JEM ZR12 Smoke Machine
Contents
1. How To Contact Us Note Martin Manufacturing UK reserves the right to modify or change the specification of this product without prior notice No part of this publication shall be copied without permission Martin Manufacturing UK 1999 PAGE 12 MARTIN MANUFACTURING UK PLC PAGE I ZRI2 AL USER GUIDE Introduction The ZR12 is the first small JEM machine to feature the new AL Analogue Link technology This allows units to be linked together and controlled from one JEM Multi Function Controller The ZR12 is also fitted with a 1 KW heat exchanger which guarantees the maximum output from this size of vaporizing System The ZR12 uses the DTP overheat protection device for the best possible overheat protection This was first used on the JEM TECHNO FOG with great success A 2 5 Litre fluid container is supplied to minimize the need for refilling A multi function controller enables the user to operate the machine manually using the FOG button or set the timer for auuotmatic operation The timer has a new feature called x8 mode this allows the timer values to be adjusted from x1 to x8 giving the user more variation in the timer settings There is also a ducting kit for applications where the effect is needed in an area away from the ZR12 Features Analogue Link facility High Power Piston Pump Multifunction Remote Controller DTP Safety System Pump Ramping For Continuous Output 2 5 Litre Fluid Capacity SMD El2. is a high power smoke T machine us c v RS is 5 2d e 9 Always use approved accessories with this machine amp s S03 lt A 6 lt I amp 2 gt d be E 9 Do not spill fluid over the machine if fluid is spilt clean with clean water and o S G QI ee GO S gt E contact an approved JEM dealer for advice E S S S Mains Lead Wiring Instructions 2 Eb lt o s P238 a 182 BS sel s v S SAIS RS S 8 Em Brown Live Ss S S SE SR u Blue Neutral 2 98 QE R3 Green Yelllow Earth ess Ts dc ss zs e 28 es 23 9 8 S 2 S 2 m Note This Appliance must be earthed iz v S vo S 95 2R v aS o 8 Z es 6 s Sa PAGE 10 MARTIN MANUFACTURING UK PLC MARTIN MANUFACTURING UK PLC FAGE 3 ZRI2 AL USER GUIDE Machine Layout ent Bottle E ON Jem Output nozzle Ready LED Heat LED o Multi function controller Analogue link socket Fluid compartment A J _ x H em Mains switch Mains lead PAGE 4 MARTIN MANUFACTURING UK PLC ZRI2 AL USER GUIDE ZRI2 AL Ducting Kit Jubilee cli Ducting adaptor Ducting pipe The JEM ZR12 AL ducting kit enables the user to duct the smoke from the machine to an area where the effect is required This
3. is done by using the JEM ducting adaptor and a length of 100 mm 4 ducting pipe The length can be anything from a couple of metres up to 20 metres or further There are one or two things to beware of when using smoke machines with ducting Firstly if there are bends to redirect the smoke they could cause condensation to form Also an air space must be provided between the output of the machine and the ducting adaptor NOTE Always use the recommended ducting adaptor and ducting pipe others may cause damage to the machine MARTIN MANUFACTURING UK PLC PAGE 9 ZRI2 AL USER GUIDE Using The Analogue Link The ZR12 AL has the ability to connect machines together using a Din lead and then operating all of the machines with one controller This is ideal when there is a need for lots of smoke and there is no DMX to operate the machines Simply remove the controllers from all but one of the machines and then connect a Din lead 5 pin from the slave socket of the first machine the one with the controller to the next machine s remote socket and then from that machine s slave to the next machine s remote socket This can be done from two up to ten machines maximum All of the machines will operate with the same output and timer settings as the first machine Wiring of Din Pin 1 NA Pin 2 Gnd Pin 3 NA Pin 4 NA Pin 5 0 10v Slave Socket Remote Socket Link Cable From Master to Slave Jem Hl
4. time becomes 1 minute 20 seconds TIMER ENGAGE This will engage the timer to fire the machine according to the present settings OUTPUT CONTROL Turning this knob clockwise will increase the output of the machine if turned fully anti clockwise there will be no output DELAY TIME CONTROL This will adjust the amount of time the machine waits between operating when the timer is engaged RUN TIME CONTROL This will adjust the time the machine will operate for when the timer is engaged POWER LED This LED will light when the machine is switched on CYCLE LED This LED will light when the timer is engaged and the machine is operating Timer Values Run Time X1 mode Run Time X8 mode Minimum 2 seconds Minimum 16 seconds Maximum 18 seconds Maximum 2 minutes 24 seconds Delay Time X1 mode Delay Time X8 mode Minimum 2 seconds Minimum 16 seconds Maximum 18 seconds Maximum 2 minutes 24 seconds An extension lead is available from JEM for using the controller out of the machine MARTIN MANUFACTURING UK PLC PAGE 7
5. Jem H i J li J Master Machine Slave Machine PAGE 8 MARTIN MANUFACTURING UK PLC ZRI2 AL USER GUIDE Getting Started 9 Once you have selected the best position for the ZR12 AL you can begin to use the machine First check the power supply you have is correct for the machine if it is you can connect to the power supply and switch the mains switch on at the rear of the machine This will light when switched on now de press the grey stand by button the machine will now heat up which takes around 7 8 minutes While it heats up you should check the level in the fluid container the container can hold up to 2 5 litres of fluid NOTE Do not allow the ZR12 AL to run out of fluid Serious damage may occur if the machine is operated when no fluid is connected 9 When the machine has reached working temperature the green ready LED will light on the top of the machine and the machine can now be operated Check the output knob is turned fully clockwise maximum and press and hold the red fog button The fluid pump will start operating and if the machine has a new container of fluid the fluid will take a few seconds to reach the pump When the pump has primed smoke will be visible The output can now be set to the desired level by turning the output knob The timer may be activated or you can simply use the FOG button when smoke is required 9 Once you
6. ectronics Low Noise Soft Start Pumping Heavy Duty Construction PAGE 2 MARTIN MANUFACTURING UK PLC ZRI2 AL USER GUIDE Notes MARTIN MANUFACTURING UK PLC PAGE 11 ZRI2 AL USER GUIDE ZRI2 AL USER GUIDE Trouble Shooting Safety 8 x D 9 Always use a JEM approved fluid other fluids could be dangerous and could S 2 cause damage to the machine ES aS y Y e S z 9 Always check the voltage is correct for use with the machine the voltage E u S sA E E setting is printed on the serial label 8 35 5 E Re S 9 Always read the user guide before operating the machine smoke machines ES 2 B s need to be operated carefully to avoid risk E wes S S 1 AS s vs RS 2 9 Never touch the nozzle at the front of the machine the nozzle can stay hot for im S S SS 5 S S9 up to 10 hours ajs wel gs g ml ws Gm s um ON E S 9 Do not remove the cover or attempt to repair a faulty machine an authorized JE SS Te ERE JEM dealer should be contacted in the event of a faulty machine Always use smoke machines in well ventilated areas over use could affect s sufferers of asthma or other chest conditions E 9 amp a E 2 RON Do not use the machine if there is a faulty mains lead or plug this could be n 9 3 3 3 dangerous lt S T 3 49 a g Os 3 D ies 2 9 Never point the output directly at peoples heads this
7. have finished using the machine you should de press the stand by button and then turn the mains switch off If any problems occur when operating the ZR12 AL please refer to the trouble shooting guide MARTIN MANUFACTURING UK PLC PAGE 5 ZRI2 AL USER GUIDE Using The Remote Control Fog Button Timer Value Button Stand by Button Timer Engage Button z o z 5 ur 5 3 CONTROLLER Jem Power LED Timer Cycle LED Output Control Delay Time Control Run Time Control The ZR12 AL comes with a comprehensive controller that allows the user to manually fire the machine or set a well featured timer to operate the machine When the ready LED is lit on the top of the machine the remote becomes functional and the Fog button will operate the machine when pressed Sometimes a pre determined amount of smoke is needed and the ZR12 AL remote has a timer that will operate over a wide range of time periods The x8 timer value gives even greater flexibility when a longer delay and run time are needed PAGE 6 MARTIN MANUFACTURING UK PLC ZRI2 AL USER GUIDE Functions FOG BUTTON Will when the machine has reached operating temperature fire the machine when pressed and held STAND BY BUTTON This turns the machines electronics on and off TIMER VALUE BUTTON When the timer is being used the timer values can be adjusted by a factor of 8 i e a 5 second minimum run time becomes 40 seconds amp a 10 second delay
8. v em MANUFACTURED BY MARTIN MANUFACTURING UK PLC BELVOIR WAY FAIRFIELD INDUSTRIAL ESTATE LOUTH LINCOLNSHIRE LN11 OLQ TEL 01507 604399 FAX 01507 601956 USER GUIDE VERSION 1 4 v Jem Coo E Jem ZR12 AL UJ CJ ZRI2 AL MARTIN MANUFACTURING UK PLC ZRI2 AL USER GUIDE Fluids Suitable For This Machine Note The JEM warranty will be void if any fluid other then JEM approved fluid is used If other fluids are used there could be serious damage to the machine and the fluid may not of been tested for use in public areas 6 MON Regular DJ v Jem ff oS Pro Smoke Super v Jem p a a 88 Pro Smoke Studio v Jem Pro Smoke High Density v Jem MARTIN MANUFACTURING UK PLC ZRI2 AL USER GUIDE How To Contact Us Address Martin Manufacturing uk Plc Belvoir Way Fairfield Industrial Estate Louth Lincolnshire LN11 0LQ Telephone 44 0 1507 604399 Fax 44 0 1507 601956 Email jem a martin dk Website Http www jemsmoke com MARTIN MANUFACTURING UK PLC ZRI2 AL USER GUIDE ZRI2 AL USER GUIDE Notes User Guide Index Introduction Safety Machine Layout Getting Started Using The Remote Control Using The Analogue Link The ZR12 AL Ducting Kit Trouble Shooting
Download Pdf Manuals
Related Search