Glacial 8LIECH-SC-SSF-SSS-NP Use and Care Manual
Contents
1. Hot amp Cold Hidden Bottle Water Cooler Model 8LIECH SC SSF SSS NP USER MANUAL TO REDUCE THE RISK OF INJURY AND PROPERTY DAMAGE USER MUST READ THIS MANUAL BEFORE ASSEMBLING INSTALLING amp OPERATING DISPENSER SAVE THIS MANUAL FOR FUTURE USE PN 5M009423X1 8LIECH SC SSF SSS NP 2012Electrotemp Technologies Inc SAFETY PRECAUTIONS To reduce risk of injury and property damage user must read this entire manual before assembling installing amp operating dispenser Failure to execute the instructions in this manual can cause personal injury or property damage This product dispenses water at very high temperatures Failure to use properly can cause personal injury When operating this dispenser always exercise basic safety precautions including the following Prior to use this dispenser must be properly assembled and installed in accordance with this manual This dispenser is intended for water dispensing only Do NOT use other liquids Do NOT use for other purposes Never use any other liquid in the dispenser other than known and microbiologically safe bottled water Warranty is void if used for any other liquids including coffee tea juices beer or wine For indoor use only Keep water dispenser in a dry place away from direct sunlight Do NOT use outdoors Install and use only on a hard flat and level surface Do NOT place dispenser into an enclosed space or cabinet Do NOT operate dispenser2. To avoid splashes hold cup as close to the tap as possible Depress right control downward to start flow Release control once desired fill level is achieved Dispense Hot Water A CAUTION This unit dispenses water at temperatures that can cause severe burns Avoid direct contact with hot water Keep children and pets away from unit while dispensing Never allow children to dispense hot water without proper and direct supervision Note After setup hot water will be available in 15 20 minutes Position bottle glass pitcher or cooking pot securely below hot water tap e The left triangle below the hot water control indicates the location of the hot water tap The circular shapes in the drip plate help align the flow of water This unit dispenses water at a fast rate To avoid splashes hold cup as close to the tap as possible Push hot water release button red inward and depress control downward to start flow Release control once desired fill level is achieved IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance Replace an Empty Bottle Notice When your bottle is empty the dispenser will beep intermittently and the LED nightlights will blink until a fresh bottle is connected You may also hear a sucking sound when the bottle empties This is normal and is another way to be alerted that your bottle is empty Replace empty bottle as soon as
3. Turn energy saving switches to OFF Unplug power cord from wall outlet Remove water bottle and probe from water bottle Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser A CAUTION HOT WATER Remove drain cap and silicon plug Cold water will immediately flow into the bucket Several seconds later hot water will dispense Reminder Place drain cap and silicon plug in a safe location so they are not lost Once unit has drained replace silicon plug and drain cap IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance 8 Remove remaining water from reservoir by dispensing from the cold tap into a pitcher Step B Sanitize Probe and Taps 1 Ina clean bucket make a sanitizing solution of 1 5 gallons of tap water and 3 tablespoons of unscented household bleach Wipe probe and area around all taps with a soft cloth moistened with the sanitizing solution Step C Sanitize Reservoirs Remove the cap from a spare empty 5 gallon bottle Fill the bottle with the water and bleach mixture Insert probe into bottle Slide bottle into cabinet and close door Plug power cord into a grounded wall outlet Turn energy saving switches ON Allow the water and bleach mixture to fill the empty reservoirs Wait 10 minutes then turn energy saving switches OFF and unplug the power cord O ON Oo PS ON oS Dispense 1 cup o
4. bottle Turn energy saving switches on back of dispenser to ON e The red switch controls the heating of water If you do not want hot water leave this switch OFF The blue switch controls the cooling of water If you do not want cold water leave this switch OFF Notice e For unit to operate properly the probe head must be seated on the bottle and the door must be fully closed It will take up to 3 minutes for the reservoirs to load During this time the pump will run on and off This is normal Each time you dispense water from the taps the pump will come on to refill the tanks This is normal IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance Initial Rinsing of Water Lines This unit has been tested and sanitized prior to packing and shipping During transit dust and odors can accumulate in the tank and lines You must dispense and dispose at least one quart of water prior to drinking any water Dispense Cold Water Note After setup it will take 1 hour to get water to maximum cold temperature During this time the compressor may run continuously This is normal Position bottle glass pitcher or cooking pot securely below cold water tap e The right triangle below the cold water control indicates the location of the cold water tap The circular shapes in the drip plate help align the flow of water This unit dispenses water at a fast rate
5. in the presence of explosive fumes Position back of dispenser no closer than 4 inches from wall and permit free airflow between wall and dispenser There must be at least 4 inches clearance on the sides of the dispenser to permit airflow Use only properly grounded outlets Do not use an extension cord with your water dispenser Always grasp plug and pull straight out from outlet Never unplug by pulling on power cord Do NOT use dispenser if cord becomes frayed or otherwise damaged To protect against electric shock do NOT immerse cord plug or any other part of cooler in water or other liquids Ensure dispenser is unplugged prior to cleaning Never allow children to dispense hot water without proper and direct supervision Unplug unit to prevent unsupervised use by children Service should be performed only by a certified technician Please contact us at 888 828 1426 for assistance IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance SAFETY PRECAUTIONS Electrical Requirements Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock A 120 volt 60 Hz AC only 15 amp fused electrical supply is required A time delay fuse or circuit breaker is recommended Do not overload t
6. clockwise Adjust in a single increment of 30 degrees of a circle the equivalent of 1 hour on a standard analog clock face Wait 1 hour for results If unsatisfactory adjust another 30 degrees clockwise wait then asses results Thermostat is located at back of unit Hot water is not hot It takes 15 20 minutes after setup to dispense hot water Make sure the power cord is properly connected to a working outlet Make sure energy saving switch is ON LED nightlights are flashing and dispenser is making beeping noises Replace empty bottle If unavailable leave door ajar or unplug cooler to stop beeping noise and flashing lights There may be an air leak Check air hose connections Dispenser is noisy Make sure dispenser is positioned on a level surface Water tastes bad Drain water from reservoirs and replace bottle with a fresh one Clean dispenser per Proper Care amp Cleaning instructions IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance LIMITED WARRANTY Electrotemp Technologies Inc Vendor warrants to the original purchaser of this dispenser and to no other person that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it then for a period of one 1 year from the date of purchase all parts in such dispenser shall be free from defects in material and workmanship Vendor may require reaso
7. dure step 8 only requires 3 minutes or until the pump stops 15 Complete the installation and operation instructions within this manual If your water has an off taste Do not return to store Call 888 828 1426 for assistance INSTALLATION Place dispenser upright Locate dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet Notice Do NOT plug in power cord yet Position dispenser so the back is at least 4 inches from wall and there are at least 4 inches of clearance on both sides To minimize vibration and noise make sure dispenser is level Notice Do NOT plug in power cord yet IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance OPERATION A CAUTION This dispenser is intended for water dispensing only Do NOT use other liquids Do NOT use for other purposes Warranty is void if used for any other liquids including coffee tea juices beer or wine This dispenser has been designed to use water bottles with a 3 5 or 5 2 gallon capacity Do NOT use alternative bottles Initial Set Up Do NOT plug in until steps 1 3 are completed 1 Allow unit to sit upright for 4 hours 2 This model uses an pump to force water from the bottle to the reservoirs a Please do the following i Clean bottle cap and neck i Remove entire plastic cap from bottle ii Adjust length of probe by pulling B portion of tube t
8. f the water bleach solution through each tap to clean out the water ways N o Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser ACAUTION HOT WATER Remove drain cap and silicon plug Cold water will immediately flow into the bucket Several seconds later hot water will dispense Reminder Place drain cap and silicon plug in a safe location so they are not lost 12 Once unit has drained replace silicon plug and drain cap 13 Remove remaining water from reservoir by dispensing from the cold tap into a pitcher Step D Rinse Reservoirs Dispose of the water and bleach mixture and rinse bottle with tap water Fill the bottle with tap water and insert probe into bottle Push down on probe until it is seated Slide bottle into cabinet and close door Plug power cord into a grounded wall outlet Turn energy saving switches ON IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance 7 Allow the water to fill the empty reservoirs 8 Wait 10 minutes then turn energy saving switches OFF and unplug the power cord 9 Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser ACAUTION HOT WATER Remove drain cap and silicon plug Cold water will immediately flow into the bucket Several seconds later hot water will dispense Reminder Place drain cap and silicon plug in a safe location so they are n
9. he ciruit provide separate circuit if required to serve only this appliance This water cooler is equipped with a power supply cord having a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong grounding type outlet grounded in accordance with local codes and ordinances a mating outlet is not available it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician If codes permit and a separate ground wire is used it is recommended that a qualified electrician determine that the ground path is adequate Do not ground to a gas pipe Check with a qualified electrician if you are not sure the water cooler is properly grounded Do not have a fuse in the neutral or ground circuit GROUNDING INSTRUCTIONS For a grounded cord connected water cooler This water cooler must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current This water cooler is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician o
10. istributors AFTER THE PERIOD OF THE ONE 1 YEAR EXPRESS WARRANTY VENDOR DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE FURTHER VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL INDIRECT PUNITIVE INCIDENTAL OR CONSEQUENTAL DAMAGES Vendor assumes no responsibility for any defects caused by third parties This Limited Warranty gives the purchaser specific legal rights a purchaser may have other rights depending upon where he or she lives Some jurisdictions do not allow exclusion or limitation of special incidental or consequential damages or limitations on how long a warranty lasts so the above exclusion and limitations may not apply to you Warranty is void if electrical outlet is improperly wired to incorrectly sized circuit breaker or fuse if not grounded properly or wires do not have correct polarity Electrotemp Technologies Inc 406 Watline Avenue Mississauga Ontario L4Z 1X2 888 828 1426 www electrotemp com IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance UDO DD DD DD 8SLIECH SC SSF SSS NP GLACIAL Engish O O O0 5M009423X 1 Doo Doo 000
11. nable proof of your date of purchase from an authorized retailer or distributor Therefore you should retain your sales slip or invoice The Limited Warranty shall be limited to repair or replacement of parts which prove defective under normal use and service and which Vendor shall determine in its reasonable discretion upon examination to be defective Before returning any parts you should contact Vendor s Customer Service Department using the contact information listed below If Vendor confirms after examination a defect covered by this Limited Warranty in any returned part and if Vendor approves claim Vendor will replace such defective part without charge If you return defective parts transportation charges must be prepaid by you Vendor will return replacement parts to original purchaser freight or postage prepaid The Limited Warranty does not cover any failures or operating difficulties due to accident abuse misuse alteration misapplication improper installation or improper maintenance or service by you or any third party or failure to perform normal and routine maintenance on the dispenser as set out in the User s Manual In addition the Limited Warranty does not cover damages to the finish such as scratches dents discoloration or rust after purchase The Limited Warranty is in lieu of all other express warranties Vendor disclaims all warranties for products that are purchased from seller other than authorized retailers or d
12. o its maximum 5 extension Insert probe into bottle and push down Probe will self adjust to appropriate length See illustration on right iv Push down on probe head until it is seated A vi Insert power plug into wall outlet b At initial start up it will take about 3 minutes for the reservoirs to load Install bottle B F Open door and place fresh bottle in front of tray Clean fresh bottle with a soft cloth and warm soapy water then rinse maximum extension HL 1 5 2 inches Remove entire plastic cap from top of bottle Insert probe into bottle Push down on probe until it is seated IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance NOTICE When using a 5 gallon rectangular bottle slide into place as shown in illustration below m Ub Plug cord into a properly grounded wall outlet e Water will be pumped into the hot and cold water reservoirs from the
13. ot lost Once unit has drained replace silicon plug and drain cap Remove remaining water from reservoir by dispensing from the cold tap into a pitcher Return the unit to its location install a fresh water bottle plug the power cord back into the grounded wall outlet and turn the energy saving switches ON IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance TROUBLESHOOTING Dispenser does not operate Make sure the power cord is properly connected to a working outlet Water is leaking Bottle may have a leak Remove bottle and replace with new bottle If leak remains remove probe from bottle and call 888 828 1426 for assistance Push buttons are stuck and or faucets are leaking Apply mineral oil baby oil to button slides to reduce friction No water is coming from the taps Make sure the bottle is not empty If so replace it If not adjust probe to an appropriate length Refer to page 7 point 2 for instructions Make sure to push the water controls in fully Make sure the probe connection with the water bottle forms a complete seal Make sure the door is closed Cold water is not cold It takes up to one hour after setup to dispense cold water Make sure the back of the dispenser is at least 4 inches from a wall and there is free airflow on all 4 sides of the dispenser Make sure energy saving switch is ON Adjust thermostat by turning
14. ove any odors or dust that may collect during shipment you must clean dispenser prior to first use Time Required 45 minutes Move dispenser away from wall and turn it 90 in either direction Turn power switches to OFF Unplug power cord from wall outlet Remove water bottle and probe from water bottle Place a 2 gallon or larger bucket under the probe assembly Dis assembly probe assembly wash probe parts by hand in soapy water or in the dishwater Romove filter and wash in soapy water Submerge probe hand in the soapy water and rinse properly maximum extension LL 1 5 2 inches Assemble back all parts of probe assembly spay dispensing nozzles of water faucets with chlorine solution 1 teaspoon of unscented bleach in one glass of water IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser ACAUTION HOT WATER Remove drain cap and silicon plug Cool water will immediately flow into the bucket Several seconds later hot water will dispense Be mindful to avoid injury 12 Once the unit has drained replace the silicon plug and drain cap 13 Remove the remaining water from the reservoirs by dispensing from the cold tap into a pitcher Rinsing 14 Repeat steps 2 to 13 but this time using clean tap water During the rinsing proce
15. r serviceman if you are in doubt as to whether the appliance is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician Please make sure that ELECTRICAL OUTLET IS PROPERLY WIRED TO CORRECT SIZED CIRCUIT BREAKER OR FUSE AND PROPERLY GROUNDED MUST BE WIRED TO HAVE CORRECT POLARITY IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance TABLE OF CONTENTS Safety Precautions Safety Precautions Electrical Requirements Key Information for Future Use Specifications Parts amp Features Assembly Cleaning Prior to Initial Use Installation Operation Proper Care amp Cleaning Troubleshooting Limited Warranty KEY INFORMATION FOR FUTURE USE Please register your dispenser immediately at www electrotemp com For future support please record your serial number located on label on back of dispenser and date purchased Staple your receipt to manual You will need this information to obtain warranty service Product Hot amp Cold Hidden Bottle Water Cooler Model Number 8LIECH SC SSF SSS NP Serial ID Number Date of Purchase IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance SPECIFICATIONS Power Supply 5Amp Refrigerant Type R 134A Cold Water Power lt 100Watt
16. s Cold Capacity Peak Hour 1 Gallon 3 79 L Cold Temp Range 3 C 10 C 37 4 F 50 F Hot Water Power 425 Watts Hot Capacity Peak Hour 1 Gallon 3 79 L Hot Temp Range 80 C 92 C 176 F 197 6 F Dimensions 102 8 cm x 32 cm x 38 2 cm 40 8 inch x 12 6 inch x 15 inch Net Weight 35 3 Ibs 16Kg PARTS amp FEATURES ENERGY STAR Control Hot Water O Hot Water Release O Control Cold Water O Hidden faucet Hot water 2 Hidden faucet Cold water O LED Nightlights O Drip Tray O Door Bottle Tray O Hot Power Switch Energy Saving Cold Power Switch Energy Saving 19 Carry Handle Cooling Thermostat Drain Plug Bottle Probe 15 Door Switch Water pump Power Cord Condenser IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance ASSEMBLY Keep plastic bags away from children AARARANAN Remove dispenser from packaging Unpack drip tray and insert into dispenser Remove protective packaging from around probe Properly dispose all of packaging CLEANING PRIOR TO INITIAL USE To rem
17. you notice it is empty If unavailable leave door ajar or unplug cooler to stop beeping noise and flashing lights There may be a small amount of water left in the bottle This is normal if you need assistance please contact customer service Open door and slide bottle out Remove probe from bottle e Pull probe straight up until completely out of bottle Install fresh bottle Place fresh bottle in front of tray Clean fresh bottle with a soft cloth and warm soapy water then rinse Remove entire plastic cap from top of bottle Insert probe into bottle Push down on probe until it is seated Slide bottle onto tray and close door completely IMPORTANT Do NOT Return Dispenser To Store If you have a question or problem please contact 888 828 1426 for assistance PROPER CARE amp CLEANING General Cleaning Perform As needed Time Required 5 minutes Note Do NOT use abrasive materials or chemical cleaners Clean cabinet surfaces with a soft cloth and warm soapy water Wipe dust from back of dispenser to improve efficiency Remove drip tray assembly by sliding it forward Remove cover Place tray and cover in dishwasher or wipe parts clean with a soft cloth and warm soapy water Sanitizing Perform Every 3 months or whenever an off taste occurs Time Required 30 minutes Note Best to do prior to loading a fresh bottle Step A Remove Existing Water 1 Move dispenser away from wall and turn it 90 in either direction
Download Pdf Manuals
Related Search