Sony SNC
Contents
1. ATTENTION The electromagnetic fields at specific frequencies may influence the picture of the unit Before Use e If you find condensation when you open the package turn on the power after the condensation disappears Remove the static electricity before operation or when touching the camera Data and security e You should keep in mind that the images or audio you are monitoring may be protected by privacy and other legal rights and the responsibility for making sure you are complying with applicable laws is yours alone Access to the images and audio is protected only by a user name and the password you set up No further authentication is provided nor should you presume that any other protective filtering is done by the service Since the service is Internet based there is a risk that the image or audio you are monitoring can be viewed or used by a third party via the network SONY IS NOT RESPONSIBLE AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU OR ANYONE ELSE FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR EVEN SERVICE CANCELLATION THE SERVICE IS PROVIDED AS IS AND SONY DISCLAIMS AND EXCLUDES ALL WARRANTIES EXPRESS OR IMPLIED WITH RESPECT TO THE SERVICE INCLUDING BUT NOT LIMITED TO ANY OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR THAT IT WILL OPERATE ERROR FREE OR CONTINUOUSLY Always make a test recording and verify that it was recorded successfully SONY WILL NOT BE LIABLE FOR DAM2. Synchronization Minimum illumination Lens Focal length SNC CH120 ZB550 2 8 mm to 8 0 mm SNC CH220 2 8 mm to 6 0 mm SNC EB520 3 0 mm to 8 0 mm SNC CH120 ZB550 F1 2 to F1 9 SNC CH220 F1 3 to F1 9 SNC EB520 F1 0 to F1 65 View angle SNC CH120 ZB550 1280 x 1024 Vertical 76 2 to 27 2 Horizontal 96 5 to 33 9 SNC CH220 1920 x 1440 Vertical 74 2 to 35 2 Horizontal 101 2 to 47 0 SNC EB520 800 x 600 Vertical 70 2 to 27 7 Horizontal 89 2 to 34 6 SNC CH115 CH120 CH220 ZB550 300 mm SNC EB520 200 mm Maximum relative aperture Minimum object distance Interface LAN PoE 10BASE T 100BASE TX auto negotiation RJ 45 The PoE power supply feature is not available on SNC ZB550 I O port Sensor input x 1 make contact break contact Alarm output x 1 24V AC DC 1A mechanical relay outputs electrically isolated from the camera MONITOR out SNC CH115 CH120 CH220 EB520 Pin jack 1 0 Vp p 75 ohms unbalanced sync negative 1 0 Vp p 75 ohms unbalanced sync negative during video output SLOC port SNC ZB550 Others Power SNC CH115 CH120 CH220 EB520 IEEE802 3af compliant PoE system SNC ZB550 DC 12V AC 24V SNC CH115 CH120 CH220 EB520 5 0 W max SNC ZB550 6 0 W max Start temperature 0 C to 50 C 32 F to 122 F Working temperature 10 C to 50 C 14 F to Power consumption Operating temperature 122 F Storage temperature 20 C to 60 C 4 F to 140 F Operatin
3. The SNC ZB550 operates on 24V AC or 12 V DC The SNC ZB550 automatically detects the power Use a power supply rated 24 V AC or 12 V DC which meets the requirements for SELV Safety Extra Low Voltage and complies with Limited Power Source according to IEC 60950 1 CAUTION for LAN port For safety reason do not connect the LAN port to any network devices that might have excessive voltage CAUTION for LAN port SNC CH115 CH120 CH220 EB520 The LAN port of this unit is to be connected only to the devices whose power feeding meets the requirements for SELV Safety Extra Low Voltage and complies with Limited Power Source according to IEC 60950 1 Use IEEE802 3af standard compliant devices For customers in the U S A This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause ha
4. Connect to a network using a coaxial cable or LAN Connecting via a coaxial cable When the network connection change switch is set to SLOC connect to a network via a coaxial cable The maximum coaxial cable length is RG 59 300 m The high frequency characteristics of coaxial cables may differ even if the cables are of the same classification Use a high quality high frequency coaxial cable with this unit For details refer to the instruction manual of the connecting SLOC device For further details please consult an authorized Sony dealer When connecting with a coaxial cable do not connect a network cable to this unit Connecting via LAN When the network connection change switch is set to LAN use a network cable straight not supplied to connect this unit s LAN port to the network s router or hub Connecting to a computer Use a network cable crossover not supplied to connect this unit s LAN port to the computer s network connector Connecting to 12 V DC or 24 V AC source SNC ZB550 Connect the power input cable of the camera to a 12 V DC or 24 V AC source Use a 12V DC or 24V AC source isolated from 100 to 240 V AC The acceptable voltage ranges for each are as follows 12V DC 10 8 V to 13 2 V 24V AC 21 6 V to 26 4V In the USA The product shall be powered by a UL Listed Class 2 Power Supply Only In Canada The product shall be powered by a CSA certified Class 2 Power Supply Only
5. 2 3 2 1 3 145 5 3 140 5 5 3 145 6 5 3 4 Side SNC CH115 145 5 3 140 5 5 4 145 6 5 3 Side SNC EB520 42 8 1 1 16 145 5 3 4 140 5 5 4 43 13 4 i Ts r 55 2 145 6 5 3 Side SNC ZB550 52 2 1 3 43 1 3 4 55 274 145 5 3 140 5 5 4 150 5 6 Unit mm inch SNC ZB550 J oodi J 24 m O 7 POwER 1 0 i SEE Il STRUCTION NTSC SLOC DC 12V AC 24V LAN Network cable straight not supplied device Video output terminal Coaxial cable Video monitor etc 10BASE T 100BASE TX Network SLOC 4 connector Coaxial cable Coaxial cable maximum length RG 59 300 meters SLOC compatible LAN port RJ 45 Network cable 10BASE T 100BASE TX Network device Installation e If you attach the camera in a high location such as wall or ceiling etc entrust the installation to an experienced contractor or installer e If you install the camera in a high location ensure that the ceiling is strong enough to withstand the weight of t
6. 4 199 272 17 1 SONY Network Camera Installation Manual Before operating the unit please read this manual thoroughly and retain it for future reference SNC CH115 CH120 CH220 SNC EB520 ZB550 IAP ELA sloc Exmor http www sony net IPELA HYBRIB HD 4199272170 2010 Sony Corporation Printed in China Owner s Record The model and serial numbers are located on the top Record these numbers in the spaces provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No This Installation Manual gives instructions for multiple types of Network Cameras SNC CH115 CH120 CH220 are PoE type HD models SNC EB520 is a PoE type SD model and SNC ZB550 is an HD model IPELA HYBRID camera To reduce a risk of fire or electric shock do not expose this product to rain or moisture Serial No To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only WARNING This installation should be made by a qualified service person and should conform to all local codes Power Supply Caution for U S A and Canada SNC ZB550 The SNC ZB550 operates on 24V AC or 12 V DC The SNC ZB550 automatically detects the power In the USA this product shall be powered by a UL listed Class 2 Power Supply Only In Canada this product shall be powered by a CSA Certified Class 2 Power Supply Only Caution for other countries SNC ZB550
7. AGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE OF THIS UNIT OR ITS RECORDING MEDIA EXTERNAL STORAGE SYSTEMS OR ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE Always verify that the unit is operating properly before use SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT EITHER DURING THE WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY OR FOR ANY OTHER REASON WHATSOEVER If you lose data by using this unit SONY accepts no responsibility for restoration of the data Personal information The images taken by the system using this device can identify individuals and thus they fall under personal information stipulated in the Act on the Protection of Personal Information Please handle the video data appropriately according to law Information recorded using this product may also be personal information Upon disposal transfer repair or any other occasion where this product or storage media is passed on to a third party practice due care in its handling Operating or storage location Avoid operating or storing the camera in the following locations Extremely hot or cold places Operating temperature 10 C to 50 C 14 F to 122 F Exposed to direct sunlight for a long time or close to heating eq
8. Use UL cable VW 1 style 10368 for these connections recommended cable DC12V CABLE AWG 26 24 22 Max length m 8 12 21 AC24 V CABLE AWG 26 24 22 Max length m 32 50 85 Connecting the I O Cable Connect the wires of the I O cable as follows Wiring diagram for sensor input Mechanical switch open collector output device Camera inside Outside 3 3V 47 KQ 30 kQ Mechanical Sensor input switch Sensor input GND or Open collector GND GND output device Wiring diagram for alarm output Camera inside Outside 5V Alarm Output Magnet relay AC 24V DC 24V 1 Aorless Circuit example Alarm Output GND Specifications Compression Video compression format JPEG MPEG4 H 264 SNC CH115 CH120 ZB550 H 264 30 fps 1280 x 720 Maximum frame rate SNC CH220 H 264 30 fps 1920 x 1080 SNC EB520 H 264 30 fps 800 x 600 Camera Signal system NTSC color system PAL color system switchable Image device SNC CH115 CH120 EB520 ZB550 1 3type CMOS Exmor Effective picture elements Approx 1 390 000 SNC CH220 1 2 8type CMOS Exmor Effective picture elements Approx 3 270 000 Internal synchronization SNC CH120 ZB550 F1 2 AGC 42 dB 50 IRE IP Color 0 50 Ix Black amp White 0 30 Ix SNC CH220 F1 3 AGC 42 dB 50 IRE IP Color 0 70 Ix Black amp White 0 45 Ix SNC EB520 F1 0 AGC 42 dB 50 IRE IP Color 0 47 Ix Black amp White 0 27 Ix
9. enomena Specific to Image Sensors The following phenomena that may occur in images are specific to image sensors They do not indicate a malfunction White flecks Although the image sensors are produced with high precision technologies fine white flecks may be generated on the screen in rare cases caused by cosmic rays etc This is related to the principle of image sensors and is not a malfunction The white flecks especially tend to be seen in the following cases when operating at a high environmental temperature when you have raised the gain sensitivity when using the slow shutter Aliasing When fine patterns stripes or lines are shot they may appear jagged or flicker About the Supplied Manuals Installation Manual this document This Installation Manual describes the names and functions of parts and controls of the Network Camera gives connection examples and explains how to set up the camera Be sure to read the Installation Manual before operating The pictures of an SNC CH220 camera are used in the explanatory examples User s Guide stored in the CD ROM The User s Guide describes how to set up the camera and how to control the camera via a Web browser After installing and connecting the camera correctly operate referring to this User s Guide Using the CD ROM Manuals The supplied CD ROM disc includes the User s Guides for this unit in PDF format Preparations The Adobe Reader Version 6 0 or hi
10. g Turn this ring toward T for telephoto or toward W for wide angle Tripod screw hole Use this screw hole when attaching the camera to a tripod N U1 4 20 UNC 4 5 mm to 7 mm ISO standard with the screws fastened Use the mounting screw whose length is 4 5 mm 3 16 inch to 7 mm 32 inch only Use of other screws may cause improper mounting and damage parts inside the camera Rating Label This label shows the name of device and its electric rating O Lens connector 4 pin socket Supplies power and control signals to an auto iris lens Lens mount SNC CH115 only Use to mount an appropriate CS mount lens Use the C mount adaptor optional when you use the C mount lens A vari focal lens is mounted as the standard equipment for SNC CH120 CH220 EB520 ZB550 Rear E 1 0 Input Output port This cable is provided with a sensor input and an alarm output The wires of the cable control the following signals SNC CH115 CH120 CH220 EB520 PinNo Signal 1 Alarm output 1 2 Alarm output 1 3 Sensor input GND 4 Sensor input SNC ZB550 PinNo Signal 1 Sensor input 2 Sensor input GND 3 Alarm output 1 4 Alarm output 1 For details on each function and required settings see the User s Guide stored in the supplied CD ROM For the wiring see Connecting the I O cable LAN network port RJ 45 Use the network cable UTP cate
11. g humidity 20 to 80 Storage humidity 20 to 95 Dimensions w h d J SNC CH115 72mm x 63 mm x 145 mm 27 s inches x 2 1 2 inches x 5 3 4 inches not including the projecting parts and lens SNC CH120 ZB550 72mm x 63 mm x 197 mm 27 s inches x 2 1 2 inches x 7 7 s inches with lens not including the projecting parts SNC CH220 72 mm x 63 mm x 197 3 mm 27 s inches x 2 1 2 inches x 7 7 s inches with lens not including the projecting parts SNC EB520 72 mm x 63 mm x 187 8 mm 2 7 s inches x 2 42 inches x 7 12 inches with lens not including the projection parts Mass SNC CH115 Approx 490 g 1 Ib 1 3 oz without lens SNC CH120 CH220 ZB550 Approx 550 g 1 Ib 3 4 oz with lens SNC EB520 Approx 530 g 1 Ib 2 7 oz with lens CD ROM Users Guides and supplied programs 1 Wire rope 1 Screw M4 1 DC 12V AC 24V connector 1 SNC ZB550 Installation Manual this document 1 Supplied accessories Design and specifications are subject to change without notice Recommendation of Periodic Inspections In case using this device over an extended period of time please have it inspected periodically for safe use It may appear flawless but the components may have deteriorated over time which may cause a malfunction or accident For details please consult the store of purchase or an authorized Sony dealer Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the United States and or other countr
12. gher must be installed on your computer in order to use the guides stored in the CD ROM disc If Adobe Reader is not installed it may be downloaded from the following URL http www adobe com Reading the manual in the CD ROM 1 Insert the CD ROM in your CD ROM drive A cover page appears automatically in your Web browser If it does not appear automatically in the Web browser double click on the index htm file on the CD ROM Select and click on the manual that you want to read This opens the PDF file of the manual Clicking an item in the Table of Contents allows you jump to the relevant page The files may not be displayed properly depending on the version of Adobe Reader In this case install the latest version which you can download from the URL mentioned in Preparations above e If you have lost or damaged the CD ROM you can purchase replacement Contact your Sony service representative This product is equipped with a Smartphone viewer With Smartphone viewer you can display an image from a network camera pan tilt and zoom that camera on your smartphone For more details see Smartphone viewer User s Manual at the following URL http www sony net ipela snc Location and Function of Part Front Lens A vari focal lens is mounted as standard equipment Focus ring Turn this ring toward N near to focus on a closer object Turn it toward F or infinite to focus on a farther object Zoom rin
13. gory 5 for network communications and PoE power supply However the PoE power supply feature is not available on SNC ZB550 See Connect to the Network for connection PoE The acronym for Power over Ethernet IEEE 802 3af standard compliant devices Easy Focus button Press this button to automatically adjust the focus To load the default setting press and hold this button for 4 seconds Fall prevention wire rope mounting screw hole When installing the camera to the ceiling or the wall secure the supplied wire rope to this hole using the supplied screw NETWORK indicator Green Orange The indicator lights up or flashes when the camera is connected to the network The indicator is off when the camera is not connected to the network When 100BASE TX is connected the indicator turns green When 10BASE T is connected the indicator turns orange The indicator also turns green when SLOC IP coaxial transfer is selected Reset switch To reset the camera to the factory default settings turn on the power to the camera while holding down this switch with a pointed object POWER indicator Green When the power is supplied to the camera the camera starts checking the system If the system is normal this indicator lights up NTSC PAL switch Switching the video output MONITOR output jack Output the composite video signal from the camera Monitor out is used when you adjust the angle of view Be sure to set monitor o
14. he camera plus mounting brackets and screws and then install the camera securely If the ceiling is not strong enough the camera may fall and cause serious injury e To prevent the camera from falling make sure to attach the supplied wire rope e If you attach the camera to the ceiling check periodically at least once a year to ensure that the connection has not loosened If conditions warrant make this periodic check more frequently Suitable lens The lens must be a CS mount type and the protrusion behind the mounting surface must be 5 5 mm 7 22 inch or less Keep the lens mount cap on the camera when it is not attached the lens When you install it into a wall or a ceiling check that the wall or the ceiling is strong enough to hold the weight of the camera including the mounting bracket and install it without fail If not the camera falls down and causes a serious injury Also check if the mounting is not loosened at least once a year Make the checking interval short according to use condition Performance will depend on the installation environment and the lens itself For details contact your authorized Sony dealer Attaching the wire rope D When you install the camera on a ceiling or a high position be sure to attach the supplied wire rope to prevent the camera from falling Attach the wire rope to the screw hole on the rear of the camera as in the illustration Take care not to s
15. hort circuit the cable with the wire rope when you attach it 1 Secure the wire rope to the junction box on the ceiling Use a screw to match the screw hole of your junction box not supplied 2 Secure the wire rope to the wire rope mounting screw hole on the rear of the camera using the supplied screw Use the supplied screws to install the unit Using other screws may cause damage inside the unit Adjusting the Camera Coverage and Focus E 1 Loosen the zoom ring locking screw to adjust the camera shooting coverage Tighten the locking screw to fix the zoom Loosen the focus ring locking screw to adjust the focus Tighten the locking screw to fix the focus Press the Easy Focus button on the rear to automatically adjust the focus You may not achieve satisfactory focus with the Easy Focus button due to the shooting environment In this condition press and hold Easy Focus button for more than 4 seconds to return to the default flange back position Then adjust the focus following step 3 and 4 Connect to the Network UAWN SNC CH115 CH120 CH220 EB520 Connect the LAN connector of the camera to a PoE supported device such as a hub using the network cable straight not supplied The electrical power is supplied through the network cable For details refer to the instruction manuals of the PoE supported devices PoE The acronym for Power over Ethernet IEEE 802 3af standard compliant devices SNC ZB550
16. ies sloc is a trademark owned by the Intersil Corporation family of companies
17. rmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules For customers in Canada This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada For the customers in Europe The manufacturer of this product is Sony Corporation 1 7 1 Konan Minato ku Tokyo Japan The Authorized Representative for EMC and product safety is Sony Deutschland GmbH Hedelfinger Strasse 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents For the customers in Europe Australia and New Zealand WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures In the case that interference should occur consult your nearest authorized Sony service facility This apparatus shall not be used in the residential area
18. uipment e g near heaters e Close to sources of strong magnetism e Close to sources of powerful electromagnetic radiation such as radios or TV transmitters e Locations subject to strong vibration or shock e Humid or dusty locations e Locations exposed to rain e Locations under the influence of fluorescent light or reflection of a window Under an unsteady light The image will flicker Ventilation To prevent heat buildup do not block air circulation around the camera Power supply SNC CH115 CH120 CH220 EB520 The power of this model is supplied by network cable e Use the network cable UTP category 5 Damage to the network cable may result in fire or electric shock Transportation Always turn off the power when carrying When transporting the camera repack it as originally packed at the factory or in materials of equal quality Cleaning Use a blower to remove dust from the lens Use a soft dry cloth to clean the external surfaces of the camera Stubborn stains can be removed using a soft cloth dampened with a small quantity of detergent solution then wipe dry e Do not use volatile solvents such as alcohol benzene or thinners as they may damage the surface finishes Note on laser beams Laser beams may damage image sensors You are cautioned that the surface of image sensors should not be exposed to laser beam radiation in an environment where a laser beam device is used Ph
19. ut to on when you use it Set it to off and disconnect the video cable when you do not use it For details on system setting see the User s Guide Do not connect to the video cable until the POWER indicator lights up Be aware that the system performance may be influenced if monitor out is set to on Be sure to set it to off and disconnect the video cable when you do not use it DC 12 V CAC 24 V power input terminal Connect to a 12 V DC or 24 V AC power supply system Network connection change switch Use this switch to change between a network connection to a LAN network port RJ 45 and a network connection using a coaxial cable SLOC IP coaxial transfer video output port Use this port when connecting the unit to a network using a coaxial cable When using a composite signal set the network connection change switch to LAN Also use this port to output composite video signals from this unit A connection to compatible equipment is necessary when connecting to a network using a coaxial cable For connection details refer to the instruction manuals of the equipment on the receiving end The output analog image may not display correctly depending on the video format and image size settings The image may not display properly in the horizontal and or vertical plane The image may be reduced ground terminal This is a ground terminal for the chassis continued on the re
20. verse side SNC CH120 CH220 EB520 ZB550 SNC CH115 SNC CH115 CH120 CH220 EB520 CLASS 2 WIRING VO FOCUS 0 aa PoE SEE INSTRUCTION MANUAL MONITOR NETWORK PO ER Coy NTSC PAL SNC ZB550 WIRING as LAN l DC IN 1 AC 24V 2 LUDON Zon Apar LAN NS NET ORK POWER 1 0 oN LY SIE INSTFUCTION A MANUAL NS CS mount lens 5 5 7 32 or less TC Unit mm inch Screw supplied When Easy Focus button is pressed mark indicates the approximate focus position The number indicates the focus position SNC CH115 CH120 CH220 EB520 CLASS 2 WIRING yy FOCUS 1 0 E SEE INSTRUCTIOI MANUAL O MONITOR ie 0 NTSC PAL 10BASE T A 100BASE TX a hub PoE supported device such as Network cable straight not supplied Front SNC CH120 CH220 ZB550 72 27 s 63 2 1 3 Front SNC EB520 72 27 3 63 2 1 3 62 27 16 Front SNC CH115 72 2 7 3 63 2 1 3 Side SNC CH120 CH220 SNC CH120 52 2 1 s SNC CH220 5
Download Pdf Manuals
Related Search