SL300 SNOW DEPTH SENSOR
Contents
1. then switching back to OFF position will reset the measurement range between Minimum 0 000 to Maximum 10 000 meters 6 SL300 Snow Depth Sensor To determine the snow depth first subtract the voltage recorded from the maximum voltage read on the voltmeter during the step3 then divide the result by 5 if the full scale is set to 5V or 2 5 if the full scale is set to 2 5VDC Finally multiply the result of division by the maximum distance minimum distance Note Please always remember to return the MAX and MIN Switches back to OFF position for the normal operation of the device 2 7 Serial Interface There is an optional serial interface for digital data for a PC or Terminal Emulator with RS232 protocol The serial connection is done using Pin 3 and 4 of I O connector White and Blue Cables When the unit is turned on this uni directional 2 wire interface transmits the values of maximum and minimum adjusted distances refer to Calibration Procedure and after that continuously sends these data Measured Distance Travel time and Temperate At start MAX AAAA mm MIN BBBB mm Data Format While working X CCCC mm t DD DD ms T EE E a S300 Hyper ina File Edit View Call Transfer Help MAX 10000mm MIN 00000mm 4 0064 7mm T 17 0 t 04 01ms K 00647mm T 17 0 t 04 01ms X 0064 7mm T 17 0 t 04 01ms X 0064 7mm T 17 0 t 04 01ms 4 0064 mm T 17 0 t 04 0 Ims 4 01005mm T 17 0 t 06 10ms H 01005mm T2. 17 0 t 06 10ms 4 01005mm T 17 0 t 06 10ms 4 01005mm T 17 0 t 06 10ms H 01005mm 17 0 t 06 10ms H 01249mm 1 0 t 07 50ms 4 012423mm T 17 0 t 07 50ms H 01243mm T 17 0 t 07 50ms K 01243mm T 17 0 t 07 50ms 4 01243mm T 17 0 t 07 50ms K 01401mm T 17 0 t 08 42ms H 01401m m 17 0 t 08 42ms 4 01401mm 17 0 t 08 42ms 4 01401mm 17 0 t 08 42ms X 01 401mm T 17 0 t 08 42ms 4 01509mm T 17 0 t 09 05ms 4 01509mm T 17 0 t 09 05ms 4 amp 01509mm 17 0 t 09 05ms M 01509mm T 17 0 t 09 05ms 4 01509mm T 17 0 t 09 0 oms A 015 8mm T 17 0 t 09 46ms H 015 8mm 17 0 t 09 46ms 4 015 8mm T 17 0 t Q9 46ms 4 015 8mm T 17 0 t 09 46ms H 015 8mm T 17 0 t 09 46ms 4 01626mm T 17 0 t 09 7 amp 4ms 4 01626mm T 17 0 t 09 4 ms H 01626mm T 17 0 t 09 74ms H 01626mm T 17 0 t 09 74ms 4 01626mm 17 0 t 09 amp ms H 01659mm T 17 0 t 09 93ms H 01659m m 17 0 t 09 93ms 4 01659mm T 17 0 t 09 93ms 4 01659mm 17 0 t 09 93ms 8 01 659mm 17 0 t 09 93ms 4 016 9mm T 17 0 t 10 05ms _ Connected 0 01 22 ANSIW 115200 8 N 1 Figure 4 HyperTerminal display when SL300 connected to a PC through serial port SL300 Snow Depth Sensor Installation When mounting the sensor pay careful attention to the cone of the ultrasonic beam The beam width is 15 degrees which means that the diameter of the beam will be 30 of the distance to the target This means that after traveling 10 meters the beam diameter will be about 3 meters In this example the
3. F 855 grams L 21cm p 13cm Aluminum Stainless Steel SL300 Snow Depth Sensor 7 Warranty The SL300 Snow Depth Sensor is warranted by Felix Technology Inc to be free from defects in materials and workmanship under normal use and service for a year from date of shipment unless specified otherwise Felix Technology Inc s obligation under this warranty is limited to repairing or replacing defective products This warranty shall not apply to any Felix Technology Inc products which have been subjected to modification misuse neglect accidents of nature or shipping damage This warranty is in lieu of all other warranties expressed or implied including warranties of merchantability or fitness for a particular purpose Felix Technology Inc is not liable for special indirect incidental or consequential damages Products may not be returned without prior authorization To obtain a Return Materials Authorization contact Felix Technology Inc At 1 25 Edilcan Drive Concord ON LAK 3S4 Tel 905 760 0444 Fax 905 760 0044 Email sales felixtec ca Non warranty products returned for repair should be accompanied by a purchase order to cover the repair 12
4. FELIX SL300 SNOW DEPTH SENSOR User Manual SL300 Snow Depth Sensor Table of Contents l Cuneo DURO DRE ROREM 3 PN SUCI Too TI 3 2 1 Electrostatic Transducer eee 4 2 2 SL300 Analog Boatd erre ener 4 2 3 SL300 Digital Circuit Board eeeeeee 4 2 4 Calibration Procedure eee rennen nenne 6 Dig E HELO PE E A orent mem Misses bh Ride eren A RUD LM EEE eUNUE 8 e MEN EE ee E A E A EE 9 9 OECO uini teta Mti M 1 UNE lucu a 12 1 Introduction 2 Operation SL300 Snow Depth Sensor Felix Technology Inc SL300 Depth Sensor is an inexpensive solution for remotely measuring snow depth or water levels The sensor measures the distance from the sensor to a target The sensor works by measuring the time required for an ultrasonic pulse to travel to and from a target surface An integrated digital temperature sensor inside a solar radiation shield provides an air temperature measurement for properly compensating the distance measured An embedded microcontroller calculates a temperature compensated distance and performs error checking The distance is presented at the output as an analog signal between 0 to 5 Volts or 0 to 2 5V An Optional digital RS232 485 output provides travel time in ms distance in mm and air temperature in degree Centigrade Accurate measurement of snow depth poses many difficult problems The SL300 Snow Depth Sensor has proven very ef
5. Please refer to section 4 Maintenance 1 Apply the DC power 8 to 24VDC between Pin 1 Red Cable as V and Pin 2 Black cable as Ground or V 2 Connect a DC voltmeter DVM Plus lead to the Analog Output pin 6 or Green cable and the DVM Minus lead to Common pin 2 or Black Cable L 0 w Figure 2 Maximum and Minimum calibration using Dip switched on the digital board 3 Place the target at the maximum desired distance for the full scale voltage output Switch the MAX Switch DIP SW3 to ON position and wait for the detect LEDI indicator to blink once and then remain on Then return the MAX Switch DIP SW3 to OFF position The SL300 is now calibrated to your desired maximum target distance for full scale analog voltage output 5 or 2 5VDC 4 Place the target at the desired minimum distance for the zero voltage output Switch the MIN switch DIP SW4 to ON position and wait for the detect LED indicator to blink once and then remain on Then return the MIN Switch DIP SW4 to the original OFF position The SL300 is now calibrated to your desired minimum target distance for zero analog voltage output The function of LED 1 during the Calibration procedure LED blink on LED blink MAX ON MAX or MIN 2 OFF or MIN ON Figure 3 LED 1 function during the calibration procedure Switching both MAX and MIN switches to ON position simultaneously and
6. can be achieved as quickly as possible after transmit The very wide bandwidth and extremely high output allows the system to operate over a very wide distance range 2 3 SL300 Digital Board In the digital board a counter starts counting when a pulse is triggered by the processor The same pulse is used to transmit an ultrasonic pulse towards a target The output of the analog board which is an amplified received echo in response to transmit pulse is used to stop the counter The count value represents the distance ultrasound wave traveled from the transducer to the snow surface and return back to the transducer This count value and the temperature measured by the temperature chip are processed by the microprocessor to calculate the distance from the transducer to the object The final measurement according to the full scale setting is fed to an analog to digital converter to produce the analog voltage output of 0 to 2 5V or 0 to 5V In addition to analog output a stream of real time digital data containing the maximum and minimum distance setting temperature travel time and distance can be read through RS485 serial port 2 4 Digital Board Connectors Switches and LEDs CONI Felix Technology Inc C sk s 5L300 3 1 Tes GND H a Oz En i Veut 8 zi C Li m LF g Lf HO n Figure 1 Digital Board connectors Switches and LEDs 4 SL300 Snow Depth Sensor There are three connectors on the digital board as fol
7. e freely inside the enclosure throttle Open the enclosure by rotating the enclosure cap anticlockwise Warning Make sure that during rotation the temperature sensor and related cable stand still and do not turn together with the Cap Figure 6 Disassembling procedure for the maintenance SL300 Snow Depth Sensor 5 In order to access DIP switches firmly pull out the Analog and Digital boards together with extra care in order to avoid any damage to the ribbon cable between the two boards and also the cable to the depth sensor Continue pulling out the boards assembly until the DIP switches are accessible for the required setting or calibration Figure 7 Dip switches are accessible for the required setting and calibration The reverse procedure can be performed for assembling the unit back to the working status Warning After this reverse procedure please make sure that both the enclosure cap and the black gland are securely tightened to prevent moisture getting inside the sensor enclosure 10 Specifications Distance Range Accuracy over entire range Beam Pattern Repetition Rate Output Voltage Analog Load Current maximum Power Requirements Operating Temperature Weight Dimensions Housing Material Transducer Open Face 11 SL300 Snow Depth Sensor 0 45 6 10m 1 5 20 0 1 Typically 15 nominal 2 5 Hz 0 to 2 5VDC or 0 to SVDC 2 mA 5 to 24 VDC 85 mA 40 to 85 C 40 to 185
8. fective in measuring snow depth which makes it well suited for the other various applications too The ultrasound waves are emitted in bursts and received back at the transducer as echoes The instrument measures the time for the bursts to travel down to the reflecting surface and return This time will be proportional to the distance from the transducer to the surface and can be used to determine the level of liquid or snow The simple ultrasonic echo ranging system included in the SL300 is composed of three main parts the transducer the electronics analog module and the digital processor module The transducer is an electrostatic type transducer used to both transmit the signal and also receive the returning echoes The electronic modules contain all of the necessary circuitry to generate the transmit signal drive the transducer receive the echoes and process the information received by the transducer The distance from the transducer to the target is then computed by the digital processor module knowing the speed of sound in air and the time interval between the transmit signal and the received echo The SL300 operates over a distance range of 18 inches to 20 feet 0 45 to 6 10 meters increasing the receiving amplifier gain and decreasing the bandwidth with time to compensate for signal losses over the distance range To minimize the system s susceptibility to noise pick up a signal integration scheme is employed before the system l
9. lows e CONI Temperature Sensor Connector e CON2 I O Connecto Power Input Serial Interface Enable Analog Out e CON3 Interface to the analog Module The unit setting is achieved using four DIP switches e Ji DIP Switches are for setting the Analog Output Range Voltage Output Enable and Maximum amp Minimum Ranges SWI Analog Output range selection ON 0 to 5 Volts DC Output OFF 0 to 2 5 Volts DC Output SW2 Enable ON Free running device does not need HIGH Enable input OFF Device functions only when Enable input is HIGH TTL level SW3 Maximum range setting SW4 Minimum range setting SL300 s operation can be monitored using 2 LEDs e LEDI Mode detection LED Normal Operation mode Flashing Calibration mode setting the maximum and minimum ranges of depth measurement starts with OFF and after a delay it blinks once to show the end of the calibration process Refer to Calibration procedure e LED2 Power ON 2 5 SL300 wiring It is recommended to power down your system before wiring the SL300 Never operate the sensor with the shield wire disconnected The shield wire plays an important role in noise emissions and susceptibility as well as transient protection 6 Green Analog Output Analog Input of Datalogger SL300 Snow Depth Sensor 2 6 Analog Output Calibration Procedure To perform the calibration setting it is required to open the enclosure of the sensor
10. ocks onto an echo Once the threshold level of the integrator is reached a signal is generated to indicate a received echo The logic level outputs for the transmit signal and received echo can be used to perform control functions or calculate distance to the object SL300 Snow Depth Sensor 2 1 Electrostatic Transducer The key to the system is the unique electrostatic transducer It is composed of a very thin Kapton film diaphragm vacuum coated with gold to form the negative electrode The positive electrode is the coined aluminum back plate which also provides the resonant structure for the diaphragm Mechanical bias as well as electrical contact is provided by a stainless steel leaf spring 2 2 SL300 Analog Board The analog module uses a single interface to connect to the main Digital Board The module has an accurate ceramic resonator controlled 420 KHz time base generator that is being used with to provide the frequency of 49 4 KHz for the ultrasound transmission Also a variable bandwidth amplifier with digital controlled gain with minimum noise used to receive the echoes with an accuracy of better than 1 The transducer is driven with a 1 millisecond tone burst at 400 Volts peak to peak and 200 volts DC bias producing an output sound pressure level at 50 kHz of approximately 110 dB SPL at 1 meter The transmitting response is flat to beyond 100 KHz This provides the transducer with very fast damping so that ranging at high gain
11. sensor would need to be mounted at least half the distance of the beam diameter or 1 50 meters away from the mast Be careful to avoid obstructed beam paths To determine the minimum distance the sensor must be mounted away from the mast use this formula Cross arm length 0 3 x Height The SL300 Depth Sensor must be mounted perpendicular to the target surface Mounting the sensor at an angle will result in erratic and unreliable measurements To improve the accuracy of the sensor measurements mount the sensor as close to the target as possible This will minimize errors that are a percentage of the distance measured However the sensor cannot measure closer than 0 45 meters to the target and for the best result it should be mounted at least 1 meter away from the target w 1 foy m m Figure 6 Incorrect mounting pole Figure 7 Incorrect mounting Figure 5 Correct mountin 5 5 in the beam obstruction in beam RA Maintenance SL300 Snow Depth Sensor When properly installed the Depth Sensor should require minimal maintenance Disassembly is required for setting or calibration to change the transducer and inspect or replace the desiccant Disconnect the SL300 from the connector Dismount the sensor enclosure from the radiation shield by detaching the holder panel by removing two screws and then un tightening the throttle bolt screw on the radiation shield Loosen the black gland to let the temperature sensor move and rotat
Download Pdf Manuals
Related Search