ME Remote Controller Mitsubishi Electric PAR
Contents
1. FILTER TEMP A Press and hold down at the same time for 2 seconds e While locked all the remote controller buttons cannot be operated When all the buttons are locked in the timer mode timer operation is performed even though the buttons are locked When locking unlocking all the buttons other than the ON OFF button E When the ON OFF button is pressed and held down for two seconds while pressing the FILTER button all buttons other than ON OFF button are locked or unlocked Lock other than ON OFF button Unlock FILTER ON OFF Press and hold down at the same time for 2 seconds e While locked buttons other than the ON OFF button cannot be operated When locked in the timer mode the timer operation is performed even though the buttons are locked 6 may be different the HEAT mode After one hour automatically returns to the horizontal position During swing operation remote controller display and airflow vane po sition cannot be synchronized There may not be an airflow function depending on the model In cases such as the following the liquid crystal display and unit airflow 1 When HEAT STANDBY or DEFROSTING is displayed 2 Immediately after heating operation Waiting for mode selection 3 When the room temperature is higher than the set2. y E Set the ON time by pressing the Time selection A or V button E Set the OFF time to display e display is displayed between 23 50 and 0 00 ON E Press the Timer selection button and set the display to 1 day timer mode or DAILY daily timer mode e Each time the button is pressed the timer mode is switched as shown below of 5 Ce ee noor O 1 day timer mode Daily timer mode Auto off timer mode The Auto off timer mode is skipped at the OFF window When performing OFF timer operation 1 day timer mode daily timer mode E Press the Time selection button and check Current time CLOCK and set the display to Ending time E Set the OFF time by pressing the Time selection A or V button E Set the ON time to display OFF 53 E Press the Timer selection button and set the display to 1 day timer mode or DAILY daily timer mode When performing ON OFF timer operation 1 day timer mode daily timer mode E See the setting when performing ON timer and OFF timer operation and check Current time CLOCK and set both the ON time and OFF time E Press the Timer selection button and set the display to 1 day timer mode or DAILY daily timer mode When performing AUTO OFF timer operation AUTO OFF timer mode E The Auto off
3. V button is pressed after the setting above the remote controller switches to the heat mode temperature selection window HEAT and LIMIT TEMP light on the display and the heat mode set temperature adjustment range is displayed The upper limit temperature value can be changed by pressing the Time selection A or V button the same as cool dry mode temperature selection Upper limit temperature adjustment range 17 C to 28 C 17 C lt gt 28 C for mid temperature indoor unit also The lower limit temperature 17 C is fixed Only the upper limit temperature can be changed 3 At the end of selection of each function release the remote controller function selection mode and display the OFF window by pressing the CHECK and Mode selection buttons at the same time for two seconds 4 Specifications Item Contents Size 120 H x 130 W x 19 D mm Weight 0 2 kg Power requirement DC30 V Power supplied from M NET transmission line Normally power is received from the outdoor unit over the indoor outdoor unit M NET transmission line Power consumption 0 5 W Environmental conditions Temperature 0 to 40 C humidity 30 to 90 RH No condensation Material PS afa MITSUBISHI ELECTRIC CORPORATION
4. Low Horizontal outlet Downward 45 Downward 60 Downward 85 Beadle e h hal Dr Not Swing y settable Horizontal after 1 hour The wind speeds that can be selected depend on the model Airflow setting Cool l Dry Heating when operation NOTES mode was changed Fan operation operation In cases such as the following the liquid crystal display and unit wind speed are different 1 When HEAT STAND BY or DEFROSTING is displayed 2 Immediately after heating operation while waiting for mode selec tion 3 When the room temperature is higher than the set temperature in the heating mode 4 Dry operation For 3 speed models a central controller wind speed display and the remote controller wind speed display may be different low B 5 ae MITSUBISHI ELECTRIC 5 22 35 if al sah 38S a H Temp il CON OFF u MOQ C gt my teres CLOCK ONAOFF h I N FILTER CO o as O D00 PAR F27MEA apem cP Jj The wind direction is displayed at 6 The following wind directions can be selected When you want to change the wind direction While the air conditioner is operating press the Airflow button e Each time the button is pressed the setting changes as shown be for When performing ON timer operation 1 day timer mode daily timer mode E Press the Time selection button and check Current time CLOCK and display Starting time
5. are controlled the contents of the master indoor unit are displayed on the remote controller The room temperature sensor position can be selected from INDOOR UNIT and REMOTE CONTROLLER The initial setting is INDOOR UNIT When you want to change the room temperature sensor position to REMOTE CONTROLLER con sult your dealer When no room temperature display was selected by remote control ler function selection the room temperature is not displayed ES 2 Wind speed and wind direction adjustment and fan operation When you want to change the wind speed E While the air conditioner is operating press the Wind speed button Each time the button is pressed the setting changes as shown be low The wind speed is displayed at 5 The following wind speeds can be selected a R Setting 1 Setting 2 Setting 3 Setting 4 Swing horizontal 0 horizontal 45 horizontal 60 horizontal 85 Wind speed Remote controller display LS S5 n Low Mid1 Mid2 High Display a 4 speed model C b h gt ba Pal Operation Wind i i i mode Speed Mid1 Mid2 High Hi g 7 Horizontal Downward Downward Downward 3 speed model h gt ba gt ha Heat fan IVM Swing outlet 45 60 85 l Mid2 Low High Mid1 High 2 inodel High Gool Mid1 Mid2
6. timer can only be set while the air conditioner is operating E Press the Timer selection button and set the display to AUTO OFF Auto off timer mode E Set the desired remaining time by pressing the Time selection A or V button 30 minutes units 30 minutes to 4 hours After remaining time setting the timer automatically starts When releasing timer operation E Press the Timer selection button and turn off the TIMER display Sas ee a Da ee Oo 1 day timer mode Daily timer mode Auto off timer mode The Auto off timer mode is skipped at the OFF window 4 Auto lock Remote controller buttons operation can be locked There are two kinds of auto lock 1 All buttons lock Locks all the remote controller buttons 2 Lock other than ON OFF button Locks all the remote controller buttons except the ON OFF button When auto lock is set CENTRALLY CONTROLLED flashes sa MITSURISHIELECTRIC re Camon fa 2 2 c2 EE z hal a oul 3E D HE TENP ON OFF eee Oo opens OOOO Fal J Cj MH SSE BBE a8 CHECK TEST Ho Moo PAR F27MEA TIMER SI When locking unlocking all buttons E When the TEMP A button is pressed two seconds successively while pressing the FILTER button all the remote controller buttons are locked or unlocked All buttons lock Unlock
7. Hr op R gt TEMP buttons OB aD on8 B ogre Oe ESE Wind speed button _ noogt REMAINDER 71 ieee TE Y Lower A Raise gan AGES S BG Da a DEFROST Cc NOTAVAILABLE _ LIMIT TEMP FILTER button 7 fete ONIOFF Timer selection button f amp MERA 7 CHECK button DROZ CLOCKON0F E al N FILTER Mode selection button E5 b as QJ Normally not used Sas a CHECK TEST la Ra e 20 cae TEST RUN button L Time selection buttons 7 Normally not used Y Return A Ahead Airflow button Louver button Ventilation button When one remote controller controls multiple indoor units if the master indoor unit has the selected function this message is not displayed Built in temperature sensor position 3 How to Operate 1 On off and operation mode selection and room temperature adjustment ae MITSUBISHI ELECTRIC S 22E o at bal TRNA a 1 if Teme i ON OFF C gt ogogo owner Paal X FILTER Oooo CG Sat BBE a8 CHECK TEST c CD o oO PAR F27MEA TIMER SET When starting operation E Press the ON OFF button e The ON lamp 1 and display light NOTE The restarting operation contents are shown below When you want to change the set temperature lt When you want to lower the room temperature gt E Press the TEMP V button lt When y
8. WT03299X01 MITSUBISHI ELECTRIC CITY MULTI Control System ME Remote Controller Instruction Book Thank you for purchasing a Mitsubishi CITY MULTI system CE PAR F27MEA To use your CITY MULTI system correctly and safely please read this book before use After reading this book keep it and the installation manual in a place where the final user can see them at anytime When the end user has changed forward this book and the instruction manual to the new final user Do not try to install or move this system by yourself Safety and functions cannot be ensured 1 Safety Precautions The following two symbols are used to dangers that may be caused by incorrect use and their degree A WARNING This symbol denotes what could lead to serious injury or death if you misuse the PAR F27MEA Z CAUTION This symbol denotes what could lead to a personal injury or damage to your property if you misuse the PAR F27MEA A WARNING Ask your dealer or technical representative to install the unit Any deficiency caused by your own installation may result in an electric shock or fire Do not move and re install the PAR F27MEA yourself Any deficiency caused by installation may result in an electric shock or fire Ask your distributor or special vendor for moving and installation Securely install in a place which can withstand the weight of the con troller If it is not enough the
9. When the remaining time reaches 0 00 the air conditioner stops When the Auto off timer mode is selected the next time the air conditioner is started the OFF timer operates automatically so that the timer can be used to turn off the air conditioner if you should forget When ON OFF operation from the central controller etc was restricted when timer operation was set the set ON OFF timer is not executed After the restriction is removed timer operation is performed at the ON OFF time When ON OFF operation was restricted during AUTO OFF timer operation the remaining time at the point operation was restricted is memorized and the air conditioner is stopped after the memorized remaining time from the time the restriction was removed A MITSUBISHI ELECTRIC ON OFF Chon woo oa j N FILTER CH MO 38E 8 CHECK TEST Cc CcCOoo PAR F27MEA TIMER SET When setting the current time E Press the Time selection button and display CLOCK e Each time the button is pressed the time is switched as shown below ON OFF Timer setting display example e 1 day timer mode ON u a C gt LILI Daily timer mode PAYG OFF 7 700 tect Auto off timer mode AUTO orr REMAINDER DEFA E OE wa REMAINDER No ee E Each time the Time selection A button is pressed the time advances on
10. at the same time for 2 seconds TEMP V button TEMP A button PROCEDURE 1 Set the air conditioner to the off state with the remote controller ON OFF button The remote controller display shifts to the OFF window display shown at the left 2 When the CHECK and Mode selection buttons are pressed and held down at the same time for two seconds the remote controller switches to the remote controller function selection mode and the OPERATION MODE DISPLAY SELECTION MODE window appears The other three modes can be selected by operating the TEMP V button or A button Display the mode whose function you want to change OPERATION MODE DISPLAY SELECTION MODE When you want to change the AUTO mode display e AUTO COOL HEAT flashes and ON or OFF lights Each time the Time selection A or V button is pressed in this state the ON and OFF display is switched Py T he Aj lt gt bee Ly i Time selection A V button ITA l J TN LIM When ON was selected AUTO COOL or AUTO HEAT is displayed during AUTO mode operation When OFF was selected only AUTO is displayed during AUTO mode operation ROOM TEMPERATURE DISPLAY SELECTION MODE When you want to change room temperature display no display 88 C flashes at the room temperature display and ON or OFF li
11. controller may drop and cause an injury Make sure that the controller is connected to a rated power supply If the controller is not connected to a rated power supply it may cause a fire or damage to the controller Stop the operation if any malfunction occurs If malfunction occurs burning smell etc stop the operation and turn off the power supply Contact the your dealer or technical representative immediate If the controller continues to operate after a malfunction occurs this may cause damage electric shock or fire To dispose of this product consult your dealer Never modify or repair the PAR F27MEA by yourself Any deficiency caused by your modification or repair may result in an electric shock or fire Consult with your dealer about repairs Stop the operation immediately and notify the your dealer if an error code is displayed or malfunction occurs Fire or damage may cause it the controller is operated in this condition Z CAUTION Do not install in any place exposed to flammable gas leakage Flammable gases accumulated around the body of PAR F27MEA may cause an explosion Do not wash with water Doing so may cause an electric shock or a malfunction Do not touch any control button with your wet hands Doing so may cause an electric shock or a malfunction Do not use the controller for special applications Do not use in any special env
12. e ON lamp and ERROR CODE flash trouble oc curred in the air conditioner and the air conditioner stops Jot down the unit number and error code and turn off the air condi tioner power and consult your dealer 6 How to select the remote controller functions ON lamp flashed a MITSUBISHI ELECTRIC When only ERROR CODE flashes ON lamp remains a steady light The air conditioner continues to operate but there is the possibility of trouble occurring Jot down the error code and consult your dealer In the remote controller function selection mode three functions can be selected and changed Select and change them as required 1 Operation mode display selection mode Automatic mode cool heat display selection When the AUTO operation mode was set by remote controller the indoor unit is judged from the room temperature and the cooling or heating operation is performed automatically In this case AUTO COOL or AUTO HEAT is displayed at the remote controller However AUTO can be displayed alone without the COOL or HEAT display 2 Room temperature display selection mode Room temperature display no display selection Normally the intake temperature is displayed at the remote controller but setting can be performed so that it is not displayed 3 Set temperature range limit mode Ordinarily the set temperature adjustment range can be freely s
13. e minute and each time the Time selection V button is pressed the time returns one minute lt 1 day timer mode 8 A M operation start lt Daily timer mode 5 P M daily operation stop lt Auto off timer mode Operation stop when 2 hours remain When the button is held down the time advances or returns continuously The time changes in 1 minute units 10 minutes units 1 hour units order e About 10 seconds after the end of setting the remote controller display goes off blow directly on the controller as this may cause in fire Do not clean the unit using benzene thinner or other chemicals It may cause discoloration or other damage If the unit should become par ticularly dirty apply a mild cleaner that has been diluted with water to a soft cloth and wipe the unit clean Be sure to wipe away any residual moisture with a dry cloth Do not dismantle the unit It is dangerous to touch the internal circuit board It may cause a fire or mal function When a power failure occurs the current time is reset Reset the clock NOTE When an operation button is pressed if the indoor unit does not have that function NOT AVAILABLE flashes OPERATION SECTION ON OFF lamp p ON OFF button ae MITSUBISHI ELECTRIC CENTRALLY CONTROLLED 1
14. et to the 19 C to 30 C range for cooling and dry and the 17 C to 28 C range for heating However the lower limit temperature can be preset to an arbitrary value for cooling and dry and the upper limit temperature can be preset to an arbitrary value for heating If the set temperature range for cooling and dry is set to a value higher than normal and the set temperature range for heating is set lower than normal in this way overcooling and overheating can be prevented and energy can be saved When the set temperature adjustment range was changed from the normal set temperature adjustment range by remote controller connected to a cooling heating simultaneous air conditioner with an AUTO mode the AUTO mode cannot be selected with the Mode selection button OFF window OT LO A MITSUBISHI ELECTRIC fei Remote controller function selection modes Remote controller function selection mode transition Xa Ee Operation mode display selection mode dop C5 OT 1O Boas SA T Room temperature display selection mode II Set temperature adjustment range limit mode cool dry T LJ Set temperature adjustment range limit mode heat Remote controller OFF window display Press and hold down the CHECK and Mode selection buttons
15. ghts Each time the Time selection A or V button is pressed in this state the ON and OFF display is switched aac ee rid Time selection A V button me o When ON was selected the room temperature is continuously displayed in the ON window When OFF was selected the room temperature is not displayed in the ON window SET TEMPERATURE RANGE LIMIT MODE When you want to change the set temperature adjustment range 1 Cool dry mode temperature selection COOL DRY and LIMIT TEMP light on the display and the set temperature adjustment range in the cool dry mode is displayed The lower limit temperature of the set temperature display flashes This temperature value can be set and changed Lower limit temperature adjustment range 19 C lt gt 30 C Mid temperature indoor unit 14 C lt gt 30 C Upper limit temperature 30 C is fixed Only the lower limit temperature can be changed bod OVE an au l o When set temperature adjustment range in cool dry mode is 19 C to 30 C 2 Each time the Time selection A or V button is pressed the lower limit temperature value is increased or decreased Set it to the desired set temperature adjustment range oe r LI 2 yk Lo o TTEN When set temperature adjustment range was set to 24 C to 30 C 3 When the TEMP
16. ironment Using in any place exposed to oil including machine oil steam and sulfuric gas may deteriorate the performance significantly or give damage to the com ponent parts Do not press any control button using a sharp object Doing so may cause an electric shock or a malfunction This product is designed for use with the CITY MULTI CONTROL SYSTEM Do not use the system for other air condition management operation or appli cations It may cause malfunctions Operate the controller within the specified temperature range Observe the specified temperature range when operating the controller If the controller is used outside the specified temperature range it may cause serious damage Be sure to check the operation temperature range in the operation manual Do not apply insecticide or flammable sprays to the controller Do not place flammable spray near the controller and make sure it does not Do not pull or twist the transmission line It may cause a fire or malfunction 2 Part Names he CENTRALLY CON TROLLED display TIMER DAILY AUTO OFF Display Displayed when air conditioner operation is prohibitted by a cen tral controller etc When the re mote controller buttons are the timer is set Displays the timer mode when There are three timers modes Current Starting time display Ending REMAINING timer set times Dis
17. ou want to raise the room temperature gt E Press the TEMP A button e The set temperature changes 1 C each time the button is pressed When stopping operation E Press the ON OFF button The ON lamp i and display go off When selecting the operation mode E Press the Mode selection button while the air conditioner is oper ating e The setting is switched each time the button is pressed The operation mode is displayed at 2 ee eee aca The auto and heating functions may not be installed depending on the outdoor unit model Remote controller settings The set temperature is displayed at 3 The following specified temperatures can be set Operation Cool dr A Last operation mode R Heat operation Auto operation Fan Temperature setting Last set temperature 19 14 to 30 C 17 to 28 C 19t028 C Cannot be set Wind speed Last set wind speed NOTE tt Horizontal outlet When LIMIT TEMP is displayed on the screen the specified tempera 3 Operation ture range is limited Therefore the temperature range that can be AIMOW mode 0 Last setting changed becomes narrow of ae Room temperature display During operation the intake temperature is displayed at The display range is 8 to 39 C When this range is exceeded the room temperature display flashes at 8 C or 39 C When multiple indoor units
18. plays the current time and 3 Senser display Displayed when the remote locked this display flashes 1 day timer daily timer and auto off timer One of these modes When the timer is operating dis plays the normal time and the controller sensor is used can be selected Set temperature display Displays the set temperature DAILY For description purposes all the displays are assumed to be on 1I LINLI STAND BY C DEFROST Py CENTRALLY CONTROLLE iH a ON OFF aw NN oF time stating ending or remaining AUTO OFF aoc Sie II 7 it REMAINDER bi a i e I on oo B38 a NOT AVAILABLE FILTER display Indicates that it is time to clean the filter LIMIT TEMP display Displayed when the set tem perature range is controlled by remote controller functions se lection Operation mode Airflow display Displays the operation mode Displays the outlet air direc tion Louver display Displays operation of the swing louver It is not dis played when the louver is stopped a DISPLAY SECTION Room temperature display Displays the intake temperature Displayed when low downward is selected at cooling and elec tronics dry operation Differ
19. s with the model After one hour the display goes off and swing also switches Ventilation display Displayed during fan operation while the air conditioner is op display Wind speed erating l Displayed while the power is on ASP Set effective for 1 hr et effective for r Displays the selected wind display NOT AVAILABLE speed display When the button of a function that is not installed at the indoor unit was pressed this display flashes simultaneously with the corresponding function display A 3 How to operate the timer There are the following three timer modes Select one of them 1 1 day timer mode In this mode the ON and OFF timers 10 minute units can each be set to one time within 24 hours This mode has the following three setting methods ON timer operation Timer only starts the air conditioner OFF timer operation Timer only stops the air conditioner ON OFF timer operation Timer both starts and stops the air conditioner 2 Daily timer mode Operation of this mode is the same as that of the 1 day timer mode However timer operation can be set to the same time each day in accordance with the set ON OFF timer time ON OFF timer each 1 time daily 3 Auto off timer mode The OFF timer can be easily set in 30 minute units 30 minutes to 4 hours range
20. temperature in Fan operation lt When operating fan interlocked with indoor unit gt When the indoor unit is operated the fan is automatically operated also Fan operation is displayed at 7 lt When operating fan only while indoor unit stopped gt E While the air conditioner is stopped press the Ventilation button The ON OFF lamp 1 lights and fan operation is displayed at 7 lt When you want to change the fan wind speed gt E Press the Ventilation button Each time the button is pressed the wind speed is changed as shown below Remote controller display Off no display NOTES Depending on the indoor unit and fan model the indoor unit may operate even when only the fan was operated When NOT AVAILABLE is displayed when the Ventilation button was pressed the fan is not interlocked 5 Other displays and flashing CENTRALLY CONTROLLED display A MITSUBISHI ELECTRIC CENTRALLY CONTROLLED Be Sal 50 e Displayed when operation is controlled by central controller etc Restricted operations are shown below ON OFF including timer operation Operation mode Set temperature May also be individually restricted Operation mode flashing A MITSUBISHI ELECTRIC N l 4 ZAF 7H Ty Ete rs r COG hal lt When flashes contin
21. uously gt e Displayed when another indoor unit connected to the outdoor unit is already operating in a different operation mode Match with the operation mode of the other indoor unit lt When mode switched after display flashes gt e Displayed when operation mode is restricted for each season by cen tral controller etc Use another operation mode FILTER flashing ae MITSUBISHI ELECTRIC e Indicates that the filter needs cleaning Clean the filter When resetting FILTER display When the FILTER button is pressed two times successively after cleaning the filter the display goes off and is reset When two or more different types of indoor unit are controlled the clean ing period differs with the type of filter When the master unit cleaning period arrives FILTER is displayed When the filter display goes off the cumulative time is reset FILTER indicates the cleaning period when the air conditioner was used under general indoor air conditions by criteria time Since the de gree of dirtiness depends on the environmental conditions clean the filter accordingly The filter cleaning period cumulative time differs with the model ERROR CODE flashing ae MITSUBISHI ELECTRIC d mi oe Tooolt a0 oon 10007109 oor 4 Vg T TVERROR CORD i ON OFF S unit number roe aN N When both th
Download Pdf Manuals
Related Search