Dual U-BR1TE Module User Manual
Contents
1. An asterisk is present when a CRC error has been detected on the U interface ACT An asterisk is present if an NT1 is communicating with the ISDN switch 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 3 3 Chapter 3 Operation T1 STATUS LOOP MONITOR PORT CONFIG There are three information fields SYNC CRC and ACT See Figure 3 4 An asterisk indicates an item is active Figure 3 4 T1 Status Display SYNC An asterisk is present if the U interface has achieved syn chronization to the T1 carrier CRC An asterisk is present when a CRC error has been detected on the T1 interface DS0s carrying U BRITE data only ACT An asterisk is present if an NT1 is communicating with the ISDN switch ESZXXX Reports the maximum number of errored seconds on the U interface Errored seconds are considered to be sec onds in which the U interface was not synchronized or seconds in which at least one CRC error was detected on the U interface This count can be set to zero by pressing shift clear when the cursor is at this menu item PoRT CONFIG a submenu of TSU 100 120 600 main menu item CONFIGURATION is used to configure the Dual U BRITE The submenu items shown in Figure 3 5 on page 3 5 are used to configure the parameters 8 4 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 3 Operation 1 SERVICE 2 CONFIG 7 PORT CONFIG 12 UBR1TE 2 ZBS 3 MODE 4 WAK2. 3 NEW PASSCODE 4 5 Figure 3 1 TSU 100 Main Menu DUAL U BR1TE MENU ITEMS The Dual U BR1TE menus are accessed from and operate the same as menus for the TSU 100 120 600 The Dual U BRITE items are submenu choices of those four main menus as shown in Figure 3 1 For information on FAC TORY RESTORE and RUN SELF TEST see TSU Features used with Dual U BRITE Options on page 3 9 The Dual U BRITE menu items are as follows e PORT STATUS PoRT CONFIGURATION PoRT UTILITY PORT TEST 3 2 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 3 Operation PORT STATUS PORT STATUS a submenu of TSU 100 120 600 main menu item STATUS displays active status information about the Dual U BRITE interface When PORT STATUS is displayed place the cursor on it and press Enter to display the first available port Scroll to select 1 1 U BR1TE and press Enter to activate either of the submenus shown in Figure 3 2 1 NI PERF REPORTS STATUS 2 NI ERRORS 3 ACTIVE ALARMS 4 VIEW HISTORY 1 LOOP STATUS 5 PORT STATUS i UBR1TE 2 T1 STATUS 6 REMOTE PORT 3 LOOP MONITOR 7 CLEAR PORT ALM Figure 3 2 PORT STATUS Submenus LOOP There are three information fields SYNC CRC and ACT STATUS See Figure 3 3 An asterisk indicates an item is active Figure 3 3 Loop Status Display SYNC An asterisk is present if the U interface has achieved syn chronization CRC
3. Donotuse this product near water such as near a bathtub wash bowl kitchen sink laundry tub in a wet basement or near a swimming pool 2 Avoid using a telephone other than a cordless type during an electrical storm There is a remote risk of shock from lightning 3 Do not use the telephone to report a gas leak in the vicinity of the leak 4 Useonly the power cord power supply and or batteries indicated in the manual Do not dispose of batteries in a fire They may explode Check with local codes for special disposal instructions WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within five years from the date of shipment if it does not meet its published specifications or fails while in service For detailed warranty repair and return information refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure Return Material Authorization RMA is required prior to returning equipment to ADTRAN For service RMA requests or further information contact one of the numbers listed on the back page of this manual vii LIMITED PRODUCT WARRANTY ADTRAN warrants that for five 5 years from the date of shipment to Customer all products manufactured by ADTRAN will be free from defects in materials and workmanship ADTRAN also warrants that products will conform to the applica ble specifications and drawings for such products as contained in the Product Manual or in ADTRAN s internal speci
4. RMA number clearly on the package below address and return to the following address ADTRAN Inc CaPS Department 6767 Old Madison Pike Progress Center Building 6 Suite 690 Huntsville AL 35807 RMA
5. User Manual A 1 Appendix A Dual U BR1TE Option Card Menu Tree A 2 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Appendix B Dual U BR1TE Failure Messages FAILURE MESSAGE AT POWER UP The following messages indicate a probable component failure on the Dual U BRITE Card E01 EPROM CS EPROM checksum error E02 RAM DATA Data Bus Failure E03 RAM ADDR Address Bus Failure E04 RAM CELL Ram Cell Failure 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual B 1 Appendix B Dual U BR1TE Failure Messages B 2 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Product Support Information Pre Sales Inquiries and Applications Support Please contact your local distributor ADTRAN Applications Engineering or ADTRAN Sales Applications Engineering 800 615 1176 Sales 800 827 0807 Post Sale Support Please contact your local distributor first If your local distributor cannot help please contact ADTRAN Technical Support and have the unit serial number avail able Technical Support 888 AADTRAN Repair and Return If ADTRAN Technical Support determines that a repair is needed Technical Sup port will coordinate with the Customer and Product Service CaPS department to issue an RMA number For information regarding equipment currently in house or possible fees associated with repair contact CaPS directly at the following num ber CaPS Department 256 963 8722 Identify the
6. cord The customer should be aware that compliance with the above limitations may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian main tenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommu nications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connec tions of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas x Users should not attempt to make such connections themselves ARNING but should contract the appropriate electric inspection authority WE or an electrician as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combina tion of devices subject only to the requirement that the total of the Load Numbers of all devices does not exceed 100 vi IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS When using your telephone equipment please follow these basic safety precautions to reduce the risk of fire electrical shock or personal injury 1
7. ennen vennen 2 2 Figure 2 2 Installing Plug on Board esee eee ene 2 4 Figure 3 1 TSU 100 Main Menu nennen n nennen 3 2 Figure 3 2 PORT STATUS Submenus sss ene 3 3 Figure 3 3 LOOP STATUS Display esses nen 3 3 Figure 3 4 T1 STATUS Display ccs eene neret 3 4 Figure 3 5 PORT CONFIGURATION Submenus ananas eneen vereen 3 5 Figure 3 6 Network Locations sees eene nennen nnns 3 6 Figure 3 7 PORT UTILITY Submenus sss eee nnn 3 7 Figure 3 8 PORT TEST Submenus sssssssseeeee eee nenne 3 7 Figure A 1 Dual U BRITE Option Cards Menu Tree nennen A 1 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual xi List of Figures xii Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 List of Tables Table 2 1 2 Wire Voice Pinout Connection annees venen serene 2 3 Table 3 1 PORT CONFIGURATION Parameters eee 3 5 Table 3 2 PORT TEST Parameters sese eene nennen tete 3 8 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual xiii List of Tables xiv Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 1 Introduction DUAL U BR1TE PLUG IN AND PLUG ON OPTION CARDS The Dual U BR1TE Plug in and Plug on Option Cards are compatible with the TSU TDU HSU family of T1 multi plexers The Plug in Dual U BRITE is designed to occupy a single slot in a TSU family produc
8. limited to loss of data or informa tion loss of profits or loss of use ADTRAN is not liable for damages for any cause whatsoever whether based in contract tort or otherwise in excess of the amount paid for the item Some states do not allow the limitation or exclusion of liability for incidental or consequential damages so the above limitation or exclu sion may not apply to Customer viii Table of Contents List Of Figures xi Eist of Tables ECC xiii Chapter 1 Introduction senen oso sonor ononenenenenenenenenenenenenenenononenenenenevenenevevenenovene 1 1 Dual U BRITE Plug in and Plug on Option Cards ss 1 1 Functional Descriptions 2 nre repr err eet titi drehen 1 1 Features bal Ianus Pad Se Ta itd 1 2 Dual U BRITE Option Card see eee 1 2 Physical Description ore tene eee deer eere 1 3 Chapter 2 Installation enesesesesonosesenenenenenenenenenenenenenenenenenenenenenenenenenenenenene 2 1 Unpack Insp ct Power Up aet eee eee eere 2 1 Rec rpt Inspection nee pen ede e e e ede ees 2 1 ADTRAN Shipments Include 7 i eee eee 2 1 Provided by Customer niet ue eee Ferte a ee tinere etre rated rione 2 2 Dual U BRITE Plug In Option Card Installation eese 2 2 Placement of the Option Module nnn susanne nernene senen eeneneenenenener een 2 2 PowerConnect sss hide v ERI RR do Er REO e Exe eod pee de er Se Yen set den
9. limits Change or modifications to this unit not expressly approved by CAUTION the party responsible for compliance could void the user s author ity to operate the equipment CANADIAN EMISSIONS REQUIREMENTS This digital apparatus does not exceed the Class A limits for radio noise emis sions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Department of Commu nications Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur Appareils Numeriques NMB 003 edictee par le ministre des Com munications CANADIAN EQUIPMENT LIMITATIONS Notice The Canadian Industry and Science Canada label identifies certified equipment This certification means that the equipment meets certain telecom munications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfac tion Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equip ment must also be installed using an acceptable methods of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly telephone extension
10. 1TE Dual U BRITE Plug in Option Card e Dual U BRITE Plug in Option Card e User Manual to be inserted into main TSU 100 120 600 User Manual Dual U BRITE Plug on Option Card e Dual U BRITE Plug on Option Card e User Manual to be inserted into main TSU 100 120 600 User Manual e Four each 4 screws 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 2 1 Chapter 2 Installation Provided by Customer The customer must provide cables for connection to othe equipment DUAL U BR1TE PLUG IN OPTION CARD INSTALLATION Placement of the Option Module Figure 2 1 represents the action required for proper place ment of the option module 1 Remove cover plate from the rear panel 2 Slide option module into the rear panel until it is positioned firmly against the front of the unit 3 Fasten thumb screws at both edges of option mod ule r 4 Cover Plate TSU 100 120 600 ey Cac Option Module Figure 2 1 Installing the Option Module Power Connection Each option module derives power from the base TSU 120 600 unit Power to the base unit is supplied by a cap tive eight foot power cord 2 2 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 2 Installation Wiring The option module offers two connectors for the U inter faces The connectors are universal and accept either an RJ 45 8 pin or an RJ 11 6 pin modular plug The pinout is gi
11. 2 2 WATT LG ih Ret ie esitare vines fa beet shack veld een ri iom i ea gola reir er totg 2 3 Attaching the Plug on Board to the Option Card esses 2 3 Power Up Testing and Initialization eee eee 2 5 Successt lSelf Tesb u oct Et ertet eerte Ore A D E 2 5 Failed Self Test i ttt teet eme eth o e ete eerte dep 2 5 Operation Alarms eet cete edes e E ERI I Rer efe 2 5 Chapter 3 Operation senen one venenonononevenenonenonenenenenenenenenenenevenenenenenenenenevenenenevene 3 1 OVEEVIEW o so itte re tee Ri dti ret edu t aed 3 1 Menu Str ct te etae dente eee tete Pe 3 1 Menu Operation aanrenden elden de e dee 3 1 Dual U BR1TE Menu Items eese onser enverenvensereeneveseenverenvereseeene 3 2 SING ids tcs o ets Kies EE nO TO oh o ets fco tes f da 3 4 CRGA Sa sae EEA EE UI ICE HB REPE RU I re eto tote 3 4 NCT Oe aac HO t tree Ree E Ree ends 3 4 TSU Features used with Dual U BRITE Options 55 eee 3 9 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual ix Table of Contents Appendix A Dual U BR1TE Option Card Menu Tree 1 22 A 1 Appendix B Dual U BR1TE Failure Messages X Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 List of Figures Figure 1 1 Dual U BRITE Plug in Option Card nennen vennen 1 3 Figure 1 2 Dual U BRITE Plug on Option Card sees 1 4 Figure 2 1 Installing the Option Module enen
12. ADRAN Dual U BR1TE Plug In Option Card Part Number 1200107L1 HS and Dual U BR1TE Plug On Option Card Part Number 1200108L1 USER MANUAL 61200107L1 HS 1B June 2000 ADRAN 901 Explorer Boulevard P O Box 140000 Huntsville AL 35814 4000 256 963 8000 2000 ADTRAN Inc All Rights Reserved Printed in U S A NOTE Notes provide additional useful information Cautions signify information that could prevent service interrup CAUTION tion Warnings provide information that could prevent damage to the Y D W ARNING equipment or endangerment to human life FCC regulations require that the following information be provided in this man ual 1 This equipment complies with Part 68 of the FCC rules The required label is affixed to the bottom of the chassis 2 If this equipment causes harm to the telephone network the telephone com pany may temporarily discontinue service If possible advance notification is given otherwise notification is given as soon as possible The telephone company will advise the customer of the right to file a complaint with the FCC 3 The telephone company may make changes in its facilities equipment opera tions or procedures that could affect the proper operation of this equipment advance notification and the opportunity to maintain uninterrupted service is given 4 Ifexperiencing difficulty with this equipment please contact ADTRAN for repair and warranty info
13. E UP TONE Figure 3 5 PORT CONFIGURATION Submenus The unit displays the first of four submenu items Table 3 1 identifies the available selections for PORT CONFIGURA TION Continue with standard operating procedures Table 3 1 PORT CONFIGURATION Parameters MENU ITEM PARAMETER CHOICES SERVICE 2B4D 2B B1 D B2 D B1 B2 ZBS DISABLE ENABLE MODE LULT LUNT WAKE UP TONE OFF ON Factory Default SERVICE SERVICE allows the user to select the ISDN channels to be transmitted over the T1 facility Each channel requires one DSO of the T1 in which to transmit and receive data All switched applications will require the D channel The user must provision the proper number of consecutive DSOs of the T1 facility for proper operation ZBS For proper operation the ZBS zero byte substitution for two U BRITE ports connected by a T1 facility must be the same value The ENABLE parameter for ZBS must be se lected if the T1 is using AMI line coding If the T1 facility is using B8ZS line coding the DISABLE parameter may be chosen 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 3 5 Chapter 3 Operation MODE The U BRITE port should be configured to operate in the LULT mode if being operated in the Adjacent to Customer or Tandem Office Source positions see Figure 3 6 on page 3 6 The MODE should be set to LUNT if the port is oper ated in the Adjacent to Switch or Tandem Offi
14. L LPBK Remote loopbacks of the B1 channel in the network to customer direction are initiated by selecting items under this menu The loopback may be requested for this unit and the five next U BRITES toward the NT1 A LOOP ING message is displayed on the LCD once a test has been initiated The initiating U BR1TE sends the loopback command and begins transmitting the internally generat ed 2047 pattern When the U BRITE begins receiving the 2047 pattern it displays FAR END LOOPED on the LCD The initiating U BR1TE transmits the 2047 pattern for the duration of the test The user can view the pattern results by choosing menu item 7 PATT RESULTS and can inject errors into the transmitted pattern by choosing menu item 6 INJECT ERROR Select NO LOOPBACK under the B1 REMOTE LPBK menu to exit the test The B2 REMOTE LPBK operates exactly like the B1 RE MOTE LPBK TEST but the B2 channel is looped back rath er than the B1 channel The local U BR1TE may be commanded to loop back ei ther the B1 or B2 channel When a channel is put in LOCAL LOOPBACK it will loop back both the T1 and U interface data associated with the channel 3 8 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 3 Operation B1 2047 PATT B2 2047 PATT INJECT ERROR PATT RESULTS A U BRITE port may be commanded to transmit the in ternally generated 2047 pattern on the B1 channel in ei ther the T1 T1 TX or the U interface LP TX
15. T 3 SET PASSCODE 4 5 SOFTWARE REV 6 PORT UTILITY IA UBR1TE sw REVISION 1 NETWORK TESTS Figure 3 7 PORT UTILITY Submenus Display 1 1 UBR1TE scroll to display if necessary and press Enter The unit displays the option card name and the software version installed Press Cancel to exit or se lect another port PORT TEST a submenu of the TSU 100 120 600 main menu item TEST activates tests of the selected data ports Selecting the Dual U BRITE displays tests available for this option card See Figure 3 8 1 B1 REMOTE LPBK 2 RUN SELF TEST 2 B2 REMOTE LPBK 3 PORT TEST IA UBR1TE 3 LOCAL LOOPBACK 4 CANCEL TEST 4 B1 2047 PATT 5 B2 2047 PATT 6 INJECT ERROR 7 PATT RESULTS Figure 3 8 PORT TEST Submenus 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 3 7 Chapter 3 Operation Table 3 2 identifes the available selections for PORT TEST Table 3 2 PORT Test Parameters B1 2047 PATT B2 2047 PATT MENU ITEM PARAMETER CHOICES B1 REMOTE LPBK ADDRESS 1 2 3 4 5 6 NT1 NO LOOPBACK B2 REMOTE LPBK ADDRESS 1 2 3 4 5 6 NT1 NO LOOPBACK LOCAL LOOPBACK B1 B2 NOLOOPBACK T1 TX LP TX NONE T1 TX LP TX NONE INJECT ERROR Inserts error into transmitted pattern PATT RESULTS Activates deactivates the display of the test pat tern s errored seconds B1 REMOTE LPBK B2 REMOTE LPBK LOCA
16. TEST stalled default setting for all Dual U BRITE option mod ule parameters When FACTORY RESTORE is displayed place the cursor on itand press Enter The unit is restored to preset factory de faults and returns to the main menu The factory default for port configuration parameters is shown in Table 3 1 on page 3 5 RUN SELF TEST a submenu of the TSU 100 120 600 main menu item TEST executes both the Dual U BRITE inter nal test and the TSU 100 120 600 internal test The results of the self test are displayed in the LCD See the TSU 100 120 600 User Manual for additional information on SELF TEST When RUN SELF TEST is displayed place the cursor on it and press Enter to execute the test The unit continuously changes the display in the LCD window until all test re sults are shown 3 10 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 AppendxA Dual U BR1TE Option Card Menu Tree The menu tree for the Dual U BR1TE Plug in and Plug on Option Cards is provided in Figure A 1 1 Port Status 1 LOOP STATUS 2 T1 STATUS 3 LOOP MONITOR 1 SERVICE ZBS 3 MODE 4 WAKE UP TONE n 2 Port Config 3 Port Utility sw Revision 1 B1 REMOTE LPBK 2 B2 REMOTE LPBK 4 Port Test 3 LOCAL LOOPBACK 4 B1 2047 PATT 5 B2 2047 PATT 6 INJECT ERROR 7 PATT RESULTS Figure A 1 Dual U BR1TE Option Cards Menu Tree 61200107L1 HS 1 Dual U BR1TE Plug in Option Card
17. artial self test during the power up sequence as described in the TSU 100 120 600 manual A full self test can be activated from the Test menu No initialization input is required Any previously configured setting for the Dual U BR1TE is restored automatically upon power up Successful Self Test Failed Self Test Operation Alarms The green OK LED located on the front panel turns on when a successful self test is completed and the configu ration is successfully restored See the chapter Operation in the main user manual If the Dual U BRITE card fails one or more of the self tests a message is displayed in the LCD during power up See the TSU 100 120 600 user manual Specific failures of the Dual U BR1TE Card are identified in the appendix Dual U BR1TE Failure Messages in this manual The red ALARM LED on the front panel turns on when an alarm condition is detected 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 2 5 Chapter 2 Installation 2 6 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 3 Operation OVERVIEW Menu Structure Menu Operation The Dual U BRITE card is controlled as part of the TSU 100 120 600 using the same methods as described in the TSU 100 120 600 User Manual See the TSU 100 120 600 User Manual for descriptions of front panel indicators and buttons When an option card is installed in the TSU 100 120 600 the unit adds it to the list of selec
18. back capability for full 2B D as well as individ ual B channels in both loop and carrier directions e Bland B2looopback addressability for the NT1 and up to six devices in the downstream toward the NT1 direction e Local performance monitoring without test equip ment Dual U BR1TE Option Card The Dual U BR1TE Option Cards conform to the follow ing specifications U Interface Line 2 wire tip and ring Rate 160 kbps full duplex Frequency 40 kHz Line Code 2B1Q Max Line Loss 42 dB 9 40 kHz Max Distance 18000 ft with 1300 ohm resistance design ISDN Interface RJ 45 Connector 1 2 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 1 Introduction Compatibilit ISDN 2B1Q Inter ANSI T1 601 1992 face Performance TR NWT 000397 and TR TSY 000829 ISDN BR over T1 TR NWT 000397 Approvals FCC Part 15 FCC Part 68 UL Diagnostics and Tests Loopback B1 B2 loopbacks and 2B D loopbacks initiated through EOC as specified by TR NWT 000397 and ANSI T1 601 1992 Selftest RAM test Slot selection test EPROM checksum test Physical Description The Dual U BRITE Plug in Option Card see Figure 1 1 is designed to occupy a single slot in a TSU family prod uct PORT X 3 X 4 DUAL U BR1TE PORT X 1 PORT X2 HOT REPLACABLE Figure 1 1 Dual U BR1TE Plug in Option Card The Dual U BRITE Plug in Option Card rear panel in cludes a plastic plug ove
19. ce Sink po sitions WAKE UP Periodic wake up tones should be turned on when the TONE port is operated in the Tandem Office Sink configuration or when it is adjacent to a device that requires wake up tones Dual U BR1TE Dual U BR1TE Port Port T Carrier AZC TSU TSU Adjacent to Adjacent to Switch Customer Dual U BR1TE Dual U BR1TE Dual U BR1TE Dual U BR1TE pius Port Port Port 2 Wire ISDN D T Carrier T Carrier L Loop Switch N L DOCCCOCOG Customer T T NT1 TSU TSU TSU Adjacent to Tandem Office Tandem Office Sink Adjacent to Customer Switch Source U Repeater Dual U BR1TE EARS Port L rou Customer T NT1 TSU U Repeater Adjacent to Tandem Office Switch Source U Repeater Figure 3 6 Network Locations 3 6 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 3 Operation PORT UTILITY 3 UTIL PoRT UTILITY a submenu of the TSU 100 120 600 main menu item UTILITIES UTIL displays the current software information for each port installed in the unit This infor mation is required when requesting assistance from ADTRAN Technical Support or when updates are need ed When PoRT UTILITY is displayed place the cursor on it and press Enter to display the first available port See Fig ure 3 7 1 TIME DATE 2 FACTORY RESTORE PoRT TEST 4 TES
20. direction The pattern may be looped back to the U BRITE port and verified with the results viewed by choosing 7 PATT RE SULTS or the 2047 pattern may be verified using test equipment at accessible points in the network Errors may be injected into the transmitted pattern by choosing 6 IN JECT ERROR B2 2047 PATT operates exactly like B1 2047 PATT with the pattern transmitted in the B2 channel instead of the B1 channel Selecting this menu item while the U BRITE is transmit ting the 2047 pattern B1 REMOTE LPBK B2 REMOTE LPBK B1 2047 PATT B2 2047 PATT inserts an error in the transmitted pattern Selecting this menu item while the U BR1TE is transmit ting the 2047 pattern causes the U BR1TE to display the maximum number of errored seconds of the test pattern on the bottom line of the LCD ES xs The display con tinues until this menu item is selected a second time Pressing shift clear while in this menu resets the errored seconds to zero TSU FEATURES USED WITH DUAL U BR1TE OPTIONS FACTORY RESTORE In addition to the Dual U BR1TE menu items two addi tional menu items of the TSU 100 120 600 may be oper ated in conjunction with the Dual U BRITE option module These are FACTORY RESTORE and RUN SELF TEST FACTORY RESTORE a submenu of the TSU 100 120 600 main menu item UTIL UTILITIES restores the factory in 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 3 9 Chapter 3 Operation RUN SELF
21. fications and drawings for such products which may or may not be reflected in the Product Manual This warranty only applies if Customer gives ADTRAN written notice of defects during the warranty period Upon such notice ADTRAN will at its option either repair or replace the defective item If ADTRAN is unable in a reasonable time to repair or replace any equipment to a condition as warranted Customer is entitled to a full refund of the purchase price upon return of the equipment to ADTRAN This warranty applies only to the original purchaser and is not transferable without ADTRAN s express written permission This warranty becomes null and void if Customer modifies or alters the equipment in any way other than as specifically authorized by ADTRAN EXCEPT FOR THE LIMITEDWARRANTY DESCRIBED ABOVE THE FOREGO ING CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF THE CUS TOMER AND THE EXCLUSIVE LIABILITY OF ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES INCLUDING WITH OUT LIMITATION ALL WARRANTIES OF MERCHANTABILITY AND FIT NESS FOR A PARTICULAR PURPOSE SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES SO THIS EXCLUSION MAY NOT APPLY TO CUSTOMER In no event will ADTRAN or its suppliers be liable to Customer for any inciden tal special punitive exemplary or consequential damages experienced by either Customer or a third party including but not
22. r a cutout for additional connec tors This allows a plug on board to be added to the Dual U BRITE Card The PORT X Y indication is linked to the port numbering philosophy of the TSU 100 product fam ily The X represents the slot number and the Y indicates the port number For the TSU 100 application there is only one option slot Therefore the ports are designated 1 1 and 1 2 If added the plug on board port designations 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 1 3 Chapter 1 Introduction are 1 3 and 14 These port numbers appear in the front panel liquid crystal display LCD menu displays The Dual U BR1TE Plug on Option Card see Figure 1 2 is designed to plug on any TSU DSU plug in card DUAL U BRITE PORT X 3 X 4 PORT X 1 PORTX2 ah ET T HOPLACEABLE Figure 1 2 Dual U BR1TE Plug on Option Card 1 4 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 2 Installation UNPACK INSPECT POWER UP Receipt Inspection Carefully inspect the option module for any shipping damage If damage is suspected file a claim immediately with the carrier and contact ADTRAN Customer and Product Service If possible keep the original shipping container for use in shipping the option module for repair or for verification of damage during shipment ADTRAN Shipments Include The following items are included in ADTRAN shipments of the Dual U BR
23. rmation The telephone company may require this equipment to be disconnected from the network until the problem is cor rected or it is certain the equipment is not malfunctioning 5 Thisunit contains no user serviceable parts 6 AnFCC compliant telephone cord with a modular plug is provided with this equipment This equipment is designed to be connected to the telephone net work or premises wiring using an FCC compatible modular jack which is Part 68 compliant 7 The following information may be required when applying to the local tele phone company for leased line facilities Service Type REN SOC FIC USOC ISDN 6 0N 02155 RJ 49C FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equip ment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accor dance with the instruction manual may cause harmful interference to radio fre quencies Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the inter ference at his own expense Shielded cables must be used with this unit to ensure compliance with Class A FCC
24. t and will accept plug on modules designed for use in this product family The Dual U BRITE Plug on Module may be plugged on any TSU TDU plug in module The Dual U BR1TE Option Cards are subject to the host T1 multiplexer s operation and control The Dual U BRITEs provide two ISDN U interfaces and allow the transport of Basic Rate ISDN BRI information over T1 carriers and unloaded twisted pair wiring Functional Description The Dual U BR1TEs are configured in the same manner as the host multiplexer The internal menu for the configu ration of each U BRITE is a part of the Dual U BR1TE Module and is automatically available when the Dual U BRITE is installed into the TSU The Dual U BR1TEs provide two U interfaces Each U in terface allows the transmission and reception of Basic Rate 2B D information over three consecutive DSOs of the TSU family s T1 facility and is capable of operating in ei ther the LUNT or LULT mode 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 1 1 Chapter 1 Introduction Features Both Dual U BR1TE Option Cards have the following features Internal test pattern which allows for testing of indi vidual B channels without requiring external test equipment e Transportation of ISDN Basic Rate 2B D information over T1 facilities in the 3 DS0 format e Performance monitoring of the layer 1 facility e Firmware configurable to line unit LT or line unit NT mode of operation e Loop
25. table options under the Port menu items These menu items are shaded in the limited overview of the TSU 100 menu shown in Figure 3 1 on page 3 2 The appendix of the TSU 100 User Manual shows a complete menu diagram Anoption module must be selected from the listing in one of the Port menu options before any option module menus are applicable With the cursor on one of the Port menu items press Enter to display a list of the currently installed option modules To activate menus for the Dual U BRITE card scroll through the list to display X Y U BR1TE and press Enter The X represents the slot number and the Y identifies the port number 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 3 1 Chapter 3 Operation TSU 100 MAIN MENU Once the option module is selected the Dual U BR1TE menus appear as a subset of and operate the same as menus for the TSU 100 120 600 Use the up and down ar rows to place the cursor on the desired item and press En ter to display the first two submenu choices 1 NI PERF REPORTS 1 STATUS 2 NI ERRORS 1 NETWORK NI 3 ACTIVE ALARMS 2 UNIT 4 VIEW HISTORY BEEN 3 MAP XCHNG 5 PORT STATUS 4 MAP IN USE A B 6 REMOTE PORT 5 DS0 MAP A 6 CLEAR PORT ALM 6 DSO MAP B 7 PORT CONFIG TIME DATE FACTORY RESTORE 1 NETWORK TESTS 2 RUN SELF TEST 3 PORT TESTS 4 CANCEL TEST UNIT ID SOFTWARE REV 6 PORT UTIL 1 2
26. ven in Table 2 1 The required wiring connections are Connector Type USOC RJ 45 Part number AMP 555164 1 Table 2 1 2 Wire Voice Pinout Connection Pin Name Description 5 TIP Tip lead of 2 wire interface 4 RING Ring lead of 2 wire interface 1 2 3 6 7 8 UNUSED Pins used to mate with the Dual U BRITE connector are as follows RJ 11 RJ 45 Tip Ring Tip Ring pin 4 pin 3 pin 5 pin4 Attaching the Plug on Board to the Option Card Figure 2 2 represents the action required for proper place ment of a plug on board on the option card 1 Hold the plug on board above the option card 61200107L1 HS 1 Dual U BR1TE Plug in Option Card User Manual 2 3 Chapter 2 Installation 2 Using a downward and right to left motion slip the DB 15 connector into the opening in the option card back panel 3 Moving the plug on board downward secure the connection of the header pins at the front of the board 4 Install the four 4 40 screws at the top and bottom of the plug on board Figure 2 2 Installing Plug on Board The connection of the header pins between the option card and the plug on UT board must be visually verified Severe damage of the device can result from an improper connection 2 4 Dual U BR1TE Plug in Option Card User Manual 61200107L1 HS 1 Chapter 2 Installation POWER UP TESTING AND INITIALIZATION The Dual U BR1TE Option Card executes a p
Download Pdf Manuals
Related Search