Home

EP830 User`s Manual VA1

1. 36 Hardware Description EP830 All In One EPIC Board User s Manual 3 5 Interrupt Controller The EP830 Series is a 100 PC compatible control board The mapping list under XP OS is shown as the following screen ima Pary check eror IRQO System timer output Cdr IRQ2 IRQ9 ACPIController_ Cd Dos EN Hardware Description 37 EP830 All In One EPIC Board User s Manual MEMO 38 Hardware Description EP830 All In One EPIC Board User s Manual Chapter 4 Award BIOS Utility The Phoenix Award BIOS provides users with a built in Setup program to modify basic system configuration All configured parameters are stored in a battery backed up RAM CMOS RAM to save the Setup information whenever the power is turned off 4 1 Entering Setup There are two ways to enter the Setup program You may either turn ON the computer and press lt Del gt immediately or press the lt Del gt and or lt Ctrl gt lt Alt gt and lt Esc gt keys simultaneously when the following message appears at the bottom of the screen during POST Power on Self Test TO ENTER SETUP PRESS DEL KEY If the message disappears before you respond and you still want to enter Setup please restart the system to try it again Turning the system power OFF and ON pressing the RESET button on the system case or simultaneously pressing lt Ctrl gt lt Alt gt and lt Del gt keys can restart the system If you do not press keys at the right
2. AK AXIOMTEK EP830 Series Intel Yonah amp Merom Core Duo and Core Solo All In One EPIC SBC With DVI I LCD and EPIC Express User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document AXIOMTEK does not make any commitment to update the information in this manual AXIOMTEK reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd CAUTION If you replace wrong batteries it causes the danger of explosion It is recommended by the manufacturer that you follow the manufacturer s instructions to only replace the same or equivalent type of battery and dispose of used ones Copyright 2007 AXIOMTEK Co Ltd All Rights Reserved November 2007 Version A1 Printed in Taiwan ESD Precautions Computer boards have integrated circuits sensitive to static electricity To prevent chipsets from
3. P Standard CMOS Features PPC Health Status gt Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password gt Power Ma Esc Quit F9 Menu in BIOS Select Item F10 Save amp Exit Setup To load CMOS SRAM with SETUP default values please enter Y If not please enter N Award BIOS Utility 65 EP830 All In One EPIC Board User s Manual 4 13 Set Supervisor User Password You can set a supervisor or user password or both of them The differences between them are 1 Supervisor password You can enter and change the options on the setup menu 2 User password You can just enter but have no right to change the options on the setup menu When you select this function the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type a maximum eight character password and press lt Enter gt This typed password will clear previously entered password from the CMOS memory You will be asked to confirm this password Type this password again and press lt Enter gt You may also press lt Esc gt to abort this selection and not enter a password To disable the password just press lt Enter gt when you are prompted to enter a password A message will confirm the password is getting disabled Once the password is disabled the system will boot and you can
4. 12V Pin 1 5V Pin 1 DCD Pin 1 Pin 8 12V Pin 8 5V o ojo 00000 15 Jumpers and Connectors EP830 All In One EPIC Board User s Manual O G o Been Q E ap Description 12V Pin 1 5V Pin 1 DCD Pin 1 Pin 8 12V Pin 8 5V Jumpers and Connectors 16 EP830 All In One EPIC Board User s Manual 2 3 9 Audio Line Out Speaker Out Jumper JP15 Line Out Default Jumpers and Connectors 17 EP830 All In One EPIC Board User s Manual 2 4 Connectors Connectors connect the CPU card with other parts of the system Loose or improper connection might cause problems Make sure all connectors are properly and firmly connected Here is a Summary table shows you all connectors on the EP830 Series Audio Connector Digital Visual Interface DVI Connector FAN L 6 S Serial Port2 Connector S S C 18 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 4 1 Power Control Connector CN1 COCA PWR_PSON 2 4 2 EPIC EXPRESS Slot CN2 Pin Description Pin Description 7 BPE DEO I BPE RXR GO 09 B PETXNO 10 BPERXNO A_CLKP E ou sey 28 ACN ar fe SS RESERVED Jumpers and Connectors 19 EP830 All In One EPIC Board User s Manual Pin Description Pin Description 79 RESERVED 8 EPERXNO 89 F PE RXP3 90 E PETXNG 2205 EPE RXR 9 EPETNI 99 F PE TXN3 100
5. 33 3 1 Microprocessors fre feta anclas 35 3 2 Ee 35 3 3 System MEMO dalt 35 3 4 VO Por Address ap wisn Ao 36 3 5 Interrupt Controller ii dci 37 Chapter 4 Award BIOS Utility aoocccconnnncnnnccoooconcccnnnnnccconananas 39 4 1 ENC FING SUD ie 39 4 2 GOMMOUK A O ea ees 40 4 3 Ge TEI Kee BENENE 2 OOO PO O sen Senment 40 4 4 The Main Men A oa eee 41 4 5 Standard CMOS Setup MenNU cccccccccccccncccncnononcnnnnnnnnonononononononononononoss 42 4 6 Advanced BIOS Features eiii ii 45 4 7 Advanced Chipset Features AANEREN 50 4 8 Integrated Peripherals unicidad 53 4 9 Power Management Geiup 58 4 10 PnP PCI Configuration S tup cccccccccccceccccecccceceeeceeeceseeeseeeeeneneeenens 62 4 11 PRA des 64 4 12 Load Optimized RE Susurros 65 4 13 Set Supervisor User Password 66 4 14 DAVE Sc EAS a beast 67 4 15 Exit VITRO UL S AVIING asias dais cada 68 Appendix A Watchdog Timer ccccccccesseeesseeesseeeseeeenseeeseeeees 69 Appendix B Digital Oil dais 71 MEMO VI EP830 All In One EPIC Board User s Manual Chapter 1 Introduction The All In One EPIC board EP830 Series supports Socket M 478 for Intel Yonah amp Merom Core Duo and Core Solo processors with FSB533 667MHz The board integrates Intel 945GME and ICH 7M chipsets that support one 200 pin DDR2 SDRAM with maximum 2GB system memory DVI I interface for both CRT and DVI external display devices dual Gigabit optional Fast Ethernet via
6. Controller Enable this item if you are using the USB in the system You should disable this item if a higher level controller is added gt USB 2 0 Controller Enable this item if you are using the EHCI USB2 0 controller in the system gt USB Keyboard Support Enable this item if the system has a Universal Serial Bus USB controller and you have a USB keyboard gt AC 97 Audio Select Use this item to enable or disable the onboard AC 97 Audio function Press lt Esc gt to return to the Integrated Peripherals page 56 Award BIOS Utility EP830 All In One EPIC Board User s Manual e Super IO Device Scroll to this item and press lt Enter gt to view the sub menu Super lO Device Phoenix AwardBIOS CMOS Setup Utility Super IO Device Item Help Menu Level gt gt Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 Onboard Serial Port 3 SE8 IRQ4 Onboard Serial Port 4 2E8 IRQ3 PWRON After PWR Fail Off Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults gt Onboard Serial Port 1 2 3 4 Select an address and corresponding interrupt for the serial port Options 3F8 RQ4 2F8 IRQ3 3E8 IRQ10 2E8 IRQ7 7 338 IRQ5 238 IRQ7 Auto and Disabled gt PWRON After PWR Fail This item enables your computer to automatically restart or return to its operating status Press lt Esc gt to return to the Integrated Peripherals page and pres
7. Without Saving Select this option to exit the Setup utility without saving changes you have made in this session Type Y and it will quit the Setup utility without saving your modifications Type N to return to the Setup utility Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features PC Health Status P Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password gt Integrated Peripherals Set User Password Quit Without Saving Y N Y Esc Quit F9 Menu in BIOS lt Select Item F10 Save amp Exit Setup 68 Award BIOS Utility EP830 All In One EPIC Board User s Manual AppendixA Watchdog Timer Watchdog Timer Setting After the system stops working for a while it can be auto reset by the Watchdog Timer The integrated Watchdog Timer can be set up in the system reset mode by program Using the Watchdog Function Start y Un Lock WDT O 2E 87 Un lock super I O O 2E 87 Un lock super I O y Select Logic device O 2E 07 O 2F 08 y Activate WDT O 2E 30 O 2F 01 y Set Second or Minute O 2E F5 O2FN N 00 or 08 See below table y Set base timer O 2E F6 O 2F M 00 01 02 FF Hex Value 0 to 255 y WDT counting re set timer O 2E F6 O 2F M M 00 01 02 FF See below table IF to disable WDT O 2E 30 O 2F 00 Can be disable at any time Watchdog Timer 69 EP830 All In One EPIC Board User s Manual e Timeout Valu
8. are CLK pn Mouse CLK 26 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 4 13 12V IN Power Connector ATX1 Connect the power cable to ATX1 for 12V ATX power supply which mainly supplies power to the CPU If the ATX1 power connector is not connected the system will not start ae Tee 2 4 14 Serial Port Interface Connectors COM1 COM2 COM3 COM4 The board has one onboard serial port COM1 RS 232 422 485 and three extensive serial ports COM2 4 RS 232 jumper selectable with auto flow control features The 5V 12V power can be used on DCD and RI for these four ports depending on the jumper setting comt 1 6 DSR Data SetReady 8 CTS ClearToSend_____ 9 RI Ringindicator______ Jumpers and Connectors 27 EP830 All In One EPIC Board User s Manual Pin Description Pin Description 4 Data Carrier o Data Set Ready Detect DCD DSR 3 Receive Data 4 Request to Send COM2 COM3 COM4 RXD RTS 3 21 00000 5 Transmit Data Clear to Send E TXD CTS Data Terminal Ready DTR ES Ring Indicator RI _9 Ground GND 10 NC 2 4 15 Digital Visual Interface DVI Connector DVI1 The EP830 Series has one connector that supports DVI CRT DVI1 is a DVI connector for the DVI CRT display DVI1 DVI CRT VGA Connector Pin Description Pin Description 5 CRT_SPD_Data 6 DVISPD Clock 7 DVISPD Data 8 AnalogVsyne 9 TMDSDatat 10 TMDSData
9. bd Y oo D om a a wg ru a ky ei ie e am na PA MO on pa od t Je Component Side Jumpers and Connectors 7 EP830 All In One EPIC Board User s Manual e 47 00 115 00 44 32 ooo coooo 00000 boa oa O Solder Side 8 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 3 Jumper Settings Proper jumer settings configure the EP830 to meet your application purpose We are herewith listing a summary table of all jumpers and default settings for onboard devices respectively Here is a list of jumper settings Short 1 2 Short 1 2 Short 1 2 Short 2 3 Short 1 2 Short 1 2 Short 2 3 Short 3 5 4 6 Short 3 5 4 6 Short 1 2 COM1 Mode Short 7 9 Select Short 8 10 COM2 Mode Short 7 9 Select Short 8 10 COM3 Mode Short 7 9 Select Short 8 10 COM4 Mode Short 7 9 Select Short 8 10 Short 1 3 2 4 Jumpers and Connectors 9 EP830 All In One EPIC Board User s Manual 2 3 1 CompactFlash Mode Selection Jumper JP1 Description Function Jumper Setting CompactFlash Slave Default Mode Selection 2 3 2 Power AT or ATX Selection Jumper JP2 This jumper let you select either AT or ATX power supply Description Jumper Setting Power Supply ATX POWER Selection Default 2 3 3 LVDS Voltage Selection Jumper JP3 This jumper is Le SSES the voltage for LVDS interface LVDS Voltage Selection 10 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2
10. connectors m Two IEEE 1394a ports e CompactFlash Socket One CompactFlash Type II Socket e Onboard Multi 1 O m 4 COM ports RS 232 e USB Interface Four USB ports with fuse protection and complies with USB Spec Rev 2 0 e Watchdog Timer m 1 255 seconds up to 255 levels D Introduction EP830 All In One EPIC Board User s Manual e Graphics 1 CRT output rear I O together with DVI output via CH7307 through SDVO B m 17 40 pin JST SHDR 40V S B connector for dual channel LVDS from LFP port and 1 7 pin inverter connector e Expansion Interface EPIC Express socket supported e Ethernet m 2 RIL8111B RTL8111C co layout for FE 10 100 1000 Base T via PCI Expres X1 m 2single deck RJ 45 e Audio AC 97 codec audio m Line in Line out and MIC in e Power Management m ACPI Advanced Configuration and Power Interface e Form Factor EPIC form factor on wy NOTE All specifications and images are subject to change without notice Introduction 3 EP830 All In One EPIC Board User s Manual 1 2 Utilities Supported Chipset Driver VGA Driver Ethernet Driver Audio Driver Introduction Chapter 2 Jumpers and Connectors Holes ixing EP830 All In One EPIC Board User s Manual PEPPERS EES ES Pee eee SPP SSPE PSSST eS Pe ee SSeS SSS e 0 98 dd LLL eee eee GAO dede dede ss ss D D we red KE SE EE O en END Board Layou
11. electrostatic discharge damage please take care of the following jobs with precautions Do not remove boards or integrated circuits from their anti static packaging until you are ready to install them Before holding the board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds It discharges static electricity from your body m Wear a wrist grounding strap available from most electronic component stores when handling boards and components Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co Ltd Windows is a trademark of Microsoft Corporation Phoenix amp AWARD are trademarks of Phoenix Technology Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation Winbond is a trademark of Winbond Electronics Corp Realtek is a trademark of Realtek Semi Conductor Co Ltd Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents BE Lu e ii EES iii Chapter 1 Introduction cin ar 1 1 1 ee te ten E 2 1 2 WINES UPPER 4 Chapter 2 Jumpers and Connectors scenerne 5 2 1 Board Layout and Fixing Holes EEN 5 2 2 Board DIMENSIONS EE 7 2 3 lu eege CG 9 2 3 1 CompactFlash Mode Selection Jumper JP 10 23 2 Power AT or ATX Selection Jumper JD 10 2 3 3 LVDS Voltage Selection Jumper Ip 10 2 3 4 USB Voltage Selection J
12. enter Setup freely PASSWORD DISABLED When a password is enabled you have to type it every time you enter the Setup It prevents any unauthorized persons from changing your system configuration Additionally when a password is enabled you can also require the BIOS to request a password every time the system reboots This would prevent unauthorized use of your computer You decide when the password is required for the BIOS Features Setup Menu and its Security option If the Security option is set to System the password is required during booting up and entry into the Setup if it is set as Setup a prompt will only appear before entering the Setup 66 Award BIOS Utility EP830 All In One EPIC Board User s Manual 4 14 Save amp Exit Setup This section allows you to determine whether or not to accept your modifications Type Y to quit the setup utility and save all changes into the CMOS memory Type N to bring you back to the Setup utility Phoenix AwardBlOS CMOS Setup Utility gt Standard CMOS Features gt PC Health Status gt Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Setup Saving Save to CMOS and EXIT Y N Y Esc Quit F9 Menu in BIOS gt lt Select Item F10 Save amp Exit Setup Award BIOS Utility 67 EP830 All In One EPIC Board User s Manual 4 15 Exit
13. power management values Blank Screen The System only writes blanks to the video buffer e Video Off In Suspend This ttem defines if the video is powered down when the system is put into suspend mode e Suspend Type If this item is set to the default Stop Grant the CPU will go into Idle Mode during power saving mode Award BIOS Utility 59 EP830 All In One EPIC Board User s Manual Moden Use IRQ If you want an incoming call on a modem to automatically resume the system from a powersaving mode use this item to specify the interrupt request line IRQ used by the modem You might have to connect the fax modem to the board Wake On Modem connector for working this feature Suspend Mode After the selected period of system inactivity 1 minute to 1 hour all devices except the CPU shut off The default value is Disabled Disabled System will never enter SUSPEND mode 1 2 4 6 8 10 2 Defines the continuous idle time before the system entering SUSPEND mode 0 30 40 Min 1 Hr If any item defined in J is enabled amp active SUSPEND timer will be reloaded HDD Power Down If HDD activity is not detected for the length of time specified in this field the hard disk drive will be powered down while all other devices remain active Suspend Mode After a selected period of system inactivity 1 minute to 1 hour all devices except the CPU shut off The default value is Disabled Disabled The System will n
14. system s RTC realtime clock Reload Global Timer Events Global Timer power management events can prevent the system from entering a power saving mode or can awaken the system from such a mode Primary Secondary IDE 0 1 Use this item to configure the IDE devices monitored by the system COM Port Use this item to configure the COM ports monitored by the system FDD COM LPT Port Use this item to configure the FDD COM and LPT ports monitored by the system PCI PIRQ A D This item can be used to detect PCI device activities if no activity the system will enter the sleep mode Press lt Esc gt to return to the Main Menu page Award BIOS Utility 61 EP830 All In One EPIC Board User s Manual 4 10 PnP PCI Configuration Setup This section describes the configuration of PCI Personal Computer Interconnect bus system which allows I O devices to operate at speeds close to the CPU speed while communicating with other important components This section covers very technical items that only experienced users could change default settings Phoenix AwardBlOS CMOS Setup Utility PnP PCI Configurations Init Display First PCI Slot Reset Configuration Data Disabled ltem Help Menu Level gt Resources Controlled By Auto ESCD PCI VGA Palette Snoop Disabled Maximum Payload Size 4096 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help FS Previous Values F7 Optimiz
15. the menu Enabled Enable cache Disabled Disable cache e Hyper Threading Technology Use this item to enable or disable Hyper Threading Technology which makes a single physical processor perform multi tasking function as two logical ones e Quick Power On Self Test This option speeds up Power on Self Test POST after you turn on the system power If set as Enabled BIOS will shorten or skip some check items during POST The default setting is Enabled e FirstSecond Third Boot Device These items let you select the 1st 2nd and 3rd devices that the system will search for during its boot up sequence The wide range of selection includes Floppy LS120 ZIP 100 HDDO 3 SCSI and CDROM e Boot Other Device This item allows users to enable or disable the boot device not listed in the First Second Third boot devices option above The default setting is Enabled e Onboard Lan Boot ROM Use this item to enable or disable the Boot ROM function of the onboard LAN chip when the system boots up e Boot Up NumLock Status Set the the Num Lock status when the system is powered on The default value is On Award BIOS Utility 47 EP830 All In One EPIC Board User s Manual e Gate A20 Option The default value is Fast The A20 signal is controlled by keyboard controller or chipset hardware Default Fast The A20 signal is controlled by Port 92 or chipset specific method e Typematic Rate Setting This item determi
16. time and the system doesn t boot an error message will pop out to prompt you the following information PRESS lt F1 gt TO CONTINUE lt CTRL ALT ESC gt OR lt DEL gt TO ENTER SETUP Award BIOS Utility 39 EP830 All In One EPIC Board User s Manual 4 2 Control Keys Main Menu Quit and delete changes into CMOS Esc key Status Page Setup Menu and Option Page Setup Menu Exit current page and return to Main Menu PgUp ke Increase the numeric value or make changes PgDn key Decrease the numeric value or make changes Fik General help only for Status Page Setup Menu and ey Option Page Setup Menu i Change color from total 16 colors F2 to select color Shift F2 key forward Shift F2 to select color backward F3 key Reserved F4 key ES k Restore the previous CMOS value from CMOS only 9 key for Option Page Setup Menu F6 k Load the default CMOS value from BIOS default R table only for Option Page Setup Menu Load the Setup default only for Option Page Setup F7 key Menu F8key Reserved F9key Reserved F10key Save all the CMOS changes only for Main Menu 4 3 Getting Help e Main Menu The online description of the highlighted setup function is displayed at the bottom of the screen e Status Page Setup Menu Option Page Setup Menu Press lt F1 gt to pop out a small Help window that provides the description of using appropriate keys and possible selections for highlighted items Press lt
17. types Type User for Enhanced IDE BIOS Press lt PgUp gt lt gt or lt PgDn gt lt gt to select a numbered hard disk type or directly type the number and press lt Enter gt Please be noted your drive s specifications must match the drive table The hard disk will not work properly if you enter improper information If your hard disk drive type does not match or is not listed you can use Type User to manually define your own drive type If selecting Type User you will be asked to enter related information in the following items Directly key in the information and press lt Enter gt This information should be provided in the documentation from your hard disk vendor or the system manufacturer If the HDD interface controller supports ESDI select Type 1 If the HDD interface controller supports SCSI select None If the HDD interface controller supports CD ROM select None CYLS number of cylinders LANDZONE landing zone HEADS number of heads SECTORS number of sectors PRECOMP write precom_____ MODE HDD access mode If there is no hard disk drive installed select NONE and press lt Enter gt e Video Select the display adapter type for your system Award BIOS Utility 43 EP830 All In One EPIC Board User s Manual e Halt On This ttem determines whether the system will halt or not if an error is detected while powering up The system booting will halt on any errors detected default Wh
18. 1 is a 44 pin IDE interface connector for standard 2 5 IDE device Pin Description Pin Description Pin Description 4 Daas 5 Daa6 6 Data 7 Daas 8 Datato 9 Data Data 11 12 Data 12 Data 1 18 zjaw esjow ajon 31 Interrupt 32 Nocomnector La 30 Jumpers and Connectors EP830 All In One EPIC Board User s Manual Pin Description Pin Description Pin Description HDC CS0 HDC CS1 HDD Active 5V ls jano 44 Nocomector IDE1 Jumpers and Connectors 31 EP830 All In One EPIC Board User s Manual 2 4 19 USB Port Connector USB1 The EP830 Series features Universal Serial Bus USB connectors compliant with USB 2 0 480Mbps that can be adapted to any USB peripherals such as monitor keyboard and mouse USB1 is a double deck USB port connector that consists of two 4 pin standard USB ports ston Pe toon DESS foo Le oo 2 4 20 USB Connector USB2 The Universal Serial Bus USB connector on the board is for the installation of peripherals supporting the USB interface USB2 is a 10 pin standard onboard USB connector Pin Descripion Pin pesenpnon rr ors ER REECH rr few e ew re few o eno Mi Bb 0 0 32 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 4 21 SATA Connectors SATA1 SATA2 The SATA connectors SATA1 and SATA2 are for high speed SATA interface port and it can be connected to serial ATA hard d
19. 3 4 USB Voltage Selection Jumpers JP4 JP7 This jumper is to select the voltage for USB interface USB Voltage 5V_SBY JP4 JP7 Selection 17523 5V Default JP4 JP7 2 3 5 CMOS Clear Jumper JP5 You may need to use this jumper is to clear the CMOS memory if incorrect setings in the Setup Utility CMOS Clear Normal Default Clear CMOS 2 3 6 CompactFlash Voltage Selection Jumper JP6 This jumper is to select the voltage for CompactFlash interface CompactFlash Voltage Selection Jumpers and Connectors 11 EP830 All In One EPIC Board User s Manual 2 3 7 GON Mode Selection Jumpers JP8 JP11 JP14 These jumpers select the COM1 port s communication mode to operate RS 232 or RS 422 485 Description Function Jumper Setting RS 232 Default 12 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 3 8 COM1 4 Mode Selection Jumpers JP9 JP10 JP12 JP13 These jumpers select the COM1 COM2 COM3 COM4 ports DCD and RI mode com Pinia o eu Pin 1 12V Pin 1 5V Pin 1 DCD Default Pin 9 12V Pin 9 5V Pin 9 RI Default Jumpers and Connectors 13 EP830 All In One EPIC Board User s Manual O G 0 Been Ou Q E ap Description 12V Pin 1 5V Pin 1 DCD Pin 1 Pin 8 12V Pin 8 5V Jumpers and Connectors 14 EP830 All In One EPIC Board User s Manual O 5 p p Been Ou Q E Description
20. DMA Select the mode of operation for the IDE drive Ultra DMA 33 66 100 133 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver If your hard drive and system software both support Ultra DMA 33 66 100 133 select Auto to enable UDMA mode by BIOS On Chip Serial ATA Setting gt On Chip Serial ATA Use this item to enable or disable the built in on chip serial ATA PATA IDE Mode Use this item to set the PATA IDE mode When set to Primary P1 and P3 are Secondary on the other hand when set to Secondary PO and P2 are Primary SATA Port If the PATA IDE Mode is Primary it will show P1 P3 is Secondary which means SATA 2 and SATA 4 are Secondary If the PATA IDE Mode is Secondary it will show PO P2 is Primary which means SATA 1 and SATA 3 are Primary Press lt Esc gt to return to the Integrated Peripherals page Award BIOS Utility 55 EP830 All In One EPIC Board User s Manual e Onboard Device Scroll to this item and press lt Enter gt to view the sub menu Onboard Device Phoenix AwardBIOS CMOS Setup Utility Onboard Device Item Help USB Controller Enabled Menu Level gt gt USB 2 0 Controller Enabled USB Keyboard Support Disabled AC97 Audio Select Enabled gt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults gt USB
21. E PE RXP1 End of EPIC EXPRESS Slot Pin Assignment Table 2 4 3 Power Output Connector CN3 rn bean o 20 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 4 4 LVDS Backlight Connector CN4 The 7 pin inverter connector on the EP830 is with Hirose connector The matching connector is strongly recommended to use Hirose DF 13 7S 1 25C Pin Description CN4 y 6 GND 0000000 Ai 2 4 5 JST Connector for LVDS Flat Panel CNS Pin Description Pin Description CN5 5 vccM 6 vcom 7 Ne a nc 9 GND 10 GND_ GND Channel B D1 19 Channel B D1 GND Channel B D2 5 Channel B D2 GND Channel A D3 Channel A D3 GND 34 GND Channel A CLK Channel A CLK GND l I d Su 90000000000000000 O LO K 00 NJOI 18 Jumpers and Connectors 21 EP830 All In One EPIC Board User s Manual 2 4 6 SMBUS Connector CN6 Connector CN6 is for SMBUS interface support Pin Description pg 2 4 7 IEEE 1394 Connectors CN7 CN10 Pin Description CN7 CN10 a 6 XTPBIN 12V i 7 12V 8 ug i 9 neo 22 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 4 8 Flat Panel Bezel Connector CN8 Power LED This 3 pin connector named as Pin 1 and Pin 5 connect the system power LED indicator to such a switch on the case Pin 1 is assigned as and Pin 5 as The Power LED lights up when the sys
22. F1 gt or lt Esc gt to exit the Help Window 40 Award BIOS Utility EP830 All In One EPIC Board User s Manual 4 4 The Main Menu Once you enter the Award BIOS CMOS Setup Utility the Main Menu appears on the screen In the Main Menu there are several Setup functions and a couple of Exit options for your selection Use arrow keys to select the Setup Page you intend to configure then press lt Enter gt to accept or enter its sub menu Phoenix AwardBlOS CMOS Setup Utility gt Standard CMOS Features gt PC Health Status gt Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password gt Integrated Peripherals Set User Password gt Power Management Setup save amp Exit Setup gt PnP PCI Configurations Exit Without Saving Esc Quit F9 Menuin BIOS Select Item F10 Save amp Exit Setup Time Date Hard Disk Type Y NOTE If your computer can not boot after making and saving system changes with Setup the Award BIOS will reset your system to the CMOS default settings via ts built in override feature It is strongly recommended that you should avoid changing the chipset s defaults Both Award and your system manufacturer have carefully set up these defaults that provide the best performance and reliability Award BIOS Utility 41 EP830 All In One EPIC Board User s Manual 4 5 Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic in
23. I VGA or not When enabled a PCI VGA can work with a MPEG ISA VESA VGA card when disabled a PCI VGA cannot work with a MPEG ISA VESA Card PCI Express relative items Maximum Payload Size When using DDR SDRAM and Buffer size selection another consideration in designing a payload memory is the size of the buffer for data storage Maximum Payload Size defines the maximum TLP Transaction Layer Packet data payload size for the device Press lt Esc gt to return to the Main Menu page Award BIOS Utility 63 EP830 All In One EPIC Board User s Manual 4 11 PC Health Status This section supports hardware monitering that lets you monitor those parameters for critical voltages temperatures and fan speed of the board Phoenix AwardBlOS CMOS Setup Utility PC Health Status ltem Help Menu Level gt rz Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults e SYSTEM Temperature Show you the current system temperature e CPU Temperature The current system CPU temperature will be automatically detected by the system Press lt Esc gt to return to the Main Menu page 64 Award BIOS Utility EP830 All In One EPIC Board User s Manual 4 12 Load Optimized Defaults This option allows you to load your system configuration with default values These default settings are optimized to enable high performance features Phoenix AwardBlOS CMOS Setup Utility
24. PCI Express x1 and AC 97 Codec Audio all in one single board Additionally it provides you with unique embedded features such as 4 serial COM ports RS 232 4 USB2 0 ports for high speed peripherals 2 IEEE 1394a ports and PCI Express expansion It can achieve the best stability and reliability that makes your system perform the most endurable operation in any critical environments The built in Watchdog Timer has enhanced the system reliability that achieves a unique feature to distinguish itself from other boards Designed for the professional embedded developers the Socket M 478 embedded board EP830 Series is virtually ultimate one step solution for embedded system applications Introduction 1 EP830 All In One EPIC Board User s Manual 1 1 Specifications e CPU Socket M 478 for Intel Yonach 8 Merom Core Duo and Core Solo processors e CPU Frequency FSB533 667MHz e System Chipset Intel 945GME and ICH 7M Phoenix Award BIOS Y2K compliant 4Mbit Flash DMI Plug and Play PXE Ethernet Boot ROM SmartView for multiple LCD type selection display mode option and application extension features RPL PXE Ethernet Boot ROM Load Optimized Default customized Setting in the BIOS flash chip to prevent from CMOS battery fail e System Memory One x 200 pin DDR2 SODIMM socket m Maximum to 2GB DDR2 memory e L2 Cache integrated in CPU e Onboard IDE m One PATA 100 with 44 pin 2 0 pitch box header Two SATA 150
25. Serial ATA Auto PATA IDE Mode Secondary Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support IDE DMA transfer access Automatic data transfer between system memory and IDE device with minimum CPU intervention This improves data throughput and frees CPU to perform other tasks On Chip Primary Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately The default value is Enabled D NOTE Choosing Disabled for these options will Award BIOS Utility gt EP830 All In One EPIC Board User s Manual automatically remove the IDE Primary Master Slave PIO and or IDE Secondary Master Slave PIO items on the menu IDE Primary Secondary Master Slave PIO The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes 0 to 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device IDE Primary Secondary Master Slave U
26. customary automation control The digital I O can be configured to control cash drawers sense warning signals from an Uninterrupted Power System UPS or perform store security control The digital I O is controlled via software programming Pin Description Pin Description Digital Output 0 Digital Output 4 CN11 ER Digital Output 1 EN Digital Input O o ES Digital Output 2 ER Digital Input 1 EN Digital Output 3 ER Digital Input 2 o fono ofw Oj vola Oje ala Du O Ojo ell O 2 4 11 LAN Connectors CN12 LAN1 LAN2 The board is equipped with a RJ 45 connector for Gigabit LAN To connect the board to a 1000 100 10 Base T hub just plug one end of the cable into LAN1 and connect the other end to a 1000 100 10 Base T hub CN12 and LAN2 share the same channel of signal however only one of them can be selected LAN2 is the default setting 24 Jumpers and Connectors EP830 All In One EPIC Board User s Manual Pin Description MDI3 any 6 won 8 mDio 9 INC Pin Description meal emo e mos B 7100 1000 LAN LED 87065437 Jumpers and Connectors 25 EP830 All In One EPIC Board User s Manual Pin Description LAN 7654321 6 mos B 100 1000LANLED 2 4 12 Keyboard and PS 2 Mouse Connector CN13 The board provides a keyboard and Mouse interface CN13 is a DIM connector for PS 2 keyboard Connection VIA Y Cable Pin Signal Mouse Data GND
27. d the system will boot and you can enter Setup freely e APIC Mode Use this item to enable or disable APIC Advanced Programmable Interrupt Controller mode that provides symmetric multi processing SMP for systems e MPS Version Control For OS This item specifies the version of the Multiprocessor Specification MPS Version 1 4 has extended configuration tables to improve support for multiple PCI bus configurations and provide future expandability e Small Logo lt EPA gt Show If enabled the EPA logo will appear during system booting up if disabled the EPA logo will not appear Press lt Esc gt to return to the Main Menu page Award BIOS Utility 49 EP830 All In One EPIC Board User s Manual 4 7 Advanced Chipset Features This section contains completely optimized chipset s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware Phoenix AwardBlOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable CAS Latency Time DRAM RAS to CASA Delay DRAM RAS Precharge Precharge delay lt tRAS gt System Memory Frequency System BIOS Cacheable Video BIOS Cacheable gt PCI Express Root Port Func On Chip Frame Buffer Size DVMT Mode DVMT FIXED Memory Size Boot Display Panel Scaling Panel Type ltem Help Menu Level gt By SPD Auto Auto Aut
28. dent on your application e Boot Display This item is for Intel define ADD card only Press lt Esc gt to return to the Main Menu page 52 Award BIOS Utility EP830 All In One EPIC Board User s Manual 4 8 Integrated Peripherals This section allows you to configure your SuperlO Device IDE Function and Onboard Device Phoenix AwardBlOS CMOS Setup Utility Integrated Peripherals gt OnChip IDE Device Press Enter item Help gt Onboard Device Press Enter Menu Level b gt Super IO Device Press Enter Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults Award BIOS Utility 53 EP830 All In One EPIC Board User s Manual e OnChip IDE Device Scroll to this item and press lt Enter gt to view the sub menu OnChip IDE Device 54 Phoenix AwardBlOS CMOS Setup Utility OnChip IDE Device IDE HDD Block Mode Enabled IDE DMA transfer access Enabled On Chip Primary PCI IDE Enabled IDE Primary Master PIO Auto IDE Primary Slave PIO Auto IDE Primary Master UMDA Auto IDE Primary Slave UMDA Auto On Chip Secondary PCIIDE Enabled IDE Secondary Master PIO Auto A IDE Secondary Slave PIO Auto sector the drive Can IDE Secondary Master UMDA Auto EH IDE Secondary Salve UMDA Auto ltem Help Menu Level gt p lf your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of On Chip
29. e Range m 1to 255 m Minute Second e Program Sample Watchdog Timer can be set to system reset after 5 second timeout 2E 87 ae Device 8 Set Minute or Second N 08 Min 00 Sec 70 Watchdog Timer EP830 All In One EPIC Board User s Manual Appendix B Digital I O Digital UO Software Programing e GPI program sample Select Device 8 Activate GPIO5 GPIO5 pins are programmed as input pins Read only from pin Display input read value Digital I O 71 EP830 All In One EPIC Board User s Manual e GPO program sample oan ooo M 1 ar TT oxo oo 02F F2 Activate GPIO5 02F00 GPIO5 pins are programmed as output O2FFF pc port output HI 72 Digital I O
30. ed Defaults Init Display First This item allows you to decide to active whether PCI Slot or AGP first The options available are PCI Slot AGP Reset Configuration Data Normally you leave this item Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup or if installing a new add on cause the system reconfiguration a serious conflict that the operating system can not boot Options Enabled Disabled Resources Controlled By The Award Plug and Play BIOS can automatically configure all boot and Plug and Play compatible devices If you select Auto all interrupt request IRQ DMA assignment and Used DMA fields disappear as the BIOS automatically assigns them The default value is Manual 62 Award BIOS Utility EP830 All In One EPIC Board User s Manual IRQ Resources When resources are controlled manually assign each system interrupt to one of the following types in accordance with the type of devices using the interrupt 1 Legacy ISA Devices compliant with the original PC AT bus specification requiring a specific interrupt such as IRQ4 for serial port 1 2 PCI ISA PnP Devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture The default value is PCI ISA PnP PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This item allows you to set whether MPEG ISA VESA VGA Cards can work with PC
31. enever BIOS detects a non fatal error the system will stop and you will be prompted The system booting will not stop for a keyboard All But Saige Keyboard error it will stop for other errors The system booting will not stop for a disk error it aes ill stop for oth Diskette will stop for other errors The system booting will not stop for a keyboard or A au disk it will stop for oth Disk Key isk error it will stop for other errors Press lt Esc gt to return to the Main Menu page 44 Award BIOS Utility EP830 All In One EPIC Board User s Manual 4 6 Advanced BIOS Features This section allows you to configure and improve your system to set up some system features according to your preference Phoenix AwardBlOS CMOS Setup Utility Advanced BIOS Features gt CPU Feature Hard Disk Boot Priority CPU L1 amp L2 Cache Hyper Threading Technology Quick Power On Shelf Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Onboard Lan Boot ROM Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Security Option APIC Mode MPS Version Control For OS Small Logo lt EPA gt Show item Help Press Enter Menu Level gt Press Enter Enabled Enabled Enabled Floppy Hard Disk CDROM Enabled Disabled On Fast Disabled Setup Enabled 1 4 Disabled Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previou
32. ever enter the SUSPEND mode It defines continuous idle time before the system Pe een entering the SUSPEND mode 0 30 40 If any item defined in J is enabled and active the Min 1 Hr SUSPEND timer will be reloaded HDD Power Down If HDD activity is not detected for a specified length of time in this field the hard disk drive will be powered down while other devices remain active 60 Award BIOS Utility Delay 4 Sec EP830 All In One EPIC Board User s Manual Soft Off by PWR BTTN This option only works with systems using an ATX power supply It also allows users to define which type of soft power OFF sequence the system will follow The default value is nstant Off This option follows the conventional manner of system performance when turning the power to OFF Instant Off is a software power OFF sequence requiring the power supply button is switched to OFF Upon the system s turning OFF through the power switch this option will delay the complete system power OFF sequence approximately 4 seconds Within this delay period the system will temporarily enter into the Suspend Mode enabling you to restart the system at once Power On by Ring This option allows the system to resume or wake up upon detecting any ring signals coming from an installed modem The default value is Enabled Resume by Alarm If enable this item the system can automatically resume after a fixed time in accordance with the
33. formation about your system Use arrow keys to highlight each item and use lt PgUp gt or lt PgDn gt key to select the value you want in each item Phoenix AwardBlOS CMOS Setup Utility Standard CMOS Features ltem Help Menu Level gt Change the day month year and century Date mm dd yy Sat Nov 6 1999 Time hh mm ss 11 21 35 IDE Channel 0 Master IDE Channel 0 Slave gt IDE Channel 1 Master IDE Channel 1 Slave None Video EGA VGA Halt On All Errors Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults Date The date format is lt day gt lt date gt lt month gt lt year gt Press lt F3 gt to show the calendar It is determined by the BIOS and read only from Sunday to Saturday It can be keyed with the numerical function key from 1 to 31 It is from January to December It shows the current year of BIOS Time This ttem shows current time of your system with the format lt hour gt lt minute gt lt second gt The time is calculated based on the 24 hour military time clock For example 1 p m is 13 00 00 42 Award BIOS Utility EP830 All In One EPIC Board User s Manual e IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave These items identify the types of each IDE channel installed in the computer There are 45 predefined types Type 1 to Type 45 and 2 user s definable
34. isk devices GND GND 5 sata Rx 6 SATARX or SATA1 SATA2 Jumpers and Connectors 33 EP830 All In One EPIC Board User s Manual MEMO 34 Jumpers and Connectors EP830 All In One EPIC Board User s Manual Chapter 3 Hardware Description 3 1 Microprocessors The EP830 Series supports Socket M 478 for Intel Yonah amp Merom Core Duo and Core Solo processors which make your system operated under Windows 2000 XP and Linux environments The system performance depends on the microprocessor Make sure all correct settings are arranged for your installed microprocessor to prevent the CPU from damages 3 2 BIOS The EP830 Series uses Award Plug and Play BIOS with a single 4Mbit Flash EPROM 3 3 System Memory The EP830 Series industrial CPU card supports one 200 pin DDR2 SODIMM sockets for a maximum memory of 2GB DDR2 SDRAMs The memory module can come in sizes of 64MB 128MB 256MB 512MB 1GB and 2GB Hardware Description 35 EP830 All In One EPIC Board User s Manual 3 4 1 0 Port Address Map The Intel Yonah amp Merom Core Duo and Core Solo CPUs can communicate via I O ports There are total 1KB port addresses available for assignment to other devices via I O expansion cards Address Devices 070 07F 080 09F 0A0 0BF 0CO ODF DMA controller 2 0F1 Reset math coprocessor MDA video card including LPT1 Serial port 1 COM1 Serial port 3 COM3 Serial port 42 COM2
35. nes the typematic rate of the keyboard The default value is Disabled Enabled Enable typematic rate and typematic delay programming Disable typematic rate and typematic delay Disabled programming The system BIOS will use default value of these 2 items controlled by keyboard e Typematic Rate Chars Sec This option refers to character numbers typed per second by the keyboard The default value is 6 6 6characterspersecond 8 8characterspersecond 10 10 characters per second 42 12characterspersecond 15 15characterspersecond 20 20 characters per second 24 24characterspersecond 30 30 characters per second e Typematic Delay Msec This option defines how many milliseconds must elapse before a held down key begins generating repeat characters The default value is 250 250 250msec 500 500msec 1000 1000 meer 48 Award BIOS Utility EP830 All In One EPIC Board User s Manual e Security Option This item allows you to limit access to the system and Setup or just to Setup The default value is Setup will not boot the access to Setup will be denied either Hall will boot but the access to Setup will be denied Y NOTE To disable the security select PASSWORD SETTING at Main Menu and then you will be asked to enter a password Do not type anything just press lt Enter gt and it will disable the security Once the security is disable
36. o Auto Auto Enabled Disabled Press Enter 8MB DVMT 128MB CRT Auto 640x480 18Bit Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values e DRAM Timing Selectable F7 Optimized Defaults Use this item to increase the timing of the memory This is related to the cooling of memory e CAS Latency Time You can select CAS latency time to HCLKs 2 3 or Auto The board designer should have set up these values in accordance with the installed DRAM Do not change these values unless you have to change the specifications of the installed DRAM or CPU e DRAM RAS to CAS Delay When DRAM is refreshed both rows and columns are addressed separately This field lets you insert a timing delay between the CAS and RAS strobe signals used when DRAM is written to read from or refreshed 50 Award BIOS Utility EP830 All In One EPIC Board User s Manual e DRAM RAS Precharge The precharge time is the number of cycles it takes for the RAS to accumulate its charge before DRAM refresh If insufficient time is allowed refresh may be incomplete and the DRAM may fail to retain data e Precharge Delay lt tRAS gt The precharge time is the number of cycles it takes for DRAM to accumulate its charge before refresh e System Memory Frequency This item helps you set main memory frequency When using an external graphics card it can be adjusted to enable the best perfo
37. rmance for your system e System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at FOOOOh FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result The default value is Disabled e Video BIOS Cacheable This item allows you to change the Video BIOS location from ROM to RAM Video Shadow will increase the video speed e PCI Express Root Port Func Scroll to this item and press lt Enter gt to view the sub menu to decide the PCI Express Port Phoenix AwardBlOS CMOS Setup Utility PCI Express Port Func ltem Help Menu Level gt PCI Express Port 1 Auto PCI Express Port 2 Auto PCI Express Port 3 Auto PCI Express Port 4 Auto PCI E Compliancy Mode v1 0a rz Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults Award BIOS Utility 51 EP830 All In One EPIC Board User s Manual Press lt Esc gt to return to the Advanced Chipset Featurs page and press it again return to the Main Menu page VGA Setting e On Chip Frame Buffer Size Use this item to set the VGA frame buffer size e DVMT Mode DVMT Dynamic Video Memory Technology helps you select the video mode e DVMT Fixed Memory Size DVMT Dynamic Video Memory Technology allows you to select a maximum size of dynamic amount usage of the video memory The system would configure the video memory depen
38. s Values Award BIOS Utility F7 Optimized Defaults 45 EP830 All In One EPIC Board User s Manual e CPU Feature Scroll to this item and press lt Enter gt to view the CPU Feature sub menu Phoenix AwardBlOS CMOS Setup Utility CPU Features ltem Help Menu Level gt gt Delay Prior to Thermal 16 Min C1E Function Auto Execute Disable Bit Enabled Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults e Hard Disk Boot Priority Scroll to this item and press lt Enter gt to view the sub menu to decide the disk boot priority Phoenix AwardBlOS CMOS Setup Utility Hard Disk Boot Priority ltem Help Menu Level gt Pri Master Pri Slave Sec Master i Use lt gt or lt gt to select Sec Slave USBHDDO a gece Mon press lt gt USBHDD1 to move it up or to USBHDD 2 move it down the list Press lt ESC gt to exit this Bootable Add in Cards Move PU PD Change Priority F10 Save ESC Exit F5 Previous Values F7 Optimized Defaults 46 Award BIOS Utility EP830 All In One EPIC Board User s Manual Press lt Esc gt to return to the Advanced BIOS Features page e CPU L1 amp L2 Cache These two options speed up memory access However it depends on the CPU chipset design The default setting is Enabled CPUs without built in internal cache will not provide the CPU Internal Cache item on
39. s it again to the Main Menu Award BIOS Utility 57 EP830 All In One EPIC Board User s Manual 4 9 Power Management Setup The Power Management Setup allows you to save energy of your system effectively It will shut down the hard disk and turn OFF video display after a period of inactivity Phoenix AwardBlOS CMOS Setup Utility Power Management Setup ACPI Function ACPI Suspend Type Power Management Video Off Method Video Off In Suspend Suspend Type MODEM Use IRQ Soft Off by PWR BTTN Power On by Ring Resume by Alarm Primary IDE 0 Primary IDE 1 Secondary IDE 0 secondary IDE 1 FDD COM LPT Port PCI PIRQ A D ltem Help Menu Level gt Enabled S1 POS Min Saving DPMS Yes Stop Grant 3 Instant Off Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled 1 7 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F7 Optimized Defaults F5 Previous Values e ACPI Function This item allows you to enable disable the Advanced Configuration and Power Management ACPI The function is always Enabled e ACPI Suspend Type This item specifies the power saving modes for ACPI function If your operating system supports ACPI such as Windows 98SE Windows ME and Windows 2000 you can choose to enter the Standby mode in S1 POS or S3 STR fashion through the setting of this field Options are 58 Award BIOS Utilit
40. t Analog Green GND ES 28 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 4 16 CPU amp System Fan Connectors FAN1 FAN2 Fan1 is a fan connector for CPU and FAN2 for system Pentium microprocessors require a fan for heat dispensing The CPU System fan connectors respectively provide power to the CPU System fans d 3 Sensor i 1 3 1 2 4 17 CompactFlash Socket CFS1 The board is equipped with a CompactFlash disk type II socket on the solder side to support an IDE interface CompactFlash disk card with DMA mode supported The socket is especially designed to avoid incorrect installation of the CompactFlash disk card When installing or removing the CompactFlash disk card please make sure the system power is off The CompactFlash disk card is defaulted as the C or D disk drive in your PC system Pin Description Pin Desorption Ce baar o baas lagen 33 vs e arase 94 10RD r4 Address Jumpers and Connectors 29 EP830 All In One EPIC Board User s Manual rin Desenipion Pin Description CFS1 123 45 6 7 8 9 1011 12 13 1415 16 17 18 19 20 21 22 23 24 25 0000000000000000000000000 0000000000000000000000000 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 2 4 18 Parallel IDE Connector IDE1 There is one built in IDE channel 1 parallel ATA 100 to support up to three IDE devices IDE
41. t and F 2 1 O0000000 do 00000000 20 00000000 perta LN s Re AA SEIN E eld po HIE ot ELLELTELTELETETTETEEEEE E E EEE k cieaedeacesrensweneneaditnty Ad EPR AAA III LEAR ED AUGE 9000 OLES TI MIT LEEETT bree ag KKK bee a ELETI IDET COLLETT MIT LELETET LLE LELE EE TITEL AUGE TETEL LELET 145845 LELE EE Epiit de e EE TITEL TTT H sgsase paco re AAA AA Saar PSPSPS PEPPERS PSPS di AAA TTT ITs Ct Tee ie LENE SE EE E PEERS ESE EE EEE AAA EPA eg BENS 00000 0000 1 EWOD NOS Component Side Jumpers and Connectors EP830 All In One EPIC Board User s Manual o 0000 OC wa O OC wa 0000000000000000000000 o oo 0000000000000000000000 Oo o oo oo 00 oooop U00O o e poo 00 00000 0900 29 00 00 O o 00 o O06 z 000 o 8 O ot jo 9 o Jo o 0 H o O o OO o OO e 38 H o OO O o O O 00 o9 O o2 ad o9 O O Joo O E Or hi o O Oo E 095 09 O 000 O 000 O 00 0 a o ot je 000 S e 000 U 000 000 se 000 aS 000 000 O 000 O O O R O He O o O o9 o 0000000000 on000000000 0000000000 1000000000 0000000000 o Solder Side 6 Jumpers and Connectors EP830 All In One EPIC Board User s Manual 2 2 Board Dimensions 20 85 41 32 121 16 139 60 134 84 29 52 65 94 58 29 42 45 10000700000 19 12 00000100000 EE 0 00
42. tem is powered ON External Speaker and Internal Buzzer Connector Pin 2 4 6 and 8 can be connected to the case mounted speaker unit or internal buzzer While connecting the CPU card to an internal buzzer please short pins 2 4 while connecting to an external speaker you need to set pins 2 4 to Open and connect the speaker cable to pin 8 and pin 2 ATX Power On Off Button This 2 pin connector named as Pin 9 and 10 connect the front panel s ATX power button to the CPU card which allows users to control ATX power supply to be power on off System Reset Switch Pin 11 and 12 can be connected to the case mounted reset switch that reboots your computer instead of turning OFF the power switch lt is a better way to reboot your system for a longer life of the system s power supply HDD Activity LED This connection is linked to hard drive activity LED on the control panel LED flashes when HDD is being accessed Pin 13 and 14 connect the hard disk drive to the front panel HDD LED Pin 13 assigned as and Pin 14 as Jumpers and Connectors 23 EP830 All In One EPIC Board User s Manual 2 4 9 Audio Connector CN9 CNY is a 10 pin connector to support the audio interface Pin Description Pin Description nui Hijo 5 lineinR 6 GND 7 AudioQutL 8 GND 2 4 10 Digital UO Port DIO Connector CN11 The board is equipped an 8 channel digital I O connector CN11 that meets requirements for a system
43. umpers JP4 JD 11 2 3 5 CMOS Clear Jumper IPS aio 11 2 3 6 CompactFlash Voltage Selection Jumper JP 11 2 3 7 COM1 Mode Selection Jumpers JP8 JP 11 JP14 12 2 3 8 COM1 4 Mode Selection Jumpers JP9 JP10 JP12 JP13 13 2 3 9 Audio Line Out Speaker Out Jumper JD 17 2 4 CONE ele 18 2 4 1 Power Control Connector CN 19 2 4 2 EPIC EXPRESS SIG ON anit See Se 19 2 4 3 Power Output Connector CND 20 2 4 4 LVDS Backlight Connector CNA 21 2 4 5 JST Connector for LVDS Flat Panel CND oooooocococcccccnoncnccncnnnnnnnnos 21 2 4 6 SMBUS Connector CNG dahanan a 22 2 4 7 IEEE 1394 Connectors CN7 CN10 cocccccccncncccncnnnnnnnnncnnnnnnnnnnnnnnnnnnos 22 2 4 8 Flat Panel Bezel Connector CNS 23 2 4 9 AECI COMEN 24 2 4 10 Digital I O Port DIO Connector ONT 24 2 4 11 LAN Connectors CN12 LAN1 LAN 24 2 4 12 Keyboard and PS 2 Mouse Connector CN13 W ssssesererererererereee 26 2 4 13 12V IN Power Connector ATI 27 2 4 14 Serial Port Interface Connectors COM1 COM2 COM3 COM4 27 2 4 15 Digital Visual Interface DVI Connector DNI 28 2 4 16 CPU System Fan Connectors FAN1 FAN2 ccccccsseeeeeees 29 2 4 17 CompactFlash Socket CES 29 2 4 18 Parallel IDE Connector D I 30 2 4 19 USB Port Connector USB eai asana an a aSa 32 2 4 20 USB Connector USB2 ccccccccccccccscessseseeeeeeceeececcenccenseseeeeeees 32 2 4 21 SATA Connectors SATA1 GATIAZ
44. y EP830 All In One EPIC Board User s Manual S1 POS The S1 sleep mode is a low power state In this state no system context is lost CPU or chipset and hardware maintains all system contexts S3 STR The S3 sleep mode is a lower power state where the information of system configuration and open applications files is saved to main memory that remains powered while most other hardware components turn off to save energy The information stored in memory will be used to restore the system when a wake up event occurs e Power Management This option allows you to select the type or degree of power saving for Doze Standby and Suspend modes The table below describes each power management mode It is maximum power savings only available for SL CPUs The inactivity period is 1 minute in each mode 5 It sets each mode Select time out periods in the PM User Define Timers section It is minimum power savings The inactivity period is 1 hour in each mode except the hard drive Disabled Default value e Video Off Method This setting determines the manner in which the monitor is blanked V H It turns OFF vertical and horizontal synchronization ports SYNC Blank jand writes blanks to the video buffer Select this option if your monitor supports the Display Power Management Signaling DPMS standard of the Video Electronics Standards Association VESA Use the supplied software for your video subsystem to select video

EP830 User`s Manual VA1

Contents

Download Pdf Manuals

Related Search

Related Contents