cardo SHO-1 Manual EN
Contents
1. Check all laws and regulations that apply to your region before using the Product and be mindful that compliance with all laws and regulations is the user s responsibility Use the Product only where and in the manner that such devices are permitted by applicable law The Product should not be used in contravention of local state or federal laws and regulations Please check federal state and local laws and regulations before using your Cardo Product Use Product only where safe and avoid usage at gas stations fuel depots or around explosives Use with hearing aids and medical devices only after consulting a physician or specialist Make sure to install and mount the Productina stable manner HEALTH WARNINGS Hearing Loss Audio devices can cause hearing loss Employ care and avoid exposure to excessive volume levels that may damage or impair hearing or lead to hearing loss Permanent hearing loss may occur if Products are used at high volume for prolonged periods of time RF Signals Most electronic equipment is shielded from RF signals However certain electronic equipment may not be shielded against the RF signals emanating from your wireless equipment Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of about six inches or 16 cm to be maintained between a mobile phone or wireless device and a pacemaker to avoid potential interference with the pacemaker Be sure not to interfere with the f2. is busy while on a phone call intercom call with Channels A and B 1 8 intercom call or Click to Link call s cardo 5 5 RECEIVING INTERCOM CALLS If a paired unit tries calling you via Intercom the call will begin almost instantly 5 6 GROUP SIGNAL Q Send an instant message to all paired cardo SHO 1 units and XY scala rider G9 G9x units within a range of up to 350 m The recipients will hear a Signal voice announcement To reach a maximum number of riders the message is automatically forwarded to all paired cardo SHO 1 units within the recipient s range In this manner the total range is extended to up to 1 km ky amp amp amp AS ds As The transfer of wireless signals is influenced by multiple external _ factors Therefore please do not rely on the Group Signal for emergency purposes cardo SHO 11 Edo To connect your cardo SHO 1 to a Bluetooth device you must first pair them Once paired they will automatically recognize each other whenever they are within range 10m 33ft Your unit has two Bluetooth channels for connection to mobile phones GPS devices and music players with A2DP 6 1 PAIRING BLUETOOTH CHANNELS 1 AND 2 1 Make sure Bluetooth is enabled on your phone GPS MP3 player 2 Check the unit is in Standby single BLUE flash every 3 seconds 3 To pair Bluetooth Channel 1 press for at least 5 seconds until the RED and BLUE LEDs b
3. 1 8 Buddies Click to Link with compatible models 1 on 1 spontaneous intercom conversations with random riders near you who are not already paired to your cardo SHO 1 5 171 8 INTERCOM TOGGLING Pair with up to 8 other devices 1 8 Buddies and connect with them one at a time by saying their name 5 1a CONFIGURING YOUR BUDDY NAME Before using 1 8 Intercom you should assign your device a Buddy Name so that other 1 8 participants can call you by this name If you change your Buddy Name you must pair again with your 1 8 Buddies for their device to receive your new Buddy Name Visit the Cardo Community to configure your Buddy Name see Section 3 Until you configure a Buddy Name your unit will be known by its generic 1 8 Buddy name cardo SHO 1 Hear Your Buddy Name Standby tap ana J simultaneously You will hear the Buddy name of your cardo SHO 1 through the speakers In Standby press O tor 2 seconds Play Paired Buddy List 8 cardo SHO 1 5 1b PAIRING WITH A 1 8 INTERCOM BUDDY 1 In Standby press O for 5 seconds to enter pairing mode 2 Repeat on the second cardo SHO 1 3 If pairing was successful a purple light appears for 2 seconds NOTES f your cardo SHO 1 already has a full list of 8 paired 1 8 Intercom Buddies pairing another buddy will replace the buddy that you have not spoken to for the longest time e For pairing
4. BREACH OF WARRANTY Such repairs or replacements will be made at no charge to the customer for parts or labor provided that the customer shall be responsible for any shipping cost This warranty does not cover failures due to abuse misuse accident or unauthorized alteration or repairs This Product is intended to be used only as a communication and entertainment device and should not be used in any location or jurisdiction where its use is prohibited The warranties and remedies contained herein are exclusive and in lieu of all other warranties express implied or statutory including any liability arising under any warranty of merchantability or fitness for a particular purpose statutory or otherwise that Cardo specifically disclaims This warranty gives you specific legal rights which may vary from state to state or from jurisdiction to jurisdiction Cardo makes no other warranties express or implied beyond those stated specifically herein This warranty is extended by Cardo solely to the original purchaser and is not assignable or transferable to others Cardo assumes no obligation or liability for additions or modifications to this warranty unless made in writing and signed by an officer of the company Batteries are warranted only if the battery capacity falls below 50 of rated capacity or if the battery develops leakage IMPORTANT Donotstore your Product without charging it from time to time for periods in excess of six months as this ma
5. coa ree UES 15 TO NOTICES corsario RU RI Ra 15 IMPORTANT This is version 2 0 of the User Manual Please note that our manual is periodically updated on the Cardo website to include the very latest features and functions of your new cardo SHO 1 Please visit www cardosystems com download manuals to check if the manual you are holding is the most updated version and to download the manual in your preferred language Thank you for choosing the cardo SHO 1 Bluetooth communication and entertainment system for Shoei helmets This manual will help you set up configure and operate it If you have purchased the cardo SHO 1 DUO your retail box contains two factory paired units Among others the cardo SHO 1 offers the following features INTERCOM OPTIONS e Intercom Conference mode between 2 3 or 4 riders at a range of up to 1 6 km e Click to Link Intercom For spontaneous connection with other riders nearby 1 8 Intercom Toggling with 8 additional buddies MULTIPLE DEVICE CONNECTIVITY e Bluetooth Mobile phones GPS device e Wireless MP3 connectivity via A2DP cable option also provided ENTERTAINMENT OPTIONS e Wireless music streaming via devices supporting Bluetooth Stereo A2DP and AVRCP profiles e MP3 Players non Bluetooth via cable e Built in FM Radio with 6 station presets and automatic tuning CARDO COMMUNITY e Download software upgrades enhancements and new features e Set up your 1 8 In
6. sure that the battery unit remains connected a Visit http community cardosystems com Minimum Requirements Windows XP Mac OS X 10 5 CARDO SMARTSET APP 4 Download on the a App Store ANDROID APP ON P gt Google play SETTINGS MENU The Settings menu is built in to your cardo SHO 1 and is available in several languages EnterMenu In Standby press BD for 2 seconds ExitMenu Press 2D for 2 seconds cardo 4 1 GENERAL FUNCTIONS Power ON OFF Press for 2 seconds e ON 3 BLUE flashes ascending tone e OFF 3 RED flashes descending tone Tap O or Oto adjust and set volume of current audio source Volume Mute Unmute Tap O and O simultaneously In Standby press O and O for 5 seconds e Blue LED Full charge e Purple LED Half charge e Red LED Almost empty Battery level indicator Enter Settings Menu In Standby press AD for 2 seconds and follow the spoken instructions en Your Buddy In Standby tap 2 and simultaneously ame Paired Device In Standby press BJ and for 2 seconds Indication If 1 8 Buddies are within range purple LEDs flash for 2 seconds Enable Disable VOX In Standby press O and O for 2 seconds For Intercom calls Enabled Blue flash for 2 seconds only Disabled Red flash for 2 seconds Enable Disable Press AD and Elorz seconds Spoken Status Announcements cardo SHO 1 5 ya cardo 4 2 STATUS LIGHTS 4 4 VOICE COM
7. to answer by VOX Reject a call Remain silent for 15 seconds or press AD for 2 seconds Voice Dial if supported by mobile phone from the mobile Reial Hot Dial Set default mobile Change default mobile INTERCOM CONFERENCE MODE Add Remove Channel A Tap Ld while on a phone call to from a call Add Remove Channel B Double tap while on a phone call to from a call This feature is not available during mobile calls t Before using Hot Dial configure your Hot Dial number via the Cardo Community or the Cardo Smartset App If 2 mobile phones are paired directly to your cardo SHO 1 set one to use as default for outgoing calls Answer a call 6 3 LISTENING TO MUSIC VIA A2DP The cardo SHO 1 can also receive audio via the enclosed cable from non Bluetooth MP3 Players or audio sources as described in section 6 5 Available only on AVRCP compatible Bluetooth audio sources In standby tap N Press 2h for 2 seconds With music ON tap ah With music ON double tap 0h With music ON press Q scans up or Q scans down for 5 sec The first few seconds of each track will play To stop the scan on the current track say any word loudly into the microphone or tap Bh With some phones you may need to repeat this action SWITCHING BETWEEN A2DP AUDIO SOURCES If a Music Player is paired the cardo SHO 1 will use it as the default A2DP audio source 1 Stop the music playback from the current de
8. with 1 8 Buddies using scala rider G9 G9x units see www cardosystems com sholcompatibility Pairing Online Cardo Community You can also find your friends and add them to your 1 8 Buddy list via the Cardo Community see section 3 5 1c PAIRED DEVICE INDICATION You can see which units within a range of 20m are your 1 8 Intercom Buddies In Standby press P and HM for 2 seconds If 1 8 Buddies are within range the LEDs on both units will turn PURPLE for 2 seconds Paired Device Indication 5 1d CALLING 1 8 INTERCOM BUDDIES There are two ways to start an intercom call with 1 8 buddies Q OPTION 1 Voice Connect VOX Speak any word loudly into the microphone When you hear the Voice Command tone say the name of a 1 8 Intercom Buddy i e John Smith eS OPTION 2 Manual Mode CHOOSE THE NAME AS from your Buddy List Press Ss for 2 seconds Hear the names of all pre paired 1 8 buddies When you hear the name of the Buddy you wish to call tap 9 or say any word loudly into the microphone Tap ana say the name of the 1 8 Buddy To cancel Buddy List playback Press e for 2 seconds 5 2 INTERCOM WITH CHANNELS A AND B Start multi party conversations using Intercom Channels A and B This mode is suitable for 2 3 or 4 way calls 5 2a PAIRING INTERCOM CHANNELS A AND B Pairing a Channel will replac
9. MAND Main unit LED indication Status The cardo SHO 1 allows you to perform key actions hands free by None caro SHO 1 is OFF simply using your voice 1 BLUE flash every 3 seconds Standby mode No active audio The default Voice Command language is English Other languages are also available see section 3 to adjust settings Active mode Call in progress l l 2 BLUE flashes every 3 seconds or other audio source is ON Throughout this manual features which are available via Voice Command are marked with the Q icon 1 RED flash every 3 seconds Standby mode Battery is low SEak E d Net dE ad 1 With no call in progress tap Bor speak any word loudly to asnes every 5 seconds ctive mode battery IS IOW activate VOX Solid PURPLE USB connected 2 Speak a Voice Command from the table below Solid RED battery LED Charging Current Mode Desired Action Say this 4 3 AUDIO SOURCES AND PRIORITIES ae ea ra 148 Intercom Call lt lt Bu ame gt gt If two connected audio sources try to play audio simultaneously Standby FM the cardo SHO 1 automatically determines which to play through ee Intercom call with AorB Call Intercom Standby Turn off FM Radio OFF the speakers based on the priority of the connected devices Higher Priority 1 Mobile Phone or GPS instructions 2 Intercom 3 A2DP Stereo Bluetooth audio 4 FM Radio Built in 5 AUX for corded connection i e Music Players Lower Priority GPS instru
10. aa O communication in motion E Bluetooth Recommended by SHOEI User Guide PREMIUM HELMETS 6 2 1 INTRODUCTI N corerdanosasin leia dl 3 2 CHARGING THE BATTERY senora aria cus 4 3 CUSTOMIZATION AND SETTINGS 4 A GETTING STARTED sossoorosmessidssass siso rapino sado 5 4 1 GENERAL FUNCTIONS socsvecavtcannconesopisaeresesoneedensncess 5 AZ TATUS EKORT Sad dat 6 44 VOICE COMMAND sospicsrcrararcjaraca rare 6 45 VOICE CONNEC EVO cas rorage cora setos oia 7 d INTERCONL vesccicaidrna ocasion 7 3 1 148 INTERCOM WOGGLING crecidas sussa nas none bolos 8 5 2 INTERCOM WITH CHANNELS A AND E vsepbieeiereiieeserouess 9 5 3 CLICK TO LINK CTL INTERCOM us ccveccnicesecsrevigersesiecsai 11 OLE SIONAL retro ad ie 11 5 RECEIVING INTERCOM CALLS aires ni Se os a seers 11 SO GROUP SIGNAL tice deece ecu RD O tas A neces 11 6 PAIRING AND USING A MOBILE PHONE GPS OR MP3 PLAYER conosco iii 12 6 1 PAIRING BLUETOOTH CHANNELS 1 AND 2 cccccccescesecssesans 12 6 2 MAKING AND RECEIVING PHONE CALLS es soares ddr 12 6 3 LISTENING TO MUSIC VIA A2DP svccsvncewses eoteses eoaeteseses 13 SA MUSIC SHARING serrar sretnes EKERN SIRERE EEEREN nA 13 6 5 LISTENING TO MUSIC VIA THE AUX osocccsescentavuseueracetacss 13 cardo SHO 1 HFM RADIO asas EA AAA tes 14 RADIO TUNING za pose papas ena Ere EE EPT E ENERE cas 14 7 2 AUTOMATIC RADIO TUNING corra 14 9 TROUBLESHOOTING satis ecl aw es 14 SUPPORT pars see e ai
11. ctions from Smartphone GPS Apps are prioritized like A2DP audio FM Radio Next Station Preset Next Station Previous Station Preset Previous Station o Incoming mobile phone calls interrupt ongoing intercom calls Incoming intercom calls will interrupt ongoing A2DP music e Click to Link Intercom and 1 8 calls have the same priority Click to Link requests will not interrupt any type of Intercom call in ps see Section 5 1 for details E A2DP audio priority can be configured to be higher than Intercom See section 3 to adjust settings 6 Cardo SHO 1 Voice Command performance may vary based on environmental conditions including driving speed helmet type and ambient noise For improved performance of the Voice Command feature minimize wind impact on the microphone by using the large microphone sponge and closing the visor 4 5 VOICE CONNECT VOX The cardo SHO 1 offers VOX technology for safe and hands free operation of some key functions You can set VOX to either start an intercom call or activate the Voice Command VOX Activation Speak any word loudly into the microphone Speak any word loudly into the microphone Reject a call Remain silent for about 15 seconds See section 3 to adjust settings High Use this setting if it is difficult to activate VOX Low Use this setting if it is too easy to activate VOX VOX Sensitivity Default Medium VOX can be set to acti
12. d by copyright laws They are not in the public domain Any partial or total reproduction translation and or dissemination without the prior written authorization by the Company are strictly prohibited Any rights not expressly granted herein are reserved cardo SHO 1 15 6 IMPORTANT SAFETY AND WARRANTY INFORMATION WAIVER AND GENERAL RELEASE WARNING Cardo Systems Inc Cardo or the Company notifies you that your complete and undivided attention is required when using a communication device the Product while riding Failure to avoid potentially hazardous situations could result in accident resulting in serious injury or death Cardo advises you to take all necessary precautions and remain alert to the traffic weather and all road conditions Donot perform pairing linking orsimilar operations while riding All publications areintended to address technical capabilities and should not be construed as encouraging the operation of Cardo s Productsin any mannerthatis unsafe or prohibited by law Exercise all due caution while using this Product and obey all applicable traffic laws Always ride and use the Product in a safe manner Do not become distracted by the Product while riding Always consider road traffic terrain and other conditions to maximize safety Do not operate the Product ifit becomes unsafe to do so In some regions or states the use of mobile communications systems is prohibited or restricted
13. e any existing paired device on that Channel with the newly paired device If you have purchased the cardo SHO 1 DUO both units are factory paired and configured to communicate via Channel A If for any reason you have to pair them again OR if you wish to pair a different unit to make Intercom calls proceed as follows 1 Check that all units are in Standby 2 Press bd for 5 seconds until the LED begins flashing rapidly indicating it is in Intercom Pairing mode see table below for channel pairing So 3 Enter Intercom Pairing mode on the second unit following its user manual Both units will now be in Intercom Pairing mode 4 After a few seconds both units will show a solid LED for 2 seconds indicating that they are paired and ready to use 5 If Pairing is not completed within two minutes the units will return to Standby mode CHANNEL PAIRING METHOD LED INDICATORS In Standby press So 5 seconds Rapid RED Channel A pairs automatically flashing In Standby press for 5 seconds Rapid BLUE When LED begins flashing tap Gl twice flashing 5 2b CALLING INTERCOM CHANNELS A AND B There are two ways to start an intercom call with Channels A and B Q OPTION 1 Voice Connect VOX Speak any word loudly into the microphone When you hear the Voice Command tone say Call Intercom to start an intercom call with A and or B subject to who is present VOX I
14. egin rapidly alternating To pair Bluetooth Channel 2 press O for at least 5 seconds until the RED and BLUE LEDs begin rapidly alternating To pair a GPS when LEDs begin rapidly alternating tap 4 Search for Bluetooth devices on your phone GPS MP3 player by following the device s instructions 5 After a few seconds the device will list cardo SHO 1 Select it 6 If prompted for a PIN or Passkey enter 0000 four zeros 7 The device will confirm that pairing has succeeded and the LED will begin flashing Blue once every 3 seconds 8 If pairing is not completed within 2 minutes the unit will return to Standby mode IMPORTANT e If you have paired 2 different mobile phones directly to your cardo SHO 1 you will need to set one as default for making calls e If your GPS supports it you can pair the second mobile phone directly to the GPS and then pair the GPS to your cardo SHO 1 and so connect both mobile phones and the GPS to your cardo SHO 1 12 Cardo SHO 1 NOTES e Not all Bluetooth mobile phones can broadcast Bluetooth Stereo music A2DP even if the phone has an MP3 player function Consult your mobile phone s User Manual for more information e Not all Bluetooth GPS devices allow connection to Bluetooth audio devices Consult your GPS User Manual for more information After pairing you may need to tap 0d to connect 6 2 MAKING AND RECEIVING PHONE CALLS Tap 19 or speak any word loudly
15. for this transmitter must not transmit simultaneously with any other antenna or transmitter except in accordance with FCC IC multi transmitter product procedures Industry Canada IC This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device IC RF Radiation Exposure Statement This equipment complies with the RSS 102 exemption from routine RF exposure evaluation for use in an uncontrolled environment European CE Notice Your Cardo product the Product is in conformity with the following essential requirements of Council Directive 1999 5 EC referred to as R amp TTE Directive Articles 3 1a 3 1 b and 3 2 The Product is manufactured in accordance with Annex Il of the above directive Declaration of Conformity DOC The Product is compliant with and adopts the Bluetooth Specification 3 0 Class 1 EDR and has successfully passed all interoperability tests that are specified in the B uetooth specification However interoperability between the device and other Bluetooth enabled products is not guaranteed Copyright The contents of this User Guide including all text illustrations and drawings are the exclusive intellectual property of Cardo Systems Inc the Company and are protecte
16. gns hereby voluntarily and forever release discharge indemnify and hold harmless Cardo from any and all litigation claims debts demands actions and liability which may arise directly or indirectly from using the Product for any distress pain suffering discomfort loss injury death damages to or in respect to any person or property however caused WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE and which may hereafter accrue to you on some future date as a result of said use to the fullest extent permitted by law 2 You fully understand and assume the risks in using the Product including risk of negligent acts or omissions by others All risks for operating the Product are assumed solely by the user of the Product 3 You confirm that you are physically capable to use the Product and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner You further confirm that you will not consume any alcohol that may affect your alertness or any mind altering substance and will not carry use or consume these substances before or during the use of the Product 4 You fully acknowledge our warnings and understand that a risks exist in using the Product while in traffic including but not limited to injury or illness strains fractures partial and or total paralysis death or other ailments that could cause serious disability b these risks may be caused by the negligence of the manufac
17. higher frequency from the current station and store the next 6 FM stations it discovers 3 If desired repeat to store the next 6 FM stations These 6 temporary stations cannot be saved and do not replace the O FM Presets you may have saved Turning off your cardo SHO 1 will clear the temporary stations and restore the FM Presets If your cardo SHO 1 stops responding reset it by turning Reboot it off and then on again press 4 for 2 seconds 1 In Standby press O for 5 secs until LED flashes RED BLUE 2 Press Bh for 2 seconds until LED flashes 5 times in PURPLE Reset Pairing Deletes all paired devices For additional information J www cardosystems com DK support cardosystems com EN USA and Canada 1 800 488 0363 International 49 89 450 36819 IMPORTANT MULTINATIONAL COMMERCE COMPANIES AND ONLINE AUCTION WEBSITES ARE NOT AUTHORIZED TO SELL CARDO PRODUCTS AND PURCHASES FROM SUCH SITES ARE AT YOUR OWN RISK TO RECEIVE WARRANTY OR CUSTOMER SERVICE YOU MUST SUBMIT ORIGINAL RECEIPTS FROM AUTHORIZED CARDO DEALERS PRODUCTS THAT WERE IMPORTED FROM NORTH AMERICA MUST BE SERVICED IN THE USA Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B d
18. igital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device FCC RF Radiation Exposure Statement This equipment complies with FCC IC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance The antenna used
19. in FM radio with a 6 Preset memory and RDS Radio Data System RDS allows your cardo SHO 1 to automatically retune to the strongest frequency available for the FM station you are listening to when the signal becomes too weak Turn on Radio In standby double tap 1d Turn off Radio Press 2h for 2 seconds Next Station With radio ON tap DO Previous Station With radio ON double tap MA RDS ON OFF Default Off With Radio ON press O and O simultaneously for 2 seconds 7 1 RADIO TUNING Preset stations can be saved via the Cardo Community the Cardo Smartset App or directly from your cardo SHO 1 1 Turn on the Radio 2 Select a Preset number you wish to set Preset 1 6 by tapping 0d until the desired preset is heard 3 Find an FM station to save using Seek or Scan Seek up down and Save Find the next FM station Choose a preset by tapping 0d Press O or O for 2 seconds Tap 0d within 20 seconds to save to current preset With Radio ON press O for 5 seconds To stop search tap O Tap 0h within 20 seconds to save to current preset To continue scan wait for the next station to be found Scan and Save Automatically scans up for a station 14 cardo SHO 1 7 2 AUTOMATIC RADIO TUNING This feature makes finding new stations fast and easy by automatically creating a temporary list of 6 radio stations 1 With the radio on press Q for 5 seconds 2 Your cardo SHO 1 will search upwards
20. lastic surfaces and all other externally exposed parts that are scratched or damaged after purchase Disclaimer of Warranty The device and its accessories are provided as is and as available without warranty of any kind beyond those assumed in the enclosed manual LIMITATION OF LIABILITY In no event shall Cardo be liable for any incidental special indirect punitive exemplary or consequential damages whether resulting from the use misuse or inability to use this product or from defects in the product or for any damages whatsoever resulting from the use of the product whether based on breach of contract tort including negligence product liability or otherwise even if advised of the possibility of such damages You acknowledge and agree that the limitations set forth above are fundamental elements of this agreement to which you consent and without which the product would not be provided to you absent such limitations Some jurisdictions do not allow certain exclusions of incidental or consequential damages so the above limitations may not apply to you Warranty Service To obtain warranty service your Product must be registered Register online at www cardosystems com registration Please present the Product along with your registration number bill of sale receipt at any authorized Service Center or at the store from which you have purchased the Product To obtain warranty service contact Cardo s product support and
21. nd e Intercom On 0f Music and Mobile cardo SHO 1 button layout Make sure that the battery is fully charged for at least 4 hours before initial use z ZT Zz LA a COS Charging with the wall charger is faster than via a computer USB port e BATTERY LED RED Charging RED LED OFF Charging complete In Standby press O and O for 5 seconds BLUE Full PURPLE Half RED Almostempty The cardo SHO 1 is waterproof and dustproof However when in use the USB silicone cover should be kept tightly closed to prevent moisture from entering the unit 4 cardo SHO 1 Get the most out of your cardo SHO 1 by changing the settings and customizing your unit according to your own personal preferences There are three ways to change the settings via the Cardo Community on a PC Mac the SmartSet App or from the Settings Menu on your device Cardo SmartSet Settings Community App Menu Set your Buddy name for 1 8 Intercom Add friends to your Buddy list Create and join tours and invite your friends Download the latest firmware upgrade Set your Hot Dial number Set the 6 FM radio presets Change the Voice Recognition language Disable Spoken Status Announcements Change A2DP Intercom audio priority Change AGC sensitivity for the speakers Change VOX Operation Mode Change VOX sensitivity for the microphone Disable Click to Link CARDO COMMUNITY WEB PLATFORM When connecting your cardo SHO 1 to the computer make
22. ntercom call with only A or B will end automatically after 30 seconds of silence wi OPTION 2 Manual Mode Use this to start an Intercom call with either e Channel A Tap e Channel B Double tap l To end a call tap If you are already in an Intercom call with A or B tap 6 twice to add a third rider A or B cardo SHO 1 9 gt cardo THREE WAY INTERCOM FOUR WAY INTERCOM Rider 2 Rider 3 Rider 1 Pairing Pairing Rider 1 is paired to Rider 2 and also to Rider 3 1 Rider 1 pairs to Rider 2 using Channel A see 5 2a 2 Rider 1 pairs to Rider 3 using Channel B see 5 2a 1 Pair Rider 1 to Passenger 2 using Channel A see 5 2a 2 Pair Rider 3 to Passenger 4 using Channel A see 5 2a 3 Pair Passenger 2 to Passenger 4 using Channel B see 5 2a In this configuration the two passengers numbered 2 and 4 are each using two Bluetooth connections IMPORTANT Three Way Conference Mode Considerations During a 3 Way Intercom Conference call with 2 other participants Calling Rider 1 will not be able to receive mobile phone calls or GPS navigation instructions as long as the call is in progress 1 Make sure all four units are in Standby 2 Passenger 2 should double tap to call Passenger 4 Wait until audio is heard on both units 3 Rider 1 should tap 4 to call Passenger 2 4 Rider 3 should tap 4 t
23. o call Passenger 4 IMPORTANT Four Way Conference Mode Considerations During a 4 Way Intercom call the two passengers who maintain two active connections will not be able to receive mobile phone calls or GPS instructions as long as the conference call is in progress 10 Cardo SHO 1 5 3 CLICK TO LINK CTL INTERCOM he ci E Click to Link is a spontaneous social feature of your SD cardo SHO 1 You can instantly initiate 1 on 1 intercom calls with other riders near you without being paired Think of it as a private channel that you can set up on the go with other riders that you see along the way Click to Link can be disabled effectively blocking any attempt by a third party to send a Click to Link request to you Start a CTL call request search lasts up to 10 sec Tap l three times End a CTL call Cancel a CTL call request Accept a CTL call When hearing the CTL ringtone Tap or say any word loudly to answer by VOX Reject a CTL call While hearing the CTL ringtone Remain silent until the ring tone stops or press for two seconds Via the Settings Menu Cardo Community and the Cardo Smartset App If other riders are nearby your next Click to Link call may randomly connect to any of them Enable Disable CTL Enabled by default 5 4 BUSY SIGNAL When attempting to establish an Intercom call with another device that is already busy a busy signal will be heard The cardo SHO 1
24. obtain an RMA tracking number or contact your local Cardo authorized dealer Ship securely with a copy of the original sales receipt which is required as proof of purchase for warranty repairs The RMA tracking number should be written on the outside of the package Send the Product freight charges prepaid to the Cardo address as directed by Cardo So Online Auction Purchases Online auction confirmations are not accepted for warranty verification To obtain warranty service an original or copy of the sales receipt from the original authorized retailer is required Cardo will not replace missing components from online auction sites WAIVER AND GENERAL RELEASE By using the Product you will waive substantial legal rights including the right to sue Please read the following carefully before using the Product By using the Product you are irrevocably releasing indemnifying from any liability loss claim and expense including attorney s fees and holding Cardo harmless for any bodily injuries harm or death as well as losses or damages in goods to any vehicles including your own or to any property or asset that belong to you or to third parties any of which may result from using the Product under any circumstances or conditions and irrespective of jurisdiction You confirm that this waiver and general release also applies to any and all third parties who recommend this Product 1 You your heirs legal representatives successors or assi
25. tercom buddies e Create find and join riding tours So e Customize your cardo SHO 1 settings ADVANCED TECHNOLOGY Voice Command and VOX technology e Make Receive mobile calls by voice command e Make intercom calls by voice command AGC technology Automatic Gain Control allowing the automatic volume adjustment according to ambient noise and riding speed You can also control the volume level manually AGC sensitivity levels can be customized to suit your personal preferences VOX technology and Voice Command for safe and hands free operation of key functions VOX sensitivity levels can be customized to suit your personal preferences PLC software Packet Loss Concealment for real time compensation of audio losses in challenging environments gt Software updates via the Cardo Community on PC Mac Cardo SmartSet App for settings customization on the go Spoken status announcements so that you always know to whom or to what device you are connected Volume Per Mode Volume is set and saved at different levels of your choice for each audio source We wish you a great cardo SHO 1 experience and encourage you to write us at support cardosystems com with any questions suggestions or comments you may have Under tough environmental conditions dense forest narrow buildings heavy traffic intercom range will be reduced Once conditions improve the range will increase again cardo SHO 3 Voice Comma
26. turers or its agents or any third party involved in the Product c these risks and dangers may arise from foreseeable or unforeseeable causes You hereby assumeall risks and dangers andall responsibility for any losses and or damages whether caused in whole orin part by the negligence or other conduct of others including Cardo 5 By using the Product you confirm that you have read this release of liability and fully understand and accept its terms and conditions www cardosystems com cardo SHO 1 17 Rs 18 Cardo SHO 1
27. unctionality of personal medical devices 16 Cardo SHO 1 Hearing Aids Some devices may interfere with certain hearing aids Inthe event of suchinterference you should consult yourhearing aid manufacturerto discuss alternatives Other Medical Devices If you use any other personal medical device consult the manufacturer of your device and or your physician to determine if it is adequately shielded from interference caused by external RF energy Your physician may be able to assist you in obtaining this information LIMITED WARRANTY Subject to compliance with Cardo s sales channel policy proper use of the Product and compliance with all applicable laws and regulations in your jurisdiction your Product is covered by a TWO YEAR limited product warranty from the date of original purchase Said original purchase must be supported by the retail sales receipt and your registration of the Product Subject to the aforementioned Cardo hereby represents that this Product is warranted to be free from defects in materials or workmanship proof of purchase and registration required Within the subject period Cardo will at its sole option repair or replace any components that fail in normal use Cardo retains the exclusive right to repair or replace with a new or newly refurbished replacement product the device or software or give a refund of the purchase price at its sole discretion SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY
28. vate the Voice Command default or to start an Intercom Call See section 3 to adjust settings VOX Operation Mode Enable Disable In Standby press O and O simultaneously for VOX For Intercom 2 seconds Voice Command e Enable Blue flash for 2 seconds only e Disable Red flash for 2 seconds o The cardo SHO 1 allows full duplex intercom communication ata range of up to 1 6 km 1 mile subject to terrain and within line of sight To chat with someone via Intercom first pair your cardo SHO 1 to the second unit Pairing is a one time process Once paired the units should automatically recognize each other whenever in range Ifyou have purchased the cardo SHO 1 DUO the box contains two factory paired units configured to communicate via Channel A Intercom Compatibility Your cardo SHO 1 is compatible with all Cardo intercom products Intercom range with other models is limited to the distance of the device with the shorter range For more info please visit www cardosystems com sho1compatibility Intercom communication is possible using one of the three Intercom modes cardo SHO 1 7 only Section Intercom with Channels Intercom Conferencing 2 way 5 2 A and B 3 way and 4 way using Channels with other scala rider A and B models 1 8 Intercom Toggling 2 way Intercom conversations between cardo SHO 1 within a group of up to eight other and scala rider G9 G9x
29. vice 2 Start music playback from the other device For best results when streaming A2DP make sure that your smartphone remains in close proximity to the main unit of the NM cardo SHO 1 Since this is on the left side of your helmet carry your smartphone on the left side of your body So 6 4 MUSIC SHARING Music sharing allows rider and passenger to listen to the Jd same music within a range of 10m 33 ft e Music sharing works only with A2DP Bluetooth stereo enabled audio sources In order to share your music with your riding partner your cardo SHO 1 unit SENDER needs to be paired to the other unit RECEIVER on CHANNEL A and the RECEIVER must be in Standby mode During A2DP music playback press O for 2 seconds Press O for 2 seconds Phone Intercom calls and GPS audio navigation will override music playback Music Sharing does not transmit voice audio and cannot be used as an Intercom call 6 5 LISTENING TO MUSICVIA THE AUX The USB AUX jack can be used to connect a non Bluetooth audio source with a 3 5 mm W stereo jack using the enclosed cable 1 Check that the cardo SHO 1 is in Standby 2 Connect the MP3 cable to the Music Player s jack and insert the other end of the cable into the USB AUX jack To listen to music from a cable connected device operate the Music Player using its buttons as usual FF REW PLAY PAUSE cardo SHO 1 13 Your cardo SHO 1 includes a built
30. y cause irreversible damage to the capacity of your battery Your warranty will not cover such events This warranty also becomes void if a any of the seals on the case or battery are broken or Product or battery show signs of tampering b the battery is used in equipment other than the equipment for which it was intended c the Product is used in contravention of its intended purpose d the Product was purchased from unauthorized resellers or online auctions Cardo assumes no responsibility resulting from the use of non Cardo components or products in conjunction with its Products and specifically the use of third party chargers or Bluetooth devices Furthermore Cardo is not responsible for any damage to any part of the Product resulting from the use of ancillary equipment not furnished by Cardo which is attached to or used in connection with the Product Not covered by the warranty 1 Defects or damage resulting from the use of this Product in other than its normal and customary manner 2 Defects or damage from misuse accident or neglect 3 Defects caused by improper operation maintenance installation adjustment or modification of any kind incl long term storage without periodic charging of the battery 4 Products opened disassembled or repaired by non authorized parties 5 Defects or damage due to exposure to excessive temperatures adverse weather conditions external impacts or spills of food or liquid 6 All p
Download Pdf Manuals
Related Search