INNO POCKET Z4
Contents
1. BLND or LAST will be displayed beneath 2 Press ENTER and the bottom choice will begin to flash Use the UP or DOWN buttons to choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost e LAST If the DMX signal is lost the fixture will stay in the last DMX setting If power is applied and this mode is set the unit will automatically go into the last DMX set up e MASL Master Slave If the DMX signal is lost or power is applied the unit will automatically go into Master Slave mode and run a built in show e BLND Blackout If the DMX signal is lost or interrupted the unit will automatically go into stand by mode 3 Press ENTER to confirm your desired set up DIND This will let select your desired dimmer curve 1 Press the MENU button until DIND is displayed and press ENTER 1 of 5 dimmer curves will be displayed STDA stan dard STGE stage TV TV ARAL Architectural or THAL Theatre See the dimmer curve chart on page 28 for more info 2 Press the UP or DOWN buttons to find your desired dimmer Curve and press ENTER to confim and exit ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 13 Inno Pocket Z4 PINT Pan Inversion 1 Press the MENU button until PINT is displayed press ENTER Either Yes or No will be displayed 2 To activate the Pan inversion press2. ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 4 Inno Pocket Z4 When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g and appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Mounting Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself The installaiton should be checked by a skilled person once a year L Fa B ON H ON aaa The Inno Pocket Z4 is fully operational in three different mounting positions hanging upside down from a ceiling set on a flat level surface or on its side attached to trussing Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails see next page ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 5 Inno Pocket Z4 Mounting NOTICE The suitable enviromental temperature for this light ing fix
3. Sh X will now be displayed X representing a number between 1 4 Use the UP or DOWN buttons to find your desired show 3 When you have found your desired show press ENTER then press and hold the MENU button for at least 3 seconds to acti vate SOUN Sound Active mode 1 Press the MENU button until SOUN is displayed press ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to activate sound active mode or OFF to deactivate sound active mode 3 Press ENTER to confirm SENS In this mode you can adjust the sound sensitiv ity 1 Press the MENU button until SENS is displayed press ENTER 2 Anumber between 0 100 will be displayed Press the UP or DOWN buttons to adjust the sound sensitivity 0 being the least sensitive and 100 being the most sensitive 3 When you have found your desired setting press ENTER to confirm ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 12 Inno Pocket Z4 System Menu DNST This mode can be used as a precaution mode that in case the DMX signal is lost interrupted or power is lost the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost You can also set this as the operating mode you would like the unit to return to when power is applied 1 Press the MENU button until DNST is displayed and either MASL
4. Curve Chart side casing Dimmer 2 Use a brush to wipe down the cooling vents and fan grill 3 Clean the external optics with glass cleaner and a soft cloth every 20 days 100 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in 50 Inno Pocket Z4 Trouble Shooting Trouble Shooting Listed below are a few common problems that 10 you may encounter with solutions Trse Tdown R TS No light output from the unit voc tfc _ 08 Fade time waT 1 Be sure the external fuse has not blown The fuse is located on amp Effec E aa a the rear panel of the unit Standard 0 0 7 2 Be sure the fuse holder is completely and properly seated S x a R Unit does not respond to sound TV 1180 1520 1860 1940 Architectural ee arm 343 1 Low frequencies bass should cause the unit to react to sound Theatre 1580 1940 2230 2280 Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 28 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 29 Inno Pocket 24 Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects
5. self test MANU in this submenu you are able to test the different functions pan tilt LEDs zoom dimmer and strobe 1 Press the MENU button until MANU is displayed press ENTER 2 Use the UP and DOWN buttons to scroll through the various functions able for testing Once you have found your desired function you would like to test press ENTER 3 After you have pressed ENTER use the UP and DOWN but tons to adjust the values and test the function To exit press the MENU button TEMP with this function you can check the temperature of the fixture 1 Press the MENU button until TEMP is displayed press ENTER 2 The fixture temperature will now be displayed Press MENU to exit FHRS with this function you can display the running time of the unit 1 Press the MENU button until FHRS is displayed press ENTER ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 15 Inno Pocket Z4 System Menu 2 The running time of the fixture will now be displayed Press MENU to exit VER Use this function to display the Software version of the unit 1 Press the either the MENU button until VER is displayed press ENTER 2 The display will show the software version RS ET Use this function to reset the unit 1 Press the MENU button until RSET is displayed press ENTER 2 The fixture will now reset BALA With this function you can adjust the RGB colors t
6. setting find and set your desired operating mode 4 Onthe slave units press the MENU button until SLND is dis played and press ENTER Choose either SL 1 or SL 2 and press ENTER See page 11 for more info 5 The slave units will now follow the Master unit ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 19 Inno Pocket Z4 UC IR Operation The ADJ UC IR sold separately infrared remote gives you con trol of various functions See below To control the fixture you must aim the remote at the front of the fixture and be no more then 30 feet away STAND BY Pressing this button will blackout the fixture FULL ON Hold this button down to fully light up the unit When you let the button go the unit will return to its previous state FADE GOBO Press this button to activate Fade mode DIMMER and DIMMER Use these buttons to adjust the out put intensity in Color mode STROBE This button will activate the strobe effect Press and hold this button to activate strobing and release the button to stop strob ing COLOR Press this button to enter Dimmer mode Use the 1 9 but tons to select your desired color Adjust the output intensity using the DIMMER and DIMMER buttons 1 9 In color mode these buttons will allow you to select a desired color In show mode these buttons will allow you to select a desired show SOUND ON amp OFF These button
7. the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate Pan inversion select No and press Enter System Menu TINT Tilt Inversion 1 Press the MENU button until TINT is displayed press ENTER Either Yes or No will be displayed 2 To activate the tilt inversion press the UP or DOWN buttons until Yes is displayed press ENTER to confim To deactivate tilt inversion select No and press Enter LED with this function you can have the display back light turn off after 10 seconds 1 Press the MENU button until LED is displayed press ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to keep the LED display on at all times or OFF to switch to have the LED display switch off after 10 seconds 3 Press ENTER to confirm To make you LED display reappear again press any button DISP This function will reverse the display 180 1 Press the MENU button until DISP is displayed press ENTER 2 Press ENTER to flip the display Press ENTER to flip it ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 14 Inno Pocket Z4 System Menu again Press ENTER when you have made your desired setup TEST This function will run a self test program 1 Press the MENU button until TEST is displayed press ENTER 2 The fixture will now run a
8. 7715 User Instructions 02015 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 1 25 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when
9. CHANGING 192 255 COLOR FADING S 14 GOLOR CHANGE FADE SPEED 0 255 SLOW FAST COLOR MACRO 1 COLOR MACRO 2 0 255 ZOOM 10 60 16 COLOR MACRO 3 SHUTTER STROBE COLOR MACRO 4 0 7 CLOSED COLOR MACRO 5 8 15 OPEN COLOR MACRO 6 16 131 STROBING SLOW FAST COLOR MACRO 7 132 139 OPEN COLOR MACRO 8 140 181 FAST CLOSE SLOW OPEN COLOR MACRO 9 182 189 OPEN COLOR MACRO 10 190 231 SLOW CLOSE FAST OPEN COLOR MACRO 11 232 239 OPEN COLOR MACRO 12 240 247 RANDOM STROBING 248 255 OPEN E COLOR MACRO 15 18 SPECIAL FUNCTIONS COLOR MACRO 16 0 69 NO FUNCTION COLOR MACRO 17 70 79 BLACKOUT W PAN TILT MOVEMENT COLOR MACRO 18 80 89 DISABLE BLACKOUT WITH PAN TILT COLOR MACRO 19 MOVEMENT COLOR MACRO 20 90 199 NO FUNCTION COLOR MACRO 21 200 209 RESET ALL COLOR MAGRO 22 210 255 NO FUNCTION ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 22 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 23 Inno Pocket Z4 19 Channel Mode Inno Pocket Z4 22 Channel Mode Function Channel Value Function DIMMER CURVES a 0 255 _ PAN MOVEMENT 0 540 STANDARD 2 0 255 PAN FINE STAGE TILT MOVEMENT 0 180 U ae SO ie Eee 3 4 85 _ Green es a o 255 WHITE10 100 _ _ 9 0 255 RED20 100 COLOR MACROS NO FUNCTION COLOR MACRO 1 COLOR MACRO 2 COLOR MACRO 3 COLOR MACRO 4 COLOR MACRO 5 COLOR MACRO 6 COLOR MACRO 7 COLOR MACRO 8 COLOR MACRO 9
10. COLOR MACRO 10 COLOR MACRO 11 COLOR MACRO 12 COLOR MACRO 13 COLOR MACRO 14 COLOR MACRO 15 COLOR MACRO 16 COLOR MACRO 17 COLOR MACRO 18 COLOR MACRO 19 COLOR MACRO 20 COLOR MACRO 21 COLOR MACRO 22 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 24 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 25 Inno Pocket Z4 22 Channel Mode Inno Pocket Z4 22 Channel Mode Function Function COLOR MACROS SHUTTER STROBE 90 93 COLOR MACRO 23 132 139 OPEN 94 97 COLOR MACRO 24 140 181 FAST CLOSE SLOW OPEN 98 101 COLOR MACRO 25 182 189 OPEN 102 104 COLOR MACRO 26 190 231 SLOW CLOSE FAST OPEN 105 108 COLOR MACRO 27 232 239 OPEN 109 112 COLOR MACRO 28 240 247 RANDOM STROBING 113 115 COLOR MACRO 29 248 255 OPEN 116 119 COLOR MACRO 30 124 127 COLOR MACRO 32 0 255 FAST SLOW 128 191 COLOR CHANGING 21 SPECIAL FUNCTIONS 192 255 COLOR FADING 0 69 NO FUNCTION 70 79 BLACKOUT W PAN TILT MOVEMENT 0 255 SLOW FAST 80 89 DISABLE BLACKOUT WITH PAN TILT PAN TILT MACROS MOVEMENT 0 15 NO FUNCTION 90 199 NO FUNCTION 16 35 MACRO 1 200 209 RESET ALL 36 55 MACRO 2 210 255 NO FUNCTION 56 75 MACRO 3 DIMMER CURVES 76 95 MACRO 4 0 20 STANDARD 96 115 MACRO 5 21 40 STAGE 116 135 MACRO 6 41 60 TV 136 155 MACRO 7 61 80 ARCHITECTURAL 156 175 MACRO 8 81 100 THEATRE 176 195 MACRO 9 101 255 DEFAULT DIMMER SETTING 196 215 MACRO 10 216 235 MA
11. CRO 11 236 255 MACRO 12 16 PAN TILT MACRO SPEED U 255 SLOW FAST ZOOM 10 60 SHUTTER STROBE CLOSED OPEN STROBING SLOW FAST ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 26 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 27 Inno Pocket Z4 Photometric Chart Inno Pocket Z4 Fuse Replacement R 3510 958 435 243 160 Locate and remove the units power cord Once the cord has been Beam removed located the fuse holder located inside the power socket angle 10 ee 1077 Sas 140 Insert a flat head screw driver into the power socket and gently pry 5731 2581 1431 out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to OR 32 2 52 5 confuse the spare fuse with active fuse R B 46 20 17 15 T vaa ratr RGBW 1885 541 261 153 Due to fog residue smoke and dust cleaning the internal and exter nal optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environ ment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the out Distance m QO 1 0 2 0 3 0 4 0 5 0 Inno Pocket 24 Dimmer
12. WN buttons to adjust the sound sensitivity Press ENTER when you have found your desired sensi tivity level Show Mode This mode allows either a single unit or several units linked together to run one of four shows that you choose 1 Press the MENU button until SHND is displayed and press ENTER 2 Press the UP or DOWN buttons to find your desired show and press ENTER ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 18 Inno Pocket Z4 Master Slave Set Up Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units togeth er via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a termina tor at the last fixture 2 On the Master unit press the MENU button until SLND is dis played and press ENTER Use the UP and DOWN buttons to scroll to the MAST setting and press ENTER 3 After setting the Master unit to the master
13. X fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant Jo ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Inno Pocket Z4 can be controlled via DMX 512 proto col The Inno Pocket Z4 three DMX channel modes 16 channel mode 19 channel mode amp 22 channel mode The DMX address is set electronically using the controls on the front panel of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use stan 7 dard 110 120 Ohm shielded ca
14. ble This cable may l be purchased at almost all professional sound and Figure 1 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 7 Inno Pocket 24 DMX Set Up lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Male Socket XLR Female Socket I I I I 1 1 Ground I 2 Cold I I I I I I I I I I Figure 3 XLR Pin Configuration I I 2 Cold i 1 Ground Pin 1 Ground Pin 2 Data Compliment negative I I I Pin 3 Data True positive Special Note Line Termination When longer runs of cable are Used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cab
15. cket Z4 Instruction Manual Page 30 Inno Pocket Z4 Specifications Model Inno Pocket Z4 Voltage 100 240V 50 60Hz LED 4 x 10W 4 in 1 RGBW LEDs Power Consumption 67W Dimensions 5 5 L x 6 75 W x 9 75 H 141 x 174 x 247mm 7 Lbs 3 2 kgs 10 60 Degrees 3 15 Amp None 3 DMX Channel Modes 16 19 22 RGBW Color Mixing Sound Active Yes Working Position Any Safe Secure Position Warranty 2 Year 730 days Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On E facebook com americandj twitter com americandj youtube com adjlighting
16. ed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 1 Year 365 Days Limited Warranty excluding laser diodes which have a 6 month limited warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty batteries which have a 180 day limited war ranty Only the L E D s carry a 2 year warranty excluding StarTec Series which a carries a 1 Year Limited Warranty e ADJ DMX Controllers 2 Year 730 Days Limited Warranty excluding faders and tact switches ADJ Products LLC www adj com Inno Po
17. iday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 2 Inno Pocket Z4 General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Inno Pocket Z4 Features e DMX 512 Protocol Compatible 8 DMX Channel Modes 16 Chan nels 19 Channels amp 22 Channels 3 Operating Modes Sound Active Show Mode amp DMX Control 5 Dimmer Curves Standard Stage TV Architectural amp Theatre Internal Microphone Digital Display for Address and Function Setting 4 Preprogrammed Shows UC IR Compatiable Not Included Inno Pocket Z4 The Inno Pocket Z4 carries a 2 year 730 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www adj products com All returned service items whether under warranty or not mus
18. in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Product
19. irm Press the MENU button for one second to exit ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 17 Inno Pocket Z4 Operation Universal DMX Control This function allows you to use a Elatione universal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs 1 The Inno Pocket Z4 has 3 DMX channel modes 16 channel mode 19 channel mode and 22 channel mode See pages 21 27 for detailed description of the DMX values and traits 2 To control your fixture in DMX mode follow the set up procedures on pages 7 9 as well as the set up specifications that are includ ed with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the instruction on page 11 to set the DMX address For longer cable runs more than a 100 feet use a terminator on the last fixture For help operating in DMX mode consult the manual included with your DMX controller Or ge g Sound Active Mode This mode allows either single unit or several units linked together to run to the beat of the music 1 Press the MENU button until SOUN is displayed and press ENTER Press the UP or DOWN buttons so that ON is dis played and press ENTER 2 Press the MENU button until SENS is displayed and press ENTER Use the UP and DO
20. le terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems q and interference It is always advisable 7 to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 8 Inno Pocket Z4 DMX Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 9 Inno Pocket Z4 ADJ Products LLC System Menu DMX Address ST TA Slave Mode Sane Show Mode Sound Mode DMX Last State Dimmer Mode Back Light www adj com Inno Pocket Z4 Instruction Manual Page 10 Inno Pocket Z4 System Menu System Menu When making adjustments press ENTER to confirm your setup then press and hold the MENU button for at least 3 seconds To exit without making any adjust ments
21. not in use Thank you Inno Pocket Z4 General Information Unpacking Thank you for purchasing the Inno Pocket Z4 by ADJ Products LLC Every Inno Pocket Z4 has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for fur ther instructions Please do not return this unit to your dealer without contacting customer support first Introduction The Inno Pocket Z4 is a DMX intelligent zooming moving head mini LED fixture The Inno Pocket Z4 can operate as a stand alone fixture or in a Master Slave set up The Inno Pocket Zd has three operating modes sound active mode show mode DMX controlled This fixture is suitable for theaters studios retail stores and other similar locations For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Fr
22. o make your desired color 1 Press the MENU button until BALA is displayed press ENTER 2 Use the UP or DOWN buttons to find the color you wish to adjust 3 Once you find the color you want to adjust press ENTER the displayed value will begin to flash Use the UP or DOWN but tons to adjust the value Once you have made your adjustment press ENTER 4 Repeat steps 2 3 until satisfied ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 16 Inno Pocket Z4 Home Adjustment Menu U Pan Offset S S Tilt Offset F inc MENU pall _ To enter the home position adjustment menu unlock the dis play by pressing the MODE button for at least 3 seconds Then press the ENTER button for at least 3 seconds to enter the home adjustment menu In this submenu you are able to adjust the original position of the pan position and tilt position PINT Adjustment of the pan position 1 Press the ENTER button for at least 5 seconds then press the UP or DOWN buttons so that PINT is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit TINT Adjustment of the tilt position 1 Press the ENTER button for at least 5 seconds then press the UP or DOWN buttons so that TINT is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to conf
23. press the MENU button The display will lock after 30 seconds press the MENU button for 3 seconds to unlock ADDR DMX Address Setting 1 Press the either the MENU UP or DOWN buttons until ADDR is displayed press ENTER 2 The current address will now be displayed and flashing Press the UP or DOWN buttons to find your desired address Press ENTER to set your desired DMX address CHND This will let select your desired DMX channel mode 1 Press the either the MENU button until CHND is displayed press ENTER The current DMX channel mode will be dis played 2 Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confim and exit SLND This will let you set unit as a master or slave ina master slave configuration 1 Press the MENU button until SLND is displayed press ENTER Either MAST SL 1 or SL 2 will be displayed 2 Press the UP or DOWN buttons until your desired setting is displayed press ENTER to confim NOTE In a Master Slave configuration you can set one fixture to Master and then set the next fixture to SL 2 the fixtures will now have contrast movement to each other ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 11 Inno Pocket Z4 System Menu SHND Show modes 1 4 Show mode can run with or without sound active mode active 1 Press the MENU button until SHND is displayed press ENTER 2
24. rong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 29 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally or exhibits a marked change in performance
25. s LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether express
26. s activate and deactivate the sound active mode SHOW This activates the show mode Use buttons 1 4 to select your desired show ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 20 Inno Pocket Z4 16 Channel Mode Function Value 0 255 PAN MOVEMENT 0 540 PAN FINE TILT MOVEMENT 0 180 40 855 O ee 5 0 255 RED10 100 6 0 255 _GREEN10 100 8 0 255 WHITE 10 100 9 0 25 RED20 100 SHUTTER STROBE 0 7 CLOSED 8 15 OPEN 16 131 STROBING SLOW FAST 132 139 OPEN 140 181 FAST CLOSE SLOW OPEN 182 189 OPEN 190 231 SLOW CLOSE FAST OPEN 232 239 OPEN 240 247 RANDOM STROBING 248 255 OPEN SPECIAL FUNCTIONS 0 69 NO FUNCTION 70 79 BLACKOUT W PAN TILT MOVEMENT 80 89 DISABLE BLACKOUT WITH PAN TILT MOVEMENT NO FUNCTION RESET ALL NO FUNCTION 90 199 200 209 210 255 ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 21 Inno Pocket Z4 19 Channel Mode Inno Pocket Z4 19 Channel Mode Value Function Function 0 255 PAN MOVEMENT 0 540 13 COLOR MACROS 0 255 PAN FINE 90 93 COLOR MACRO 23 0 255 TILT MOVEMENT 0 180 94 97 COLOR MACRO 24 0 255 TILT FINE 98 101 COLOR MACRO 25 102 104 COLOR MACRO 26 0 _ 0 PRED 10 100 S 100 105 108 COLOR MACRO 27 0 _ 0 109 112 COLOR MACRO 28 113 118 COLOR MACRO 29 116 119 COLOR MACRO 30 120 123 COLOR MACRO 31 124 127 COLOR MACRO 32 128 191 COLOR
27. t be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ Products LLC customer support for a R A number Warranty Registration Inno Pocket Z4 Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 3 Inno Pocket Z4 Safety Precautions For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This p
28. ture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life r 1 Clamp V 2 Screw 3 Suspender 4 Safety screw 5 Safety rope Screw one clamp via a M12 screw and nut to the included bracket Attach the bracket using the included screws to the bottom of the Inno Pocket Z4 Attach the eyehole screw to the bottom of the base and pull the safety cable through the screw and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com Inno Pocket Z4 Instruction Manual Page 6 Inno Pocket Z4 DMX Set Up Power Supply The ADJ Inno Pocket Z4 contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DM
Download Pdf Manuals
Related Search