Home

DS-380D Series User`s Manual

1. 9 CONTEC 20 DS 380D Series User s manual 4 Each Component Function Giga bit Ethernet LAN This product is equipped with 2 ports for giga bit Network type 1000BASE T 100BASE TX 10BASE T Transmission speed 1000M 100M 10M bps Max network path length 100m segment Controller Realtek 8111G Table 4 4 Giga bit Ethernet Connector 10BASE T 100BASE TX 1000BASE T TRDO x Tm RDO RX TRDHI N C TRDH2 LEDs for display of network statuses Right LED Link LED Normal connection Orange ON Operation Orange Blinking Left LED Operation LED 10M Off 100M Green 1000M Orange N CAUTION Becareful of the guaranteed operating temperature when using the 1000BASE T network type For details see Installation Requirements in chapter 3 When using this product in an environment with a temperature of 0 to 45 C set the network type to 100BASE TX or IOBASE T H you are using the Wake On LAN WOL function set the OS driver setting Wake on Magic Packet to Enabled Also enable WOL from the BIOS setup screen For details see EuP ErP Power Saving Controller under Advanced in chapter 5 CONTEC DS 380D Series User s manual 21 4 Each Component Function USB Ports USB 3 0 This product is equipped with 3 channels for USB 3 0 interface You have to configure the BIOS settings to use USB 3 0 For details on the BIOS settings see SB USB Configuration under S
2. CONTEC DS 380D Series User s manual 19 4 Each Component Function LED POWER ACCESS STATUS There are 2 LED in front of this product Table 4 2 Display Contents of LED POWER LED Indicates that this product is switched off Indicates that this product is switched on ACCESS LED ON Orange ndicates that the storage device 1s being accessed DC Power Input Connector DC IN To supply the power always use the power supply listed below Rated input voltage 12 24VDC Range of input voltage 10 8 26 4VDC Power capacity 12V 3 0A or more 24V 1 6A or more Table 4 3 DC Power Connector Connector type 9360 04P mfd by ALEX CI Pin No Signal name 1 GND 4 3 2 GND 3 12 24V 9 O Hu 4 12 24V Applicable connector on the connector side Housing 9357 04 mfd by ALEX or 5557 04R mfd by MOLEX Contact 4256T2 LF AWGI8 24 mfd by ALEX or 5556 AWGI18 24 mfd by MOLEX Rise time of power supply Voltage 12V Time Figure 4 3 Graph of Rise Time of Power Supply Power Switch POWER SW POWER SW is provided Line out Interface LINE OUT A line output connector is provided You can plug a headphone or amplifier integrated speakers into this connector MIC in Interface MIC IN A MIC input connector is provided You can plug a microphone to this connector for sound input
3. NCT6106D Super IO Configuration NCT6106D Super IO Chip NCT6106D Serial Port 0 Configuration Serial Port 1 Configuration Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 14 NCT6106D Super IO Configration The following sub items are available Serial Port x Configuration x 0 1 Set Parameters of Serial Ports User can Enable Disable the serial port and Select an optimal settings for the Super IO Device You cannot use Serial Port 1 CONTEC 42 DS 380D Series User s manual 5 BIOS Setup Serial Port x Configuration x 0 1 Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Serial Port x Configuration Serial Port Enabled Device Settings IOzXXXh IRQ X Change Settings Auto lt Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 15 Serial Port x Configuration x 0 1 The setting that can be configured on the Serial Port x Configuration x 0 1 screen is described in the table below Table 5 12 Serial Port x Configuration x 0 1 Serial Port Disabled Enable Disable Serial Port support
4. CONTEC 50 DS 380D Series User s manual 5 BIOS Setup Boot Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Chipset Security Save amp Exit Boot Configuration Setup Prompt Timeout 1 Bootup NumLock State On Quiet Boot Disabled Fast Boot Disabled CSM16 Module Version 07 69 GateA20 Active Upon Request Option ROM Messages Force BIOS Select Screen INT19 Trap Response Immediate 11 Select Item CSM Support Enabled Enter Select Change Opt Driver Option Priorities F1 General Help F2 Previous Values Boot Option Priorities F3 Optimized Defaults Boot Option x Device Name F4 Save amp Exit ESC Exit Hard Drive BBS Priorities CD DVD ROM Drive BBS Priorities gt CSM parameters Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 23 Boot Menu Specify the settings related to how the system will start The following items are available Table 5 16 Boot il 65535 Number of seconds to wait for setup activation key 65 65535 0xFFFF means indefinite waiting On Off Select the keyboard NumLock state Disabled 7 Enables Disables Quiet Boot option Enabled Enables Disables boot with initialization of a minimal set of Disabled Enabled devices required to launch active boot option Has no effect for IBBS boot options UPON REQUEST GA20 can be disabled using BIOS services Upon Request i A ia
5. N CAUTION Be careful to not forget the password If you forget the password the product will have to be repaired CONTEC DS 380D Series User s manual 55 5 BIOS Setup Save amp Exit Use this menu to load save settings changes and exit the setup menu Aptio Setup Utility Copyright C 20xx American Megatrends Inc Main Advanced Chipset Boot Security Save amp Exit Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults lt Select Screen Restore User Defaults 11 Select Item Enter Select Boot Override Change Opt SATA PM Device Name F1 General Help UEFI Device Name F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 27 Save amp Exit menu The following items are available Save Changes and Exit When you press Enter on this item you get a confirmation dialog box with a message similar to Save amp Exit Setup Save configuration and exit Select Yes to record the selections that you made on the menu to the FLASH ROM Depending on the changed items the system may restart The next time the computer is booted the BIOS configures the system based on the configuration stored in FLASH ROM Pressing No it will return to setup menu Discard Chan
6. WAYS do not allow disabling GA20 this option is useful when any RT code is executed above 1MB Force BIO Set display mode for Option ROM Options are Force BIOS and Keep Current Keep Current lmmediate S Enable Allows Option ROMs to trap Int 19 Postponed Disabled Enabled OpROM execution boot options filter etc Auto GateA20 Acti ate ctive Alae CONTEC DS 380D Series User s manual 51 5 BIOS Setup XXXXXXXXX Boot Option x E A Sets the system boot order Specify an arbitrary device Hard Drive BBS XXXXXXXXX MC 5 Sets the HDD boot order Priorites Specify an arbitrary device CD DVD ROM Drive XXXXXXXXX Se Ie GD DVD ROM DEVE EEN IBBS Priorities Specify an arbitrary device SE BEE A CAUTION In the Boot Option x list the same device may be displayed as shown below 1 USB Disk 2 UEFI USB Disk In this situation select 1 to perform legacy booting in which the disk is assumed to be MBR formatted and 2 to perform UEFI booting in which the disk is assumed to be GPT formatted Be sure to specify 1 for the boot setting Booting with option 2 is not supported Only the devices set with high priorities with the other settings such as CD DVD ROM Drive BBS Priorities can be selected in the Boot Option x lists CONTEC 52 DS 380D Series User s manual 5 BIOS Setup When Fast Boot is set to Enabled the settings become those shown in the following figu
7. 3 minutes at 25 C per month Power Management Power management setup via BIOS Power On by Ring Wake On LAN Supports ACPI Power management Power supply Rated input voltage 12 24VDC 6 Range of input voltage 10 8 26 4VDC 12V 6 5A Max 24V 3 3A Max External device power USB I F 5V 2 7A 900mA x 3 supply capacity Physical dimensions mm 218mm W x 140mm D x 35mm H No protrusions About 183kg 1 It may not be possible for the screen to be displayed correctly depending on the specifications of the connected display Also when the OS is Windows Embedded Standard 7 and a DVI display is connected although all the resolutions shown in this table can be set for the resolution setting of the OS use the product with a resolution that matches the specifications of the connected display 2 The disk capacities are values calculated with 1GB representing 1 billion bytes The capacity that can be recognized by the OS may be smaller than the actual capacity 9 CONTEC DS 380D Series User s manual T 2 System Reference 3 The storage that is installed varies depending on the OS model mSATA 8GB DS 380D DC7512 Windows Embedded Standard 7 32bit Japanese DS 380D DC7516 Windows Embedded Standard 7 32bit English DS 380D DC7517 Windows Embedded Standard 7 64bit Japanese DS 380D DC7518 Windows Embedded Standard 7 64bit English Half Slim SSD 32GB DS 380D DC741D Windows Embedded 8 1 Industry Pro 64bit Japane
8. On after Power failure Enable Schedule Slot 1 Power On Sunday Disable Monday Disabl Tuesday Disabl Wednesday Disabl Thursday Disabl Friday Disabl Saturday Disabl Select Screen PowerOn Hour 8 11 Select Item PowerOn Minute 0 Enter Select Schedule Slot 2 Power On Change Opt Sunday Disable F1 General Help Monday Disabl F2 Previous Values Tuesday Disabl F3 Optimized Defaults Wednesday Disabl F4 Save amp Exit Thursday Disabl ESC Exit Friday Disabl Saturday Disabl PowerOn Hour 8 PowerOn Minute 0 Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 11 iSmart Controller Screen with Schedule Slot Set to Power On The settings that can be configured when Schedule Slot is set to Power On are described in the table below Table 5 9 iSmart Controller Screen with Schedule Slot Set to Power On Item Options Description Sunday Monday Tuesday Wednesday Disable Thursday Friday Saturday Enable Hour 18 P On H Minut 5 m owerOn Hour Minute Minute fo CONTEC DS 380D Series User s manual 39 5 BIOS Setup When Schedule Slot is set to Power On Off the settings become those shown in the following figure Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced iSmart Controller Power On after Power failure Enable Schedule Slot 1 Power On Off Sunday Disable Monday Disable Tuesday Disabl
9. Precautions A DANGER Do not use the included AC adapter or the included AC power cable in combination with the AC adapter or AC power cable of another product Do not use the included AC adapter and AC power cable with any products other than this product Do not disassemble or modify the product or replace any of its parts Doing so may lead to electric shock fire or product failures ln addition CONTEC may not be able to provide servicing for the product if you modify it Do not attempt to replace the battery as inappropriate battery replacement poses a risk of explosion A WARNING Always check that the power supply is turned off before connecting or disconnecting power cables This product is not intended for use in aerospace space nuclear power medical equipment or other applications that require a very high level of reliability Do not use the product in such applications If using this product in applications where safety is critical such as in railways automotive or disaster prevention or security systems please contact your retailer CONTEC DS 380D Series User s manual CONTEC N CAUTION 1 Introduction Do not use or store this product in a location exposed to high or low temperature that exceeds range of specification or susceptible to rapid temperature changes Example Exposure to direct sun n the vicinity of a heat source Do not use this product in ex
10. ROM until you save it Pressing No it will return to setup menu Boot Override Using the cursor to select the device that you want to start and pressing Enter key directly boots the selected device regardless of the order set in the Boot menu CONTEC 58 DS 380D Series User s manual 6 Appendix 6 Appendix Battery Battery Specification This product uses the following battery Type Lithium primary battery Model ER 1 2AA Maker VARTA Nominal voltage 3 6V Nominal capacity 1200mAh Lithium content 1g or less Removing the Battery When Disposing of the Product Before disposing of the product follow the instructions given below to remove the battery 1 Remove the nine countersunk head screws Front six screws Back three screws upper surface only Figure 6 1 Removing the battery 1 2 Remove the heat sink and the case Figure 6 2 Removing the battery 2 CONTEC DS 380D Series User s manual 59 6 Appendix 3 Remove the battery Figure 6 3 Removing the battery 3 Disposing the battery Dispose the removed battery properly as instructed by local government 60 CONTEC DS 380D Series User s manual 7 List of Options 7 List of Options AC adapter PWA 84AWDI AC adapter Input 100 240V AC Output 12VDC 7A N CAUTION When using the product to match this AC adapter ensure that the current consumption with USB 5VDC is 2 7A or less in
11. SATA IDE Combined Mode Enabled Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 19 SB SATA Configuration The setting that can be configured on the SB SATA Configuration screen is described in the table below Table 5 14 SB SATA Configuration Disabled OnChip SATA Channel Enabled or Disabled 7 Native IDE Native IDE n RAID n AHCI n AHCI n Legacyl OnChip SATA Type I yperFlash i mode DE n IDE gt AHCI n H Legacy mode OnChip IDE mode gt Legacy mode or Native Native mode SATA IDE Combined Mode Disabled Enabled or Disabled 9 CONTEC DS 380D Series User s manual 47 5 BIOS Setup SB USB Configuration Aptio Setup Utility Copyright C 20xx American Megatrends Inc Chipset XHCI Controller 0 Disabled XHCI Controller 1 Disabled Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 20 SB USB Configuration The setting that can be configured on the SB USB Configuration screen is described in the table below If you will use USB 3 0 enable the following item Table 5 15 Item Displayed on the SB USB
12. The setting that can be configured on the Shutdown Temperature Configuration screen is described in the table below Table 5 7 Shutdown Temperature Configuration Disabled 70 C 158 F 75 C 167 F ACPI Shutdown 80 C 176 F 85 C 185 F 90 C 194 F 95 C 203 F 100 C 212 F The default setting is Disabled CONTEC DS 380D Series User s manual 37 5 BIOS Setup iSmart Controller Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced iSmart Controller Power On after Power failure Enable Schedule Slot 1 None Schedule Slot 2 None Select Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 10 Smart Controller The setting that can be configured on the iSmart Controller screen is described in the table below Table 5 8 iSmart Controller Item Options Description Power On after Power failure Disable Enable or Disable Enable None Schedule Slot Power On Setup the hour minute for system power on Power On Off CONTEC 38 DS 380D Series User s manual 5 BIOS Setup When Schedule Slot is set to Power Onl the settings become those shown in the following figure Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced iSmart Controller Power
13. Washer The altachment filings prevention filing prevention fing assembled sew assembled screw AC Adapter set PWA BAAWDT1 base angie M3x 8 M3x 6 Product IPC Warranty Royalty Setup quide Precaution Certificate consent Procedure List Coe contract Document CE M M Serial number Royalty consent Setup Procedure Produd quide IPC Precaution List Waray Ceiiicale Recovery Meda Label contract Document See the Product Configuration List to check if all the components are included for the specified number of units Copyright Copyright 2014 CONTEC CO LTD All Rights Reserved No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD CONTEC CO LTD makes no commitment to update or keep current the information contained in this document The information in this document is subject to change without notice All relevant issues have been considered in the preparation of this document Should you notice an omission or any questionable item in this document please feel free to notify CONTEC CO LTD Regardless of the foregoing statement CONTEC assumes no responsibility for any errors that may appear in this document or for results obtained by the user as a result of using this product Trademarks AMD ATI and AMD Corporation are registered trademarks of Intel Corporation Microsoft Windows are trademarks of Microsoft Corporation AMI are trademarks of AMI
14. erla or Enabledl nable 1sable seria ort support Auto IO 3F8h IRQ 4 10 3F8h IRQ 3 4 5 6 7 10 11 12 5 Change Settings The default setting is Auto 10 2F8h IRQ 3 4 5 6 7 10 11 12 10 3E8h IRQ 3 4 5 6 7 10 11 12 7 10 2E8h IRQ 3 4 5 6 7 10 11 12 CONTEC DS 380D Series User s manual 43 5 BIOS Setup NCT6106D HW Monitor View the system status such as the CPU and system temperatures and the input voltage Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Pc Health Status CPU Smart Fan Function 50 SYS Temp CPU Temp VCORE 45V 412V 41 5V YYYYYY lt lt lt lt e Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 16 NCT6106D HW Monitor The setting that can be configured on the NCT6106D HW Monitor screen is described in the table below Table 5 13 Item Displayed on the NCT6106D HW Monitor Menu Options Disabled pol 60 CPU Smart Fan Function 70 This function is not supported by this product 80 90 CONTEC 44 DS 380D Series User s manual 5 BIOS Setup Chipset Use this menu to specify advanced chipset settings Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Chipset Security Save amp Exit South Brid
15. repair return the device freight prepaid with a copy of the original invoice Please obtain a Return Merchandise Authorization number RMA from the CONTEC group office where you purchased before returning any product No product will be accepted by CONTEC group without the RMA number Liability The obligation of the warrantor is solely to repair or replace the product In no event will the warrantor be liable for any incidental or consequential damages due to such defect or consequences that arise from inexperienced usage misuse or malfunction of this device Safety Precautions Understand the following definitions and precautions to use the product safely CONTEC DS 380D Series User s manual 3 1 Introduction Safety Information This document provides safety information using the following symbols to prevent accidents resulting in injury or death and the destruction of equipment and resources Understand the meanings of these labels to operate the equipment safely DANGER indicates an imminently hazardous situation which if not avoided will ZA DANGER result in death or serious injury WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or in property damage Caution on the DS 380D Series Handling
16. total for the three ports RS 232C D sub 9pin conversion cable IPC RJ50 9F 020 RJ 50 10pin D sub 9pin conversion cable A CAUTION Precautions when using options not made by CONTEC When you use options not made by CONTEC the product may not operate correctly and there may be limits on the product s functions For more information on this options see the Contec s website 9 CONTEC DS 380D Series User s manual 61 DS 380D Series User s Manual DS 380D DC741D DS 380D DC741E DS 380D DC7512 DS 380D DC7516 DS 380D DC7517 DS 380D DC7518 CONTEC CO LTD May 2015 Edition 3 9 31 Himesato Nishiyodogawa ku Osaka 555 0025 Japan Japanese http Www contec co jp English http www contec com Chinese http www contec com cn No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO LTD 08042014 Management No NA03535 05082015_rev4 Parts No LYRS714
17. ts 19 LED POWER ACCESS STATUS nsutimenetaeni e ERR HEFT 20 9 CONTEC DS 380D Series User s manual iii DC Power Input Connector DC IN ses 20 Power Switch POWER SW ten nn Nu ete 20 Line out Interface LINE OUT e ka tne D Eee ROO ER yaa ee erneut in 20 MIC in Interface MIC INC iiie annee na EEN 20 Giga bit Bthemet 5 LAN sase sas iere rene HESPERIA SNR CUIRE Eee salsa ee ERE Ee adana 21 USB Ports USB 3 0 22 S rial Port Interface SERLTAL nonen nn cerne e ey Sai ai 22 DVEInt rface z DV ER eese teet ene nan en ERREUR RU ERH ERN dead aa 23 9 BIOS SETUP 25 og le 25 Stare ee 25 Using Setup o r tnt ren te non 26 Getting Help sine p PERDRE ERN BU RE iy IEEE 26 In Case of Problems 5 nte nere irte RR CREER EB sayanlar ERES EINER SERE akaya EE 26 A Final Note TE E 26 Main Men oso oe d e ESA Ee 27 Ni nnHlon de 27 ENEE 28 Advanced i E EE Ie EET ERES USES enr olsam et en IN een saanen allen ekin PCI Subsystem Setting issvscesssassvecsscvssevavasssscdenastaveieaseccassaneacasvsvcsssisascinsaxavscsvaviscsatesscoraasavesbeseates ACPI Setin re gecesi er nn nn OE AE EAE en ne ln nn tte o uenia ici E Node 0 Information octies e eR a EuP ErP Power Saving Controller ss IDE Configuration ect rre ao oe e RH enge ae ete Rd Shutdown Temperature Configuration iS mart Controller eec nn nn tee RYE Eee e REN ln ne ue USB Configurations I ONE UR REN rate com da NCT6106D Super IO Configuration Serial Po
18. 00BASE T 0 40 C 6 Figure 3 5 Installation Orientation DS 380D DCxxxx N CAUTION Note that even though the ambient temperature is within the specified range an operational malfunction may occur if there is other device generating high heat the radiation will influence the product to increase its temperature 9 CONTEC DS 380D Series User s manual 15 3 Hardware Setup Distances between this product and its vicinity or more Figure 3 6 A CAUTION Ee ES SSAA AE ENR SS Sa SSAA AAA Annan na nay goss Zeene GEERT a a a e al a a a a idid a al a a a a a a d dis a a L aad i RO or more MM RR R_RPRPRPEC g 9 p I LAL LLL a aae a a La aa CO E SN j A Ragga SS VEZ YA AL LL LL LL LL a LL LL LAS LS LN LL LIL LL thts LL LL Distances between this product and its vicinity SS G 7777 77 ALL LA e PE SS SSS SSSA AMAA AAA RANA SAI Da GR N SS Gees td Do not install this product into the fully sealed space except the case in which the internal temperature is adjustable by equipment such as air conditioner Troubles such as operational malfunctions could be occurred by the temperature increase caused by long term usage 16 CONTEC DS 380D Series User s manual 3 Hardware Setup Operating temperature In this product the operating temperature is decided from the multiple mea
19. Configuration Menu Disabled Enable or Disable USB3 0 XHCD XHCI Controller Enabled Controller support CONTEC 48 DS 380D Series User s manual 5 BIOS Setup North Bridge Configure the North Bridge chipset Aptio Setup Utility Copyright C 20xx American Megatrends Inc Chipset North Bridge Configuration Memory Information Total Memory XXXX MB DDR3 Socket 0 Information lt Select Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 21 North Bridge The setting that can be selected on the North Bridge screen is described below The following sub items are available Socket 0 Information Use this menu to view the memory information CONTEC DS 380D Series User s manual 49 5 BIOS Setup Socket 0 Information Aptio Setup Utility Copyright C 20xx American Megatrends Inc Chipset Socket 0 Information Starting Address X KB End Address XXXXXXX KB Dimm0 size 2048 MB speed 800 MHz Dimm1 size 2048 MB speed 800 MHz e Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 22 Socket 0 Information
20. D signal of the DC power connector DC IN Note that the connection cannot be cut off Screw holes may be damaged if screws are tightened with a torque greater than the specified torque The specified tightening torque is 5 6kgf cm CONTEC DS 380D Series User s manual 12 3 Hardware Setup Fastening the Cable This product comes with clamps for fixing cables Fastening the USB Cable With this product you can prevent disconnections of USB connectors that are not equipped with locking mechanisms by using the cable clamp Use the cable clamp by matching it to the connection status and wiring directions of the cables Use the clamp to fix the connectors in place so that stress is not applied to them Attached screw M3 x 6 M3 x 8 Figure 3 3 Attaching the cable clamp CONTEC DS 380D Series User s manual 13 3 Hardware Setup Installation Methods Use screws to attach the attachment fittings to the installation surface Do not apply excessive force when tightening the screws Figure 3 4 Installation Methods CONTEC 14 DS 380D Series User s manual 3 Hardware Setup Installation Requirements Be sure that the operating temperature is within the range specified in the installation environment requirement by making space between the product and device that generates heat or exhaust air DS 380D DCxxxx Installable directions at operating temperature 0 45 C When using 10
21. DS 380D Series Fanless R 452L mSATA Half Slim SSD DC input User s Manual CONTEC CO LTD Check Your Package Thank you for purchasing the CONTEC product The product consists of the items listed below Check with the following list that your package is complete If you discover damaged or missing items contact your retailer Product Configuration List DS 380D DC741D DS 330D DCT41H DS 380D DC7512 DS 380D DC7516 DS 380D DC7517 DS 380D DC7518 The main body c attachment HINES USB removal prevention Witting base USB removal prevention fitting 3 angle Washer assembled screw TME x 8 D Po Setup Procedure Document 1 ery Media Z AC adapter set PWA 84AWD1 3 Dust cover complete set fT 21 2 Audio Dust Cover 9 1 1 Itis attached to the main body 2 Please confirm latest information on the CONTEC homepage 3 The PWA 84AWD1 optional product is included in the package For details see the PWA 84AWD1 user s manual which can be downloaded from the CONTEC website Do not use the PWA 84AWD1 with any products other than this product Only use the included AC power cable with the included AC adapter CONTEC DS 380D Series User s manual Product Configuration Image DS 3800 Power connector Contact USB Dust Cover Audio Dust Cover COM Dust Cover LAN Dust Cover DVI Dust Cover a BA g M USB removal USB removal Washer
22. Enter on this item you get a confirmation dialog box with a message similar to Load Previos Values Load Previous Values No Pressing Yes discards any changes made and takes you back to the setup menu after loading the previous settings saved in FLASH ROM Pressing No it will return to setup menu Restore Defaults When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load Optimized Defaults Load Optimized Defaults No Select Yes to load the default values of the factory settings to use in operating the system This setting will not take effect until you save to FLASH ROM Pressing No returns to the setup menu without loading CONTEC DS 380D Series User s manual 57 5 BIOS Setup Save as User Defaults When you press Enter on this item you get a confirmation dialog box with a message similar to Save Values as User Defaults Save Configuration Pressing Yes saves the current settings as the user default settings in FLASH ROM and takes you back to the setup menu Pressing No it will return to setup menu Restore User Defaults When you press Enter on this item you get a confirmation dialog box with a message similar to Restore User Defaults Restore User Defaults Pressing Yes loads the settings saved in FLASH ROM as the user default settings and takes you back to the setup menu This setting is not reflected to the FLASH
23. Software International Inc Other brand and product names are trademarks of their respective holder CONTEC ii DS 380D Series User s manual Table of Contents Ch ck yout packa g s TR ea e ene vea A nr Nate i Copyright M ii E E CI ii Table of Contents sissies iranere SEENE A a E I E r a iii 1 INTRODUCTION 1 Aboutthe Product EE 1 RE La Vin e e e e e AEI EE ere ones 1 Supported OS EE 2 Customer Support kla 3 Web Site E Limited One Year Warranty 3 How to Obtain Service 3 Liability 23 Safety Precautions 3 Safety Information 4 CautionontheDS 380DSeries e 4 2 SYSTEM REFERENCE 7 Specification uec C RO I RAE A RR AE ae a a es 7 Power Management Features rro nocere e EDD ENEE oraya ya da ERR ETE ARR 9 Pow r Re E 9 Power Consutf ptiol NO mia 9 Physical Dimensions Re AR oet teen RERO RR RN Ee enisi p Pets e denke 10 3 HARDWARE SETUP 11 Before Using the Product for the First Time 11 Hardware Setup eer E n a RE a 12 Attaching the Attachment Fittings ses 12 tt the PG mI 12 Fastening the EE 13 Installation Methods 3 2 eet ya cete e RE COEUR GERM Gb tet e e d 14 Installation Requirements edocet erro tte eren xe e eee ene ede Eed 15 4 EACH COMPONENT FUNCTION 19 Component Name s roe ege 19 System ConfigufatiOt ei oe eere esamesi ER EE ns near
24. and is equipped with a 1 60GHz R 452L AMD Embedded APU It supports applications which require high speed processing Discrete GPU quality graphic processing This product has APU that is equipped with GPU AMD Radeon HD 7600G that features discrete GPU quality It supports DirectX 11 and OpenCL M1 1 9 CONTEC DS 380D Series User s manual 1 1 Introduction Fanless slitless design that reduces maintenance work This product has a completely spindleless design in which the CPU fan has been eliminated and mSATA and Half Slim SSD drives have been used for storage This eliminates concerns about the ingress of dust and other foreign matter into the product By minimizing the use of parts that degrade over time we have greatly reduced the cost of maintenance and inspection Remote power management function to reduce operation tasks This product supports timed automated system start up iSmart For example it enables unattended operation such as starting to show information of an establishment in unison at opening time Also it supports system start up externally via network Wake On LAN It encourages significant labor saving in operation Major types of peripherals are supported with rich interfaces It has a variety of extended interface such as DVI I x 2 1000BASE T x 2 USB3 0 x 3 and serial This makes it possible to use this product in a variety of situations Falling off prevention tools and fixing clamps provided to
25. ations not expressly approved the manufacturer can void the user s authority to operate this equipment CONTEC 6 DS 380D Series User s manual 2 System Reference 2 System Reference Specification Table 2 1 Functional Specification DETS DC AMD R Series Quad Core APU RD LOGH AMD ATOM Controller Hub BIOS BIOS mfd by AMD Memory 4GB 2GB x 2 204pin SO DIMM socket x 2 PC3 12800 DDR3 SDRAM AMD Radeon HD 76006 Video RAM Display I F DVI I I F x 2 29 pin connector x 2 System resolution 1 DVI 800 x 600 1024 x 600 1024 x 768 1280 x 720 1280 x 768 1280 x 1024 1360 x 768 1366 x 768 1400 x 1050 1440 x 900 1600 x 900 1680 x 1050 1920 x 1080 60Hz 16 770 000 colors Audio HD Audio compliant LINE OUT 63 5 Stereo mini jack Full scale output level 1 15Vrms Typ MIC IN 3 5 Stereo mini jack Full scale input level 1 4Vrms Typ 1 slot mSATA 8GB 2 is finished mounting bootable 3 1 slot Half Slim SSD 32GB 2 is finished mounting bootable 3 Serial I F RS 232C general purpose Ich SERIAL PORT 10pin RJ 50 connector pe CE j RJ 45 connector x 2 Wake On LAN support aug cm GER General purpose IO Hardware monitoring Monitoring CPU temperature board temperature power voltage Watch dog timer Software programmable 255 level 1sec 255 sec Causes a reset upon time out RTC CMOS Lithium backup battery life 10 years or more The real time clock is accurate within
26. avoid trouble caused by disconnected cable The USB removal prevention fitting and cable clamp enable you to prevent disconnections of USB cables and other connectors that are not equipped with locking mechanisms which enables you to prevent problems from occurring Models available with Windows Embedded 8 1 Industry Pro and Windows Embedded Standard 7 installed For Windows Embedded Standard installed model it is possible to use the EWF 1 function of OS It is designed for safety required for embedding purpose for example prohibiting unwanted writing to the mSATA or Half Slim SSD with EWF function will relieve the concern about the writing limits to the mSATA or Half Slim SSD and prevent an unintentional system alteration EWF Enhanced Write Filter is a function specific to Windows Embedded Standard that protects the disk from being actually written by redirecting the writing to RAM A wide range of power supplies 10 8 26 4 VDC supported As the product supports a wide range of power 10 8 26 4VDC it can be used in a variety of power environments The separately available AC adapter adds support for 100VAC power Supported OS Windows Embedded 8 1 Industry Pro 64bit Japanese English Windows Embedded Standard 7 32bit 64bit Japanese English CONTEC 2 DS 380D Series User s manual 1 Introduction Customer Support CONTEC provides the following support services for you to use CONTEC products more effic
27. ble of necessary external devices such as keyboard and a display to this product using appropriate cables STEP3 Turn on the power After verifying that you have correctly followed steps 1 and 2 turn on the power If you find any abnormality after turning on the power turn it off and check to see if the setup has been performed properly STEP4 Set up BIOS By referring to Chapter 5 set up BIOS This setup requires a keyboard and a monitor Before using this product be sure to execute Restore Defaults to initialize the BIOS settings to their default values See Chapter 5 Save amp Exit N CAUTION Be sure to connect the keyboard and mouse to it before turning the power on for the first time CONTEC DS 380D Series User s manual 11 3 Hardware Setup Hardware Setup Before you start be sure that the power is turned off Remove only those screws that are explained Do not move any other screw Attaching the Attachment Fittings 1 Use screws to attach the bundled attachment fittings with a screw The attachment fittings are attached to the product when it is shipped Do not tighten screws with excess force Attached screw M3 Figure 3 1 Attaching the Attachment Fittings Attaching the FG Use screws to attach the FG The screw is attached to the product when it is shipped Attached screw M3 Figure3 2 Attaching the FG N CAUTION The FG pin of this product is connected to the GN
28. e Wednesday Disable Thursday Disable Friday Disable Saturday Disable Select Screen PowerOn Hour 8 11 Select Item PowerOn Minute 0 Enter Select PowerOff Hour 21 Change Opt PowerOff Minute 0 F1 General Help Schedule Slot 2 Power On Off F2 Previous Values Sunday Disable F3 Optimized Defaults Monday Disable F4 Save amp Exit Tuesday Disable ESC Exit Wednesday Disable Thursday Disable Friday Disable Saturday Disable PowerOn Hour 8 PowerOn Minute 0 PowerOff Hour 21 PowerOff Minute 0 Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 12 iSmart Controller Screen with Schedule Slot Set to Power On Off The settings that can be configured when Schedule Slot is set to Power On Off are described in the table below Table 5 10 Smart Controller Screen with Schedule Slot Set to Power On Off DUET Sunday Monday Tuesday Wednesday Thursday Friday Saturday CONTEC 40 DS 380D Series User s manual 5 BIOS Setup USB Configuration Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced USB Configuration USB Devices X Drive X Keyboard X Mouse Legacy USB Support Enabled XHCI Hand off Enabled EHCI Hand off Enabled USB hardware delays and time outs USB transfer time out 20 sec lt Select Screen Device reset time out 20 sec 11 Select Item Device power up delay Auto Enter Se
29. e configured on the EuP ErP Power Saving Controller screen is described in the table below Table 5 6 EuP ErP Power Saving Controller Keep standby power Enable All of the standby power and ignore Keep standby power EuP ErP specification EuP ErP standby power control Ethernet Only WOL Ethernet Only No standby power Only provide the standby power for Ethernet chip No standby power Shut down all of the standby power 9 CONTEC DS 380D Series User s manual 35 5 BIOS Setup IDE Configuration IDE Configuration SATA Porto SATA Port1 Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Not Present Not Present Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Figure 5 8 IDE Configuration Version x xx xxxx Copyright C 20xx American Megatrends Inc 36 CONTEC DS 380D Series User s manual 5 BIOS Setup Shutdown Temperature Configuration Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced ACPI Shutdown Temperature Disabled e Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 9 Shutdown Temperature Configuration
30. ect use the and keys to change entries press F1 for help and press Esc to quit The following table provides more detail about how to navigate in the Setup program using the keyboard Table 5 1 Using Setup Key Function Let Arrow Submenus Exit Current page to the next higher level menu key Decrease the numeric value or make changes F1 key General help on Setup navigation keys F2 key Load previous settings Load the optimized defaults Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item To exit the Help Window press lt Esc gt or the F1 key again In Case of Problems If it is not possible to boot the computer after system settings have been changed and saved during setup this product will need to be repaired The best advice is to only alter settings which you thoroughly understand To this end we strongly recommend that you avoid making any changes to the CPU chipset defaults These defaults have been carefully chosen by both AMI and your systems manufacturer to provide the absolute maximum performance and reliability If chipset settings are changed even slightly it may become necessary to repair the unit A Final Note About Setup The information in this chapter is subject to change without notice CONTEC 26 DS 380D Series User s manual 5 BIOS Setup Main Menu Once you enter
31. eep Vibration resistance resistance Grounding CONTEC 8 DS 380D Series User s manual 2 System Reference Power Management Features Support ACPI Advanced Configuration and Power Interface Power Requirements Your system requires a clean steady power source for reliable performance of the high frequency CPU on the product the quality of the power supply is even more important For the best performance makes sure your power supply provides a range of 12 V minimum to 24 V maximum DC power source Power Consumption For typical configurations the CPU card is designed to operate with at least a 84W power supply The power supply must meet the following requirements Rise time for power supply 2 ms 30 ms The following table lists the power supply s tolerances for DC voltages Table 2 3 DC voltage tolerance DC Voltage Acceptable Tolerance 12V 24V 10 8 26 4VDC CONTEC DS 380D Series User s manual 9 2 System Reference Physical Dimensions DS 380D DCxxxx Attached screw M3 Figure 2 1 DS 380D DCxxxx CONTEC 10 DS 380D Series User s manual 3 Hardware Setup 3 Hardware Setup Before Using the Product for the First Time Follow the next steps to set up this product STEPI By referring to the information in this chapter install connect and set this product STEP2 Connect cables Connect the ca
32. ent from ones of our industrial products IPC Series BOX PC PT Series and others For details please consult our retailer This product is available in the following 6 models Windows Embedded 8 1 Industry Pro 64bit Japanese version installed model DS 380D DC741D Memory 4GB mSATA 8GB Half Slim SSD 32GB 1 Windows Embedded 8 1 Industry Pro 64bit English version installed model DS 380D DC741E Memory 4GB mSATA 8GB Half Slim SSD 32GB 1 Windows Embedded Standard 7 32bit Japanese version installed model DS 380D DC7512 Memory 4GB mSATA 8GB Half Slim SSD 32GB 2 Windows Embedded Standard 7 32bit English version installed model DS 380D DC7516 Memory 4GB mSATA 8GB Half Slim SSD 32GB 2 Windows Embedded Standard 7 64bit Japanese version installed model DS 380D DC7517 Memory 4GB mSATA 8GB Half Slim SSD 32GB 2 Windows Embedded Standard 7 64bit English version installed model DS 380D DC7518 Memory 4GB mSATA 8GB Half Slim SSD 32GB 2 The OS is installed on the Half Slim SSD drive 2 The OS is installed on the mSATA Features Equipped with DVI output to support high definition video This product is standard equipped with two DVI output ports that support displays of 1920 x 1080 pixels You can create dual screen applications just by using this product as a standalone device Equipped with a high performance Quad Core APU This product has a built in graphics processing unit GPU
33. ess to Setup and is only asked for when entering Setup f ONLY the User s password is set then this is a power on password and must be entered to boot or enter Setup In Setup the user will have Administrator rights The password must be n the following range Select Screen Minimum length T L Select Item Maximum length Enter Select Change Opt F1 General Help F2 Previous Values Adiministrator Password F3 Optimized Defaults User Password F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 26 Security menu The following items are available Administrator Password When you press Enter on this item you are required to input the password as below Create New Password ISS Confirm New Password FERE Enter a password of between 3 and 20 characters twice To nullify the password go to the Administrator Password Input Screen again Enter Current Password Create New Password Confirm New Password When you input old password in the initial item and then press Enter by inputting nothing to the new password item the password will be nullified User Password When you press Enter on this item you are required to input the password as below Create New Password ERES Confirm New Password EE Enter a password of between 3 and 20 characters twice Follow the same procedure as Administrator Password to nullify the password
34. file is created on an 8GB mSATA drive and is rewritten once every 10 seconds Rewritable lifetime 8 012 2 x 60 000 2 120 180 000 number of times Lifetime 120 180 000 60 10 x 60 x 24 x 365 38 year Example If a 4MB file is created on an 32GB Half Slim SSD drive and is rewritten once every 10 seconds Rewritable lifetime 30 533 2 x 3 000 2 22 899 750 number of times Lifetime 22 899 750 60 10 x 60 x 24 x 365 7 year 3 AC adapter The PWA 84AWD1 optional product is included in the package For details on the lifetime see the PWA 84AWDI user s manual which can be downloaded from the CONTEC website Replacement of expendables is handled as a repair there will be a charge Component life is not guaranteed value but only referential value FCC PART 15 Class A Notice NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference at his own expense WARNING TO USER Change or modific
35. ge North Bridge e Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 17 Chipset Menu The following sub items are available South Bridge Use this menu to specify South Bridge North Bridge Use this menu to specify North Bridge 9 CONTEC DS 380D Series User s manual 45 5 BIOS Setup South Bridge Aptio Setup Utility Copyright C 20xx American Megatrends Inc Chipset AMD Reference code Version Trinity PI 1 0 0 9 SB SATA Configuration SB USB Configuration Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 18 South Bridge The setting that can be selected on the South Bridge screen is described below The following sub items are available SB SATA Configuration Use this menu to specify the SATA settings SB USB Configuration Use this menu to specify the USB settings CONTEC 46 DS 380D Series User s manual 5 BIOS Setup SB SATA Configuration Aptio Setup Utility Copyright C 20xx American Megatrends Inc Chipset OnChip SATA Channel Enabled OnChip SATA Type Native IDE OnChip IDE mode Legacy mode
36. ges and Exit When you press Enter on this item you get a confirmation dialog box with a message similar to Exit Without Saving Quit without saving Pressing Yes continues to boot the system without saving any changes made in FLASH ROM Pressing No returns to the setup menu without records in FLASH ROM CONTEC 56 DS 380D Series User s manual 5 BIOS Setup Save Changes and Reset When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Save amp Reset Save configuration and reset Yes Nol Pressing Yes saves any changes made in FLASH ROM and reboots the system The next time the computer is booted the BIOS configures the system based on the configuration stored in FLASH ROM Pressing No it will return to setup menu Discard Changes and Reset When you press Enter on this item you get a confirmation dialog box with a message similar to Reset Without Saving No Pressing Yes reboots the system without saving any changes made in FLASH ROM Pressing No returns to the setup menu without records in FLASH ROM Save Changes When you press Enter on this item you get a confirmation dialog box with a message similar to Save Setup Values Save Configuration Nol Pressing Yes saves any changes made in FLASH ROM and takes you back to the setup menu Pressing No it will return to setup menu Discard Changes When you press
37. iently and comfortably Web Site Japanese http Www contec co jp English http www contec com Chinese http www contec com cn Latest product information CONTEC provides up to date information on products CONTEC also provides product manuals and various technical documents in the PDF Free download You can download updated driver software and differential files as well as sample programs available in several languages Note For product information Contact your retailer if you have any technical question about a CONTEC product or need its price delivery time or estimate information Limited One Year Warranty CONTEC products are warranted by CONTEC CO LTD to be free from defects in material and workmanship for up to one year from the date of purchase by the original purchaser Repair will be free of charge only when this device is returned freight prepaid with a copy of the original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group office from which it was purchased This warranty is not applicable for scratches or normal wear but only for the electronic circuitry and original products The warranty is not applicable if the device has been tampered with or damaged through abuse mistreatment neglect or unreasonable use or if the original invoice is not included in which case repairs will be considered beyond the warranty policy How to Obtain Service For replacement or
38. lect Change Opt Mass Storage Devices F1 General Help Storage Name Auto F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 13 USB Configuration Settings that can be configured in the USB Configuration are described in the table below Table 5 11 USB Configuraiton Item Options Description Enables Legacy USB support AUTO option disables legacy support if no USB Legacy USB Support devices are connected DISABLE option keeps USB devices available only or EFI applications XHCI Hand off Enable Disable USB3 0 XHCD Controller support This is a workaround for OSes without XHCI EHCI Hand off hand off support The XHCI ownership change should e claimed by XHCI driver n l he time out value for Control Bulk and Interrupt USB transfer time out transfers USB mass Storage device start Unit command time out Device reset time out Maximum time the device will take before it properly Auto reports itself to the Host Controller Auto uses default value for a Root port it is 100ms for a Hub port the delay is taken from Hub descriptor Device power up delay Manual CONTEC DS 380D Series User s manual 41 5 BIOS Setup NCT6106D Super IO Configuration Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced
39. option filter UEFI and Legacy Launch PXE OpROM policy UEFI only Launch Storage OpROM policy UEFI only Launch Video OpROM policy Legacy only Other PCI device ROM priority UEFI OpROM Select Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 25 CSM parameters The setting that can be selected on the CSM parameters screen is described below Table 5 18 CSM parameters Item Options Description This option controls if CSM will be launched tion filter 3 his option controls what devices system can boot to h PXE OpROM Controls the execution of UEFI and Legacy PXE OpROM s the execution of UEFI and Legacy Storage h Storage OpROM policy ROM Controls the execution of UEFI and Legacy Video h Video policy OpROM I devices other than Network Mass storage or Legacy OpROM efines which OpROM to launch Other PCI device ROM priority CONTEC 54 DS 380D Series User s manual 5 BIOS Setup Security Use this menu to configure system security settings Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Chipset Security Save amp Exit Password Description f ONLY the Administrator s password is set hen this only limits acc
40. outh Bridge under Chipset in chapter 5 Table 4 5 USB Connector Pin A Serial Port Interface SERIAL SERIAL RS 232C port This product is equipped with one serial port that complies with RS 232C This port has a baud rate of 115 200 bps max a dedicated data transmission buffer of 16 bytes and a dedicated data reception buffer of 16 bytes You can use the BIOS setup see chapter 5 to set the T O address and interrupt of this port and to disable the port The same I O address and IRQ cannot be shared with any other device Table 4 6 SERIAL B I O Addresses and Interrupts I O address Interrupt Table 4 7 Serial Port Connector onnector used on 10 pin RJ 50 male the product ED E GND Signal goon 7 Data terminal ready Request to send CONTEC 22 DS 380D Series User s manual 4 Each Component Function DVI Interface DVI Two DVI interfaces are provided The connector is named DVI DVI I 29 pin connector Table 4 8 DVI Connector 9 Pin No Signal name DATA2 DATA2 A2 SHIELD N C VSYNC DATA1 DATA1 DATAO SHIELD DATAT SHIELD xe CONTEC DS 380D Series User s manual 23 4 Each Component Function CONTEC 24 DS 380D Series User s manual 5 BIOS Setup 5 BIOS Setup Introduction This chapter discusses AM s Set
41. ow Table 5 2 Main Menu Selections Tem Set the Date Use Tab to switch between System Date Month Day Year Data elements Set the Time Use Tab to switch between System Time Hour Minute Second 2 Data elements CONTEC 28 DS 380D Series User s manual 5 BIOS Setup Advanced Use this menu to set the detailed function that can setting to your system Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Chipset Boot Security Save amp Exit PCI Subsystem Settings ACPI Settings CPU Configuration EuP ErP Power Saving Controller gt IDE Configuration Shutdown Temperature Configuration iSmart Controller USB Configuration NCT6106D Super IO Configuration NCT6106D HW Monitor Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 2 Advanced menu Settings that can be configured in the Advanced menu are described in the table below The following sub items are available PCI Subsystem Settings Use this menu to specify PCI Subsystem Settings ACPI Settings Use this menu to specify ACPI power management settings CPU Configuration Use this menu to specify CPU Configuration EuP ErP Power Saving Controller Use this menu to specify the power saving setting IDE Configu
42. r 92 PCI Bus Clocks 224 PCI Bus Clocks 248 PCI Bus Clocks VGA Palette Snoop Disabled Enables or disables VGA Palette Registers Enabled Snooping Disabled Enables or disables PCI device to generate PERR Gi t SERR Generation Disabled Enables or disables PCI device to generate Enabled SERR PCI Latency Timer 9 CONTEC DS 380D Series User s manual 31 5 BIOS Setup ACPI Settings Use this menu to specify ACPI power management settings Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced ACPI Settings Enable ACPI Auto Configuration Disabled Enable Hibernation Enabled ACPI Sleep State S3 Suspend to RAM Lock Legacy Resources Disabled lt Select Screen t Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 4 ACPI Settings Settings that can be configured in the ACPI Settings are described in the table below Table 5 4 ACPI Settings Item Options Description Enabled ACPI Auto Disabled Configuration Enable Enable or Disable ACPI Auto Configuration Disabled Enables or Disables System ability to Hibernate OS S4 Enable Hibernation DEDE Sleep State This option may be not effective with some OS Suspend Disabled Select ACPI sleep
43. ration Use this menu to specify IDE controller settings Shutdown Temperature Configuration Use this menu to set the shutdown temperature iSmart Controller Use this menu to specify the power on and power off settings CONTEC DS 380D Series User s manual 29 5 BIOS Setup USB Configuration Use this menu to specify USB Configuration NCT6106D Super UO Configuration NCT6106D HW Monitor Use this menu to view the hardware monitor Use this menu to specify the super I O settings CONTEC 30 DS 380D Series User s manual 5 BIOS Setup PCI Subsystem Settings Use this menu to specify PCI Subsystem Settings Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced PCI Bus Driver Version V 2 05 02 PCI Common Settings PCI Latency Timer 32 PCI Bus Clocks VGA Palette Snoop Disabled PERR Generation Disabled SERR Generation Disabled Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 3 PCI Subsystem Settings Items that can be configured for PCI subsystem settings are described in the table below Table 5 3 PCI Subsystem Settings 32 PCI Bus Clocks 64 PCI Bus Clocks 96 PCI Bus Clocks 28 PCI Bus Clocks Value to be programmed into PCI Latency 60 PCI Bus Clocks Timer Registe
44. re Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Chipset Security Save amp Exit Boot Configuration Setup Prompt Timeout 1 Bootup NumLock State On Quiet Boot Disabled Fast Boot Enabled Skip VGA Disabled Skip USB Disabled Skip PS2 Disabled CSM16 Module Version 07 69 lt Select Screen 11 Select Item GateA20 Active Upon Request Enter Select Option ROM Messages Force BIOS Change Opt INT19 Trap Response Immediate F1 General Help CSM Support Enabled F2 Previous Values F3 Optimized Defaults Driver Option Priorities F4 Save amp Exit ESC Exit Boot Option Priorities Boot Option x Device Name Hard Drive BBS Priorities CD DVD ROM Drive BBS Priorities gt CSM parameters Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 24 Screen with Fast Boot Set to Enabled The settings that can be configured when Fast Boot is set to Enabled are described in the table below Table 5 17 Smart Controller Screen with Schedule Slot Set to Power On Item Options Description Disabled Enabled Enabled Disabled Enabled The following sub items are available CSM parameters OpROM execution boot options filter etc CONTEC DS 380D Series User s manual 53 5 BIOS Setup CSM parameters Aptio Setup Utility Copyright C 20xx American Megatrends Inc Boot Launch CSM Always Boot
45. rt x Configuration x 0 1 NCT6106D HW Reie Chipset 45 SOU Bridge ecd e eR NEN EORR o e ie EE Me ee 46 SB SATA Configuration tense aee Pere apeks el RE ER EC ERE terne r 47 SB USB Confiour ation nn nn I ii 48 North Bridge Sss sira aaa asa ete HERR GERUCH yayaya GERE RETE GT EXER EYE 49 Socket 0 Information eene eter e PRI ROI BER NEE EEN 50 n E 51 ER 54 Security EE 55 Saye di EE 56 iv 9 CONTEC DS 380D Series User s manual 6 APPENDIX 59 LEE 59 7 LIST OF OPTIONS 61 9 CONTEC DS 380D Series User s manual v CONTEC DS 380D Series User s manual 1 Introduction 1 Introduction About the Product This product is a signage STB that is equipped with a 1 6 GHz R 452L AMD Embedded R Series Quad Core APU Accelerated Processing Unit The improved graphics capabilities of the APU make it possible to smoothly play full HD videos through the DVI I interface For storage this product is standard equipped with an 8GB mSATA drive or with a 32GB Half Slim SSD drive The body is so compact and supports SATA interface which can transport data at high speed It enables you to read high quality movie store so big data and transport data at high bit rate DS Series are the products assumed to be used at ordinary environment and market as Digital Signage Operating environment condition supply period maintenance period and other conditions are differ
46. se DS 380D DC741E Windows Embedded 8 1 Industry Pro 64bit English 4 Ifyou use the 1000BASE T be careful of the operating temperature For more details on this refer to chapter3 Installation Requirements 5 Use USB I F for the keyboard mouse 6 Use a power cable shorter than 3m For details see the PWA 84AWD1 user s manual which can be downloaded from the CONTEC website Table 2 2 Installation Environment Requirements DS 380D DCxxxx Operating temperature 7 0 45 C When using 1000BASE T 0 40 C Storage temperature 10 60 C Humidity 10 90 RH No condensation Floating dust particles Not to be excessive AC line 2kV 8 Signal line 1kV IEC61000 4 4 Level 3 EN61000 4 4 Level 3 Line noise Line noise s Static resistance electricity resistance Contact discharge 4kV TEC61000 4 2 Level 2 EN61000 4 2 Level 2 Atmospheric discharge 8kV IEC61000 4 2 Level 3 EN61000 4 2 Level 3 10 57Hz semiramplitude 0 15 mm 57 150Hz 2 0G 40 min each in x y and z directions JIS C60068 2 6 IEC60068 2 6 compliant 10G half sine shock for 11 ms in x y and z directions Impact resistance JIS C 60068 2 27 IEC 60068 2 27 compliant JIS E4031 compliant Classification 1 class B Class D grounding previous class 3 grounding SG FG continuity 7 For more details on this please refer to chapter 3 Installation Requirements 8 When PWA 84AWD1 is used Sw
47. state the system will enter when the ACEL Sleep State S3 Suspend to RAM SUSPEND button is pressed Lock legacy Resources Disabled Enabled or Disabled Lock of Legacy Resources Enable CONTEC 32 DS 380D Series User s manual 5 BIOS Setup CPU Configuration Use this menu to specify CPU Configuration Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced CPU Configuration Module Version 4 6 5 1 TrinityPl 019 AGESA Version 1 0 0 9 PSS Support Enabled PSTATE Adjustment PState 0 PPC Adjustment PState 0 NX Mode Enabled SVM Mode Enabled Select Screen C6 Mode Auto 11 Select Item Node 0 Information Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 5 CPU Configuration Settings that can be configured in the CPU Configuration are described in the table below Table 5 5 CPU Configuraiton Disable Enable disable the generation of ACPI Enabledl PPC PPC PSS and PCT objects PSS Support IPState 0 PState 1 PState 2 PState 3 PState 4 PState 5 PState 6 PState 7 PSTATE Adjustment Provide to adjust startup P state level PPC adjustment Provide to adjust PPC object NX Mode Enable disable No execute page protection Enabled function SVM Mode Disable Enable disable CPU Virt
48. surement points as shown below When making use of the product the air current should be adjusted to prevent that all the temperatures measured at the measurement points exceed the specified temperature 1 measurement points lt Vertical installation gt lt Horizontal installation gt Figure 3 7 Operating temperature The operating temperature specifications are met with the following installation environment requirements Installation direction Vertical installation Operating temperature 45 C 10BASE T 100BASE T 40 C 1000BASE T Air flow 0 5m s Load state CPU utilization 100 Memory storage Read Write Continuous operation of all interfaces COM LAN x 2 DVI I x 2 MIC LINE OUT t is assumed that USB mice USB keyboards or other USB 3 0 devices 900mA loads will be used with the three USB 3 0 ports 2D graphics and 3D graphics 1920 x 1080 are displayed CONTEC DS 380D Series User s manual 17 3 Hardware Setup CONTEC 18 DS 380D Series User s manual 4 Each Component Function 4 Each Component Function Component Name Figure 4 1 Component Name Table 4 1 Component Function POWER LED Power ON display LED DC IN DC power input connector MIC IN Mike in 43 5 PHONE JACK Ethernet 1000BASE T 100BASE TX 10BASE T RJ 45 connector x 2 USB 3 0 port connector x 3 Serial port connector 10pin RJ 50connector System Configuration
49. t modified by the user In the event of failure or abnormality foul smells or excessive heat generation unplug the power cord immediately and contact your retailer To connect with peripherals use a grounded shielded cable When transporting the product implement sufficient countermeasures to prevent the product from being directly subjected to vibrations and impacts You cannot clear the BIOS settings of this product If you change the BIOS settings and become unable to boot the computer it will have to be repaired If the battery needs to be replaced the product will have to be repaired In this situation contact your retailer When disposing of used batteries do so properly as instructed by the local government Component Life 1 Battery The internal calendar clock and CMOS RAM are backed by a Lithium primary battery The backup time at a temperature of 25 C with the power disconnected is 10 years DS 380D Series User s manual 5 1 Introduction 2 mSATA Half Slim SSD This model uses a MSATA or Half Slim SSD in the OS storage area The NandFlash can be rewritten 60 000 times or more for the mSATA drive and 3 000 times or more for the Half Slim SSD drive As a reference value the rewritable lifetime can be determined by the following calculation Rewritable lifetime number of times capacity MB management block size MB x 60 000 times number of management blocks rewritten each time Example If a 4MB
50. the AMI BIOS Setup Utility the Main Menu will appear on the screen By pressing the left or right arrow keys you will be able to move the tab of each item Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Chipset Boot Security Save amp Exit BIOS Information Memory Information Total Memory XXXX MB DDR3 System Date Mon MM DD YYYY System Time HH MM SS Access Level Administrator gt Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 1 Main Manu Setup Items You can choose the following tabs Main Use this menu to confirm the system basic configuration and set the language and time at the same time Advanced Use this menu to set the detailed function that can setting to your system Chipset Use this menu to specify the setting about your chipset D oot se this menu to specify the setting about the system boot ecurity ave amp Exit se this menu to load or save the setup item and to exit the setup menu U S Use this menu to set the password so that the system security can be protected S U 9 CONTEC DS 380D Series User s manual 27 5 BIOS Setup Main Use this menu to check basic system configuration Settings that can be configured in the Main menu are described in the table bel
51. tremely humid or dusty locations It is extremely dangerous to use this product with its interior penetrated by water or any other fluid or conductive dust If this product must be used in such an environment install it on a dust proof control panel for example Avoid using or storing this product in locations subject to shock or vibration that exceeds range of specification Do not use this product in the vicinity of devices that generate strong magnetic force or noise Such products will cause this product to malfunction Do not use or store this product in the presence of chemicals To clean this product wipe it gently with a soft cloth dampened with either water or mild detergent Do not use chemicals or a volatile solvent such as benzene or thinner to prevent pealing or discoloration of the paint This product s case may become hot To avoid being burned do not touch that section while this product is in operation or immediately after turning off the power Avoid installation in a location where people may come into contact with that section CONTEC does not provide any guarantee for the integrity of data on storage device Be sure to disconnect the power cable from the outlet before connecting cables to and disconnecting cables from the connectors and before configuring hardware settings such as switches To prevent corruption of files always shutdown the OS before turning off this product CONTEC reserves the right to refuse to service a produc
52. ualization Enabled Auto i C6 Mode Auto disable CPB Disable CONTEC DS 380D Series User s manual 33 5 BIOS Setup The following sub items are available Node 0 Information View memory information related to Node 0 Node 0 Information Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced Socket0 AMD R 452L APU with Radeon tm HD Graphics Quad Core Running 1620 MHz 887 mV Max Speed 1600 MHZ Intended Speed 1600 MHZ Min Speed 900 MHZ Microcode Patch Level 6001119 Cache per Core L1 Instruction Cache 32 KB 2 way L1 Date Cache 16 KB 4 way L2 Cache 1024 KB 16 way No L3 Cache Present Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 6 Node 0 Information 34 CONTEC DS 380D Series User s manual 5 BIOS Setup EuP ErP Power Saving Controller Aptio Setup Utility Copyright C 20xx American Megatrends Inc Advanced EuP ErP standby power control Keep standby power Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version x xx xxxx Copyright C 20xx American Megatrends Inc Figure 5 7 IEuP ErP Power Saving Controller The setting that can b
53. up program built into the FLASH ROM BIOS The Setup program allows users to modify the basic system configuration This setup information is stored in battery backed up RAM so the setup information is maintained even when the computer s power is turned off The rest of this chapter is intended to guide you through the process of configuring your system using Setup Starting Setup The BIOS is immediately activated when you first power on the computer The BIOS reads the system information contained in the FLASH ROM and begins the process of checking out the system and configuring it When it finishes the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system While the BIOS is in control the Setup program can be activated in one of two ways By pressing Del or F2 immediately after switching the system on or By pressing the Del or F2 key when the following message appears briefly at the bottom of the screen during the POST Power On Self Test Press DEL or F2 to enter setup If the message disappears before you respond and you still wish to enter Setup restart the system to try again by turning it OFF then ON You may also restart by simultaneously pressing Ctrl Alt and Delete keys 9 CONTEC DS 380D Series User s manual 25 5 BIOS Setup Using Setup In general you use the arrow keys to highlight items press Enter to sel

DS-380D Series User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents