DIP/SOIC/TSSOP EEPROM Board Pro User Manual
Contents
1. C SPI Host Adapter and the Cheetah SPI Host Adapter to program their Serial EEPROM flash memory chips TOTAL PHASE DIP SOIC TSSOP EEPROM c 2814 Total Phase Inc uuw totalphase com Socket Board v2 20 Figure 1 EEPROM Socket Board 10 34 1 1 Features Flash and burn I C and SPI EEPROM and flash memories that are in any of these standard chip packages DIP8 SOIC8 or TSSOP8 Provide to target device 0 9 V 5 V power supply from the adapter or external power source Connect or disconnect Slave Select SS and change the polarity of SS e Gang Program multiple devices by using multiple socket board and programming adapter sets in parallel on the same host computer TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 1 2 What s Included The EEPROM Socket Board 10 34 comes complete with e EEPROM Socket Board 10 34 e 8 pin split ribbon cable 1 3 Flash Center Software The Flash Center Software is a free software package that allows engineers to quickly erase program and verify 1 C and SPl based EEPROM and Flash memory chips that are interfaced through Promira Serial Platform Aardvark I C SPI Host Adapter and or Cheetah SPI Host Adapter FLASH Genter ER ta ta TOTAL PHASE Figure 2 Flash Center Software 1 3 1 Features e Fast speeds programing e Gang programming support the Flash Center Software can program multiple devices in parallel by connecting to multiple Promira Se2. 34 offers three different sockets to interface with your memory chip DIP8 SOIC8 and TSSOP8 Please note that only one can be used ata time as they are all cross connected TOTAL PHASE DIP SOIC TSSOP EEPROM c 2814 Total Phase Inc uuw totalphase com Socket Board v2 20 Ci C2 C3 ecm es nn 1 2 PULL DOWN 2 3 PULL ss up 99 CONNECT R2 E fees Jao vi 1 2 Aardvark 2 4 amp amp amp TERE Figure 1 The EEPROM Socket Board 10 34 provides three different sockets for interfacing with your stand alone memory chip 2 1 Compatible Chip Sizes The three sockets of the EEPROM Socket Board are compatible with standard sized chip packages Figure 7 provides information about the supported sizes for all the sockets Please note that all measurements are in millimeters mm TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual Top View End View Side View 1 P A A E O E1 E N p m P He co s D D A 3 Gen O an D o D Figure 7 Diagrams of the supported package sizes Please note that the diagrams are not to scale Compatible chip sizes for each of the sockets available on the EEPROM Socket Board All measurements are in millimeters mm f ns s01ee rssors A Lead Tip to Tip Width E 7 94 6 00 6 40 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual Molded Package Width E1 D TOTAL PHASE DIP SOIC TSSOP
3. external source If the power source to the EEPROM Socket Boards is the adapter then the Promira platform Cheetah adapter or Aardvark adapter must be configured to send target power to the board This can be accomplished via the Rosetta Language 11 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual Bindings the Flash Center software the Control Center Software or the Cheetah GUI Software When powered on the board s Power LED will be lit 3 5 Cross Connecting Adapters When cross connecting two adapters the board must be powered on Otherwise results may be unpredictable If you experience problems please make sure that the Power LED on the board is lit 12 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 4 Programming a Device C SPI EEPROM and Flash memories can be programmed using the Flash Center Software in conjunction with Promira platform Aardvark adapter or a Cheetah adapter Detailed technical information about all these products can be found on Total Phase s website 4 1 Inserting and Removing Device To program a chip insert the chip into the appropriate socket Please note that all the sockets are cross connected so it is only possible to use one socket at a time Whenever handling chips always be sure to follow safe handling procedures to ensure that the chips are not damaged 4 1 1 DIP8 To insert a DIP8 chip simply align the pins with the socket and firmly press the chip into the s
4. EEPROM Board Pro User Manual 3 Connectors 3 1 34 pin Boxed Connector and 10 pin Boxed Connectors The sockets are connected to 34 pin boxed connector and to 10 pin boxed connectors which are located directly beneath it The 34 pin boxed connector Promira is used to connect the sockets to Promira Serial Platform to program the target device The 10 pin boxed connectors Aardvark 1 and Aardvark 2 are used to connect the sockets to Cheetah SPI Host Adapter or Aardvark I C SPI Host Adapter to program the target device The two 10 pin boxed connectors are cross connected so it does not matter which one is used In most cases you will only want to connect a single adapter to the EEPROM Socket Board at a time The second 10 pin boxed connector is available to connect to a protocol analyzer or to cross connect with another adapter for testing purposes For example an Aardvark adapter or a Cheetah adapter can be connected to the board through Aardvark 1 connector to program the memory chip At the same time a Beagle I C SPI Protocol Analyzer can be attached to Aardvark 2 connector to monitor the bus while the chip is being programmed to ensure that the data on the bus is correct 3 2 External Connector External JT Figure 8 The External Connector J1 provides the developer with a quick and easy way to interface or monitor any or all of the EEPROM Socket Board signals some of the signals on the board are available for external monitori
5. EEPROM Socket Board 10 34 TOTAL PHASE D DIP SOIC TSSOP EEPROM 4 b TOTAL ic 2814 Total Phase Wii totelphese con Socket Board v2 22 a PHASE r in I6 C Yerevan ONE te Supported products PROMI f REFIFIE Tooo ou ole Uj 4 Features e Programming of stand alone 1 C and SPI based EEPROM and Flash memory chips e DIP 8 socket SOIC 8 socket EEPROM Socket Board 10 34 TSSOP 8 socket User Manual v1 00 e Multiple voltage options November 17 2014 e Multiple SPI Slave Select options Summary The EEPROM Socket Board 10 34 allows a developer to flash and burn stand alone 1 C or SPI based EEPROM and Flash memory chips by using either Promira Serial Platform with I C SPI Active Level 1 application Aardvark C SPI Host Adapter or a Cheetah SPI Host Adapter as an interface from a Windows or Linux computer The EEPROM Socket Board 10 34 supports three different standard chip packages DIP8 SOIC8 and TSSOP8 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 1 Overview The EEPROM Socket Board 10 34 provides embedded systems engineers with an easy and cost effective method of programming I C and SPl based memory devices Using Total Phase s industry leading host adapters and software engineers can take full advantage of the Flash Center programming software along with the Promira Serial Platform with I C SPI Active Level 1 application Aardvark
6. R2 E aed Figure 11 The developer can connect or disconnect Slave Select SS pin as well as configure the polarity of SS on the board 4 4 1 Connecting SS Some SPl based memory chips do not require the use of the Slave Select pin In these cases the SS pin can be disconnected To do this simply remove the jumper from the SS Connect connector J3 4 4 2 SS Pull down Pull up Resistors The EEPROM Socket Board provides the ability to either pull down or pull up the Slave Select line depending on the requirements of the target device by using a jumper to short pins on J4 connector To pull SS down short pins 1 and 2 To pull SS up short pins 2 and 3 15 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 5 Legal Contact 5 1 Disclaimer All of the software and documentation provided in this manual is copyright Total Phase Inc Total Phase License is granted to the user to freely use and distribute the software and documentation in complete and unaltered form provided that the purpose is to use or evaluate Total Phase products Distribution rights do not include public posting or mirroring on Internet websites Only a link to the Total Phase download area can be provided on such public websites Total Phase shall in no event be liable to any party for direct indirect special general incidental or consequential damages arising from the use of its site the software or documentation downloaded fro
7. a easy way to connect the correct signals to the appropriate pins of the memory chip that is to be programmed The included 8 pin split cable can be used to connect the correct signal to the appropriate pin In the top left side of the board you will notice that there is a graphic representation of a chip with numbered pins from 1 to 8 Figure 10 Along both sides of the drawing are two banks of 4 pin headers These banks are connected to the eight pins of the chip in the socket The pins of the chip should be connected to the appropriate sources as described by the chip s datasheet Various sources are provided around the chip diagram Along the top of the chip are five pins for VDD and along the bottom of the chip are five pins for GND To the left of the chip are sources for the I C and SPI pins Each source is labeled along the left 14 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 4 3 Powering the Device To configure the power source to the memory select one of the four voltage options 3 3V VI gt and VLvI VExt on the VDD source connector JP1 4 3 1 External Power Source It is possible to use an external power supply to provide power to the target chip To use an external power source use a jumper to short the pins next to VExt position 4 on the VDD source connector JP1 Power should be applied to the VExt pins on the External connector J1 4 4 SPI Slave Select PULL SS DOWN PULL ss up SS CONNECT
8. d Linux support e Free software and royalty free API 1 5 Aardvark I C SPI Host Adapter The Aardvark I C SPI Host Adapter is an I C SPI adapter that is capable of communicating over 1 C from 1 KHz to 800 KHz and over SPI from 125 100 KHz to 8 4 MHz in master slave mode The Aardvark adapter is designed to communicate with C SPI based EEPROM and Flash memories It is a convenient tool to develop prototype debug and program I C SPI based systems Figure 4 Aardvark FC SPI Host Adapter 1 5 1 Features e 12C Master Slave signaling from 1 KHz to 800 KHz e SPI Master Slave signaling from 125 100 KHz to 8 4 MHz e General Purpose I O e Windows and Linux support TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual e Free software and royalty free API 1 6 Cheetah SPI Host Adapter The Cheetah SPI Host Adapter is a high speed SPI adapter that is capable of communicating over SPI from 100 KHz to 40 MHz The Cheetah adapter is specifically designed to communicate with high speed SPl based Flash memory It is an ideal tool to develop debug and program SPl based systems Figure 5 Cheetah SPI Host Adapter 1 6 1 Features e SPI Master signaling from 100 KHz to 40 MHz e Maximum throughput with no inter byte delays e User configurable timing delays e Windows and Linux support e Free software and royalty free API TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 2 Sockets The EEPROM Socket Board 10
9. m its site or any derivative works thereof even if Total Phase or distributors have been advised of the possibility of such damage The software its documentation and any derivative works is provided on an as is basis and thus comes with absolutely no warranty either express or implied This disclaimer includes but is not limited to implied warranties of merchantability fitness for any particular purpose and non infringement Total Phase and distributors have no obligation to provide maintenance support or updates Information in this document is subject to change without notice and should not be construed as a commitment by Total Phase While the information contained herein is believed to be accurate Total Phase assumes no responsibility for any errors and or omissions that may appear in this document 5 2 Life Support Equipment Policy Total Phase products are not authorized for use in life support devices or systems Life support devices or systems include but are not limited to surgical implants medical systems and other safety critical systems in which failure of a Total Phase product could Cause personal injury or loss of life Should a Total Phase product be used in such an unauthorized manner Buyer agrees to indemnify and hold harmless Total Phase its officers employees affiliates and distributors from any and all claims arising from such use even if such claim alleges that Total Phase was negligent in the design or ma
10. ng through the External connector J1 The two VExt pins allow a user to use an external power source to power the memory device Please refer to the Programming a Device section for more information 10 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 3 3 VDD Source Connector VDD SOURCE Figure 9 The EEPROM Socket Board provides to the target device 0 9 V 5 V from the adapter or from external source The VDD source connector JP1 has 4 jumpers options which configured the power source to the memory 3 3V VI gt VLvl and VExt To select one of these voltages simply use a jumper to short the pins next to the appropriate voltage on the VDD source connector 3 3V The power voltage to the memory is 3 3V The target power pins of the Promira platform Cheetah adapter or Aardvark adapter supply 5V to the board voltage regulator VTgt The power voltage to the memory is 3 3 V or 5V which is supplied directly from the target power pins of the Promira platform Cheetah adapter or Aardvark adapter VLvi The power voltage to the memory is 0 9 V 3 3 V which is supplied directly from the I O power pins of the Promira platform VExt The power voltage to the memory is from external 0 9 V 5 V power supply that is connected to the External connector J1 pins 13 15 VExt 3 4 Powering the EEPROM Socket Board The EEPROM Socket Board provides 0 9 V 5 V to the target device from the adapter or from
11. nufacture of its product 5 3 Contact Information Total Phase can be found on the Internet at http www totalophase com If you have support related questions then submit a support request at https www totalphase com support For sales inquiries please contact sales totalphase com 16 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual 2010 2014 Total Phase Inc All rights reserved 17
12. ocket To remove a DIP8 chip we recommend that a DIP extractor tool is used to prevent damage to the chip and its pins 4 1 2 SOIC8 and TSSOP8 Both the SOIC8 and TSSOP8 sockets are zero insertion force sockets and work on the same principle To insert a chip 1 Press down on the top of the socket to raise the contact pins 2 While pressing down on the socket carefully place the chip into the socket and make sure that the orientation of the chip is correct pin 1 should always be in the top left corner 3 Once the chip is in place release the top of the socket to allow the contact pins to drop and hold the chip in place At this point the chip should be held securely in place Please make sure that all the contact pins have made contact with the correct pins on the chip When removing the chip we recommend using a vacuum pickup tool to prevent damage to the chip and its pins 13 TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual To remove a chip 1 Press down on the top of the socket to raise the contact pins 2 Carefully remove the chip using a vacuum pickup tool or equivalent tool 3 Release the top of the socket 4 2 Connecting the Pins Since different chips have different pin configurations the EEPROM Socket Board includes 8 pin split ribbon cable to allow you to connect the pins to the correct sources J9 5 UDD p 1 J1 Figure 10 The Pin Board connector provides the developer with
13. rial Platforms Aardvark 1 C SPI Host Adapters and or Cheetah SPI Host Adapters on the same computer e Extensible device support the Flash Center Software has an extensible XML based memory device library By adding or modifying the XML descriptions of TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual target memory devices developers can instantly support almost any I C or SPI based EEPROM or Serial Flash memory 1 3 2 Minimum Requirements e Windows or Linux 64 or 32 bit Windows Windows 7 Windows 8 Windows 8 1 Linux Red Hat SuSE Ubuntu Fedora e One or more available high speed USB 2 0 ports One or more Promira Serial Platforms Aardvark I C SPI Host Adapters and or Cheetah SPI Host Adapters 1 4 Promira Serial Platform The Promira Serial Platform with I C SPI Active Level 1 application is an C SPI adapter that is capable of communicating over IC from 1 KHz to 1 02 MHz and over SPI from 31 KHz to 12 5 8 MHz in master slave mode The Promira platform is designed to communicate with I C SPI based EEPROM and Flash memories It is a convenient tool to develop prototype debug and program lC SPI based systems Figure 3 Promira Platform 1 4 1 Features e C Master Slave signaling from 1 KHz to 1 02 0 5 MHz TOTAL PHASE DIP SOIC TSSOP EEPROM Board Pro User Manual e Master Slave SPI signaling from 31 KHz to 12 5 8 MHz e Built in voltage level shifter e General Purpose I O e Windows an
Download Pdf Manuals
Related Search