Configuration Tool Installation/Operation Manual
Contents
1. MURPHY 4 Ses FW Murphy CD101 Autostart PC Configuration Tool File Attach To Cascade Configurations Help i h ee Parameter 13 26 Parameter 28 36 Parameter 37 48 Parameter 48 59 Reserved Firmware Yersion Unknown Configuration Value Default Configuration Yalue Binary Copyright FW Murphy Inc 2006 1 Engine Speed Source OoOooos8 OOOOO This is a PC based configuration tool used to create configurations for the 2 Crank Altempts OoOo00sao0 00000 rainy rae Engine Controller 3 Crank Timer popo00ss OOOOO Firmware Revision 2 1 28 or higher popo0omp0 20000 This Process can be Started by oe OoOosos 00000 Selecting an Engine Speed Source and the form will prefill with CASCADE Ooosso ooooo factory defaults Or PaE RUNG C Ooosss o0000 Use the File Open and select a file ECU STATUS r set the form REMOTE START CRANK REST oomooo 00000 Write or Read the Form s configuration LOW OIL PRESSURE oo soo O00000 to 7 from a unit by using oO HIGH ENGINE TEMPERATURE opg BO ooo000 ee To Cascade Connect to OVER SPEED The Configurations Menu item will Oosoee O00000 then be available UNDER SPEED OOsgsooO oooo0 OVER CRANK START FAIL CHARGE FAIL Red is not the default Value AUXILIARY1 e MURPHY Configuration Tool AUXILIARY2 Cascade Version 1 0 10 Installation and Operations Manual 00 02 0724 01 25 11 Section 40 In order to con2. Once the program is loaded successfully flip the number 1 dip switch to the open position and remove power from the controller Section 40 00 02 0724 01 25 11 6 Application GUI Overview This section provides instructions for launching the Cascade Configuration Tool identifies the application features that are accessible through the menu bar and defines general navigation Launching the Application To launch the application you either double click the Cascade Configuration Tool application icon ae located on your desktop or select Cascade Configuration Tool Design from the list of programs under your Start menu The following dialog box is displayed FW Murphy CD101 Autostart PC Configuration Tool File Attach To Cascade eld 3 5 O Parameter 1 12 Parameter 13 26 Parameter 28 36 Parameter 37 48 Parameter 48 59 Reserved Firmware Version Unknown Configuration Configuration Yalue Binary Copyright Fw Murphy Inc 2006 Value Default popo000s OOOOO This is a PC based configuration tool 1 Engine Speed Source used to create configurations for the 2 Crank Attempts 3 Crank Timer 4 Crank Rest Timer 5 Start Delay Timer 6 Stop Delay Timer Preheat Timer 8 Extended Preheat Timer 9 Warmup Timer 10 Cooldown Timer 11 Bypass Timer 12 Energize to Stop Timer OOOO8O OOOOS8s OOOS8oOoO OOOS8Os8 OOOsso OOOsss OOgoOoo0 OOSOO8 OOgoOs8D OOsOe8 OOgssoo
3. OO0000 OOo0o00 OOoOooO OOoooO OOOoOO OOOOO OOo0o00 o0o000 00000 mi oo000 Cascade Autostart Engine Controller Model CD101 Firmware Revision 2 1 28 or higher This Process can be Started by Selecting an Engine Speed Source and the form will prefill with factory defaults i Use the File Open and select a file to set the form j write or Read the Form s configuration to from a unit by using Attach To Cascade Connect to Device The Configurations Menu item will then be available Not Used for Selected Speed Source Red is not the default Value CO Communicating with Cascade Menus and Tool Bars FW Murphy CD101 Autostart PC Contig Fie Attach To Cascade i ds a e Help The tool bar provides one click access to opening an existing file and saving the currently displayed file These same functions are available from the File drop down menu The File menu also provides the ability to print a report Note The Report selection will only print a report of the current configuration to a printer connected to the PC and will not display the report Section 40 00 02 0724 01 25 11 Attach To Cascade Open Configuration File Save Current Configuration to a File Frink Report Exit Selecting Attach to Cascade provides the ability to connect to an existing Cascade once all cabling is connected and power is initiated on the controller
4. Once connected the configuration from the Cascade can be downloaded and viewed FW Murphy CD101 Autostart PC Contig Attach To Cascade Help Connect Parameter 1 12 Parameter 13 26 Parameter 28 Selecting Configurations allows you to write to a device read from a device restore the initial configuration or set to the factory defaults The Configurations menu item is grayed out and unavailable when not directly connected to a device NOTE The PC and device must be linked in order to have access to the Configurations menu item PW Murphy CD101 Autostart PC Contig File Attach To Cascade 99 ooo Help d ec Selecting Help provides access to the Instruction and Operations manual information about the PC Configuration Tool and the User s Manual Configurator IOM Cascade IOM About PE Configurator Section 40 00 02 0724 01 25 11 8 Navigating Cascade Configuration Tool Navigating the Cascade Configuration Tool application interface is versatile and easy It contains one window and it has four sections of information for each tab Each tab contains a similar format although not identical See the illustration below A B C D E DER FW Murphy CD101 Autost rt PC Configuration Tool Parameter 1 12 Parameter 13 26 Firmware Version Unknown Configuration Value Default Configuration Yalue Binary Copyright FW Murphy Inc 2006 Configuratio alue Defaul
5. This will return you to the previous screen Click Next to continue Section 40 00 02 0724 01 25 11 oe i Cascade PC Configuration Tool Setup Disk Space The list below includes the drives you can install Cascade PC Configuration Tool Setup to along with each drive s available and required disk space 4 The Wizard will now install the program This may take several minutes The following screen is displayed during the installation Disk Size OFB 34GB 816GB 216GB 816GB 13666 ig Cascade PC Configuration Tool Setup Available OKB 14GB 90GB 90GB 90GB 20GB Installing Cascade PC Configuration Tool Setup Cascade PC Configuration Tool Setup is being installed Please wait ig Cascade PC Configuration Tool Setup Installation Complete Cascade PC Configuration Tool Setup has been successfully installed Click Close to exit Please use Windows Update to check for any critical updates to the NET Framework Section 40 01 25 11 00 02 0724 Installing USB Driver Tools Needed USB to RS485 Converter USB Cable Programming Cable 0 E g os m T ian r g Installation To use the USB connection device to download the configuration into the Cascade controller you will need to use the Murphy installation kit Follow the instructions listed below to connect the computer and device Section 40 00 02 0724 01 25 11 4 NOTE The installation kit provides
6. E ER E R R OO gsooO O00000 36 1s Digit soosoo 00000 iirc ieee Deni ick is cates aie Not Required for Selected Speed Source Red is not the default Value Communicating with Cascade Here is what each section contains A The configuration section a list of items that can be configured B The Value Default section contains drop down boxes from which the user can select a value C The Configuration Value Binary section contains the binary value for what is selected in section B NOTE This section will indicate to the user when the default value has been altered by turning the binary values to the right red D The Help section provides context sensitive help for each of the values to be entered l NOTE The Help is displayed when the box is selected E This section is displayed on screens requiring additional user input NOTE Sections B and E are the only sections to which the user can make changes Section 40 00 02 0724 01 25 11 9 Guidelines for Configuring the Cascade Configuration Tool This section provides guidelines for setting up common configuration items in Cascade Configuration Tool There is a logical sequence to follow when configuring the Cascade These sequences will be explained in four separate topics They are e Defining the System e System of Operation e System of Interface Defining the System The first step in defining the system is to gather informatio
7. 1 Parameter Values and Corresponding LED Indication LEDs shown here form a binary code indicating the configuration value Shown from Top to bottom the LEDs read from Left to Right see Fig 1 A filled dot means LED is ON LED Bank1 Value default LED Bank 2 LED Bank1 Value default LED Bank 2 Parameter Description 1 Engine Speed Source OOOOO Magnetic Pickup OOOO0O 13 Aux Input Bypass OOO0O Generator AC OOOO Timer OQOO0O0 J1939 ECU O00000 O00090 2 Crank Attempts OOOO O 3 OOO0 5 O00000 10 O08 0 Continuous O00900 3 Crank Timer OOO00C OO00 O 000 O00090 O00000 O00 O 00 O00 O00 4 Crank Rest Timer O00000 O00000 0000 0008 0080 O008 00 00 14 Cranking Motor Disabled OOO0O0 Abutment Protection Delay 1 00 s O00000 5 Start Delay Timer OOO0O000 Current crank attempt is 1 255 O00000 auto mode only aborted if an RPM greater 1 505 OO0C than 10 is not detected 1 555 O0 00 after this delay from start 2 00 s O08 0 of crank has expired 2 255 OO00O 2 50S OO00 6 Stop Delay Timer O00000 MPU and J1939 speed 2 155 O 0O00 auto mode only source only 3 00 s O00000 3 25S O00000 3 50 S O00 3 755 O 00 4 00s O00 7 Preheat Timer 4 25 S O00 4 505 O00000 4 75S 0000 5 00 s 0008e 15 Remote Start Signal eee ee QO000 Type Momentar OOO00 Lo Oil Press Open Fault QOQOOO Lo Oil Press Close Fault QOOO Hi Eng Temp Open Fault OOOOO 8 Extended
8. Configuration Value Binary c3 opyright Fw Murphy Inc 2006 1 Engine Speed Source goo0oo 8 00000 This ame pas edc ae ation tool 28 Initial Power Up Mod Omegeco ooooo This is a PC based c oniga ation tool i ooooo ne edto onfigurations for the f j a to create configurations for the ce mies EER Cascade eat Enare e Cont 0i i a Omeeos oooco Cacao tat Eafe e ark 3 Crank Timer o000ss O00000 Fi R 2 1 28 or higher na PEEPI BCEE EEEEE Fi R 2 1 28 or higher Ooosoo 00000 is Proc n be Started by is Proc n be Started by lt x 4 Crank Rest Timer p popoompos 00000 Selecting an Engine Speed Source d Source 5 Start Delay Timer tie rom ipren with sr ie sion orm a ii H wil th defaults 6 Stop Delay Timer ooo eo O0000 10 Diai Omeeee ooooo on Or File and select a fil ok 7 Preheat Timer OOOsss O00000 AR ere apen ie 1s Digi BoOooo0o0 ooooOo a me or and select a file 8 Extended Preheat Timer Enter Crank Disconnec fn lis L L to Oogsooo 00000 i or nte or ae e roms eh re 9 Warmup Timer OOgoo 00000 eft ite oroa 33 1000s Digit soo0o0o8 oomoo 00000 i to Hae l aeee Atta chTo Cascade Con igi soooso The Co figuration Meru tem wil cept A gooo0o00 The Co figurations Menu item wil ble eat aes then be avaiable 35 10s Digit mooome ooooo then be availa 10 Cooldown Timer 11 Bypass Timer 12 Energize to Stop Timer X ERI E E E
9. Crank Disconnect Freq Generator AC speed source only 1 s digit 33 Crank Disconnect RPM ECU or MPU speed source only 1000 s digit 34 Crank Disconnect RPM ECU or MPU speed source only 14 Lo Oil Press Shutdown Hi Eng Temp Shutdown Overspeed Shutdown Overcrank Shutdown Alternator Fail Battery High Low Weak Engine Speed Up Engine Speed Down Common Alarm Controller in AUTO mode Shutdown Loss of Speed Signal Fault Underspeed Fault Not Used 0s 0 25 5 0 50 s 0 755 1 00 S 1 25S 1 50 S 1 755 2 005 2 295 2 50 S 2 155 3 00 s 3 25S 3 50 s 3 155 400s 4 255 4 505 4 155 eee OO000 O 0O00 O O0 8 O00000 O00000 O00000 O00 O00 O09000 0000 0008 0080 Power Up in Manual OOOOO Power Up in Automatic OOOO OOOOO OOO00 OO08O OO0C O08 00 O00000 O00900 OO000 O O000 O O00 8 O00000 O00 O 0D0 O00 O09000 O09000 0000 0O00 00000 0O00 0000 0O00 5 005 50 Hz OOOO0O Hz O00000 OOOQOOQOQO O00000 OO08O OO0C O00900 O080 O09000 OOOO0O OOO0O0 OO008O OO0C 8 O08 00 OO080 O08 O OO000 O 000 O 00 8 OOOOO O00000 O00000 OOO0 O09000 O00000 O08 O OO000 O 000 1 1010 OOOO0O OQOQO0O08 O00000 00 02 0724 Table 1 Parameter Values and Corresponding LED Indication continued LEDs shown here form a binary code indicating the configuration value Shown from Top to bottom the LEDs read from Left to Right se
10. Preheat O0 000 Hi Eng Temp Close Fault OOOO0 during Crank only used i 18 Digital Input 3 O O00 O Not Used OOO00O0 preheat timer is also set Auxiliary Input 1 Winter Summer OOOO to a non zero value Momentary Stop O00000 Immediate Warning OOO0 must be less than or Delayed Warning OO 000O equal to crank timer Immediate Shutdown OO000 Delayed Shutdown O0 O Delayed Aux Input Shtdwn OO 9 Warmup Timer O00000 Run Idle Line Fill O 000 Auxiliary Crank Disconnect O OO O00000 19 Digital Input 4 Not Used QOO00O0 10 Cooldown Timer O00000 Auxiliary Input 2 Winter Summer O00009 Momentary Stop O00000 Immediate Warning OOO0 Delayed Warning O00900 11 Bypass Timer Immediate Shutdown O00000 Delayed Shutdown OO00O Delayed Aux Input Shtdwn OO Run Idle Line Fill O O0O0 Auxiliary Crank Disconnect O OO O 0e8 0 22 Fuel Relay Control Energized to Run OOO00O0 12 Energize to Stop OO0 OO 15 Sec OOOO0O0 non ECU Engines Note Energized to Stop OO00e Timer 30 Sec OO00 On ECU engines fuel relay is used for ECU power Section 40 00 02 0724 01 25 11 13 Table 1 Parameter Values and Corresponding LED Indication continued LEDs shown here form a binary code indicating the configuration value Shown from Top to bottom the LEDs read from Left to Right see Fig 1 A filled dot means LED is ON Parameter Description 23 Auxiliary Output 1 24 Auxiliary Output 2 25 Auxiliary Output 3 26 Auxili
11. amming mode Click on Configurations then click Read from Device After uploading the configuration the parameters will be shown in the configuration value row To distinguish if the parameter not a default parameter the small configuration value boxes will be red Restore Initial Configuration This feature allows the user to restore the Cascade s configuration to the configuration software from when the initial Read from Device was selected This allows the user to make changes to a configuration originally pulled from the Cascade then go back to view compare or load the original configuration before changes were made Set to Factory Defaults This feature enables the user to reset the factory defaults of the Cascade without having to manually do so Help Configurator IOM Click this menu item to obtain an Installation and Operations Manual for the Cascade Configuration Tool Cascade IOM Click this menu item to access the Installation and Operations Manual for the Cascade This will open a window browser and redirect the user to the Cascade product home page on the FW Murphy web site Under the Literature Tab of this page the current IOM is listed and provided in a PDF format This feature is only available on a PC that is connected to the internet About PC Configurator Tool This identifies the software version of the configuration tool Section 40 00 02 0724 01 25 11 zie Appendix A Tables Table
12. ary Output 4 Section 40 01 25 11 Parameter LED Bank1 Value default LED Bank 2 LED Bank1 Value default LED Bank 2 O D00 Not Used Warmup Cooldown Warmup Cooldown Preheat Engine Running At Load Lo Oil Press Shutdown Hi Eng Temp Shutdown Overspeed Shutdown Overcrank Shutdown Alternator Fail Battery High Low Weak Engine Speed Up Engine Speed Down Common Alarm Controller in AUTO mode Shutdown Loss of Speed Signal Fault Underspeed Fault Not Used Warmup Cooldown Warmup Cooldown Preheat Engine Running At Load Lo Oil Press Shutdown Hi Eng Temp Shutdown Overspeed Shutdown Overcrank Shutdown Alternator Fail Battery High Low Weak Engine Speed Up Engine Speed Down Common Alarm Controller in AUTO mode Shutdown Loss of Speed Signal Fault Underspeed Fault Not Used Warmup Cooldown Warmup Cooldown Preheat Engine Running At Load Lo Oil Press Shutdown Hi Eng Temp Shutdown Overspeed Shutdown Overcrank Shutdown Alternator Fail Battery High Low Weak Engine Speed Up Engine Speed Down Common Alarm Controller in AUTO mode Shutdown Loss of Speed Signal Fault Underspeed Fault Not Used Warmup Cooldown Warmup Cooldown Preheat Engine Running At Load 28 Initial Power Up Mode 29 Oil Pressure Crank Disconnect Delay non ECU engines only 30 Nominal Generator Frequency genset only 31 Crank set Freq Generator AC speed source only 10 s digit 32
13. e Fig 1 A filled dot means LED is ON Description 01 25 11 Parameter Parameter 15 100 s digit 235 deg F 4 240 deg F 5 245 deg F 6 250 deg F 1 42 Lo Batt Voltage Warning Disabled 8 Setpoint 8 5V 3 9 0V 35 Crank Disconnect 0 95V MPU speed source 2 10 5V only 10 s digit 3 11 0V r 11 5V 9 18 0 6 19 0V 20 0V 9 21 0V 36 Crank Disconnect 008 00 0 ay 22 5V RPM ECU or MPU 1 23 0V speed source only 2 23 By sci i 43 Hi Batt Voltage Warning Disabled 5 Setpoint 12 5V 6 13 0V 7 13 5V 3 14 0V 9 14 5V 37 Overspeed Setpoint 15 0V above run speed 25 0V 25 5V 26 0V 26 5V 27 0V 28 0V 29 0V 38 Underspeed 30 0V Setpoint below 31 0V run speed 44 Weak Battery Warning disabled Voltage Setpoint 6 0 V 6 5 V 7 0V 7 5V 8 0 V 8 5 V 9 0 V 39 Underspeed 95V Response Speer Warning 12 0 V Shutdown 13 0V 40 Lo Oil Press 0 000 Disabled no shutdown 14 0 V Shutdown Setpoint 0 PSI 15 0 V ECU eng only 5 PSI 16 0 V 10 PSI 17 0V 15 PSI 18 0 V 20 PSI 19 0 V 25 PSI 90 0 deal 48 Flywheel Tooth OOOO 0 35 PSI Count MPU speed T 40 PSI source only 2 SPSI 100 s digit 3 m Flywheel Tooth 0 a ie Count MPU speed 1 41 Hi Eng Temp Disabled no shutdown i iat Shutdown Setpoint 190 deg F 4 ECU engines only 195 deg F 5 200 deg F 6 205 deg F r 210 deg F g 215 deg F 9 220 deg F 225 deg F 230 deg F Section 40 LED Bank1 Value default LED Bank 2 LED Bank1 Value default LED Ban
14. eeeeees 10 LJSTINING TNS SV SCI retiree rete eeetvekd vaxiueki vad goed ust EEE E OR 10 SVEM OF OC DSTAUOM erinin TE T E T oer igode hanwedetce edu Goewe 11 APPEDNAK P VOUS sess iad vatirseecics uc a a ave Rees 13 Introduction Cascade Configuration Tool is a PC based configuration software for the Cascade controller The easy to use interface enables you to modify the parameters of the Cascade as shown in Table 1 File transfer utilities for configuration and firmware upgrades are provided so that once the configuration is set it may be downloaded from your PC to the Cascade via a serial or USB connection Installation System Requirements A RS485 232 to USB adapter is required for transferring the configuration from the Configuration Tool to the Cascade While the Configuration software will function on any PC or laptop running Windows it will not perform transfers using the USB driver unless the operating system supports USB USB supported operating systems include Win98SE NT XP Vista and Windows Serial transfers using standard communication ports COM1 COM2 should be possible on all Windows platforms The Cascade Configuration Tool software and USB driver provide efficient use of your hard drive using only 3 5 MB of disk space after installation Section 40 00 02 0724 01 25 11 dice Installation Instructions Follow the steps below to install the Cascade Configuration Tool software on a PC or laptop 1 Inse
15. everything needed to connect the Cascade to your PC 1 Connect the programming cable end with the db9 connect to the RS485 to USB converter 2 Connect the USB cable to the USB to RS485 converter 3 Connect the opposite end of the programming cable to the Cascade 10 position connector PWMURPHY us MODEL ave Ma cascaoe CIM YISTES SIN Piti o NPUTHASNOG mA MAK 4 Connect the opposite end of the USB cable to the PC 5 Connect Battery to position 1 on the 15 position terminal block Section 40 00 02 0724 01 25 11 5 6 Connect Battery to position 2 on the16 position terminal block FWMURPHY Mu MOL CASCADE C0101 LISTED S H CE Ppa INPUT AASV ima MAX Programming Mode Flip dip switch number 1 to the closed position up on the rear of the Cascade This will allow the controller to power up in the programming mode Once all programming cables and power are connected to the Cascade initiate power The controller should now be in programming mode The Cascade s green LED to the right of AUTO will flash very quickly This LED turns off briefly while the right hand bank of LEDs flash on for proper bulb verification Once the bank of LEDs flash and remain off the green light to the right of AUTO will have a slower steady flash In the first bank of LEDs labeled OVER SPEED the bottom red LED remains on This is the first parameter and indicates you are now in Programming Mode
16. ill be entering File Open Configuration Item This feature allows the user to open a saved configuration from a location on the PC Save Current Configuration to a File This feature allows the user to save a configuration into a file on the PC This will allow the use of configuration at a later date Print Report This feature prints a report of all the parameters in the configuration using the default printer of the PC Exit This closes the configuration tool Attach to Cascade Connect This allows the configuration tool to communicate to the Cascade once all the cabling is connected and power is initiated on the controller Configurations Write to Device To download a configuration to the Cascade controller first make sure the PC is connected to the controller via USB to RS45 converter and the controller is in programming mode In the Configurations menu click Write to Device You will now see a text box with a message that states Successful Write to Device After downloading the configuration remove the USB to RS485 converter cable from the Cascade take the controller out of programming mode and cycle the power The controller will now power up with the new configuration installed Section 40 00 02 0724 01 25 11 sida Read from Device To upload a configuration from the Cascade controller first make sure the PC is connected to the controller via USB to RS45 converter and the controller is in progr
17. k 2 3 O00000 O00 O 0D0 O00 OQOOO0O0 OO00e OO0O08O OO0C O00000 O00000 O09000 OO000 O 000 O00000 O00000 O00000 O 0D0 O00 O09000 O00000 OOOQOQOQO O00000 O00000 OOO0 O00900 OO00 O09000 OO000 O 000 O00000 O00000 O00 O 0D0 O00 O09000 O00000 0000 0008 OOOO0O0 OOOO O00000 OOO0 O00900 O00000 O09000 OO000 O O000 O00000 O00000 O00 O 0D0 O00 O09000 O00000 0000 0008 QOOO0O OOO00 OO0O08O OO0C QOOO0O0 OOOO O00000 OO0O0 O00900 OO00 OO00O OO000 O O000 O00000 00 02 0724 Parameter Description LED Bank 1 Value default LED Bank 2 LED Bank 1 Value default LED Bank 2 O00000 OOOQOQO OOOO O00090 59 Fault Code SPN Conversion Method ECU Eng only Note if the ECU is using version 4 any of these options will NOTE Not all configuration parameters are used Some are skipped because they are reserved for future expansion Version 1 amp 4 Version 2 amp 4 Version 3 amp 4 50 Flywheel Tooth 0 53 Run Speed 0 OOO0O0 Count MPU speed 1 ECU or MPU 1 OQ000e source only 2 speed source only 2 O00000 1 s digit 3 10 s digit 3 O00000 4 4 OO OO 5 5 OO000 6 6 O00900 7 7 OO000 8 8 O O0O0 9 9 O00000 51 Run Speed 0 54 Run Speed 0 OOOOO ECU or MPU 1 ECU or MPU 1 O00000 speed source only 2 speed source only 2 O00090 1000 s digit 3 1 s digit 3 O00090 4 4 OO OO 52 Run Speed 0 5 OO000 ECU or MPU 1 6 O00000 speed
18. lamp terminal voltage is above threshold or charge fail input is inactive No speed data ECU or loss of speed non ECU Start Condition Failure RPM not below 10 Start Condition Failure ECU related or crank disconnect input is on before CAN Hw Bus Error preventing start attempting crank Battery Voltage is below low voltage warn Battery Voltage is above high voltage ing setpoint warning setpoint Alternator warning lamp terminal volt age is below threshold or charge fail input is active ECU Shutdown Red Stop or Protect ili fears eee er OR ECU Warning malfunction or Amber Auxiliary 1 Auxiliary input 1 is inactive Auxiliary input 1 is active Amd g1 oon Auxiliary 2 Auxiliary input 2 is inactive Auxiliary input 2 is active Weak Battery E Table 3 Error Codes LED States LED s ENGINE RUNNING Ecustatus REMOTE START CRANK REST LOW OIL PRESSURE 128 MSB HIGH ENGINE TEMPERATURE 64 OVERSPEED 32 UNDERSPEED OVERCRANK START FAIL AUXILIARY1 Obtain the error code parameter by adding all lit LED S See Table 1 for the corresponding parameter O CHARGE FAIL 4 O O AUXILIARY2 Section 40 00 02 0724 01 25 11 16 in order to consistently bring you the highest quality full featured products we reserve the right to change our specifications and designs at any time MURPHY products and the Murphy logo are registered and or common law trademarks of Murphy Industries LLC This documen
19. n for setting up your analog and or digital devices and control outputs For your convenience you may want to make a checklist of this information for entering into the Cascade Configuration Tool Once this information has been entered it will be available for subsequent configuration options The following items from the Main Menu List allow you to define the system Refer to the context sensitive help contained in the product for information on field options you will be entering Parameters Below is a list of the parameters that the Cascade will ask you to define Source Bypass Timer Count Attempts Abutment Dela Disconnect Dela Signal Type Frequenc Response Timer Pressure Freq Setpoint Timer Temp Shutdown Setpoint 6 Stop Delay 18 Digital Input 3 42 Lo Batt Voltage Timer Aux Input 1 Setpoint Timer Aux input 2 RPM Setpoint Preheat Timer Control Voltage Setpoint ll alli I AI cll Timer Output 1 oe N a Timer Output 2 Conversion Method Timer Output 3 Stop Timer Output 4 NOTE For further information on the parameters see Appendix A Tables in i this document Section 40 00 02 0724 01 25 11 10 2 System of Operation The sequences to be defined for system of operation determine the day to day normal operation of your equipment The following items from the Main Menu List allow you to define the system of operation Refer to the chapter titled Main Menu List Screen Definitions for information on field options you w
20. rt the CD101 CD into your computer CD drive The installation menu is displayed Click Next to continue ig Cascade PC Configuration Tool Setup Welcome to the Cascade PC Configuration Tool Setup Setup Wizard The installer will guide you through the steps required to install Cascade PC Configuration Tool Setup on your computer WARNING This computer program i protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the masimum extent possible under the law Cancel 2 You will be asked for a destination folder for the program You can accept the suggested directory or you can select a different directory by clicking Browse and browsing to the destination folder Once the destination folder is determined click Next to continue Note click Disk Cost to check disk space i Cascade PC Configuration Tool Setup Select Installation Folder The installer will install Cascade PC Configuration Tool Setup to the following folder To install in this folder click Nest To install to a different folder enter it below or click Browse Folder EA Program Files Pw Murph Cascade PC Configuration Tool Setup canci J _ lt Beck J E 3 To check to see your available disk drive space click Disk Cost The following screen is displayed When finished click OK
21. sistently bring you the highest quality full featured products we reserve the right to change our specifications and designs at any time Please read the following information before installing BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT e Read and follow all installation instructions e Please contact FW MURPHY if you have any questions Table of Contents BIER OCG UO aena a cin cece sanecstannacesGiceo unseen vent ens eeaesseaaseaee 1 MStar A 1 SV SES IMI ERS SIAN CIS epee ic dates tate and dated teense cio ete av ol cei ain seins saddindiag 1 INSTA AOMNSEUICHOMS niara A eee eieiaecteietetelenemeet aN 2 stalling USB Driver cic ice rosea ca acdc Sate chase a ena cneneeseextaeneta aes cdaiterta ss 4 ETON SAIN SS CG ia actoiac cay asterctartaatennaean misee aciaraulee E ON 4 SVAN AU OMe caccts aceasta ence cc ctenccuaccasenad ccecagan Guneeuay oven cunrovaaunioenanarorineiangenteseeo aaa paroeee eae 4 Programming NMOGGC inrano Ea Eai 6 Application GUI Overview ssasssnsnnnunnnnnnnnrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnn nnn nenen 7 Launching the Application ccccccccecceeceeceeceeeeeceeceeeeeeeeeaeeeecseeseeseeseeseeseeseeseeseeseeeees T Men s and TOOFBATS nornrareniinrn ia a eee T Navigating Cascade Configuration TOO cccccccccccececececeeeeeeeeeeceeeceeeseeseesseeeeeeeeees 9 Guidelines for Configuring the Cascade Configuration Tool ccecessessseeesee
22. source only 2 7 OO000 100 s digit 3 8 O 000 4 9 5 6 7 8 9 Table 2 LED States for Normal Operating Mode SlowBlink Fast Blink Auto Start Mode G Engine Running Engine is not Running Engine is Running Engine is cranking P ECU Status Non ECU configuration Valid CAN Activity no errors Error Bus Off Error Passive Failed Address Claim Active state Remote Start Crank Rest Remote start input is inactive and Remote Start active In Crank Rest or one of the prestart states manual start has not been initiated startdelay preheat waitecu wait rpm No J1939 data when ECU is on AUTO Manual Start Mode Low Oil Pressure Pressure is above setpoint or low oil Pressure is below setpoint or Fault code SPN 100 received AND ECU No pressure data ECU only pressure input is inactive low oil pressure input active warning shutdown active High Engine Temperature Temperature is below setpoint or high Temperature is above setpoint or high Fault code SPN 110 received AND ECU No temperature data ECU only engine temperature input is inactive engine temperature input is active warning shutdown active Engine speed below overspeed setpoint Engine speed above overspeed setpoint a ir se a ECU or loss of speed non Underspeed Engine speed above underspeed setpoint Engine speed below underspeed setpoint Overcrank Start Fail Failure to start has not occurred Overcrank start failure crank attempts exceeded Charge Fail Alternator warning
23. t including textual matter and illustrations is copyright protected by Murphy Industries LLC with all rights reserved c 2010 Murphy Industries LLC Eugine Controls amp Danela Comeressar Pats 860 North 9th Avenue Brighton CO 80603 Ph 303 659 5139 Fax 303 659 5309 www rjmann com
Download Pdf Manuals
Related Search