe
4. amp Conditions OWL Intuition Web Dashboard Heating and Time Clock widgets The preset heating Comfort Time Clock settings are shown in the table opposite These can be modified using the OWL Intuition web dashboard a On the Heating widget click on the Clock icon This opens the Heating Time Clock widget Select the day you wish to amend then click an option on the line you wish to amend i Pencil icon to edit the line ii Cross icon to delete the line Amend details within the Edit box as required then click on the Tick icon to update the table To add a new line simply fill in the Add box with the required details and click on the Tick icon Preset Heating Comfort Time Clock Settings Monday to Friday Start Time End Time Temperature 07 00 08 30 18 C 16 30 22 30 20 C Saturday amp Sunday Start Time End Time Temperature 07 30 10 00 18 C 16 30 22 30 20 C Note Outside of these preset heating Comfort periods the Room Sensor will be in Standby mode 15 C configurable When you are happy with your changes you can use the Copy Current Day feature to quickly duplicate to other days 2 Save Energy Limited 2013 f IMPORTANT When you have finished making changes you must save them to your Network OWL by clicking on the Save To Network OWL button 5 Pair Room Sensor with Relay Unit Intuition cw wireless installations only If
5. Manuals web dashboard lower right Customer Support If you have any further questions please check our frequently asked questions at http www theowl com faqs html You can also email us at customer services theowl com please ensure you state your Network OWL MAC ID 2 Save Energy Limited operate a policy of continuous development and improvement therefore the content of this document is subject to change without notice Issue 2 RBT 3C RBH 3C Installation Manual 24 2 Save Energy Limited 2013
6. called Comfort Periods OWL In tuition will intelligently calculate what time to switch the boiler on and off to maintain the target temperature for the whole of the Comfort Period Each day of the week can Property EPC Energy Efficiency Rating Rating Score Description A 92 Exceptional B 81 91 Above Average C 69 80 D 55 68 UK Average E 39 54 F 21 38 Below Average G 1 20 be programmed with up to 10 different Comfort Periods 2 Save Energy Limited 2013 ONNE Lituition Settings Devices Messages Shop Logout 21 Partly Cloudy Humidity 64 Wind 13 mph Cloud Cover 39 Status Until Required Amb Hum 22 6 C Standby 16 30 Today 15 0 C idity 61 2 Lf IE l Network OWL System Online Time Clock Day Sunday eA Tuesday Wednesday Thursday Friday Saturday Start Time End Time Temperature Options 2 16 30 22 30 20 0 C 20 9 amp Options Copy Current Day To All Days 7 _ Save To Network OWL Download From Network OWL Please Note Times should be set for your Comfort periods when the set temperature should be maintained OWL Intuition will automatically calculate and apply Warm Up and Cool Down times to help reduce your energy consumption 2013 2 Save Energy Limited v1 5 2 Save Energy Limited 2013 Support amp Manuals Privacy Policy Terms
7. this Room Sensor is being installed for a wireless connection to an OWL Intuition Relay Unit RMx 6C then please follow the Relay Unit Installation Instructions sup plied with that device 2 Save Energy Limited 2013 Installing the Room Sensor The Room Sensor should be located on an internal wall approximately 1500mm above floor level you must use the backplate provided It should be positioned away from draughts direct heat and sunlight The backplate is suitable for direct wall mounting using two wood screws No 6 x 1 or M3 5 x 25mm into correctly sized wall plugs if required Alterna tively mount on to a single gang flush wiring box complying with BS4662 using two M3 5 screws 1 Check Signal Strength With the Room Sensor at the chosen installation location you should now check the signal strength icon shown on the web dashboard Heat ing widget The signal should be at least 2 bars and preferably more Try moving the Network OWL closer to the Room Sensor if you have a signal strength problem Ensure there will be enough space to allow easy screwdriver access to the two cap tive screws located at the base of the backplate Electrical Connections If in any doubt whatsoever do not continue but consult a qualified electrician or heating engineer WARNING ISOLATE THE MAINS SUPPLY BEFORE COMMENCING INSTALLATION For existing installations remove the old room thermostat to expose the wiring back to the boiler Check th
8. attery powered with a latching relay It has 3 control buttons Com fort Standby and Away with associated LED indicators Device code RBT 3C is fitted with a digital temperature sensor Device code RBH 3C is fitted with a digital temperature and humidity sensor Installation Configurations Supported This Room Sensor can be used in several ways to suit various heating control needs Heating Type Combi boiler Conventional central heating and System boiler Room Thermostat Type Wired connection to boiler and Wireless connection to boiler when paired to Relay Unit RMx 6C Multi Heating Zone Control A single OWL Intuition system can support up to 4 Room Sensors one for each heating zone in either a wired and or wireless configuration paired to Relay Units Additionally a single Relay Unit can be paired to multiple 8 Room Sensors and optional Tank Sensors for Hot Water control This flexibility enables OWL Intuition to be used to control heating and hot water systems that are Building Regulations Part L compliant and beyond Maximum Number of Devices Every OWL Intuition device within a single system e g Room Sensor Tank Sensor Relay Unit and Electricity Transmitter must be paired to the Network OWL The Network OWL supports up to a maximum of 10 devices 2 Save Energy Limited 2013 3 Installation Instructions Single or multiple heating zones If this is a single zone heating system then simply follow these instructions
9. e wiring at both ends to correctly identify which wire is Live and which is Switched Live 2 Save Energy Limited 2013 Mains Supply L N E OWL Room Sensor Green Yellow Remove Link Switched Live Typical OWL Intuition c Wired Room Sensor Installation 2 Save Energy Limited 2013 11 12 For new installations run a new cable between the boiler and chosen Room Sensor Location The recommended cable size is 1 0mm See diagram opposite Ensure that the Live feed to the Room Sensor is correctly fused 3A or 5A maximum This protection is normally provided by way of a fused spur powering the heating system Fix the backplate Offer the backplate supplied to the wall in the position where the Room Sensor is to be mounted with the cable through the central aperture of the backplate and mark the fixing positions through the slots in the backplate Drill and plug the wall then secure the plate into position The slots in the backplate will compensate for minor misalignment of the fixings Wiring All necessary electrical connections should now be made e The Room Sensor is double insulated and does not require an earth connection e An earth connection block is provided on the backplate for terminating any cable earth conductors e Earth continuity must be maintained and all bare earth conductors must be sleeved e If one of the existing wires is a Neutral supply then this should be parked on the terminal labell
10. ed N e Ensure that no conductors are left protruding outside the central space enclosed by the backplate e Refer to the diagram and table shown below for the wiring arrangement for a typical heating system This diagram is schematic and should be used for guidance only 2 Save Energy Limited 2013 e Y Plan and S Plan wiring diagrams are supplied with the OWL Intuition Tank Sensor product They can also be downloaded from the Intuition web dashboard under Support amp Manuals e Please ensure that all installations comply with the current IEE regulations e Please consult the boiler manufacturers installation instructions before making these connections and note that a link may need to be removed when connecting external controls Fit Safety Cover Check all of the wiring is safely attached to the appropriate back plate terminals and the screws are tight Then fit the Safety Cover by clipping it into place over the wiring terminals Complete the installation by mounting the Room Sensor to the backplate To do this engage the Room Sensor on the lugs at the top of the backplate then carefully swing the Room Sensor down and push it carefully back into its plug in terminal connectors Locate over the captive screws at the base of the backplate and tighten them so that the Room Sensor is locked into position Existing Programmer Time Clock any existing programmer or time clock is now redundant You should either program it t
11. ely and correctly please read the warnings amp safety precautions below before installing your OWL Intuition Room Sensor Isolate the mains power supply to the heating appliance that the Room Sensor will be connected BEFORE commencing any wiring work If you are in any doubt about the Room Sensor installation whatsoever DO NOT at tempt to install but consult a qualified electrician or heating engineer Before attempting to fix the backplate to the wall you must ensure that there are no electrical cables or pipes that will be damaged drilling the fixing holes Do not immerse the unit in water or other liquids If you spill liquid over it dry it immediately with a soft cloth Do not use or store the product in conditions that could adversely affect the product such as rain snow desert and magnetic fields Do not subject the product to excessive force shock dust temperature or humidity Keep the product away from heat sources radiators stoves heaters etc Do not use the product in or near water or in high moisture areas such as bathrooms Do not tamper with the product s internal components This invalidates the warranty Do not attempt to repair the product yourself Contact the retailer or Customer Services if your product requires servicing If the equipment is used in a manner not specified in this manual the protection provided by the equipment may be impaired Take care when handling all battery types Batteries can cause inju
12. o be permanently on 24 7 or prefer ably remove it ensuring that the two wires it was switching are safely electrically linked together preferably by installing a link wire within the boiler Please check boiler manufacturers wiring instructions for further details Finally check that the Room Sensor is functioning correctly and switching the boiler 2 Save Energy Limited 2013 13 on and off correctly A simple test for this is to press and hold the Comfort button OWL Intuition c Heating Control Room Sensor Backplate Wiring Terminal Description Neutral Not used may be used to park unused neutral wire Live Not used may be used to park unused live wire Common terminal of Room Sensor latching relay Not used Heat Satisfied Normally closed terminal of Room Sensor latching relay Call for Heat Normally open terminal of Room Sensor latching relay IF alwelrfelrj2 Earth continuity connection for 5 seconds This will activate the Boost mode and turn the boiler on Check that the web dashboard Heating widget is now showing that the Boost is activated and the boiler is running Red glow around house icon at top of Heating widget Handover Please ensure you handover this document to the householder and direct them to the Heating amp Hot Water Control User Manual available for download by click ing on Support amp Manuals on the web dashboard lower right
13. r connector Then after 10 seconds re insert the power connector into the Network OWL and wait The 3 LEDs on the Room Sen sor will stop flashing indicating that it is now paired to the Network OWL Now wait until the Network OWL is connected to the OWL servers the top green LED should be flashing in a triple blip pattern Log in to the OWL Intuition account at https www owlintuition com this is a secure connection You will then see the OWL Intuition web dashboard Soon a message box will pop up indicating that a new device has been detected and requesting you to log out and log back in When you log back in you will now have a Heating widget within your web dash board 2 Save Energy Limited 2013 9 2 Configure Account Settings Select the Settings menu Select an appropriate Energy Performance Certificate EPC rating for this property Enter the actual EPC rating if you have one if not just estimate how you would rate the energy ef ficiency of the property on the A to G scale below Be sure to click the Save button before closing the window 3 Configure Heating Settings You can make any necessary changes to the various Heating settings by clicking on the gear wheels icon on the grey Heat ing widget title bar 4 Configure Time Clock The Heating Time Clock defines the periods during which the home is automatically heated and to what temperature These periods are
14. rantee from date of purchase you find that the equipment is not working properly you may return it to us and we will replace or at our discretion repair it free of charge 2 Save Energy Limited will not accept any liability for defects arising from fair wear and tear accidental or wilful damage misuse or failure to follow product or safety instructions If you return any equipment as faulty 2 Save Energy Limited reserves the right to test the equipment and if found to be in perfect working order to return it to you In this event 2 Save Energy Limited reserves the right to charge for any testing or postage costs incurred This does not affect your legal rights relating to equipment which is faulty Warranty conditions only apply where Proof of Purchase is provided To return OWL Intuition product contact customer services theowl com to report the issue and reason for returning your product 2 Save Energy Limited will issue you a form and reference number Once we have received the completed form and proof of purchase we will commence the returns process 22 2 Save Energy Limited 2013 SPECIFICATIONS Room Sensor RBT 3C and RBH 3C Samm x Samm x 37mm Thermoplastic fame retardant Relative humidity 25 to 95 non condensing 2 Save Energy Limited 2013 23 For details on using your new OWL Intuition heating controls please download the Heating amp Hot Water Controls User Manual document by clicking on Support amp
15. ries burns or 2 Save Energy Limited 2013 damage to property if they come into contact with conducting materials heat corrosive materials or explosives Remove the batteries before storing the product for extended periods Only use fresh batteries Do not mix new and old batteries Do not dispose of old batteries as unsorted municipal waste only do so in accordance with your local waste disposal regulations e When disposing of this product do so in accordance with your local waste disposal regulations GARING FOR YOUR PRODUCT Before cleaning remove the Room Sensor from the backplate and remove the batteries e Usea lightly dampened cloth Do not use liquid or aerosol cleaning agents benzene thinners abrasive or corrosive materials Do not scratch hard objects against the product Do not leave discharged batteries in the product COMPLIANCE The CE marking certifies that this product meets the main requirements of the European Parliament and Council Directive 1999 5 EC A copy of the signed and dated Declaration of Conformity is available on request OWL Intuition products are manufactured to ISO 9001 Quality Assurance Standards 2 Save Energy Limited 2013 21 WARRANTY INFORMATION 2 Save Energy Limited guarantees that OWL Intuition products will work for a minimum period of 24 months from date of purchase and that it will be free from defects in materials workmanship or design If during this limited 2 year period of gua
16. y located in Hall or Lounge Programmer Timer Room Thermostat 16 2 Save Energy Limited 2013 AFTER Typical OWL Intuition c Wired Room Sensor Installation e 1 Wireless Pairing Broadband Boiler or Wiring Centre Router Existing wiring y Option 1 Remove existing Programmer Timer and link inputs Option 2 Retain existing Programmer Timer and program to always on RBx 3C Room Sensor typically located in Hall or Lounge 2 Save Energy Limited 2013 17 BEFORE Typical Existing Wireless Room Thermostat Installation Boiler or Wiring Centre Existing wiring with mains power feed Wireless Relay Unit ypically located next to Boiler or Wiring Centre Room Thermostat Programmer typically located in timer Wireless i Hall or Lounge Relay Unit Thermostat 18 2 Save Energy Limited 2013 AFTER Typical OWL Intuition c Wireless Room Sensor Installation 1 Wireless Pairing Broadband Router Centre Existing wiring with mains power feed Option 1 Remove existing Programmer Timer and link inputs Option 2 Retain existing Programmer Timer and program to always on C RMx 6C RBx 3C Mains powered Relay Room Sensor Unit typically located next typically located in to Boiler or Wiring Centre Hall or Lounge 2 Save Energy Limited 2013 19 SAFETY INFORMATION To ensure that you use your product saf
Download Pdf Manuals
Related Search