DSPKR User Manual
Contents
1. adequate access can be gained to allow operation of the Function button Furthermore when installing in vehicles ensure that the unit is not in direct sunlight or in a hot area Make sure that the 3 5mm plug lead and fused DC power lead are routed away from sources of electronic interference or RF cables For best results try to use a separate power supply to power the speaker and in a vehicle power directly from the vehicle battery as this will minimise the chance of alternator whine and other electronic interference occurring Page 3 4 Operation Once installed and connected to the required audio source apply power to both the audio source and the speaker When power is applied to the speaker the indicators will step through in sequence and the speaker will emit a low tone and the two high tones 5 Audio Level setting An AUDIO LEVEL LED indicates the audio input level that is being received from your audio source Once the correct audio level has been set on your audio source the volume control on the DSPKR is used to adjust the volume to suit your conditions To set the audio level turn your source volume control down to zero the DSPKR volume can also be set low or zero Slowly increase the source volume until the AUDIO LEVEL LED lights The optimum input level is when the LED is on continuously most of the time but if this is not achievable the unit should still function correctly as long as there are some flashes of green2. AUDIO LEVEL LED If the AUDIO LEVEL LED flashes rapidly it indicates that audio input level is too high and audio distortion may occur Reduce the source volume until the rapid flashing virtually stops ON FUNCTION Button STATUS LED AUDIO level LED 6 ON Noise Cancellation voo Never mA The DSPKR STATUS LED will show Red to indicate that noise cancelling is off When the FUNCTION button is pressed momentarily the unit will step through the noise cancelling levels and the STATUS LED will be Orange Each time the FUNCTION button is pressed the speaker will beep a number of times corresponding with the filter level and the STATUS LED will also flash starting with one beep and flash for filter level one ending with 7 beeps and 7 led flashes for level 7 A double tone will be heard when the button is next pressed and the LED will turn red again Subsequent button presses will cause the speaker to cycle back through the 7 filter levels again Use this feature to select and store your desired filter level 6 1 to suit your listening conditions If the speaker volume is too high it may be difficult to hear the beeps If the speaker is switched off at this stage it will go back to DSP filter off and the STATUS LED will be red i pu Noise cancellation Filter level table Noise STATE Tone White Noise Cancelling Indicator Reduction Reduction dB dB OFF Red None None 1 Orange 4 9 2 Orange 5 11 3 O
3. and by bhi Ltd No user serviceable parts inside Weee Statement for correct disposal of this product X Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates mmm that it should not be disposed of with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for dis bhi Ltd PO Box 318 Burgess Hill West Sussex RH15 9NR England Telephone 44 0 1444 870333 Email sales bhi ltd com Web www bhi ltd com 1072 105D iss E Page 8
4. ewcieeeect ane eia e a aa page 4 6 1 Storing and un storing of filter level cceeeeeeeee seen eee eeeeee page 5 T Sleep MMO ic teicsnsiscieina iise aanrand aa E e E E aa page 5 7 1 Auto sleep function sapeseccssinescecedcnccesixecietnetantwexncesoxensweeeetententves page 5 T 2 Waking Up the UNL sdiscescciccccescnescesctecscssszadescacnmscescescasessacncesesd page 6 8 SPECWICAUON sosccssciantenxanivotancsvadcesau deneu aN ea page 5 9 Troubleshooting FAQ S asssnsnunnunnunnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn page 6 OETA SUD OW aee a e e A E a page 7 Page 2 DSPKR 10 Watt RMS Amplified DSP noise cancelling Speaker 1 Packing List The DSPKR is shipped with the following DSPKR noise cancelling speaker Integral black audio lead with 3 5mm mono plug attached Speaker mounting bracket Fused DC power lead 1030 FPL Red cable ve Black red cable ve Mounting screws Operating manual amp customer feedback card 2 Introduction The bhi DSPKR amplified DSP noise cancelling speaker greatly improves the clarity and intelligibility of speech in radio and voice communication systems It is suitable for use in many applications where high background noise and interference mean that you cannot clearly hear what is being said The speaker will enable the user to listen and concentrate stress free Suitable applications where the speakers will be of great benefit are Amateur radio CB radio two way radio HF rad
5. io marine communications scanners taxi base stations and especially mobile installations The speaker incorporates unique DSP technology to remove unwanted background noise and interference from speech and has up to 7 DSP filter levels allowing the user to optimise for their level of noise and interference The speaker simply connects into the extension speaker socket or headphone socket of your audio equipment The DSPKR comprises a wide frequency range 4 speaker and an audio amplifier capable of producing up to 10 Watts RMS audio power with built in bhi DSP noise cancelling technology The unit also has a sleep mode and requires an audio input signal of between 80 and 500mV level and a DC supply of between 10 and 16 Volts 2A The unit is supplied with an attached black 2 metre audio cable with a moulded 3 5mm jack plug for the audio input and a 1030 FPL 2 1mm fused DC power lead with bare ends A 3 5mm mono auxiliary output socket is provided to allow the speaker to be used with headphones or to drive another loudspeaker A 12V DC power supply PSU12 1A is available as an optional extra for UK customers and the PSU12 1A EU for European customers Note The DSPKR is designed for speech signals and is not really suitable for music 3 Installation The speaker comes with a mounting bracket that enables the speaker to be used free standing on a desk or secured into vehicles using the self tapping screws provided When installing ensure that
6. ker headset socket Integral 2M long 3 5mm mono jack plug lead audio input 9 Troubleshooting FAQs Speaker doesn t work at all no sound from the speaker e Check that the power connector on your power supply is suitable for the power socket on the speaker 2 1mm centre positive Check the fuse Check connections to your power supply e Check that you have switched your radio communication equipment on and that you have a signal for the speaker to process To verify this remove the audio connector from the external speaker socket on your equipment e Check that the AUDIO LEVEL LED is illuminating green The green input overload LED doesn t illuminate or only seems to come on when the speaker is very loud or doesn t appear to operate properly e The factory default input overload LED setting is calibrated so that the audio input level to the speaker is correct This factory setting can be restored by the following procedure 1 Ensure NOTHING is connected to the audio input of the DSPKR 2 Hold FUNCTION button down 3 While still holding the button down apply power to the DSPKR Don t let go of the button 4 Keep the button held down for the full 30 seconds until you hear chimes an beeps 5 Release the button Page 6 The speaker works but the noise cancellation doesn t appear to improve the audio quality of the signal e Check the filter is switched on and increase the level to see if this makes any difference e Check
7. l DSPKR 10 Watt Amplified DSP noise cancelling Speaker User Manual Issue E phi BSP Noise cancellation bhi Ltd DSP noise cancellation products for radio and voice communications 1072 105D Iss E Important Information Copyright This publication including all photographs and illustrations is protected under international copyright laws with all rights reserved Neither this manual nor any of the material within may be copied or reproduced without the written consent of bhi Ltd Disclaimer The information in this document is subject to change without notice bhi Ltd makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose Furthermore bhi Ltd reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of bhi Ltd to notify any person of such revision or changes Table of Contents f Packing LiStissi set seo de oatcee toda neds secenntatdduved ueearectcdenitdedeieuetetidencadins page 3 2 INVER OCU CUI siccetense cectesicnns wnwensecn ea mce tessa manent won eee EEEE ENa aE EE haaa page 3 3 Installation aa a aa aN a page 3 4 MOA ST AN ys ides less Gears hele pc Ea E EE page 4 5 Audio level SCHING s cscsscdictsacesssncececccass tan dcccancenesecse van esstadacessytaecsen page 4 6 Noise cancellation a sce scien crises
8. nd the noise cancellation is then switched off the resulting unprocessed signal will be at a higher level Care must be taken to avoid excessive signal levels to avoid possible damage to your hearing or equipment bhi Ltd does not accept responsibility for damage to equipment or hearing however caused 7 Sleep mode The DSPKR has a sleep mode to save energy when not in use In this mode the speaker is put to sleep by 1 Pressing and holding the FUNCTION button for approximately 6 seconds You will hear a single beep after a few seconds then after approximately six seconds three beeps descending in frequency Releasing the button after this will leave the speaker in sleep mode or 2 Auto sleep is enabled comes as standard see 7 1 In sleep mode the unit consumes very little current mA and the STATUS indicator flashes red approximately every 15 seconds to show that it is still powered but in sleep mode 7 1 Auto sleep function The Auto sleep feature means that if the unit fails to see any audio above the minimum required level for more than 60 minutes it will automatically go into Sleep mode The Auto Sleep feature can be can be turned on or off at power up by pressing and holding the FUNCTION button whilst turning the power on After approximately 10 seconds a set of two three tone beeps ascending in frequency indicate that the Auto Sleep feature is disabled and a set of two three tone beeps descending in frequency will indicate that A
9. onic interference or RF cables 2 Try using a separate DC power supply for the DSPKR 3 Reduce the volume on your radio in steps and then increase the volume on the DSPKR to compensate as long as the input LED still flashes green the input level is ok until the RF disappears 4 Fit ferrites to the leads at outlined on the bhi website FAQ page http www bhi ltd com index php support faq html 10 bhi support Every DSPKR noise eliminating speaker comes with a 12 month guarantee against defective materials and workmanship If you do have a problem then please refer to the troubleshooting guide section 9 If you have not resolved your problem then please contact us Before you make your call please have the following information to hand 1 Your serial number found on the back of the unit 2 Details of when and where you purchased the unit See our website for FAQs for answers to other common questions otherwise most queries can be resolved over the telephone or via email If not we will arrange with you to have your unit sent back to us for analysis repair or replacement if within 12 months from date of purchase if outside the guarantee period an estimate of the cost of repair will be given Page 7 For contact details please refer to the back cover of this manual If you have any suggestions for improvements please complete and return the customer feedback form Note Opening the case will void any warranty unless agreed beforeh
10. range 6 13 4 Orange 8 15 5 Orange 16 17 6 Orange 21 20 T Orange 25 24 Page 4 6 1 Storing and un storing a selected level of noise cancelling Once a suitable filter level has been selected press and hold the FUNCTION button for a few seconds to store the selection The unit will respond with a single tone beep and the STATUS LED will turn green Further presses of the FUNCTION button will now cause the unit to cycle between noise cancelling off STATUS LED red and noise cancelling on at the saved level STATUS LED green To un store the saved level press and hold the FUNCTION button again until the unit emits a tone The STATUS indicator will change back to red and the unit can now cycle through the various levels of noise cancellation again If the speaker is switched off at this stage it will remember the last stored setting but with noise cancellation off red LED when switched back on Note It is advisable not to drive a vehicle and change the filter level at the same time and higher levels of noise cancellation will remove a lot of noise but the user will note that the audio can be slightly distorted if high levels of noise are present with the signal Switching off the noise cancellation will restore the audio If there is a lot of noise present you may need to increase the output volume when listening with the noise cancellation switched on once the noise has been removed If the volume is increased a
11. that the AUDIO LEVEL LED is illuminating green The volume from the speaker is low and cannot be increased e The speaker is designed to work with external speaker sockets of radio communications equipment and although it will work with some earphone and headphone sockets there may be occasions where the signal output from these is not enough for the speaker electronics to process the signal effectively bhi have another product that will work with these levels of signal the NEIM1031MkKII DSP Noise Eliminating In line Module Please contact bhi for more information Sometimes there is a short delay before the noise cancellation is active e This is due to the time the DSP takes to start processing the signals This gives you the opportunity to check that the DSP is not taking out any detail from the signal Sometimes I can hear a processing sound in the speaker when no signal is present e This is normal and is caused by the DSP processor When a signal is applied you should not be able to hear this in the speaker can hear noises speech in the speaker when transmit e The DPSKR has been specifically designed to minimise against the effects of stray RF If you do hear noises in the speaker this is probably due to high levels of RF being present in the vicinity Carry out the standard checks necessary to minimise this 1 Make sure that the 3 5mm black audio lead and the red black fused DC power lead are routed away from sources of electr
12. uto Sleep feature is enabled After releasing the button you will hear a single beep then a set of three beeps and the STATUS LED will be red indicating the unit is ready for use The unit wakes up if the signal level increases above the minimum required level or if the FUNCTION button is pressed once Three beeps ascending in frequency will be heard and the audio will be restored to the last known setting When the Auto sleep is disabled the speaker is always on and will not go to sleep if no signal is present The speaker can still put to sleep manually as in 7 Above Page 5 7 2 Waking the speaker up The DSPKR will wake up if the signal level increases above the minimum required level or if the FUNCTION button is pressed once Three beeps ascending in frequency will be heard and the audio will be restored to the last known setting 8 Specifications DC Power DC input voltage 10 to 16 Volts DC Current 2 Amps maximum Protection Over current and reverse polarity protected Audio Input Impedance Terminated with approximately 8 Ohm load Minimum input level 80 to 500 mV for correct working levels Maximum 6 Watts maximum withstand Audio output Impedance Internal Speaker 8 Ohms Nominal External speaker phones 4 Ohms minimum Level 10 Watts nominal with 12V DC supply Controls On function button Speaker volume control Indications Power ON FUNCTION AUDIO LEVEL Connections 2 1mm DC power jack 3 5 mm mono external spea
Download Pdf Manuals
Related Search