POLAR EQUINE CS600X TROTTING
Contents
1. 0167 10 ENGLISH 6 PLACING THE CS600X ON THE SULKY The support has been designed so that the CS600X training computer is always facing you not perpendicular wherever you install it on the sulky 1 Place the rubber part on the sulky bar or stem and insert the support on top of it 2 Pass the cable ties over the support and adjust them around the sulky bar stem 3 Secure the bike mount firmly and cut off any excess cable tie ends 4 Position the CS600X training computer on to the support Turn the CS600X training computer clockwise until you hear a click It is now ready for use You can release the CS600X training computer by pressing it down and simultaneously turning it counter clockwise Alternatively you can use the wrist band to carry the training computer on your wrist ENGLISH 11 7 PLACING THE BELT 1 For the heart rate sensor to read the heart rate properly ensure a good contact between the plastic electrode areas and the horse s skin Wet the belt properly for example in a bucket of water 1 2 Also wet the horse s hair from the areas where the electrodes of the belt are placed 2 If your horse has long or thick hair you can clip those areas This greatly improves the heart rate signal quality 3 Attach the heart rate sensor to the pocket 3 Close the pocket firmly 12 ENGLISH 4 Place the belt as indicated 4 with the heart rate sensor pocket on the left side of the horse2. only operate using an antenna of atype and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more han that necessary for successful communication This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Avis de conformit la r glementation d Industrie Canada Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passe pas l intensit n cessaire l tablissement d une communication satisfaisante Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouil
3. this value in the CS600X training computer Wheel size settings are a prerequisite for correct speed information 8 ENGLISH Basic Settings You must enter the basic settings even though they don t concern the horse If you don t enter the basic settings the CS600X training computer will remind you to set them before every exercise Use the UP and DOWN buttons to customize the following basic settings Press OK to confirm your settings Time display 241 121 Time Date day month year or month day year e Units kg cm km or Ib ft mi Select Yes Settings are accepted and saved The CS600X training computer displays the time Select No if settings are incorrect and need to be changed Press STOP to return to the data you want to change Once the settings are done the CS600X training computer returns automatically to the time display ENGLISH 5 PLACING THE SPEED SENSOR Attach the rubber part to the sensor 2 Pass the cable ties through the speed sensor and rubber part holes Adjust the sensor to the sulky bar so that the POLAR logo faces outwards 3 Adjust the ties loosely Do not tighten them yet 4 Attach the magnet to a spoke at the same level as the sensor Fasten the magnet to the spoke and tighten it with a screwdriver 5 Fine tune the positioning of both the magnet and the speed sensor so that the magnet passes close to the sensor but does not touch it max 4 mm
4. 600X training computer Press UP or DOWN to change the view The name of the display appears for a few seconds The name indicates the information on the lowest row 9 STARTING TRAINING RECORDING You can customize the CS600X display to view the information you need the most during training either by using the training computer or the ProTrainer 5 software The information available depends on the features that are activated For instructions see the full user manual at www polar com support You can also zoom the display Press and hold UP to zoom into the upper row and DOWN to zoom into the middle row Return to the normal display by pressing and holding the buttons again ENGLISH 15 16 To stop the exercise press STOP twice The CS600X returns to the time display To view detailed information on the exercise session select File The Exercise Log lists maximum of 99 exercise files The Weekly summary displays summaries for the past 16 weeks Totals include cumulative values recorded during training sessions e Inthe Delete menu you can delete exercise files For a deeper analysis transfer the data to Polar ProTrainer 5 The software offers you different options to analyze the data For instructions download the full user manual from the CD or at www polar com support ENGLISH You can also transfer the data to polarpersonaltrainer com web service by using the WebLink sofware Dow
5. POLAR EQUINE CS600X TROTTING Getting Started Guide POLAR LISTENS TO YOUR BODY CONTENTS 1 INTRODUCTION 3 7 PLACING THE BELT 12 2 CONTENTS OF THE SET 4 8 PAIRING SENSORS WITH THE TRAINING COMPUTER 14 3 BUTTON FUNCTIONS 6 9 STARTING TRAINING 4 STARTING THE CS600X 7 RECORDING 15 Sulky Settings 7 Measuring Wheel Size 8 10 IMPORTANT INFORMATION 17 Basic Settings 9 Care and Maintenance 17 Serviced dn a maitre nue 17 5 PLACING THE SPEED Guarantee rn 18 SENSOR 222222222222 10 Disclaimer drar ii mia 21 6 PLACING THE CS600X ON THE 1 INTRODUCTION The Polar Equine CS600X Trotting is the most complete trotting training system for horses available It is developed from the CS600X training system for people Read the user manual carefully to use all system features fully Download the full user manual and this getting started guide in other languages from the CD available in English German French Italian Spanish Finnish and Swedish The latest version of the full user manual and this getting started guide can be downloaded at www polar com support For video tutorials go to http www polar com en polar_community videos ENGLISH 3 2 CONTENTS OF THE SET 1 5600 training computer receives displays and records all the data measur
6. Polar products should thus be disposed of separately in EU countries 4 4 This marking shows that the product is rotected against electric shocks Copyright 2012 Polar Electro Oy FI 90440 KEMPELE Polar Electro Oy is a ISO 9001 2008 certified company All rights reserved No part of this manual may be used or reproduced in any form or by any means without a prior written permission of Polar Electro Oy The names and logos marked with a symbol in this user manual or in the package of this product are registered rademarks of Polar Electro Oy Disclaimer Please note that these guarantee terms shall be applied to Polar Equine products instead of any other Polar Electro guarantee term even if other erms may appear in some product documentation ENGLISH 21 Manufactured by Polar Electro Oy Professorintie 5 FIN 90440 KEMPELE Tel 358 8 5202 100 Fax 358 8 5202 300 www polar com POLAR LISTENS TO YOUR BODY
7. This ensures that the electrode areas of the belt are in the right position The range of the heart rate sensor is over 10 m Therefore you can monitor your horse s heart rate also when lunging For the video go to http www polar com en polar_community videos For instructions on displaying the horses s heart rate and recording a training session see the training computer s user manual The user manual can be downloaded at www polar com support ENGLISH 13 8 PAIRING SENSORS WITH THE TRAINING COMPUTER If you purchase a new heart rate sensor or Equine speed kit sensor it must be paired to your training computer For instructions on pairing the heart rate sensor see Using a New Heart rate Sensor For instructions on pairing the speed sensor W I N D see Using a New Accessory in the full user manual of the training computer Please note that pairing may be referred to as teaching in the user manual If you purchased the sensor and training computer together as a set the sensor is already paired to the training computer In this case you will only need to activate the sensor in your training computer For more information see Feature Settings in the user manual 14 ENGLISH Start the heart rate measurement by pressing OK Within five to ten seconds the horse s heart rate appears on the display Press OK to start recording the exercise You can view three lines of exercise information simultaneously in the CS
8. e battery normal wear and tear damage due to misuse abuse accidents or non compliance with the recautions improper maintenance cracked broken or scratched cases displays modified or altered products or their parts and electrode belt and strap of sensors The guarantee does not cover any damage s losses costs or expenses direct indirect or incidental consequential or special arising out of or related to the product e Items purchased second hand are not covered by warranty unless otherwise stipulated by law During the guarantee period the product will be either repaired or replaced at any of the authorized Polar Service Centers regardless of he country of purchase Guarantee with respect to any product will be limited to countries where the product has been initially marketed Regulatory information is available at www polar com support Compliance Statement Canada Polar Electro Oy has not approved any changes or modifications to this device by the user Any changes or modifications could void the user s authority to operate the equipment Polar Electro Oy n a approu aucune modification apport e l appareil par utilisateur quelle qu en soit la nature Tout changement ou toute modification peuvent annuler le droit d utilisation de l appareil par utilisateur Industry Canada IC regulatory information Under Industry Canada regulations this radio ransmitter may
9. ed by the H3 heart rate sensor and the speed sensor 2 Belt The plastic electrode areas A B on the reverse side of the belt detect heart rate The pocket C protects the heart rate sensor from shocks and scratches and prevents it from falling off the belt 3 heart rate sensor The heart rate sensor sends the heart rate signal to the training computer 4 ENGLISH Speed sensor measures speed and distance in real time ProTrainer 5 Equine edition software displays a training log graphs tables and reports on your PC to further analyse the data recorded during training IrDA USB adapter uses infrared connection to transfer the recorded data from the training computer to the PC Strap If needed use the strap to keep the belt in front of the harness Wrist band By using the wrist band you can carry the training computer on your wrist instead of attaching it on the sulky ENGLISH 5 3 BUTTON FUNCTIONS The CS600X training computer has five navigation buttons and an infrared window to communicate with the PC via the IRDA adapter e UP DOWN Scroll through menus INFRARED and adjust values e OK Enter a menu confirm a selection and start an exercise e STOP Exit a menu return to the previous display leave settings unchanged cancel selections pause and stop the exercise e LIGHT Press once and the backlight is activated for 5 seconds when you press any other button You can al
10. lage et ENGLISH 19 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement Class B digital device notice This Class B digital apparatus complies with Canadian ICES 003 RSS Gen and RSS 210 Cet appareil num rique de la classe B est conforme la norme NMB 003 CNR Gen et CNR 210 du Canada USA Polar Electro Oy has not approved any changes or modifications to this device by the user Any changes or modifi cations could void the user s authority to operate the equipment FCC regulatory information This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation 20 ENGLISH Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particula
11. nload the software from Downloads at www polar com support For more detailed information on using the CS600X training computer download the full user manual from the CD or at www polar com support 10 IMPORTANT INFORMATION Care and Maintenance Follow the caring instructions to ensure reliable measurement and to maximize the life span of the belt and the heart rate sensor The following instructions will help you fulfill the guarantee obligations Heart rate sensor Detach the heart rate sensor from the belt after every use and dry it with a soft towel Clean the heart rate sensor with a mild soap and water solution when needed Never use alcohol or any abrasive material e g steel wool or cleaning chemicals Belt Rinse the belt under running water after every use and hang to dry Clean the belt gently with a mild soap and water solution when needed Do not use moisturizing soaps because they can leave residue on the belt Do not soak iron dry clean or bleach the belt Do not stretch the belt or bend the electrode areas sharply Dry and store the belt and the heart rate sensor separately to maximize the heart rate sensor battery lifetime Keep the heart rate sensor in a cool and dry place To prevent snap oxidation do not store the heart rate sensor wet in non breathing material such as a sports bag Do not expose the heart rate sensor to direct sunlight for extended periods Service During the 12 month guara
12. ntee warranty period we recommend that you have service other than battery replacement done by an authorized Polar Service Center only The warranty does not cover damage or consequential damage caused by service not authorized by Polar Electro For contact information and all Polar Service Center addresses visit www polar com support and country specific websites ENGLISH 17 Guarantee Limited International Polar Guarantee for Equine Products 18 Polar Equine products are developed and manufactured for the usage in equine sports Each product endures rigorous testing before it leaves the factory This guarantee does not affect the customer s statutory rights under applicable national or state laws in force or the customer s rights against the dealer arising from their sales purchase contract This limited Polar international guarantee is issued by Polar Electro Inc for customers who ave purchased this product in the USA or Canada This limited Polar international guarantee is issued by Polar Electro Oy for customers who have purchased this product in other countries Polar Electro Oy Polar Electro Inc guarantees he original customer purchaser of this device hat the product will be free from defects in material or workmanship for twelve 12 months from the date of purchase The receipt of the original purchase is your proof of purchase ENGLISH e The guarantee does not cover th
13. r installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help This product emits radio frequency energy but the radiated output power of this device is far below the FCC radio frequency exposure limits is equipment complies with FCC RF radiation xposure limits forth for an uncontrolled nvironment Nevertheless the device should e used in such a manner that the potential for uman contact with the antenna during normal peration is minimized is crossed out wheeled bin marking shows hat Polar products are electronic devices and are in the scope of Directive 2002 96 EC of the European Parliament and of the Council on waste electrical and electronic equipment WEEE and batteries and accumulators used in products are in the scope of Directive 2006 66 EC of the European Parliament and of he Council of 6 September 2006 on batteries and accumulators and waste batteries and accumulators These products and batteries accumulators inside
14. so lock the buttons by pressing and holding the LIGHT button for two seconds 6 ENGLISH 4 STARTING THE CS600X 1 By default the CS600X training computer is switched off to save the battery Press OK twice to activate it 2 Press UP or DOWN to select language Press OK to confirm Sulky Settings Enter the sulky settings to ensure the speed measurements are accurate If you do not enter the settings the CS600X training computer will remind you to set them before every exercise Use the UP and DOWN buttons to customize the following sulky settings Press OK to confirm your settings Number of sulkies 1 2 or 3 e Wheel size for Sulky 1 in mm Wheel size for Sulky 2 in mm if you use a second sulky Wheel size for Sulky 3 in mm if you use a third sulky If you want to re enter settings press STOP to return to the previous setting ENGLISH 7 Measuring Wheel Size Use the following method to measure the wheel size accurately use the valve to mark the point where the wheel touches the ground Draw a line on the ground to mark that point Valve Valve A B Move your sulky forward on a flat surface for one complete rotation The tire should be perpendicular to the ground Draw another line on the ground at the valve to mark a full rotation Measure the distance between the two lines Subtract 4 mm to account for your weight on the sulky to get your wheel circumference Enter
Download Pdf Manuals
Related Search