STC-TGL2IR User`s Manual Toll Free Customer Support 1-888
Contents
1. PQI 32MB 64MB 128MB 256MB 512MB San Disk 32MB 64MB 128MB 2GB Panasonic 32MB 64MB 128MB Toshiba 32MB 64MB 128MB 256MB 512MB King Mate 32MB 64MB 128MB 256MB 512MB Lexar 256MB 512MB Kingston 128MB 256MB 512MB Kodak 128MB 256MB 512MB Dan Elec 128MB 256MB 512MB Viking 128MB PNY 128MB 256MB 512MB 2GB Proper camera operation cannot be guarantee when using memory card NOT listed above www wildviewcam com Toll Free 888 304 6125 STC TGL2IR Technical Specifications System Requirements and Compatibility e Windows 98 98se 2000 Me XP e Pentium III 450MHz or equivalent processor e 128MB SDRAM or above e VGA Video Card with 32MB RAM for minimum Color 16 bit or higher e An available CDROM driver and an available USB Port e 600 MB free hard disc space If you have any questions regarding your PC specifications please call your PC manufacturer www wildviewcam com Toll Free 888 304 6125 25 STC TGL2IR Camera Features and Specification Mega Built in Resolution Option Mode Pixel Memory High Low Video STC TGL2IR 2 0M 16MB 2 0M 1 3M_ QVGA e Auto white balance and auto expose e Auto On Off Infrared LED strobe control o Infrared Range 30ft e 4 digits LCD Image counter e Battery low indicator e Green Test LED indicator e Focusing 5 ft to Infinity e High precision multi layer glass lens with2. STC TGL2IR User s Manual Toll Free Customer Support 1 888 304 6125 www wildviewcam com Version 1 0 07 07 STC TGL2IR For Customer Service or Warranty Information Call Toll Free 888 304 6125 WILDVIEW P O Box 535189 Grand Prairie Texas 75053 5189 Wildview Limited Warranty Your Wildview scouting camera is covered by a 90 days Limited Warranty on parts and labor from the date of original purchase and purchases must be made through an authorized dealer The warranty covers defects in workmanship and materials The warranty does not apply to units which have been damaged or abused intentionally or unintentionally A purchase from individuals or unauthorized internet sites voids the warranty Tampering with or altering the unit will void the warranty Any unauthorized service will void warranty Original sales receipt must be produced for any warranty service and a Return Authorization RA number must be obtained from customer service at 888 304 6125 prior to returning product www wildviewcam com Toll Free 888 304 6125 2 STC TGL2IR Manual Contents Camera overview 4 Camera kit contents 6 Battery and memory Installation 6 Definition 10 Programming 11 Mounting the camera 14 Viewing images 18 Saving and Deleting images 21 Memory compatibility chart 24 Technical Specs 25 General Information 28 Image Capacity Chart 30 www wildviewcam com Toll Free 888 304 6125 STC TGL2IR Camera overview Front view Side
3. Start button and choose Run and then browse the CD drive and click Setup Viewing the images on your computer e Slide the power switch to OFF position e To view the images simply plug one end of the USB cable into an available USB port on your computer e Plug the other end of USB cable into the camera The camera will automatically power ON Front LCD screen will show USb e At the same time your computer will recognize the camera as a mass storage device and will be found under MY COMPUTER www wildviewcam com Toll Free 888 304 6125 20 STC TGL2IR Saving and Deleting images SAVING IMAGES To save images on to your PC simply copy and paste or drag and drop from the SDRAM memory to your PC desk top DELETING IMAGES There are two ways to delete the images from the internal SDRAM memory 1 After you down load the image onto your desk top you can delete the image in the SDRAM Unplug the USB Cable from camera Slide the power switch to PIR position LCD screen will display the number of images captured in the memory o Delete One picture a Press SET button to enter delete setting Display will show ESC b Press UP or DN to select d ONE delete one c Press SET to delete the image Press UP www wildviewcam com Toll Free 888 304 6125 21 STC TGL2IR or DN until screen shows ESC then press SET again to exit d This will only delete the last image saved in the
4. Scouting Camera s features is the ability to test the coverage area e After mounting the camera open front housing and slide the power switch to Test position The front LCD will display the word tESt e Close the front housing e Walk around in the front of the camera to see if you have mounted the camera in the proper position A green indicator light on the front will blink when you have intruded the coverage area e Adjust the camera position as needed and repeat testing until the desired coverage area is achieved www wildviewcam com Toll Free 888 304 6125 16 STC TGL2IR e When you have completed testing the coverage area open the front housing and slide the power switch from Test position to PIR position Front LCD counter will show 0000 The camera will enter count down mode for 1 minute and the front green indicator will start blinking giving you one minute to leave the coverage area Then camera will enter PIR detection mode NOTE Make sure you slide the power switch from TEST mode to PIR mode before you leave the field Otherwise the Camera will not take any pictures Switch use Do not move the switch from TEST directly to PIR Doing so will cause the camera to not operate Slide the switch to OFF Wait for the front LCD screen to turn off then continue to slide the switch to PIR www wildviewcam com Toll Free 888 304 6125 17 STC TGL2IR Viewing images Viewing images by computer download The
5. Wildview Scouting Camera is a plug and play USB storage device This means users of Windows 2000 ME and XP operating systems need not install the camera driver This camera is not MAC compatible The CD ROM included in this package contains the camera driver for older operating system only Attention The software CD ROM packaged with the camera is designed for PC s only not MAC compatible Playing this CD ROM on a stereo or CD player may cause damage to it Driver installation e Unplug the USB cable from PC e Insert the CDROM in CD driver of your PC e The auto run program will execute www wildviewcam com Toll Free 888 304 6125 18 STC TGL2IR e Follow the instructions shown on screen from your PC to completely install the driver and application program e If the existing DirectX version on your PC is lower than version 8 and if you have problems viewing the image with the standard software provided by Microsoft then you should install DirectX 8 e Restart windows e Turn off the camera e Connect your camera to the PC by the USB cable the PC will recognize the new device and set up the configuration of the PC automatically Front LCD on your camera will show the word USb NOTE Windows 98 users must install camera driver prior to connecting the USB cable www wildviewcam com Toll Free 888 304 6125 19 STC TGL2IR PC with USB Port e f your computer doesn t run automatically please click
6. be performed before you turn on the camera 1 Select the time out interval by sliding the time out toggle switch to the desired preset time interval in minutes 1 5 10 20 minutes 2 Select the resolution setting by sliding the resolution toggle switch to the desired resolution setting Hi Lo resolution 3 Select the Infrared mode Slide the switch to either Auto On Off position a Auto Infrared LED on based on surround light conditions b On Infrared LED on for every image captured c Off No Infrared LED will go off www wildviewcam com Toll Free 888 304 6125 11 STC TGL2IR 4 Select Burst mode Slide the switch to 1 2 3 AVI position 5 Turn onthe Camera to set the Date Time stamp a b Slide the power switch to the PIR position Press and hold SET button for 2 seconds to enter date amp time setting mode Time and HH will blink Press UP or DN to adjust the hour Press SET button to enter minute setting Time and MM will blink Press UP or DN to adjust the minute Press SET button to enter the month setting Date amp MM will blink Press UP or DN to adjust month Press SET button to enter date setting Date amp DD will blink Press UP or DN to adjust date Press SET button to enter year setting Date amp YY will blink Press UP or DN to adjust year www wildviewcam com Toll Free 888 304 6125 12 STC TGL2IR h Press and hold SET button f
7. memory o Delete All picture a Press SET button to enter delete setting Display will show ESC b Press UP or DN to select d ALL delete all c Press SET to delete all images The display will show DONE and will exit to count down mode automatically o Format a Press SET button to enter delete setting Display will show ESC b Press UP or DN to select Ft format c Press SET to confirm The display will show DONE and exit to count down mode automatically www wildviewcam com Toll Free 888 304 6125 22 STC TGL2IR o ESC To exit delete setting 2 Simply remove the batteries from the battery compartment This will delete the image stored in the internal SDRAM memory CAUTION Do not remove the battery until you have down loaded all the images in the internal SDRAM Once the battery is removed all images in the internal SDRAM will be deleted This does not apply to images stored in SD card RED LED indicator will blink when battery is low Turn off the camera Down load the pictures immediately DO NOT attempt to replace the batteries before you save the images in your PC Once the battery is drained completely or if you attempt to replace the battery all images in the internal SDRAM memory will be lost www wildviewcam com Toll Free 888 304 6125 23 STC TGL2IR SD card Compatibility Chart The following cards have been tested and approved for use in the STC TGL2IR model
8. coating e Effective viewing Angle 52 deg e PIR detection angle 48 deg e Low power consumption www wildviewcam com Toll Free 888 304 6125 26 STC TGL2IR o Standby current lt 2mA o Capture current lt 120mA Interface type USB 1 0 Power C size alkaline Batteries x 4 Image format Standard JPEG amp Motion JPEG AVI www wildviewcam com Toll Free 888 304 6125 27 STC TGL2IR General Information Storing conditions Operating Environment 14 to 104 deg F 10 to 40 deg C 20 85 relative humidity non condensation Special care instructions The camera is designed to be weather resistant Never attempt to immerse the unit in water or any other liquid This will damage the unit and void the warranty Use a soft lens cloth for cleaning lens Avoid touching lens with fingers Remove dirt or stains with a soft cloth dampened with water or neutral detergent Keep the Wildview scouting camera in a dry and cool dust free environment or container when it is NOT used Take the batteries out when the Wildview scouting camera is NOT to be used over a long period www wildviewcam com Toll Free 888 304 6125 28 STC TGL2IR e Avoid dropping the Wildview scouting camera on to hard ground Do not disassemble the Wildview scouting camera e Do not mix new and old batteries e Do not open the camera for unauthorized service This could cause serious damage to the unit and will void the warranty This camera is a
9. emory unless the expansion card is inserted at which point the front counter will only display the number of images stored in the expansion card www wildviewcam com Toll Free 888 304 6125 8 STC TGL2IR Inserting SD card Make sure camera is in the OFF position whenever adding or removing memory e Insert SD memory card in to the SD card slot completely and in the correct direction as shown on the inside of the housing e To remove the SD memory card depress the SD card and pull out the card gently SD cards must be clean no images from other sources www wildviewcam com Toll Free 888 304 6125 9 STC TGL2IR Definition Time out To set the amount of preset time in minutes the camera will sleep between PIR triggering Resolution The resolution selection that you have selected Model Hi Low STC TGL2IR 2 0M 1 3M Date Time To set date and time stamp in the picture Infrared Auto On Off mode Burst To set the number of pictures the camera will take per PIR triggering o 1P Single image capturing per PIR triggering o 2P Two images continuous capturing per PIR triggering o 3P Three images continuous capturing per PIR triggering www wildviewcam com Toll Free 888 304 6125 10 STC TGL2IR o AVI 10 second video clip per PIR triggering e FULL When memory capacity is full this front LCD screen will show FULL Programming your Wildview Camera The following setting must
10. nal battery compartment accepts 4 C cell batteries Be sure to use high quality brand name alkaline batteries Install batteries with correct polarity as noted inside the battery compartment 12V Lead Acid external battery The Wildview Scouting Camera is equipped with an external power jack designed to accept a barrel plug cable to attach to a sealed lead acid battery sold separately Battery cable and complete 12V Lead Acid battery kits are available wherever Wildview scouting cameras are sold or call toll free 888 304 6125 Only Wildview external battery accessories are recommended e Insert the battery pack plug into the DC 12V jack at the bottom of camera housing e Turn on the camera by sliding the power switch to PIR position www wildviewcam com Toll Free 888 304 6125 7 STC TGL2IR Please make sure the voltage and polarity are correct before connection Incorrect voltage or polarity will damage the camera Memory Options Your Wildview scouting camera is equipped with 16MB internal memory The camera is also equipped with an expandable media card slot capable of accepting up to 2GB SD card sold separately With no memory card inserted into the slot the camera will use the built in SDRAM memory to store images If an SD card is inserted into the slot then the camera will bypass the built in memory and utilize the SD memory The front counter display will show the number of images on the built in m
11. or 2 seconds to exit the setting mode and enter into PIR count down mode Display will show date and number of picture taken Once the program setting has been completed slide the power switch to OFF position until you are ready for field use NOTE Date amp Time setting will be lost whenever the batteries are removed from camera Don t forget to re set the Date amp Time stamp after you replace the batteries www wildviewcam com Toll Free 888 304 6125 13 STC TGL2IR Mounting the camera It is recommended that you mount the camera 4 5 ft off the ground with the camera pointed at a slight downward angle Be sure to avoid mounting the camera facing east or west as the rising and setting of the sun could produce false triggers and overexposed images Clear branches and other debris away from the front of the camera so as not to block the camera lens or PIR sensor EFFECTIVE DISTANCE 30 FEET HORIZONTAL PIR Coverage Area Diagram www wildviewcam com Toll Free 888 304 6125 14 STC TGL2IR Buckle Insert the strap through the strap slots on the rear housing Wrap the strap around the mounting surface Secure the strap and tighten the buckle in order to secure the camera www wildviewcam com Toll Free 888 304 6125 15 STC TGL2IR In order to obtain proper weather resistance please make sure that both door latches are securely locked in place Testing the camera coverage area One of Wildview
12. precision electronic device Do not attempt to service this camera yourself as opening or removing covers may expose you to dangerous voltage points or other risks Caution When camera is switched off if there is any residual power left in the camera it will take an extra picture to discharge the left over power in the camera Under low lighting condition the flash will go off www wildviewcam com Toll Free 888 304 6125 29 Image Capacity Chart STC TGL2IR SD card Built In 16MB SDRAM 16MB 32MB 64MB 128MB 256MB 512MB 1GB 2GB STC TGL2IR High 13 58 106 212 424 848 1696 3392 6784 Low 20 80 160 320 640 1280 2560 5120 10240 AVI 4 16 32 64 128 256 512 1024 2048 Subject to card compatibility under different brand www wildviewcam com Toll Free 888 304 6125 30 STC TGL2IR NOTE Image Capacity Chart provides approximate number of images or AVI movies based on resolution setting and the size of memory card These figures may vary depending on the amount of detail in the image US Patents 6 735 387 6 768 868 6 834 162 7 149 422 Patents Pending Product specifications are subject to change Wildview is not responsible for any photographic or typographical errors www wildviewcam com Toll Free 888 304 6125 31
13. view QOQQOOOO QQOOOOO OOOOOOO OCOOOOO www wildviewcam com Toll Free 888 304 6125 STC TGL2IR Open view image with major parts indication Battery Cover LCD Display Screen Passive Infrared Sensor PIR Test Indicator lt Frame Switch Picture Quantity Switch Camera sensor Switch Hh Time Switch Up Button Down Button Set Button mew gt ii www wildviewcam com CH Toll Free 888 304 6125 Camera Lens Low Battery Indicator SD Card Slot Infrared LED Infrared Control Switch Lock Hole 12 Volt DC Jack STC TGL2IR Camera kit contents STC TGL2IR Digital Scouting Camera Camera driver User Manual USB cable Strap Battery amp memory installation Warning Do not use a different Voltage lead acid battery other than the one specified in this section Doing so will damage the camera and will void the warranty The Wildview Digital Scouting Camera is designed to operate using alkaline batteries for optimum performance www wildviewcam com Toll Free 888 304 6125 6 STC TGL2IR NOTE Always have camera in the OFF position when installing or removing batteries Batteries C cell The inter
Download Pdf Manuals
Related Search