Getting Started fi-5120C/fi
Contents
1. The alarm status remain displayed even after the scanner has been turned off and on again Are the glass dirty Turn off and on the power button If this does not eliminate the alarm status contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider Clean the glass as instructed in the Operator s Guide 3 Daily Care The generated image shifts or is distorted Are the documents loaded correctly Load the documents correctly Quality of generated image is unsatisfactory Are the glass clean Clean dirty locations Multi feed frequently occurs Do the documents satisfy the Docu ment Quality and the Multi feed Detection Conditions in the chapter 6 of the fi 5120C fi 5220C Operator s Guide Use the documents that satisfy the Document Quality and the Multi feed Detection Condi tions in the chapter 6 of the fi 5120C fi 5220C Operator s Guide Are the documents placed properly in the ADF paper chute Fan the documents before scanning Correctly align the document stack and load them on the ADF paper chute Refer to 2 1 Installing the Scanner on page 3 for details Is the stack of document thicker than 5 mm Reduce the number of sheets of the stack to a thickness of 5 mm or less Is the Pad ASSY dirty Clean the Pad ASSY Refer to Operator s Guide in 3 3 Cleaning the ADF Is the Pad ASSY worn out Replace the Pad ASS2. P3PC 1312 04EN as fi 5120C fi 5220C Image Scanner Getting Started cO FUJITSU CONTENTS E Regulatory Information cconnnncccccnnnnannncnnncnnnannnennnnanananennns ii E Note Liability seca ia ee Ree iii E Safety Precautions ccccceeeeseeceeeeeeseeeeeeeeeeeeeeeeseeeaeeeeeeesees V Chapter1 PREPARING THE SCANNER cc ssceeeeeeeeees 1 1 1 Checking the Contents of the Scanner Package 1 1 2 Names and Functions of Parts ccseeeeeeseeeeeeeeeeeeees 1 1 3 Operator Pad anise ccna 2 Chapter2 INSTALLATION OF THE SCANNER 005 3 2 1 Installing the Scanner ccccceeeeeeeeeeeeee sees eeeeeseeeeeeeeeeeeees 3 2 2 Connecting the Scanner to Your PC ccccceeeeeeeeeeeees 4 2 3 Installing the Scanner Application ooonnccncccconnonnnennnns 5 Appendix1 TROUBLESHOOTING cccccseceeseeeeeeeeeeeees AP 1 Appendix2 DAILY CARE ci n AP 4 Appendix3 REPLACING CONSUMABLEG 000 AP 5 fi 5120C fi 5220C Image Scanner Getting Started INTRODUCTION Thank you for purchasing the fi 5120C fi 5220C Duplex Color Scanner product This document describes how to handle fi 5120C fi 5220C Duplex Color and basic operation methods Before you start using fi 5120C fi 5220C Duplex Color be sure to thoroughly read this manual to ensure correct use The Operator s Guide is stored on the Setup Disk The guide provides usefu
3. installation starts and the Setup dialog box appears LD Adobe Acrobat 8 Standard ADOBE ACROBAT 8 STANDARD Install Adobe Acrobat 8 Standard 2 Read Me Browse CD Contents gt gt C Read License Agreement Always show AutoPlay 3 Inthe dialog box below click the Next button ig Adobe Acrobat 8 Standard Setup ADOBE ACROBAT 8 STANDARD 4 Install the application following the on screen instructions ele For information about how to install Adobe Acrobat refer to Read Me that you can view when Readme is clicked in the dialog box shown in step 2 For information about how to operate Adobe Acrobat refer to the Help topics in Adobe Acrobat ATTENTION Y ATTENTION y Notes for using Adobe Acrobat When scanning a paper document and converting the image to PDF using Adobe Acrobat unexpected images may be out put when 1 Setting Edge Shadow Removal in Acro bat and setting Digital Endorser or Black Background options in the TWAIN driver at the same time Letter strings embedded in the image or the background may be missed Solution 1 Set Edge shadow removal to OFF or set any option other than Adaptive for Color Grayscale and or Monochrome under Compression by selecting File gt Create PDF gt From Scamner gt Optimization Options in Acrobat Solution 2 Adjust the scanning density in the TWAIN driver 2 Setting Adap
4. os After you select Yes for installing Error wy Recovery Guide the Choose Setup Lan guage dialog box appears Select a lan guage and follow the on screen instructions The Error Recovery Guide dialog box is automatically displayed when the installation is complete Wait until the installation of the ISIS starts 7 Select a language for the installation on the Choose Setup Language dialog box and then click the Next button Fujitsu ISIS Drivers InstallShield Wizard Choose Setup Language Select the language for the installation from the choices below nglish French Standard German Italian Japanese Korean Russian Spanish ves 8 Install the driver following the on screen instructions 9 When you see the InstallShield Wizard Com plete dialog box click the Finish button Y our computer will restart and detect the scanner Do not remove the Setup CD ROM from the CD drive until your personal computer completely starts up again a Depending on the operating system you are yy using you may need to do the following Windows 2000 If you see the Digital Signature not Found dialog box click Yes Windows Vista If you see the Found New Hardware dialog box select Locate and install driver soft ware and then in the User Account Control dialog box click the Continue button if it is displayed Now the installation of the scanner driver is completed NW Installin
5. When cleaning the scanner parts dampen a cloth with modest quantities of the cleaner In addition wipe off the cleaner completely with a soft lint free cloth to leave no residue on the surface of the cleaned parts MW Parts to Clean and When Part to clean Standard Cleaning Cycle Pad ASSY Clean these parts after every Pick roller 1 000 scans Feed rollers Plastic rollers Glass Cleaning Parts Remarks Materials Number Cleaner F1 PA03950 1 bottle 0352 Moisten the cloth with this fluid and wipe the scanner clean 1 Cleaning Wipe PA03950 24 sheets pack 0419 Pre moistened with Cleaner F1 Cleaning Wipes are used instead of moistened cloths 1 Lint free dry cloth Commercially available one 1 For details about cleaning materials contact the FUJITSU scanner dealer where you purchased the scanner AP 4 ATTENTION Y The scanner must be cleaned frequently if you scan any of the following type of paper sheets e Documents of coated paper e Documents that are almost completely covered with printed text or graphics e Chemically treated documents such as carbonless paper e Documents containing a large amount of calcium carbonate e Handwritten documents For details on the cleaning the ADF refer to 3 3 Clean ing the ADF in fi 5120C fi 5220C Operator s Guide on the Setup CD ROM Appendix3 REPLACING CONSUMABLES
6. connecting to an USB hub use the first stage USB hub that is closest to the computer If you use the second or later hub stages the scanner may not operate correctly e Ifyou connect the scanner with USB 2 0 it is required that the USB port and Hub are compliant with USB 2 0 The scan ning speed may slow down if it is con nected with USB1 1 NW Connecting with the SCSI Inter face Cable When using the scanner with SCSI interface a commer cially available SCSI interface cable and SCSI card must be purchased in addition e SCSI interface cable Use a connector which complies with Ultra SCSI A 50 Pin Contact Shielded High Density SCSI Device Connector is required e SCSI card Find the recommended SCSI card information in the Fujitsu web site FAQ http imagescanner fujitsu com NENA AC Aiei e When connecting the SCSI interface Q cable turn the scanner off Be sure to first connect the SCSI interface cable and then turn on the power of the scan ner and the personal computer e In a SCSI daisy chain formation con nect the scanner so that it is the termi nated device 1 Insert the SCSI interface cable into the inter face connector until both sides click 2 Connect the other end of the cable to the per sonal computer HBHRHHHHHHHHHHHEHE ESE are Be careful not to bend the pins of the SCSI yy cable when connecting to the scanner fi 5120C fi 5220C Image Scanner Getting Started 4 ete T
7. in High safety Applications This product has been designed and manufactured on the assumption that it will be used in office personal domestic regular industrial and general purpose applications It has not been designed and manufactured for use in applications simply called high safety applications from here on that directly involve danger to life and health when a high degree of safety is required for example in the control of nuclear reactions at nuclear power facilities automatic flight control of aircraft air traffic control operation control in mass transport systems medical equipment for sustaining life and missile firing control in weapons systems and when provisionally the safety in question is not ensured The user should use this product with adopting measures for ensuring safety in such high safety applications PFU LIMITED assumes no liability whatsoever for damages arising from use of this product by the user in high safety applications and for any claims or compensation for damages by the user or a third party About the Use of Mercury Lamp s inside this product contain mer cury and must be recycled or disposed of according to local state or federal laws To avoid unexpected injuries eDo not put the substance contained in the lamp in your mouth as it has mercury fi 5120C fi 5220C Image Scanner Getting Started eDo not breathe the chemical liquid contained in the scanner lamps eDo not in
8. operate the equipment EN The use of a shielded interface cable is Q required to comply with the Class B limits of Part 15 of FCC rules The length of the AC cable must be 2 meters 6 6 feet or less Canadian DOC Regulations This digital apparatus does not exceed the Class B limit for radio noise emissions from digital apparatus set out in the Radio interference Regulations of the Canadian Department of Communications This Class B digital apparatus complies with Canadian ICES 003 Le pr sent appareil num rique n met pas de parasites radio lectriques d passant les limites applicables aux appareils num riques de la classe B et prescrites dans le R glement sur le brouillage radio lectrique dict es par le Minist re des Communications du Canada Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Bescheimigung des Herstellers Importeurs F r den fi 5120C fi 5220C wird folgendes bescheinigt eIn Ubereinsstimmung mit den Bestimmungen der EN45014 CE funkentst rt eMaschinenl rminformationsverordnung 3 GPSGV Der h chste Schalldruckpegel betr gt 70 dB A oder weniger gem EN ISO 7779 International ENERGY STAR Program As an ENERGY STAR Partner PFU LIMITED has determined that this product meets the ENERGY STAR guidelines for energy efficiency The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving t
9. store where you purchased the scanner Do not put liquids inside the scanner Do not insert or drop metal objects in to the scanner Do not scan wet documents or documents with paper clips or staples Do not splash or allow the scanner to get wet If foreign objects water small metal objects liquids etc get inside the scanner immediately turn off the scanner and dis connect the power plug from the power out let Then contact the store where you bought the scanner or the Maintenance Ser vice Center Pay particular attention to this warning in households where there are small children A gt Do not touch the inside of the scanner unless necessary Do not take apart or modify the scanner The inside of the scanner contains high voltage components Touching these components might cause electric shock or fire Do not use the scanner if you smell a strange odor If you detect heat coming from the device or detect other problems such as smoke strange smells or noises immediately turn off the scanner and then disconnect its power plug Make sure that any smoke coming from it has stopped before contacting the store where you bought the scanner or an authorized FUJITSU scanner service provider A ZN CAUTION Do not install the scanner on unstable surfaces Make sure that the scanner is installed on a flat level surface and that none of its parts extend beyond the surface top such as a desk or ta
10. you may need to do the follow ing Windows 2000 If you see the Digital Signature not Found dialog box click the Yes button Windows Vista If you see the Found New Hardware dia log box select Locate and install driver software and then in the User Account Control dialog box click the Continue button if it is displayed Now the installation of the scanner driver is completed HHRHHHHHHHHHHEHEH EE amp To confirm whether the installation was i ATTENTION 3 E 7 Select a language used for installation on yy successful perform a scanning operation Choose Setup Language window and click with an application that complies with the Next TWAIN regulations such as ScandAll j PRO Scanner Utility for Microsoft Windows InstallShield Wizard N AOo n p a w O E OoaDpnapa n pnn n n A p oO Choose Setup Language Select the language for the installation from the choices below English French Standard German Italian Japanese Korean Russian Spanish 7 8 Install the application following the instructions on the window 9 When the InstallShield Wizard Complete win dow appears click Finish fi 5120C fi 5220C Image Scanner Getting Started 6 NW Installing ScandAll PRO ScandAll PRO is software for scanning images which is in compliance with both TWAN ISIS standards Using FUJITSU TWAIN 32 or FUJITSU ISIS together with ScandAll PRO allows you to create document images gu Be sure to log
11. 0 8 268 Length 11 693 vv Contrast ss Advance Preview Reset tion Help About Data Size about 1 1MB 12 To use FUJITSU ISIS On the dialog box below configure scanning set tings and then click the OK button Properties for Fujitsu on STI 0005 Main Layout Image Processing Paper Handling Gamma Color Dropout Compression About Image Mode Dots per inch Camera 300 Jhon ingest A O Front Image 2 C Back Image 1 E Back Image 2 Fixed Black and White 16 level Grayscale 256 level Grayscale v 24 bit Color Brightness Auto Detect 16 level Grayscale Auto Detect 256 level Grayscale Auto Detect 24 bit Color 1 Contrast Auto Cancel Default gt You are returned to the Scan Settings dialog box 12 Click the Scan button ete When you are using FUJITSU TWAIN 32 a you may see the TWAIN Driver setup dia G log box again If so click the Scan button on the dialog box gt The document is scanned and the scanned image is displayed in the ScandAll PRO window If the scanned document image is displayed in the win dow it means that the scanner driver is installed prop erly 13 Appendix TROUBLESHOOTING EW Troubleshooting checklist Symptom Check this item Remedy Scanner does not turn on Have you pressed the power button on Push the power button in to turn the sc
12. 20C and then click the Select button Select Scan on the menu and then select Scan Settings fi 5120C fi 5220C Image Scanner Getting Started In the Scan Settings dialog box clear the Save to file checkbox Scan Settings C Save to file File Name File Format Color Format Compression Document File Overwrite Waming Number of pages to scan Scan all O Scan the specified number of pages v Show confirmation when there is no paper on ADF Show TWAIN dialog before each batch scan process Y You only check the operation now so you H rey do not have to save to file 10 Click Scanner Settings gt A setup dialog box appears for you to config ure scanner driver settings Configure scanner settings such as the resolu tion and paper size To use FUJITSU TWAIN 32 On the dialog box below configure scan settings and then click the OK button Y TWAIN Driver 32 Or a eee ae Oe Le maga Scanner 64MB Browse Seting Fies 00 Curent Setting Config Resolution Scan Type E 300 x 300 bs ADF Front Side iz Pi ET H api Paver Size I Predefine 14 A4 210x297mm hie ee ok e ae e poda clado r I Enable Muli Image Front iz Image Mode Brightness AZ Black e White Black White Threshold r Static Threshold Scanning Areal inch Left 0 000 Top 0 00
13. The glass surface inside the The illustration below demonstrates the locations of the ZAWARNING ADF becomes hot during the replacement parts Refer to Chapter 4 Replacing Con operation Before replacing the sumables fi 5120C fi 5220C Operator s Guide on the consumables turn its power off Setup CD ROM and unplug the AC adapter from the outlet Wait at least 15 min utes NW Replacing the Pad ASSY A NW Consumables and Replacement Cycles Below are specifications of consumable items and their recommended replacement cycles Description Parts Standard P Number Replacement Cycle Pad ASSY PA03289 After 50 000 scans or 0111 one year Pick Roller Pick roller PA03289 After 100 000 sheets 0001 or one year To purchase consumables contact the store where you purchased the scanner or an authorized FUJITSU scan ner service provider The replacement cycles above are rough guidelines when using A4 or Letter woodfree or wood containing paper 64 g m2 17 lb This cycle varies according to the type of paper and how frequently the scanner is used and cleaned NONE ER wU an Use only above specified consumables Do not use other consumables fi 5120C fi 5220C Image Scanner Getting Started AP 5 fi 5120C fi 5220C Image Scanner Getting Started P3PC 1312 04EN Date of issuance November 2009 Issuanc
14. Y Refer to Operator s Guide in 4 2 Replacing the Pad ASSY fi 5120C fi 5220C Image Scanner Getting Started AP 1 Symptom Check this item Remedy Paper is not fed pick error occurs frequently or docu ment stops midway The generated images are elongated Do the documents satisfy the Docu ment Quality and the Multi feed Detection Conditions in the chapter 6 of the fi 5530C Operator s Guide Use the documents that satisfy the Document Quality and the Multi feed Detection Condi tions in the chapter 6 of the fi 5530C Operator s Guide Is the Pick roller dirty Clean the Pick roller Refer to Operator s Guide in 3 3 Cleaning the ADF Is the Pick roller worn out Change the Pick roller Refer to Operator s Guide in 4 3 Replacing the Pick Roller Is there any dirt or dust in the document feed path Are the Feed rollers dirty Remove any dirt or dust from the document feed path Clean the Feed rollers Refer to Operator s Guide in 3 3 Cleaning the ADF Have you adjusted the scan scale For Windows 2000 WindowsXP select Scan ners and Cameras in the control panel then click the Device Set tab to adjust scale There is a shadow on the leading edge of the gener ated image Are the Feed rollers dirty Clean the Feed rollers Refer to Operator s Guide in 3 3 Cleaning the ADF Have you adjusted the offset the scan n
15. anner Are the AC cable and AC adapter prop erly connected to the scanner Correctly connect the AC cable and the AC adapter Disconnect the AC cable and the AC adapter from the scanner then connect them again If this does not restore the power supply contact the store where you purchased the scanner or an authorized FUJITSU scanner service provider Are you using the correct AC cable and AC adapter supplied with the scanner from the manufacture You must use the AC adapter and cable supplied with your scanner by the manufacture Please get the correct AC adapter and cable to connect to your scanner Scanning does not com mence Vertical lines appear in the generated image of the scanned document Are the documents loaded properly on to the ADF paper chute Realign and reload the documents on to ADF paper chute Is the ADF closed completely Close the ADF completely Is the USB cable or SCSI cable con nected securely Connect the cable When a USB hub is used check the hub s power supply When using a SCSI interface Is SCSI ID set correctly Use the SCSI ID switch at the rear of the scanner to set the SCSI ID Does the Function Number display indi cates an alarm or an error When the Function Number display indicates an alarm or an error refer to the Chapter 5 TROU BLESHOOTING in the fi 5120C fi 5220C Operator s Guide for removing the alarm or the error
16. bed above are as follows e Uninstall or Change a program gt Unin stall or Change W Checking the Operation of the Scanner Driver 1 Load the document on the scanner 2 Launch ScandAll PRO From the start menu select All Programs gt Fujitsu ScandAll PRO gt Fujitsu ScandAll PRO gt ScandAll PRO starts up 3 In ScandAll PRO select Tool on the menu and then select Preferences 2 ScandAll PRO Untitled File Scan Edit View Page Zoom MA Help Preferences Setup Filters gt The Setup dialog box appears 4 On the Scan tab select a driver To check the operation of FUJITSU TWAIN 32 select TWAIN To check the operation of FUJITSU ISIS select ISIS Print Scan View HotKey Event Device Driver O IWAIN Olsis Report Scan Result Do not output Temporary Directory E Documents and Settings furuse Local Settings T emp Click the OK button to close the Setup dialog box In ScandAll PRO select Scan on the menu and then select Select Scanner ScandAll PRO Untitled File EGET Edit View Page Zoom Tool E Scan Scan Settings Ctrl N ES Batch Scan Settings Ctrl B Select Scanner Select a scanner in the displayed dialog box To use FUJITSU TWAIN 32 Select FUJITSU fi 5 120Cdj fi 5220Cdj and then click the Select button To use FUJITSU ISIS Select Fujitsu fi 5120C fi 52
17. ble Do not install the scanner on unstable surfaces Install the scanner on a level surface that is free of vibration to prevent it from falling Install the scanner on a strong surface that will support the weight of the scanner and other devices OS U o not block the ventilation ports Do not block the ventilation ports Blocking the ventilation ports generates heat inside of scanner which may result in fire or scanner failure Do not place heavy objects or climb on top of the scanner Do not place heavy objects on the scanner or use the scanner s surface top to perform other work Improper installation might cause injuries and equipment failure Firmly insert the power plug Firmly insert the power plug as far it can go into the power outlet Q Avoid any contact when scanner is in se c Avoid touching any scanner mechanism during scanning since this may cause injuries gt Do not use the scanner immediately after moving it from a cold place into a warm room Do not use the device immediately after moving it from a cold place into a warm room Condensation may occur which might lead to scanning errors Let the device dry about one or two hours before you use it Before moving the scanner disconnect the power plug from the power outlet E Do not move the scanner with the power and interface cables connected as this can damage the cables which can later cause fire e
18. cinerate crush or shred the lamps or scanner parts Trademarks Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation in the United States and or other countries ISIS and QuickScan are trademarks or registered trademarks of EMC Corporation in the United States Adobe the Adobe logo and Acrobat are either registered trademarks of Adobe Systems Incorporated in the United States and or other countries Other product names are the trademarks or registered trademarks of the respective companies How Trademarks Are Indicated In This Manual References to operating systems OS and applications are indicated as follows Windows 2000 Microsoft Windows 2000 Pro fessional operating system Windows XP Microsoft Windows XP Professional operating system 32 64 bit Microsoft Windows XP Home Edition operating system Windows Microsoft Windows Server Server 2003 2003 Standard Edition operating system 32 64 bit Windows Vista Microsoft Windows Vista Home Basic operating system 32 64 bit Microsoft Windows Vista Home Premium operating system 32 64 bit Microsoft Windows Vista Business operating system 32 64 bit Microsoft Windows Vista Enterprise operating system 32 64 bit Microsoft Windows Vista ultimate operating system 32 64 bit Where there is no distinction between the different versions of the above operating system the general te
19. ction connector fi 5220C USB Interface connector o o 0 0 6 6 0 0 0 0 0 0 090 00 000 oo ooo o o o onoono 000000 0 00 to too ooo 0 00 0 0 Security SCSI ID Slot switch DC inlet SCSI Interface connector USB Interface connector E Removable Parts Parts that can be removed from the scanner are dis played below Sheet guide Gg fi 5220C only Document cover 1 3 Operator Panel The operator panel is located on the right side of the scanner This panel comprises of a Function Number display four buttons and a LED Function Number display Function Send to Scan __ Power button Y LED Name Function Function Number display Indicates the function Num ber and error status Buttons Function Changes the Function acti vated by the Send to button Send to Launches the linked applica tion software Scan Power button Turns the scanner ON and OFF LED Lights when the scanner is turned ON About the settings on the launcher refer to FUJITSU TWAIN32 scanner driver help and the fi 5 120C fi 5220C Operator s Guide in the Setup CD ROM E Indications on the Function Number Display No Descriptions L
20. e responsibility PFU LIMITED e Copying of the contents of this manual in whole or in part and copying of the scanner application is forbidden under the copyright law e The contents of this manual are subject to change without notice e PFU LIMITED is not liable whatsoever for any damages resulting from use of this scanner and procedures described in this manual profit due to defects and any claims by a third party
21. g QuickScan Pro QuickScan Pro is image capturing software based on the ISIS standard By using this software together with FUJITSU ISIS you can scan documents with the scan ner Follow the procedure below to install the trial ver sion of QuickScan Pro that comes with this scanner HBHRHRHBRHEHHHHHHEHHEHE EB cing Be sure to log on as a user with Adminis yy trator privileges HBHRHRHHRHHHEHHHEHHEHE EB 1 Insert the Setup CD ROM into the CD drive gt lt SETUP DISK STARTUP SCREEN gt appears 2 Click INSTALL PRODUCTS and then click QuickScan Pro Trial 3 Inthe Welcome to the InstallShield Wizard for QuickScan 4 5 dialog box click the Next but ton fi 5120C fi 5220C Image Scanner Getting Started 8 4 Type in necessary information in the Customer Information dialog box and then click the Next button i QuickScan 4 5 InstallShield Wizard Customer Information Please enter your information User Name Organization Serial Number ses net gt ATTENTI N QuickScan Pro included in the Setup yy CD ROM is a trial version that can be exe cuted 30 times before it is disabled If you wish to continue using this product please consider purchasing full version When you install the trial version use the dis played Serial Number 5 Install the application following the on screen instructions Error Recovery Guide The Error Recovery Guide i
22. he factory default setting for SCSI ID is aN 5 If the SCSI ID of another SCSI device is C set to the same ID change either the scan ner s SCSI ID or SCSI ID of the other SCSI device Set the SCSI ID using the SCSI ID switch on the back of the scanner SCSI ID 2 3 Installing the Scanner Application For scanning documents with this scanner both scanner driver and image capturing application software called application hereafter must be installed on your PC The following scanner drivers and applications are pro vided e Scanner Driver FUJITSU TWAIN 32 Scanner Driver FUJITSU ISIS Scanner Driver e Scanning application ScandAll PRO for FUJITSU TWAIN 32 QuickScan Pro for FUJITSU ISIS Install the appropiate scanner driver for the application you will use The following sections descri be installa tion of each driver and application For FUJITSU TWAIN32 Scanner Driver NW Preparation Confirm the following items before installing the appli cation e Take out the Setup CD ROM from its pack age but do not insert the Setup CD ROM into the CD driver yet e Connect the scanner correctly to your PC HINT ey e Uninstall any older versions of FUJITSU TWAIN 32 driver if already installed For details on how to connect the scanner refer to 2 2 Connecting the Scanner to Your PC on page 4 HBHRHHHHHEHHHHHHHHE GI Uninstall Scanner Utility for Microsoft Win a yl d
23. hrough the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of products with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations ENERGY STAR E Note Liability BEFORE USING THIS PRODUCT PLEASE READ THIS MANUAL CAREFULLY IF THIS PRODUCT IS NOT USED CORRECTLY UNEXPECTED INJURY CAN OCCUR TO USERS OR BYSTANDERS Keep this manual in a safe place so that it can be easily referred to during use of this product While all efforts have been made to ensure the accuracy of all information in this manual PFU assumes no liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual its updates or supplements whether such errors are omissions or statements resulting from negligence accidents or any other cause PFU further assumes no liability arising from the application or use of any product or system described herein nor any liability for incidental or consequential damages arising from the use of this manual PFU disclaims all warranties regarding the information contained herein whether expressed implied or statutory Use
24. ights only one time upon turning on the scanner Indicates that the scanner has been turned ON and is being initialized Indicates that initialization will soon be completed oO vo Indicates that initialization has been completed successfully This status is called Ready Status U Indicates that a temporary error occurred when documents were being scanned A number appear ing in alternation following the U i e 1 or 2 etc refers to the type of error To return the scanner to the ready status 1 press Scan or Send to button E Indicates that a device hardware alarm has occurred during scanning of documents E and the alarm Number 0 to 9 A c d and F will appear alternately To return the scanner to the ready status 1 press Scan or Send to button If this alarm occurs turn the power off and on again If the alarm continues after turning the power on again contact your service engineer fi 5120C fi 5220C Image Scanner Getting Started 2 Chapter2 INSTALLATION OF THE SCANNER 2 1 Installing the Scanner ADF paper chute 1 Place the scanner at its installation site For details on the scanner s dimensions and required installation space refer to fi 5120C f1 5220C Operator s Guide 7 2 Installation Speci fications in the Setup CD ROM For fi 5120C go to Step 3 2 Unlock the Shipping lock The carrier unit inside the scanner is fixed in place by
25. ing starting position Adjust the Sub scan Setting on Scanners and Cameras in the control panel AP 2 W Temporary error Indication Meaning UO Shipping lock error fi 5220C U1 Paper feed error U2 Multi feed error U4 The ADF cover is opened U6 Print cartridge not installed fi 5120C To troubleshoot the indicated errors above UO error Confirm that the shipping lock is released U1 error Remove all jammed documents Confirm that the documents meet the paper con ditions for scanning Refer to fi 5 120C fi 5220C Operator s Guide 5 Troubleshooting on the Setup CD ROM U2 error Remove all jammed documents Confirm that the documents are within the required paper preconditions for scanning Refer to fi 5120C fi 5220C Operator s Guide 6 2 Document Quality on the Setup CD ROM U4 error Close the ADF cover completely For the details refer to 5 TROUBLESHOOTING in the fi 5120C fi 5220C Operator s Guide on the Setup CD ROM U6 error This is a temporary error related with the Imprinter option sold separately Refer to fi 512PR Operator s Guide 5 Error Message fi 5120C fi 5220C Image Scanner Getting Started MW Device alarm Non Temporary error Indication Meaning E0 Flatbed motor malfunction E1 Trouble in the optical system Flatbed E2 Trouble in the optical system front E3 Tro
26. l and detailed information on Operations when you would like to using advanced fea tures daily maintenance of the scanner replacement of consumables Please also read the Operator s Guide for your reference NW Regulatory Information FCC Declaration This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures eReorient or relocate the receiving antenna eIncrease the separation between the equipment and receiver eConmnect the equipment into an outlet on a circuit different from that to which the receiver is located eConsult your dealer or an experienced radio TV technician FCC warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to
27. lectric shock as well as injury Before moving the scanner be sure to disconnect the power plug from the power outlet and all other data cables Make sure that the floor is free of any obstructions Protect the scanner from static electricity Install the scanner away from strong magnetic fields and other sources of electronic noise Also protect the scanner against any static electricity which can cause the scanner to malfunction Do not use aerosol sprays near the scanner Do not use aerosol sprays to clean the scanner Aerosol sprays can blow dirt and dust inside the scanner resulting in scanner failure or malfunction Disconnect the power plug from the power outlet when the scanner is not used for a long period of time When the scanner is not going to be used for a long period of time be sure to disconnect the power plug from the power outlet for safety Do not install the scanner in the direct sunlight Do not install the scanner under direct sunlight or near heating apparatus Doing so might cause excessive heat to build up inside the scanner which can cause scanner trouble or even fire Install the scanner in a well ventilated location Before moving the scanner make sure the shipping lock is locked Q When moving the scanner be sure to lock the shipping lock in order to prevent damages to the scanner Be aware of the pick spring When you perform cleaning make sure tha
28. matically detected Found New Hardware Wizard or Add Remove Hardware Wizard dialog box will appear Click Cancel to close the Wizard window Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for f 5220Cdj If your hardware came with an installation CD 2 or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue 4 Insert the Setup CD ROM into the CD drive gt lt SETUP DISK START UP SCREEN gt appears HHRHHHHHHEHHHHHHHE EI an This screen may not appear when the Y case run Install exe in this CD ROM directly from the Explorer or My Computer Autoplay setting of your PC is off In this HHRHHHHHHHHHHHHEHE EI 5 Click INSTALL PRODUCTS and then click ISIS Driver gt lt SETUP DISK START UP SCREEN gt FUJITSU Image Scanner Setup README FIRST INSTALL PRODUCTS USER S GUIDE BROWSE cD All Right Reserved Copyright C PFU LIMITED 1995 2005 6 Error Recovery Guide Installation dialog box appears Error Recovery Guide is an application with which you can view on screen information for troubleshooting errors that may occur in the scanner This guide helps solve problems so select Yes to install it You may also choose to install it later HBHRHRHRHHHHEHHHEHEHEEHEH ESE
29. on as a user with Adminis ATTENTION D trator privileges HHRHRHHHHHHHHHEHEHE EE 1 Insert the Setup CD ROM into the CD drive gt lt SETUP DISK START UP SCREEN gt appears 2 Click INSTALL PRODUCTS and then click ScandAll PRO 3 Select a language for the installation on Choose Setup Language dialog box and then click the Next button 4 Proceed with the installation following the on screen instructions 5 When the InstallShield Wizard Complete dia log box appears click the Finish button ale For information about the features of Scan WN dAll PRO refer to Help topics in ScandAll GC PRO For FUJITSU ISIS Scanner Driver E Preparation Confirm the following items before installing the driver application e Take out the Setup CD ROM from its pack age but do not insert the Setup CD ROM into the CD driver yet e Connect the scanner correctly to your PC ale For details on how to connect the scanner refer to 2 2 Connecting the Scanner to Your PC on page 4 NW Installing the FUJITSU ISIS Scanner Driver rey 1 Press the power button to turn on the scanner Windows XP screenshots are used in this section as examples The windows and operations may vary slightly if your OS is other than Windows XP 2 Turn your PC on and log on to Windows asado Be sure to log on as a user with Administra N tor privileges HHRHHHHHHHHHHHEHEHE GI 3 If the scanner is auto
30. or power plugs or install any cables or power plugs to loose wall sockets Use only specified AC cables and connector cables Use only specified AC cables and connector cables Failure to use the correct cables might cause electric shock and or equipment failure Please don t use the AC cable provided with this scanner for other devices since this might cause equipment failure and other troubles or an electric shock Use this scanner only at the indicated power voltage Do not connect to multiple power strips Use this scanner only at the indicated power voltage and current Improper power voltage and current might cause fire or electric shock Do not connect to multiple power strips Do not touch the AC cable with wet hands Do not touch the power plug with wet hands Doing so might cause electric shock Wipe any dust from the power plug Q Wipe off any dust from metal parts on the power plug or metal fittings with a soft dry cloth Accumulated dust might cause fire or electric shock fi 5120C fi 5220C Image Scanner Getting Started Do not install the device in locations that has oil smoke steam humidity and dust Do not install the scanner in locations subject to oil smoke steam humidity and dust Doing so might cause a fire or electric shock Turn the scanner OFF if it is damaged If the scanner is damaged for any reason turn the scanner off and unplug the power cable Contact the
31. ows from Add Remove Programs of the control panel NW Installing the FUJITSU TWAIN32 Scanner Driver ate Windows XP screenshots are used in this sec 8 tion as examples The windows and opera tions may slightly vary if your OS is other than Windows XP 1 Press the power button to turn on the scanner 2 Turn on your PC and log on to Windows HBHRHRHHEHEHEHEHEHEHHHEHEHE GI eat Be sure to log on as a user with Administra wy tor privileges HBHHRHRHHEHEHEHHEHEHHEHEHE GI 3 If the scanner is automatically detected Found New Hardware Wizard or Add Remove Hardware Wizard dialog box will appear Click Cancel to close the Wizard win dow Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for fi 5220Cdj If your hardware came with an installation CD 2 or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue Co Cese 4 Insert the Setup CD ROM into the CD drive gt lt SETUP DISK START UP SCREEN gt appears HBHRHRHBRHHEHEHEHHEHHEHEHEHE GI This screen may not appear when the W Autoplay setting of your PC is off In this case run Install exe in this CD ROM directly from the Explorer or My Computer HHRHRHHHHHEHHHHHHEHE GI 5 Click INSTALL PRODUCTS and then click TWAIN Dri
32. plays the Add or remove Programs screen which displays a list of the currently installed applications Select the application to uninstall e When uninstalling FUJITSU TWAIN 32 scanner driver select Scanner Utility for Microsoft Win dows e When uninstalling ScandAll PRO select Fujitsu ScandAll PRO V1 5 e When uninstalling FUJITSU ISIS scanner driver select Fujitsu ISIS Drivers e When uninstalling QuickScan Pro select QuickScan e When uninstalling Error Recovery Guide select Error Recovery Guide e When uninstalling Software Operation Panel select Software Operation Panel TENN e When uninstalling Image Processing wy Software Option refer to Image Pro cessing Software Option Operation Guide e When uninstalling Adobe Acrobat refer to the installation procedure described in the Adobe Acrobat CD ROM 11 5 Click the Change Remove or Remove but ton 6 When the confirmation dialog box appears Click the OK or Yes button gt This executes the uninstallation NONE ARQ eer Screen displays may vary slightly accord yy ing to the operation system OS you are using Follow the on screen instructions of the OS Examples In Windows 2000 the window and button names described above are as follows e Add or Remove Programs gt Add Remove Applications e The Change Remove button gt The Add Remove button In Windows Vista the window and button names descri
33. rm Windows is used Adobe Acrobat Adobe Acrobat All the descriptions in this manual assume the usage of Adobe Acrobat bundled with this product However Adobe Acrobat may be upgraded without notice If the descriptions differ from the screens actually displayed refer to the Acrobat s Help Manufacturer PFU LIMITED International Sales Dept Imaging Business Division Products Group Solid Square East Tower 580 Horikawa cho Saiwai ku Kawasaki shi Kanagawa 212 8563 Japan Phone 81 44 540 4538 All Rights Reserved CopyrightO PFU LIMITED 2006 2009 About Maintenance The user must not perform repairs on this scanner Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to have repairs done on this product Warning Indications Used In This Manual ZAWARNING This indication alerts operators to an operation that if not strictly observed may result in severe injury or death This indication alerts operators to ZN CAUTION an operation that if not strictly observed may result in safety hazards to personnel or damage to equipment Symbols Used In This Manual aprenden This symbol alerts operators to particularly ay important information Be sure to read this information This symbol alerts operators to helpful A ne advice regarding operation A TRIANGLE symbol indicates that special care and attention is required The drawing in
34. s a software that displays troubleshooting information on screen if any scanner error occurs If you did not install the Error Recovery Guide when installing the scanner driver install it following the pro cedure below 1 Insert the Setup CD ROM into the CD drive gt lt SETUP DISK STARTUP SCREEN gt appears 2 Click INSTALL PRODUCTS 3 Click Error Recovery Guide on the next screen 4 Select a language to use for the installation in the lt Choose Setup Language gt window and click Next 5 Install the application following the instructions in the window 6 When the InstallShield Wizard Complete screen displays click Finish Image Processing Software Option Trial For details on the installation of the Image Processing Software Option refer to the Image Processing Soft ware Option USER S GUIDE Adobe Acrobat Install Adobe Acrobat from the Adobe Acrobat CD ROM provided with this scanner Adobe Acrobat is needed to display manu ale HINT als C You do not have to install Adobe Acrobat if it is already installed on your computer 1 Insert the Adobe Acrobat CD ROM into the CD ROM drive gt The Adobe Acrobat dialog box appears seamed This dialog box may not appear if the wy AutoPlay setting is set to off In this case find AutoPlay exe in the CD ROM using Windows Explorer or My Computer and launch it 2 Inthe dialog box below click the folder icon
35. side the triangle shows the specific caution The drawing inside or under the circle shows the specific action that is not allowed Outline characters on a colored background show instructions users should follow It may also include the drawing that shows the specific instruction A CIRCLE with a diagonal line inside S shows action which users may not perform Warning Label The glass surface inside the ADF becomes AN hot during the operation Be careful not to touch the glass surface inside the ADF HHHHHHHHEHEHEHHEHEHE EG m n Do NOT remove from the scanner stain or yy scratch the warning labels HHRHHHHHHHHEHEHEHEHE EGE Screen Examples In This Manual The screen examples in this manual are subject to change without notice in the interest of product improvement If the actual displayed screen differs from the screen examples in this manual operate by following the actual displayed screen while referring to the User s Manual of the scanner application you are using The screenshots in this manual were captured from FUJITSU TWAIN32 scanner driver ScandAll PRO Image Capturing Utility Software FUJITSU ISIS scanner driver QuickScan image capturing software and Adobe Acrobat E Safety Precautions Do not damage the AC cable A damaged AC cable may cause fire or electric shock Do not place heavy objects on AC cables or pull bend twist heat damage or modify AC cables Do not use damaged AC cables
36. t the inside of the scanner is free of any foreign object and be careful not to get your hand or the cloth caught on the pick spring metal part as a deformed pick spring metal part may cause injury fi 5120C fi 5220C Image Scanner Getting Started vii Chapter 1 1 Checking the Contents of the Scanner Package When you open the scanner package please handle the main unit and its attachments carefully Make sure it contains all the parts listed in the package contents list that is included in the package box If any parts are missing or defective contact the dealer you purchased the scanner or an authorized Fujitsu scan ner service provider Handle the scanner and accessories with care 1 2 Names and Functions of Parts This section describes the scanner parts and their func tions E Front fi 5120C ADF paper chute Side guide Automatic document feeder ADF ADF button Operator panel fi 5220C ADF paper chute Side guide ADF Automatic document feeder G ADF button Flatbed A L A Yj Operator panel Stacker PREPARING THE SCANNER MW Inside fi 5220C Shipping lock located on base MW Rear fi 5120C DC inlet BE SCSI ID switch Security Slot EXT connector For Imprinter SCSI Interface conne
37. the shipping lock to prevent the scanner from becoming damaged during transportation from the factory After transporting and placing the scanner tilt the scanner approx 30 degrees and release the 4 Connect the AC adapter Shipping lock on the bottom of the scanner e degrees Side guide Poa Use only the AC adapter provided by the yy manufacturer 1 Connect the AC cable to the AC adapter aod Release N gee 2 Connect the AC adapter connector to the scan ner s DC inlet 3 Attach the ADF paper chute Hold the ADF paper chute and insert its tabs into the corresponding slots in the scanner as shown in the next figure below The Side guides of the ADF paper chute have to face up 3 Plug the AC cable into the outlet The Function Number Display and the LED alo H may flash for an instant when plugging the C AC cable into the outlet 2 2 Connecting the Scanner to Your PC PETET This scanner is provided with two inter yy faces Ultra SCSI and USB 2 0 1 1 Con nect only one of the USB or SCSI interface cable NW Connecting with the USB Interface Cable 1 Connect the USB interface cable to the USB interface connector 2 Connect the other end of the USB interface cable to the PC pore e Be sure to use the USB cable which wy comes as an accessory with this scan ner Scanning operation with commercially available cables is not guaranteed e When
38. tive for Color Grayscale and or Monochrome under Compres sion in Acrobat and scanning in a reso lution lower than the resolution recommended for Acrobat Solution Set OPTION to something other than Adaptive under Compres sion 3 Scanning a document longer than the double letter 11x17 or A3 size when setting Overscan in the TWAIN driver the scan may fail Solution When scanning a double letter 11x17 or A3 size of document do not set Overscan in TWAIN driver As for detailed usage and information of Acrobat refer to Create a PDF file from a scanned document in Acrobat Help Support and User registration for Adobe products Refer to the technical support information stored in the Customer Support folder on Adobe Acrobat CD ROM Note that free person to person support is not available for this is bundled product fi 5120C fi 5220C Image Scanner Getting Started 10 Uninstalling Supplied Programs Follow the procedure below to uninstall supplied pro grams Windows XP screenshots are used in this sec ale a 8 tion as examples The windows and opera 1 tions may slightly vary if your OS is other than Windows XP Start up your PC HHRHHHHHHHEHHEHEHEH EH SE E feces Be sure to log on as a user with Adminis ayy trator privileges 2 3 Exit all currently running programs Select Control Panel Add or remove Pro grams from the Start menu gt gt This dis
39. uble in the optical system back E4 The motor s fuse has blown out E6 Trouble in the operator panel E7 Trouble occurred in the internal memory EEPROM E8 The SCSI interface fuse has blown out E9 An error in the image memory EA Trouble with the Imprinter Ec An alarm in the memory Ed Trouble with the SCSI interface control ler EF Trouble with the background switching mechanism When you encounter any alarm on the display turn the scanner off and on If the alarm is still displayed on the Function Number display contact the store where you purchased the scanner or an authorized FUJITSU scan ner service provider AP 3 Appendix2 DAILY CARE ZAWARNING gt gt e The glass surface inside the ADF becomes hot during the operation Before you clean inside the scanner turn off its power and unplug the AC adapter from the outlet Wait for at least 15 minutes Do not turn off the scanner when you clean the Feed roll ers e When you perform cleaning make sure that the inside of the scanner is free of any for eign object and be careful not to get your hand or the cloth caught on the pick spring metal part as a deformed pick spring metal part may cause injury NW Cleaning Materials E Cleaning Method The ADF must be cleaned with a lint free cloth moist ened with the Cleaner F1 ATTENTION Y lt may take long before the cleaner vaporizes if a large quantity is used
40. ver Scanner Utility for Microsoft Windows Setup InstallShield Wizard Complete gt lt SETUP DISK START UP SCREEN gt The setup installed Scanner Utility for Microsoft Windows in the computer normally Before using this program it is necessary to re start a computer FUJITSU Image Scanner Setup Yes want to restart my computer now No will restart my computer later README FIRST Please click Finish button and end an setup INSTALL PRODUCTS USER S GUIDE BROWSE cD i Your computer will be restarted and the scanner will be detected Do not remove the Setup CD ROM from the CD drive until your PC has completely restarted All Right Reserved Copyright C PFU LIMITED 1995 2005 6 Error Recovery Guide Installation window appears HHHHHHHHHHHHEHEHE SE amp ATTENTION Y Error Recovery Guide is a software that dis plays troubleshooting information on screen when any scanner error occurs and its installa tion is highly recommended However it can be installed later if you do not install it in this step When you select Yes for installing the Error Recovery Guide Choose Setup Language window appears Select a language and fol low the instructions on the window Error Recovery Guide will automatically finish fin ishing its installation Please wait until the installation of TWAIN driver automatically starts Depending on the operating system you MS y are using
Download Pdf Manuals
Related Search